avr/bootloader
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Compare commits

base: avr:stk500v2-library-wip
Branches Tags
avr:master avr:main avr:stk500v2-library-wip avr:autobaud
avr:v8 avr:v7 avr:v6 avr:v5 avr:v4 avr:v3 avr:v2 avr:v1
..
compare: avr:v8
Branches Tags
avr:main avr:stk500v2-library-wip avr:autobaud avr:master
avr:v8 avr:v7 avr:v6 avr:v5 avr:v4 avr:v3 avr:v2 avr:v1

93 Commits
stk500v2-l ... v8

Author SHA1 Message Date
BlackMark
eb213e1025 one-wire: a lost echo and a dead line are not the same report 
The blind-write path said "lost to the device's ack" for any missing echo, and
the count is what distinguishes two different faults. Some bytes lost is the
device's ack winning the line against the host's series resistor — ordinary,
and what the knock retry absorbs. *Every* byte lost is nothing coming back at
all, which means the line is not free: a pin held low, a wedge, or an RX that
is not on it.

Found pointing the wrong way on purpose-built hardware. This rig's LED demo
ends by driving every port pin low, and one of them is the shared link — so a
knock into a finished demo got no echo whatsoever and was told the device had
acked, when nothing had answered and nothing could. Same retry either way, but
blaming an ack that never happened sends the reader to the protocol when the
answer is a pin.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-31 18:32:18 +02:00
BlackMark
3e4bfbaf48 pbhw: the marker check assumed a board whose port-open is not a reset 
Its comment said "opening the port does not reset a board whose DTR is
unwired, so this simply listens" — true of the tiny it was written against,
false of an Arduino, and this is the generic harness. Where DTR is wired to
reset, that open resets the part and the activation window comes first, so a
fixture emitting its banner once says it on the far side of a wait the suite
cannot know the length of: the window is a compile-time constant and nothing
on the wire reports it. The suite read the silence as an application that
never ran, on a board where it demonstrably had.

So --marker-wait, defaulting to the 2.5 s that was hardcoded, and a failure
that names the window as the candidate rather than leaving the next person to
suspect the loader. The other half is the fixture: PUREBOOT_HEARTBEAT makes
the observation independent of when the listener arrives, which is what the
rig's own builds now pass.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-31 17:12:08 +02:00
BlackMark
579ca81b27 one-wire: the knock's lost byte is the wiring, and the diagnosis was unreachable 
Measured on an ATtiny13A with the link folded onto PB3 and the FTDI's TX
reaching it through 1 k: a knock aimed at a loader already in session loses
its second byte every time, 8 runs of 8, never intermittently. The first byte
draws a prompt while the second is still going out and the device's push-pull
ack wins the line against the resistor, so that byte is destroyed rather than
delayed — which is what the README predicted and the sim bridge cannot show,
since it arbitrates the line by queueing.

The recovery for it existed and could not run. Two defects:

OneWirePort.write read its echo with read_exact, whose contract is to raise, so
the "one-wire echo missing — is the adapter's RX tied to the line?" message was
unreachable on any line that simply fell quiet, and a bare "timeout: got 0 of 1
bytes" surfaced in its place. The one message the class exists to produce could
never be produced. The read is speculative and is now read_available.

And any raise from write aborted _handshake before the retry loop that exists
to absorb exactly this, whose docstring already claimed it "converges into an
already-live session" — true on a pty, impossible on real wiring. The knock is
now the one write marked blind: a missing echo there is a property of the
shared line, counted and reported under -v rather than raised. Every other
write is ack-paced and cannot collide, so a missing echo there still means an
RX that is not on the line, and still raises.

Both gates green on Windows (31/31 m328p, 16/16 t13a); on hardware the
reconnect now converges on the first knock, the surviving prompt being all the
handshake needs.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-31 16:29:17 +02:00
BlackMark
5d520a1ff9 pbhw: --one-wire never reached the suite's own sessions 
The flag was plumbed through pbrig.Deployment to the host-tool subprocess
calls and nowhere else, so identity() and scan() opened a raw port and drove
a shared line as though it were two wires. On real one-wire hardware the
adapter's echo answers the knock before the device does, so the suite would
have died at its very first check — "the loader never answered; nothing below
can be trusted" — for the one deployment the flag exists to test, and every
result after it is gated on that check passing.

Both now open through pbrig.Rig.open_port(), which applies the deployment's
link mode. The gap underneath was that only the subprocess path could reach
those facts at all; anything driving the protocol in-process had to restate
them, and did not.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-31 13:25:46 +02:00
BlackMark
f71d76a815 pureboot v8: one-wire on every backend 
HALF_DUPLEX deploys a shared line per backend. The hardware USART takes
the library's .half_duplex turn-around — RXD and TXD tied off-chip, each
reply byte held to transmit-complete before the line can be released
(m8 404 B, m328P 440, 1284P 460; the window poll runs through the
outlined release-line call at 18 or 22 cycles a poll, measured off the
built loops and held per chip by pureboot.window.halfduplex). The
software and autobaud links fold onto the RX pin — RX == TX spells the
same — and cost nothing: the frame's direction wrap is what the dropped
second-pin init paid, and the worst image in the space is unchanged at
the 1284s' 502 of 512, now with its one-wire twin proven equal across
the exhaustive matrix. The host gains --one-wire, the echo discard a
shared line requires: the adapter's echo is matched byte for byte and a
reply interleaving a blind write — a loader already in session
re-prompts inside the knock — is held for the reader. The device runner
models the shared line by direction (drives only while the firmware's
DDR reads input, decodes only while the firmware owns it, supplies the
host-side echo), extends the USART pin-ownership model to RXEN's hold
on RXD, and starts the pty USART from the datasheet's zeroed UCSR#B:
simavr's TXEN-set reset plus its clear-UDRE-on-TXEN-drop otherwise
wedges the first transmitter after a receiver-only program, which the
half-duplex window gate caught as a banner that never came. v7 is
tagged at its era's last commit; v8 changes nothing on the wire.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-31 02:32:11 +02:00
BlackMark
47419400f6 build: the pin advances over the one-wire serial feature 
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-31 02:31:55 +02:00
BlackMark
bad8b6b43e build: the pin advances over the bounded calibration 
libavr's calibrate() now bounds its measurement loop, starts the pulse
on an observed edge, and re-arms a rejected pulse on the remaining
budget instead of one-strike booting the application. The autobaud
images pay +16..20 B — every slot still fits, the worst now the 1284s'
502 of 512 — and the stock images are byte-identical, kept so by
fitting the loader's flag set per backend: -fno-ivopts stays on the
fixed-baud bodies it shrinks and comes off the autobaud body, where it
duplicated the calibration countdown into a 9-cycle loop against the
contracted seven.

