HALF_DUPLEX deploys a shared line per backend. The hardware USART takes
the library's .half_duplex turn-around — RXD and TXD tied off-chip, each
reply byte held to transmit-complete before the line can be released
(m8 404 B, m328P 440, 1284P 460; the window poll runs through the
outlined release-line call at 18 or 22 cycles a poll, measured off the
built loops and held per chip by pureboot.window.halfduplex). The
software and autobaud links fold onto the RX pin — RX == TX spells the
same — and cost nothing: the frame's direction wrap is what the dropped
second-pin init paid, and the worst image in the space is unchanged at
the 1284s' 502 of 512, now with its one-wire twin proven equal across
the exhaustive matrix. The host gains --one-wire, the echo discard a
shared line requires: the adapter's echo is matched byte for byte and a
reply interleaving a blind write — a loader already in session
re-prompts inside the knock — is held for the reader. The device runner
models the shared line by direction (drives only while the firmware's
DDR reads input, decodes only while the firmware owns it, supplies the
host-side echo), extends the USART pin-ownership model to RXEN's hold
on RXD, and starts the pty USART from the datasheet's zeroed UCSR#B:
simavr's TXEN-set reset plus its clear-UDRE-on-TXEN-drop otherwise
wedges the first transmitter after a receiver-only program, which the
half-duplex window gate caught as a banner that never came. v7 is
tagged at its era's last commit; v8 changes nothing on the wire.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
libavr's calibrate() now bounds its measurement loop, starts the pulse
on an observed edge, and re-arms a rejected pulse on the remaining
budget instead of one-strike booting the application. The autobaud
images pay +16..20 B — every slot still fits, the worst now the 1284s'
502 of 512 — and the stock images are byte-identical, kept so by
fitting the loader's flag set per backend: -fno-ivopts stays on the
fixed-baud bodies it shrinks and comes off the autobaud body, where it
duplicated the calibration countdown into a 9-cycle loop against the
contracted seven.
One deployed constant moved and its gate caught it: the calibrate
wait's budget poll re-laid from ten cycles to nine (the exit branches
land where block layout puts them), so pureboot.window.autobaud
measured -10 % until AUTOBAUD_POLL_CYCLES and the README's derived
seconds were re-measured — the default autobaud window is 36 M cycles,
4.5 s at 8 MHz. Full gate green on all 37 chips; the README's autobaud
column carries each chip's rebuilt worst configuration, machine-checked
against the built trees.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Four cuts, none touching what the loader can do. The entry stub stops
re-doing the reset logic's own SP write where the datasheet guarantees
RAMEND (stack::hardware — the classic megas keep theirs). The autobaud
unit moves into GPIOR2:GPIOR1 wherever the chip has the pair: one-word
accesses, no RAM object, and the host's measured-clock peek follows it
by version and geometry. 'J' rides the unified decode, carrying a
selector it ignores so its address is the same two reads as every other
command — the tool sends the bare form to older residents. run_app stops
insisting on a body of its own. The fleet lands at 358–410 B stock and
438–474 B autobaud; the tightest image in the space — the 1284s'
autobaud on a USART's own pins with the OSCCAL trim — drops from 510 to
484 of its 512. Every chip's suite is green on the wire that changed,
and the README's table is machine-checked against the built images.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
The RC-oscillator answer's device half (dev/tasks.md in libavr): OSCCAL joins
pureboot_add_loader() as one optional byte, written at the top of run() before
the WDRF bail so the watchdog hand-over inherits the corrected clock too.
Orthogonal to the backend — an autobaud build may carry it purely for the
application. No value, no code: the stock image differs from v5 in exactly
the version's two bytes (the stamp and the 'b' immediate).
Measured: +6 B where OSCCAL takes sts (328P, 404→410), +4 B in low I/O
(t85, 402→406); the tightest image in the space (1284 autobaud on USART
pins, 504) carries the sts form at 510 of 512. New gates: the OSCCAL size
points on every chip, the wire-observed trim byte on both addressing
classes (test/pbosccal.py, red-green), and the autobaud unit pinned to
ram_start (test/check_unit.cmake, red-green) — the address --info's
measured-clock read is about to rely on.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Pins move the image for exactly one reason — a bit-banged link on a USART's own
pins has to release that USART — and the matrix said outright that they were no
axis, so the tightest configuration in the space was one nothing built. Not
subtly, either: the 1284's slot ends at flash end, so that build does not merely
exceed the size test's limit, it fails to link. pureboot_{sw,autobaud}_on_usart
{0,1} are gate points in both matrix modes now, and the exhaustive sweep carries
the pins across its whole cross product. The hand-measured table is the gate's
output: 506 B of 512 for the 1284 autobaud on USART0's pins, 504 on USART1's.