One deployed constant moved and its gate caught it: the calibrate
wait's budget poll re-laid from ten cycles to nine (the exit branches
land where block layout puts them), so pureboot.window.autobaud
measured -10 % until AUTOBAUD_POLL_CYCLES and the README's derived
seconds were re-measured — the default autobaud window is 36 M cycles,
4.5 s at 8 MHz. Full gate green on all 37 chips; the README's autobaud
column carries each chip's rebuilt worst configuration, machine-checked
against the built trees.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-30 22:49:55 +02:00
BlackMark
5d1b4497d4 build: the libavr pin advances over the drain and delay contracts 
The hand-over drains move to the explicit drain_unbounded() — both link
adapters drain only after their own write, so the frame is in flight by
construction and the bounded default's countdown would be dead bytes;
the images stay byte-identical. window_polls() states its arithmetic
through dev::cycles_for with the whole window converted before the
per-poll division — one truncation instead of one per second, same
instructions, only the countdown's immediate moves. Every size in the
matrix is unchanged; the full gate is green on all 37 chips.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-30 17:31:22 +02:00
BlackMark
a743ea64a3 tool: a size collision across build trees is an error, not a coin toss 
sizes.py merged every owned tree's rows and let the last one win, so a
stale reflect tree — last built before the window constants moved —
reported the atmega8's old stock size over the fresh build and failed
the README check with yesterday's number. Generated and reflect must
answer with the same bytes (the identity invariant), so the same target
measuring two sizes is a stale tree or an identity breach; collect()
refuses now, naming both trees. The stale reflect trees are removed —
the reflect sweep rebuilds them.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-30 16:32:35 +02:00
BlackMark
aa66cfccff pureboot: the poll-cost lookup rides the baud parameter 
usart_of<0> is an incomplete type on the USART-less chips, and a static
member initializer with only non-dependent operands is checked when the
template is parsed, not when it is instantiated — so the address probe
broke every tiny build without hardware_link ever being named. The
lookup moves into a member function template taking the link's own baud
parameter, the dependence carrier that defers it to instantiation.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-30 16:13:44 +02:00
BlackMark
459d463283 pureboot: the classic megas' idle poll is a bit-skip — 7 cycles, and their stock window goes wide 
The window gate's first full sweep caught it on the atmega8: 6.22 s
measured against 8 declared, the exact 7/9 of a poll modeled as an
extended-I/O lds + skip on a chip whose UCSRA sits in bit-addressable
I/O and compiles to a 2-cycle skip. poll_cycles now follows the status
register's home (7 below 0x40, 9 above). At 16 MHz over 7 cycles the
poll count no longer fits uint24_t, so the classic megas' stock windows
take the wide countdown — 8.000 s measured on all three, +4 B of stock
image (m8 362, m16/m32 364), README stock rows updated.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-30 16:11:34 +02:00
BlackMark
8e7cc86fb3 pureboot: the activation window gets a behavioral gate, and honest per-poll constants under it 
The window's per-poll cycle counts were hand-counted for a uint32_t
countdown, but every default window fits uint24_t, whose decrement chain
is one sbci shorter — so deployed loaders ran 9/10ths of their stated
seconds (a 328P's 8 s was 7.2 s on the wire). No golden-asm pin can hold
this: the loops compile in consumer context. pbwindow.py measures the
behavior instead: it installs a real application beside the loader
through the host tool's own plan_flash (surgery included), starts the
simulator with the line idle, and reads the cycle of the first transmit
— the application's banner, so that cycle is the window. Held at plus or
minus 2 percent per chip (pureboot.window), red at -10.0 percent against
the old constants, green with poll_cycles now counted for the narrow
countdown (hardware 9, software 7; window_polls() solves narrow-first
and adds the wide loop's cycle where the count forces uint32_t — a count
narrow only at the wide cost stays wide, so the choice cannot
oscillate). The autobaud window is its poll budget at the measured ten
cycles a poll, gated the same way (pureboot.window.autobaud), and the
README carries that arithmetic now. No version bump: timing-window
precision is not meaningful behavior, v7 stays.

The gate flushed out two runner gaps. The software bridge accepted any
falling edge as a start bit, so the device's own TX-init glitch decoded
as a stray byte; it re-samples mid-bit now and abandons a false start,
as silicon does. And after avr_reset, the idle-line re-raise was
silently dropped: ioport pin irqs are IRQ_FLAG_FILTERED and the irq's
cached value survives the reset the port latch does not, so the device
read the line stuck low, calibrate() measured reset-to-first-edge as one
wrapping pulse, and the first knock after a reset could boot the
application instead of locking — the intermittent autobaud failure.
bridge_reset forces a real transition (0 then 1, no cycles between).

The README's Autobaud column now carries each chip's worst
configuration — autobaud with OSCCAL baked, on a USART's own pins where
the chip has one (tinies: autobaud + OSCCAL) — the numbers the existing
pureboot_autobaud_osccal[_on_usart0] matrix points already gate;
sizes.py checks the column against exactly those targets. Tool sizes
and window prose updated with it.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-30 16:05:42 +02:00
BlackMark
c8ac61779e tool: survive our own leftovers — drain the fresh port, shorten the identity read 
--stay leaves the loader's final prompt in the USB pipeline; a fresh
invocation on a board that resets when its port opens then flushes too
early, trusts the stale prompt, and spends the new activation window on
a 2-second identity read against a device that never heard its knock —
collecting the application's banner as an unknown signature. Three
host-side moves, no device bytes: the line is drained until quiet
(bounded, 250 ms) before the port's first knock — once per port, since a
mid-session re-knock faces no foreign bytes and its own window is
already burning; the identity read_exact drops 2.0 to 0.5 s, dozens of
times the worst real answer, so any false prompt match leaves room for
the retry that already works; and the tool version drifts to 8. The
StaleDTRPort fixture models the whole moment — stale prompt in transit,
reset holding the device off the line, a finite window, the banner —
red against the old tool in exactly the field shape (unknown signature
from banner bytes), green now; LoaderPort answers its prompt to the
knock rather than to a read count, which the drain exposed as a
call-order coupling.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-30 16:05:16 +02:00
BlackMark
4362886c39 build: the libavr pin advances over the trait projection 
The de-string-2 pass upstream: every peripheral block behind generated
instance traits, int-keyed, the string layer gone. The port's share of it
is two spellings — the char usart_digit that existed to be pasted into
register names becomes the int unit the usart template now takes, and the
tsb tiers' one reg<"UBRR0"> is the flat hw::ubrr0 — plus the pbapp
harness probing has_usart<0>() instead of instance-name strings. Nine
loader codegen families rebuilt green through their full workflows (size
matrix and simulator protocol suites included); every image holds its
recorded size.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-29 20:08:10 +02:00
BlackMark
0513d07e87 build: the libavr pin advances to current main 
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-29 07:24:10 +02:00
BlackMark
d4ab28aa17 build: the libavr pin advances to current main 
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-29 06:48:37 +02:00
BlackMark
b60f182105 review: the port's findings — the version map speaks v7, costs told true 
The in-file version window now carries the v7 line its own comment
claimed to hold; the GPIOR note counts words, not instructions; the
USART-release cost and citation match the silicon (two bytes on the
classics, §20.6.3); and the 512-byte claim reads as the slot bound it
is. The libavr pin advances over the review pass — images byte-identical.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 20:05:42 +02:00
BlackMark
5bc35a9733 build: the libavr pin advances over the instance traits 
Byte-identical images — the traits resolve the same database indices the
retired string forms did; the tightest image is compared outright.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 17:18:07 +02:00
BlackMark
8f6319c068 pureboot 7: the same features in fewer words on every chip 
Four cuts, none touching what the loader can do. The entry stub stops
re-doing the reset logic's own SP write where the datasheet guarantees
RAMEND (stack::hardware — the classic megas keep theirs). The autobaud
unit moves into GPIOR2:GPIOR1 wherever the chip has the pair: one-word
accesses, no RAM object, and the host's measured-clock peek follows it
by version and geometry. 'J' rides the unified decode, carrying a
selector it ignores so its address is the same two reads as every other
command — the tool sends the bare form to older residents. run_app stops
insisting on a body of its own. The fleet lands at 358–410 B stock and
438–474 B autobaud; the tightest image in the space — the 1284s'
autobaud on a USART's own pins with the OSCCAL trim — drops from 510 to
484 of its 512. Every chip's suite is green on the wire that changed,
and the README's table is machine-checked against the built images.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 17:02:38 +02:00
BlackMark
a3ea099105 pureboot: the detail reaches become the library's own API 
The three things this repo took from under libavr's counter are now over
it, and the local copies fold away. The USART release on a software
link's pins is the library's init contract (its guard here becomes a
deletion, byte-identical images held by the gate); the WDRF routing test
is power::peek_reset_cause().watchdog instead of a hand lookup of the
flag's register; the tsb tiers' baud arithmetic is the public solver.
libavr pin advances over those three additions.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 16:12:35 +02:00
BlackMark
c535c4756c pureboot: the activation countdown in the narrowest type that holds it 
The fixed-baud window counted down a uint32 where almost every window fits
24 bits; the countdown now takes avr::uint24_t when the poll budget allows
(the autobaud budget's own choice), uint32 past 16.7M polls — four bytes
off every fixed-baud image on every chip, the full suites green on the
changed window. The README size table is refreshed — its autobaud column
had also gone stale by the no-assembly pass's measurement-loop win, which
nothing gated: sizes.py check-readme now runs as the gate's final stage,
where every tree is freshly built and the table can actually be held.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 14:47:29 +02:00
BlackMark
321ff8a4ee test: the device runners speak the C++ the rest of the repo does 
pureboot_device and the tsb device, C until now, rewritten in C++23 with
every modeled behavior intact — the PGERS Z-mask and m48-discard ioctl
wraps, the GPIO bridge's timing and pacing, the tiny NVM's write-once
buffer, pin ownership, and the PB_PTY/TSB_PTY lines the harnesses parse.
The one linkage fact worth a comment: simavr's parts headers (uart_pty.h)
carry no C++ guards where its core headers do, so those includes sit in an
extern "C" block. Warning-clean at -Wall -Wextra on the build line; the
full protocol suites on all four sim-driven chips prove the conversion.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 13:59:03 +02:00
BlackMark
531ae6c8dc build: the libavr pin advances over the audit rounds 
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 10:52:05 +02:00
BlackMark
b3f41caf6e audit: round three on the port — the hardware scan check fails soft 
A rig hiccup mid-walk records the scan check as failed and lets the suite
continue, matching its siblings' envelope; a nonexistent --port path
reports as an error instead of a traceback.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 10:31:32 +02:00
BlackMark
7716e1e291 audit: the port's pass — the scan that could not walk, and the drift a generator ends 
--scan's walk was unwalkable on POSIX: probe rates have no termios
B-constant, so the first off-nominal probe raised out of the loop. The port
speaks termios2 BOTHER now (red-proven on a pty at 9984 Bd), the probe's
open lives inside the walk's error handling, an fd no longer leaks on an
unmakeable rate, and the swallowed unknown-signature reply is named at
timeout instead of reported as silence. CMakePresets.json's generator emits
the submodule toolchain path it had drifted from — a hand edit on a
generated file, exactly the class rule 10 exists for — and presets.generated
gates the pair from here on (the  marker CMake rejects at the
presets root stayed out; the check is the guard). The over-slot image guard
the tsb runner gained reaches the pureboot runner too; the GPIO bridge's
delivery comment states the hardware truth (RXC at the stop bit's sampling
point); the hardware suite gains the scan check — the one place the rate
physics is real; and the libavr pin advances over both audit rounds.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 10:12:17 +02:00
BlackMark
1b18f10f4e docs: the OSCCAL axis, --scan, and the RC-oscillator deployment risk 
Configuration gains the OSCCAL row; Deployment says what the build cannot
see (±10 % factory trim against a frame's ~±4 %, and silence that reads as
wiring); the update section names an OSCCAL bake as a link change in effect,
declared with --staged-baud; the host-tool section documents --scan and the
measured clock --info adds on an autobaud session; the version map gains 6.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 01:03:15 +02:00
BlackMark
52c4cdab32 pureboot.py: --scan walks a silent loader's rate; --info decodes the clock 
The RC-oscillator answer's host half. --scan probes ±10 % around the built
rate in 2 % steps, nearest first, one activation window (one reset) per
probe: a fixed-baud loader whose oscillator drifted answers at the ratio,
and the report gives the session workaround (--baud), the offset, the
OSCCAL direction at ~1 %/step, and the autobaud way out. The walk and the
advice are logic-tested (test_scan.py, red-proven on the trim direction) —
a pty carries bytes at any rate, so the wire cannot arbitrate them.