pureboot.mute drives the defect itself — an application hands over with USART0
still enabled and the loader on those pins must still answer. Reaching that
needed the runner to know an enabled USART owns its TxD, which simavr does not
model at all: it wires a USART through IRQs and never takes the pin from the
port. It also brings UCSRnB up with TXEN already set where silicon clears the
register, so the runner restores the reset value for the USART it models — the
mute must come from the application, not from power-on. The fixture stays
silent, since nothing is listening on the USART it brings up.
test_handshake.py, written where no gate could run it, is pureboot.handshake.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
R/r/w/F collapse into G and g over a selector byte naming the space — flash,
EEPROM, data, fuse, SPM — with the flash bank in its high nibble. Four command
bodies, four transfer loops and four argument decodes become one of each, and
W joins the same decode instead of keeping an address form of its own. The
loader shrinks while gaining everything below: on the 1284P the stock build
goes 480 -> 432 B and the software one 496 -> 450.
What the freed space buys:
- Data space. On AVR one pointer spans SRAM, the register file and the whole
I/O space, so G over space 2 reads all three. pureboot keeps zero static
RAM and pushes no register, so at loader entry an application's SRAM is
still what the application left there — this is a post-mortem, not just a
poke hole. As its own command it needed a dispatch arm and a loop; as one
more space it is a single ld/st.
- Host-issued SPM. W fills the page buffer and stops; erase, write and RWW
re-enable are writes to space 4, which reach the same fused store-and-SPM
pair through the transfer's own address and data. Any SPM operation, lock
bits included, is now reachable and the loader carries no page-commit logic.
The four-cycle SPMCSR-to-SPM window is why that primitive stays fused: no
host can hit it across a serial link, and that — not the byte count — is
the floor on how low-level a bootloader's primitives can go.
- Byte addresses everywhere. The bank in the selector retires the
word-addressed wire the >64 KiB parts needed, so the 1284s stop being the
outlier.
SERIAL autobaud is a third backend on the same loader, over libavr's
software_autobaud: no clock, no baud, one binary per chip for every F_CPU and
every rate. Activation counts poll iterations rather than seconds and bounds
every wait, so a stray pulse cannot hold an unattended device.
b answers with the version and signature only; the host derives geometry from
the signature, which is what an autobaud build requires anyway. An update image
is a bare slot with no device to ask, so every image carries a six-byte stamp —
the same bytes b answers with, and the source of both — that the loader never
reads from flash and the host refuses to install a mismatch against. The
running-slot write guard moved onto the SPM commit, which covers erase and
write both where guarding W covered neither directly.
The position-independence lint now proves the property instead of a proxy for
it: the image must come out byte-identical linked at a different base.
-fno-move-loop-invariants left the tuned flag set — it was fitted to a command
loop carrying four transfer bodies and costs bytes now that it carries one.
Verified: the exhaustive matrix on all 37 chips (every clock x every baud x
every backend, non-standard rates included, plus the autobaud build) —
8174 size checks, no failures, tightest fit the 1284s' autobaud at 510 of 512.
Behavioral suites green on every chip class: t13a 10/10, t85 11/11, m8 13/13,
m16a 13/13, m48pa 13/13, 328P 23/23, 644A 17/17, 1284P 17/17. Data-space
round trip through --peek/--poke and the autobaud handshake are both red-green
proven.
The two prototype sources and their findings file go; the README carries the
protocol and dev/done.md in libavr carries the reasoning.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Measure the host's bit timing at runtime from a 0xC0 calibration pulse, so one
clock-agnostic image per chip runs at any F_CPU — the RC-oscillator deployments
no longer need a per-clock build.
Two source files, differing only in the write-guard/purity tradeoff:
pureboot_autobaud_pure.cpp (the measured unit in the GPIOR I/O scratch
registers, running-slot write guard dropped, 508 B on the 1284) stays strictly
pure; pureboot_autobaud_reg.cpp (unit in one global register variable, guard
kept, 512 B) keeps every feature at the cost of that single GRV. Both fit
512/510 on all 37 chips and share two licensed simplifications: a slimmed info
block (version + signature; the host derives geometry from the chip database)
and a single-byte activation knock.
pureboot/autobaud.md records the decision, the hand-assembly floor (506 B) that
set the target, and the compiler-knob path to it. Size-tested on every chip via
pureboot_add_autobaud(); the fixed-baud loader is untouched. Sim validation, the
host calibration handshake, and real-hardware acceptance remain.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Every plausible oscillator against every rate it reaches against every
backend, on one chip per size-bearing class, under --full only. The baud
ladder becomes a reachability predicate the enumeration filters on, so an
unreachable point drops out instead of aborting the configure.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
The word-addressed 1284s were the one family deploying in a 1 KiB slot,
because the far-flash machinery (ELPM reads, RAMPZ page commands, a
word-addressed wire) did not fit 512 B. It does now: 478 B stock, 494 B in
the heaviest configuration the build can produce. They take the 644s'
geometry, where the smallest boot section holds the resident slot and its
staging slot together. The loader's version goes to 3; the host tool did
not change, so its own version stays 2 and only the window it speaks
widens.