On an autobaud session --info now reads the measured bit period from
ram_start — the geometry table gains that column — and undoes the unit's
encoding ((cycles − 8) / 4, floored: libavr's spin granule and per-bit
overhead), so the printed clock is the true one within a granule; --clock
turns it into a stated drift. The autobaud end-to-end asserts the figure
inside exactly that envelope at both clock points.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 01:01:35 +02:00
BlackMark
69f089e53a pureboot 6: a build-time OSCCAL trim, applied ahead of every reset path 
The RC-oscillator answer's device half (dev/tasks.md in libavr): OSCCAL joins
pureboot_add_loader() as one optional byte, written at the top of run() before
the WDRF bail so the watchdog hand-over inherits the corrected clock too.
Orthogonal to the backend — an autobaud build may carry it purely for the
application. No value, no code: the stock image differs from v5 in exactly
the version's two bytes (the stamp and the 'b' immediate).

Measured: +6 B where OSCCAL takes sts (328P, 404→410), +4 B in low I/O
(t85, 402→406); the tightest image in the space (1284 autobaud on USART
pins, 504) carries the sts form at 510 of 512. New gates: the OSCCAL size
points on every chip, the wire-observed trim byte on both addressing
classes (test/pbosccal.py, red-green), and the autobaud unit pinned to
ram_start (test/check_unit.cmake, red-green) — the address --info's
measured-clock read is about to rely on.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 00:53:14 +02:00
BlackMark
fe0d9f8790 build: the submodule is how libavr arrives; the era already carries it 
The pin the whole history now encodes becomes the primary route: the
submodule default replaces FetchContent and the unpinned forge fallback,
LIBAVR_ROOT stays as the tandem-development override, the presets already
take the toolchain file from the submodule, and the Studio projects anchor
their include path there — correct by construction. The version tags and
the one-command historical build are documented beside the version map.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-28 00:28:49 +02:00
BlackMark
3ce817ea03 ide: the Atmel Studio solution master has, on the libavr port 
master carries bootloader.atsln, so main does too. Two projects, because a
.cppproj is one binary at one flag set and this build has hundreds: the stock
328P pureboot loader (USART0 at 115200 on a 16 MHz crystal), and the tsb_asm
tier that occupies the same 512-byte section master's own tsb project targeted.
Both come out byte-identical to the Ninja build — 404 B and 510 B of .text —
in both configurations.

Debug keeps -Os and adds only -gdwarf-4. A loader's section is a correctness
bound, and -Og builds this source to 590 B: the link at 0x7e00 accepts that
without a diagnostic, 78 bytes past flash end, where rcall/rjmp wrap modulo
flash size and the image dies just after activation. Debug info costs no flash,
so the optimisation level stays where correctness needs it.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-27 22:15:28 +02:00
BlackMark
af0dd15a77 tsb: the policy floor, measured and kept 
A fourth tier answering one question: what does the full TinySafeBoot
feature set cost in C++ under pureboot's rules — no assembly, no
register variables, every pureboot lesson applied. 638 bytes, protocol
suite green: 198 below the idiomatic tier, 126 above the 512 B section,
and above the tiers that pay with the banned mechanisms (526 global
registers, 510 with two asm routines). The gap decomposes into the rent
policy-clean C++ pays for state held across calls — push/pop and
argument threading a global-register protocol avoids — and both
control-flow merges tried measured larger than the split cases they
replaced, while the data merge (one send loop over both memories) paid.
The tiers stay; this one keeps the floor an artifact instead of a claim.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-27 18:57:13 +02:00
BlackMark
a54075e526 test: the device runner refuses an image that runs past flash end 
A boot-linked image larger than its slot cannot execute on hardware, and
the naive copy smashed the heap beyond avr->flash — after which the
simulation misbehaved in ways that pointed everywhere but at the size:
phantom byte losses on the UART, garbage in SPMCSR, all downstream of
the overrun. The size gate had said it plainly; now the runner does too.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-27 18:57:13 +02:00
BlackMark
aec430c2e1 docs: name the two data-space regions a poke cannot survive 
Writing 0x60-0x61 on an ATtiny13A reliably garbled the link, which looked like a
loader defect. It is the loader's own footing: .noinit lands at exactly 0x60,
size 2, and on an autobaud build that is unit_ — the measured bit period, and the
whole of its static RAM. Overwrite it and the next reply is timed against
garbage, so the symptom is a mangled prompt byte and no error, because nothing
went wrong except the rate both ends had agreed on.

Identical in kind to poking the stack at the top of SRAM, and cleared by a reset.
test/pbautobaud.py already steered its RAM round-trip clear of the bottom of SRAM
for this reason; only the README had not said it. Both regions are named there
now, beside the note that --poke does reach OSCCAL but that a session survives
only a step or two of moving the clock under itself.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-27 16:48:09 +02:00
BlackMark
9a8a5b0082 tools: measure the images, and hold the README to what is built 
The size matrix proves every image fits its slot and says nothing about the
numbers the README prints. Those drift silently: caller_page() took eight bytes
off every build at once, so all fifteen rows went stale together and no test
noticed, because nothing was over budget. sizes.py check-readme compares the
table against the built images; sizes.py max reports the largest image per chip
and anything over its slot.

It is a check rather than a generator, so the table stays prose someone can
write. No chip geometry lives here either: the image/budget pairs come out of
each build's own CTestTestfile.cmake, which is what the gate checks, so a chip
added or a budget changed needs no edit. Only trees a preset still owns are
read — a stale directory answers with a size that was true once.

16243 images across 37 chips today, none over budget, tightest tsb_asm at 510
of 512.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-27 16:45:20 +02:00
BlackMark
7702c6b700 test: gate autobaud's logic floor, and say what an RC oscillator costs 
The ATtiny13A run left autobaud's low-clock lock looking unreliable: 1/5 at
19200 on a 1.2 MHz RC part. The simulator does not reproduce it. At an exact
clock the calibration is solid down to ~36 cycles a bit and fails outright by
~31 — a sharp edge, not a fraying one — where the real part was already 1 in 5
by ~59. So the effect is the oscillator's own jitter and not backend logic, and
the two floors are different quantities about a factor of two apart.

Both are worth having. pureboot.autobaud gates a tight-bit point, since its two
existing clock points both sat near 100 cycles a bit and would not notice the
floor moving. The README carries the other half: both floors side by side, the
per-clock envelope measured on silicon, and the reason budgeting the logic's ~36
on an RC part is wrong.

It also carries the trap that produced the confusion. On a patched-vector chip an
erased application region walks back up into the loader, so every expired window
opens another and the host's retries eventually catch the pulse — 5/5 where the
same part with an application resident gives 1/5. Measure with an application in
place, or the fixture flatters the backend.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-27 16:44:21 +02:00
BlackMark
77dd45aeca pureboot.py: an update follows the staging copy onto its own link 
--update-loader works by entering copies of the *new* image and letting them
rewrite the resident. Those copies speak the link they were built for, but the
host went on knocking with the session's baud and backend — the resident's. Where
the image changed either, the staging copy was installed and then never answered:
resident untouched, and on a 1 KiB tiny the staging slot is the whole application
region, so the application was already gone.

The wire cannot be probed for it. 512 bytes of position-independent code carry no
header saying what rate they were built for, so the operator declares it:
--staged-baud and --staged-autobaud, applied from the jump into the staging copy
onward. Retuning goes through the open port — SetCommState or tcsetattr on the
live handle, never a reopen — because a DTR pulse would reset the copy being
talked to. Undeclared against a changed link it still cannot work, but the error
now names that as the cause instead of reporting the bare activation timeout that
sent the operator looking at wiring.

The README's idempotence claim needed the same qualification: from step 2 a
re-run must reach the new image, and after step 3 word 0 points at the staging
copy, so on a patched-vector part the resident's link reaches nothing at all.