Most of the saving is one restructure. The info block and a flash read are
the same act, so giving all four streamed commands one address-and-count
path leaves exactly one call site for the flash streamer: it inlines into
the never-returning command loop and its 24-bit cursor stops being saved
and restored around every transmit. Around it, the ack byte moved out of
line, the wire's byte pair is bit_cast into the word it already is, the
fuse loop ends on its count, the info block's in-slot offset is taken as
the one-byte relocation it is, and -fno-expensive-optimizations gives way
to -fno-move-loop-invariants -fno-tree-ter. Every chip shrank 14-18 B.
The size matrix grew the axes it was missing: the USART1 instance across
the whole clock ladder, and the shape a slow baud gives a software UART —
past 255 delay iterations libavr takes the 16-bit delay loop, which the
ladder default never selects and which was 4 B over the 1284's slot the
first time it was built.
The protocol fixture stopped deriving the loader entry from the flash
size; on the 1284s it had been jumping a slot low and reaching the loader
only because erased flash walked it up.
Docs and comments were consolidated across the port in the same pass: the
README carries a per-chip size table instead of prose, and prose that
restated the code is gone — 190 lines, no behaviour with it.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
The temporary page buffer is write-once per word, so a page filled over
one an earlier writer left dirty programs the stale words. The same
datasheet clause carries the cure: the buffer auto-erases after a page
write (§26.2.1; §19.2 on the tinies), so the corruption clears itself by
happening, and rewriting the page programs correctly.
The loader therefore clears the buffer nowhere. The tinies' CTPB and the
m48s' RWWSRE discard are gone; the boot-sectioned megas keep only the
trailing RWWSRE they need anyway to re-enable the RWW section for
read-back, which discards the buffer as a side effect and keeps them off
the path entirely. 434 B on the tiny13s, 438-442 on the tiny25/45/85,
430 on the m48s; the megas are unchanged, the 1284s still 506.
The host takes over the guarantee: a flash page that reads back wrong is
rewritten up to RETRIES times before the run stops. Both read-back paths
repair — verify_pages for programming, and write_differing, which is the
loader-update path where a page left wrong is a half-written loader slot.
That one is not hypothetical: deleting the discard made attiny85
pureboot.rehome fail deterministically there, the only flow still
assuming the old contract.
Protocol-visible, so README's W command says it: one W may program the
wrong bytes after a refused page, or after an application that
self-programmed entered without a reset, and a host that programs without
reading back cannot trust it.
Tests: pureboot.dirty drives the case the loader declines to guard — the
fixture application dirties every buffer word and jumps in with no reset
(hardware forbids that on a boot-sectioned mega, but simavr dispatches SPM
from anywhere, which is what makes it constructible) — and asserts a bare
verify sees the corruption, the repairing verify fixes it in one rewrite,
and it stays fixed. pbreloc asserts the same shape after a refusal.
test_planner covers the bound against a fake device: one bad write
repaired in a single rewrite, a page that never comes good stopping after
exactly three.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Clock, baud, serial backend (hardware USART 0/1 or the software UART on
any pins) and the activation window all resolve through one CMake
function, pureboot_add_loader() in pureboot/CMakeLists.txt — the unit a
downstream project consumes. The default baud is the fastest standard
rate within 2.5 % (the same best-divisor search libavr's solver runs),
gated on software builds by the polled receiver's 100-cycles-a-bit
floor; every explicit pick is re-checked by the compile's static asserts.
The size matrix builds each axis that can move the image — backend x
clock ladder x USART instance, per chip — against the slot budget, and
two nondefault deployments run the whole protocol suite live: the 328P
on its shipped 1 MHz fuses over software serial on TX=PB1/RX=PB5
(pureboot.custom), and the 644A over USART1 (pureboot.usart1). The sim
runner takes -l to bridge any link, paces a fully quiet bridge toward
real time (a free-running 8 M-cycle window loses the reset-race knock),
and the fixture application speaks the deployment it is built for.
The loader itself shed bytes on the way: the return-address high byte
spelled through byteswap (the double swap folds to the one-byte pick),
the info-block address composed instead of bit_cast, and libavr's new
polled-UART helpers replacing the port's uart::detail reaches. Every
combination fits: 458-506 B across the megas' whole matrix, 470-484 B
on the tinies, 556-562 B in the 1284s' 1 KiB slot.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