Found on an ATtiny13A, where two controls differing only in the activation window
updated cleanly and so isolated the link as the variable.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-27 16:31:27 +02:00
BlackMark
433bec3e58 tools: a hardware harness, so a board can be proven and not just a protocol 
check.sh proves the protocol under simavr on every chip; it cannot prove a
board. Two things live only on silicon — an RC oscillator that is not on its
nominal, and a reset edge that has to come from somewhere — and until now the
scripts that reached them were per-session scratch on the machine holding the
programmer, which is where the ATtiny13A run's findings nearly stayed.

pbrig.py is the primitives, knowing nothing per-board: every deployment fact is
a flag or a PUREBOOT_* variable. Two rig facts are encoded in it because neither
is guessable and each cost a session to learn: an ISP access *is* the reset edge
where the adapter's DTR is unwired, so a session begins with an ISP touch and
knocks immediately after; and avrdude splits -U on colons, so a Windows drive
letter breaks the spec and every file goes as a bare name with avrdude run in
its own directory. Its `rate` subcommand is the one that turns "the loader is
silent, so the wiring must be wrong" into a number, by sweeping the host rate
against a fixed cycles-per-bit transmitter — PUREBOOT_HEARTBEAT makes the
existing fixture into one, software link only, since the hardware-link idle owes
the self-update tests its command loop.

pbhw.py takes every bound from the info block the loader reports, so one run
covers a 1 KiB tiny and a 128 KiB mega alike. Both are exercised on an ATtiny13A:
backup verified against a known-good capture, the clock measured at 9.048 MHz
against a 9.6 MHz nominal, and the suite 11/11.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-27 16:06:15 +02:00
BlackMark
e89000f73e pureboot: the pin axis, and the mute it was hiding 
Pins move the image for exactly one reason — a bit-banged link on a USART's own
pins has to release that USART — and the matrix said outright that they were no
axis, so the tightest configuration in the space was one nothing built. Not
subtly, either: the 1284's slot ends at flash end, so that build does not merely
exceed the size test's limit, it fails to link. pureboot_{sw,autobaud}_on_usart
{0,1} are gate points in both matrix modes now, and the exhaustive sweep carries
the pins across its whole cross product. The hand-measured table is the gate's
output: 506 B of 512 for the 1284 autobaud on USART0's pins, 504 on USART1's.

pureboot.mute drives the defect itself — an application hands over with USART0
still enabled and the loader on those pins must still answer. Reaching that
needed the runner to know an enabled USART owns its TxD, which simavr does not
model at all: it wires a USART through IRQs and never takes the pin from the
port. It also brings UCSRnB up with TXEN already set where silicon clears the
register, so the runner restores the reset value for the USART it models — the
mute must come from the application, not from power-on. The fixture stays
silent, since nothing is listening on the USART it brings up.

test_handshake.py, written where no gate could run it, is pureboot.handshake.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
 2026-07-24 22:08:56 +02:00
BlackMark
b0737f7cc0 test: move the handshake regression in beside the rest 
It was written next to the loader source; the harness lives at the repo root.
Not registered with ctest yet — it belongs beside pureboot.planner, which is
the other test of the host tool's pure logic.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-24 18:22:19 +02:00
BlackMark
07f93caba8 pureboot: take the running slot from avr::startup::caller_page 
The write guard's anchor was costing a materialised pointer and a byte swap to
use one byte of it. The libavr primitive answers it in a single load, which is
eight bytes off every build — and what lets the USART release fit the tightest
configuration in the space: the 1284 autobaud on USART-shared pins was 514 of
its 512 and is now 506, with the default pinning down from 510 to 502.

Verified on silicon: the guard still refuses an erase aimed at the slot it runs
from, and still permits one in the application region.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-24 17:57:47 +02:00
BlackMark
45f10f843a pureboot: release a USART left enabled on the software link's pins 
A software or autobaud link on a USART's own pins (PD0/PD1 on the mega328P, so
the Uno's USB bridge reaches it) was mute after an application handed over with
that USART still enabled: its TXEN keeps the USART owning the TX pin, so the
bit-banged transmitter cannot drive it — the loader locked and obeyed commands
but never answered. The link's init now clears the UCSRnB of the USART whose
TXD is its TX pin. Guarded with if constexpr on that pin match, so a link on
non-USART pins emits nothing: +4 bytes on a USART-pin build (494 of 512 for the
mega328P autobaud), zero on the default pb0/pb1 matrix.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-24 17:22:48 +02:00
BlackMark
34b47048ca pureboot.py: bump the tool version to 5 
The drain fix changes the tool's activation behaviour; mark it. The loader
version window is unchanged — the wire protocol did not move.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-24 17:11:03 +02:00
BlackMark
392035923f pureboot.py: bound the activation drain against a flooding target 
The post-prompt settle loop in _handshake had no deadline, so a target that
never falls quiet — a board stuck in a reset loop, whose UART-reset garbage
carries a stray prompt byte — spun the tool forever. Bound it by the handshake
deadline; a real loader still settles on its first quiet read. Regression:
test/test_handshake.py (flood terminates, valid loader still connects).

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-24 17:10:40 +02:00
BlackMark
f98ed406b8 pureboot 5: one command pair for every memory, and a clock-free backend 
R/r/w/F collapse into G and g over a selector byte naming the space — flash,
EEPROM, data, fuse, SPM — with the flash bank in its high nibble. Four command
bodies, four transfer loops and four argument decodes become one of each, and
W joins the same decode instead of keeping an address form of its own. The
loader shrinks while gaining everything below: on the 1284P the stock build
goes 480 -> 432 B and the software one 496 -> 450.

What the freed space buys:

  - Data space. On AVR one pointer spans SRAM, the register file and the whole
    I/O space, so G over space 2 reads all three. pureboot keeps zero static
    RAM and pushes no register, so at loader entry an application's SRAM is
    still what the application left there — this is a post-mortem, not just a
    poke hole. As its own command it needed a dispatch arm and a loop; as one
    more space it is a single ld/st.
  - Host-issued SPM. W fills the page buffer and stops; erase, write and RWW
    re-enable are writes to space 4, which reach the same fused store-and-SPM
    pair through the transfer's own address and data. Any SPM operation, lock
    bits included, is now reachable and the loader carries no page-commit logic.
    The four-cycle SPMCSR-to-SPM window is why that primitive stays fused: no
    host can hit it across a serial link, and that — not the byte count — is
    the floor on how low-level a bootloader's primitives can go.
  - Byte addresses everywhere. The bank in the selector retires the
    word-addressed wire the >64 KiB parts needed, so the 1284s stop being the
    outlier.

SERIAL autobaud is a third backend on the same loader, over libavr's
software_autobaud: no clock, no baud, one binary per chip for every F_CPU and
every rate. Activation counts poll iterations rather than seconds and bounds
every wait, so a stray pulse cannot hold an unattended device.

b answers with the version and signature only; the host derives geometry from
the signature, which is what an autobaud build requires anyway. An update image
is a bare slot with no device to ask, so every image carries a six-byte stamp —
the same bytes b answers with, and the source of both — that the loader never
reads from flash and the host refuses to install a mismatch against. The
running-slot write guard moved onto the SPM commit, which covers erase and
write both where guarding W covered neither directly.

The position-independence lint now proves the property instead of a proxy for
it: the image must come out byte-identical linked at a different base.
-fno-move-loop-invariants left the tuned flag set — it was fitted to a command
loop carrying four transfer bodies and costs bytes now that it carries one.

Verified: the exhaustive matrix on all 37 chips (every clock x every baud x
every backend, non-standard rates included, plus the autobaud build) —
8174 size checks, no failures, tightest fit the 1284s' autobaud at 510 of 512.
Behavioral suites green on every chip class: t13a 10/10, t85 11/11, m8 13/13,
m16a 13/13, m48pa 13/13, 328P 23/23, 644A 17/17, 1284P 17/17. Data-space
round trip through --peek/--poke and the autobaud handshake are both red-green
proven.

The two prototype sources and their findings file go; the README carries the
protocol and dev/done.md in libavr carries the reasoning.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
 2026-07-24 15:50:48 +02:00
BlackMark
a4da885e36 pureboot: the unified autobaud loader, and the hang that settled the decision 
Hardware testing found that a lone calibration pulse wedged the autobaud loader:
run() budgeted only the start-edge wait in measure(), and the rx() that read the
knock behind it was unbudgeted, so one stray low pulse held an unattended device
in the loader and the application never ran. Bound the whole activation — an
expired knock budget returns a byte that cannot be the knock, so control falls
back into the budgeted measure() and an idle line boots the app there.

That fix costs ~22 B, which neither version under review could absorb: the pure
one goes 508 -> 530 on the 1284P and the register one 512 -> 534, both over a
512 B slot. Their margin was never spare capacity, it was the space the missing
fix should have occupied. So the choice between them is moot; both are kept for
the record and no longer built.

pureboot_autobaud_uni.cpp replaces them at 464 B. It is pureboot 5: one read
command and one write command over named spaces (G/g, sel8, addr16, n8) instead
of four per-memory bodies, which collapses four transfer loops into one. The
selector's high nibble carries flash's bank, so the shared cursor stays 16 bits
and no command speaks word addresses. Three things fall out of the freed space:
RAM read/write — the missing feature, and with it arbitrary I/O access, since
AVR maps peripherals into the data space; host-issued SPM, so W's hardcoded
erase/write/RWW tail becomes three writes to a space and any SPM operation is
reachable; and W on the same selector-and-address decode as everything else.

Strictly pure throughout: no inline asm, no global register variable, and no
GPIOR either — the unit lives in a .noinit static, so the loader claims no chip
resource and the chips without GPIOR stop being a special case.

pureboot.py speaks both generations, keyed on the version, so the fixed-baud
path is untouched; --peek/--poke reach the new data space. pbautobaud.py adds a
RAM round-trip and a regression for the hang: a lone pulse must still let the
app boot. All 37 chips plus the 12-preset reflect spot set build and size-test
green, 444-466 B, worst case 46 B under budget. Sim suites 100%: 1284P 17/17,
328P 23/23. Only real-hardware acceptance remains (pureboot/autobaud.md).

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
 2026-07-24 00:48:54 +02:00
BlackMark
335e494a31 pureboot: autobaud host support and simavr end-to-end for both variants 
pureboot.py --autobaud sends the 0xC0 calibration pulse and a single knock at
the host's chosen baud, reads the slimmed info block, and derives the full
geometry from the signature (AUTOBAUD_GEOMETRY, a table over every pureboot
chip). Everything downstream — flash, EEPROM, fuses, hand-over, verify — is the
fixed-baud path unchanged; the dropped write guard is host-transparent.

test/pbautobaud.py drives each variant over the GPIO⇄pty software-UART bridge
through the calibration handshake and a flash + EEPROM + fuse round-trip
cross-checked against the simulator's ground-truth memory, then repeats at
double the F_CPU with the same binary — the clock-agnostic property autobaud
exists for. Wired as pureboot.autobaud_pure/reg on the near-flash 328P and the
word-addressed 1284P. A wrong measured unit fails the flash/verify, so the test
also pins the codegen-coupled calibration constant against a toolchain bump.

Both variants green in sim on both chips at two clocks each; the fixed-baud
suite is unaffected. Only real-hardware acceptance on an RC part remains
(pureboot/autobaud.md).

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-23 22:45:22 +02:00
BlackMark
799709efcf pureboot: autobaud variant, two versions for review 
Measure the host's bit timing at runtime from a 0xC0 calibration pulse, so one
clock-agnostic image per chip runs at any F_CPU — the RC-oscillator deployments
no longer need a per-clock build.

Two source files, differing only in the write-guard/purity tradeoff:
pureboot_autobaud_pure.cpp (the measured unit in the GPIOR I/O scratch
registers, running-slot write guard dropped, 508 B on the 1284) stays strictly
pure; pureboot_autobaud_reg.cpp (unit in one global register variable, guard
kept, 512 B) keeps every feature at the cost of that single GRV. Both fit
512/510 on all 37 chips and share two licensed simplifications: a slimmed info
block (version + signature; the host derives geometry from the chip database)
and a single-byte activation knock.

pureboot/autobaud.md records the decision, the hand-assembly floor (506 B) that
set the target, and the compiler-knob path to it. Size-tested on every chip via
pureboot_add_autobaud(); the fixed-baud loader is untouched. Sim validation, the
host calibration handshake, and real-hardware acceptance remain.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-23 22:15:38 +02:00
BlackMark
7ae80087b3 docs: the watchdog-lockout and EEPROM-wrap gotchas 
A sticky WDRF diverts every reset past the activation window (deliberate, so
an app can reboot instantly, at the cost of a possible lockout); an EEPROM
address past E2END wraps onto low EEPROM (the host bounds it, not the loader).

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-23 02:01:33 +02:00
BlackMark
b477f53ca5 pureboot: the info block reads as a table, one wire byte per line 
clang-format bin-packs braced lists to the column limit, collapsing the
'b' reply's byte layout into dense rows. A minimal clang-format-off span
keeps each wire byte on its own line, where the layout is legible against
the protocol. Whitespace only; image byte-identical.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-23 01:19:09 +02:00
BlackMark
84d3f679c2 style: clang-format the W-fix line 
Layout only, byte-identical output.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-23 01:13:51 +02:00
BlackMark
b5020a1e20 pureboot 4: the loader carries its fixes' identity 
The unaligned-W and U2X-hand-over fixes change the loader's observable
on-wire behavior, and the --stay reconnect fix changes the host tool, so
both move: loader version 3 -> 4, tool VERSION 2 -> 3. The protocol and info
block are unchanged, so OLDEST_LOADER stays 1.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-23 01:09:38 +02:00
BlackMark
1dbf0089d6 pureboot: the info block is what proves a knock landed 
A prompt byte alone does not: one left over from a previous session can
still be in the pipeline while the port opening resets the device into a
fresh window, where the bare command that follows is discarded. Each
attempt is now the whole handshake, retried until the block comes back.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-22 23:49:37 +02:00
BlackMark
39dfe40dbf pureboot: W addresses a page, not a word in it 
The in-page bits of a W address are dropped so the fill always walks from
the page base; the wire contract is one page of data for any address
inside it, on both the byte- and the word-addressed path. +2 B.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-22 23:43:41 +02:00
BlackMark
8470ce3da0 test: the exhaustive clock x baud x backend size matrix 
Every plausible oscillator against every rate it reaches against every
backend, on one chip per size-bearing class, under --full only. The baud
ladder becomes a reachability predicate the enumeration filters on, so an
unreachable point drops out instead of aborting the configure.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-22 23:32:28 +02:00
BlackMark
d634741015 pureboot 3: a 512-byte slot on every chip, the 1284s included 
The word-addressed 1284s were the one family deploying in a 1 KiB slot,
because the far-flash machinery (ELPM reads, RAMPZ page commands, a
word-addressed wire) did not fit 512 B. It does now: 478 B stock, 494 B in
the heaviest configuration the build can produce. They take the 644s'
geometry, where the smallest boot section holds the resident slot and its
staging slot together. The loader's version goes to 3; the host tool did
not change, so its own version stays 2 and only the window it speaks
widens.

Most of the saving is one restructure. The info block and a flash read are
the same act, so giving all four streamed commands one address-and-count
path leaves exactly one call site for the flash streamer: it inlines into
the never-returning command loop and its 24-bit cursor stops being saved
and restored around every transmit. Around it, the ack byte moved out of
line, the wire's byte pair is bit_cast into the word it already is, the
fuse loop ends on its count, the info block's in-slot offset is taken as
the one-byte relocation it is, and -fno-expensive-optimizations gives way
to -fno-move-loop-invariants -fno-tree-ter. Every chip shrank 14-18 B.

The size matrix grew the axes it was missing: the USART1 instance across
the whole clock ladder, and the shape a slow baud gives a software UART —
past 255 delay iterations libavr takes the 16-bit delay loop, which the
ladder default never selects and which was 4 B over the 1284's slot the
first time it was built.

The protocol fixture stopped deriving the loader entry from the flash
size; on the 1284s it had been jumping a slot low and reaching the loader
only because erased flash walked it up.

Docs and comments were consolidated across the port in the same pass: the
README carries a per-chip size table instead of prose, and prose that
restated the code is gone — 190 lines, no behaviour with it.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
 2026-07-22 20:49:23 +02:00
BlackMark
ab842c8d99 pureboot: a version number for the loader, not for the protocol 
The info block's third byte was a protocol version that never moved in the
loader's lifetime. It is the pureboot version now, and this change is
version 2: the one number that says what a deployed loader is. Every loader
already in the field answers 1.

The protocol keeps no number of its own — a pureboot version implies it, and
the host tool is what holds that map. pureboot.py states the loader-version
window it speaks (OLDEST_LOADER/NEWEST_LOADER; a version that changes the
protocol becomes the new floor there), so a loader newer than the tool is
refused by name rather than decoded on the assumption nothing moved, while an
older one is read, identified and installed like any other. The tool carries
its own version, free to drift from the loader's: --version prints it and the
window, --info leads with the device's, --update-loader names the version it
installs.

Tests: the planner unit pins the window — every version in it decodes, one
above it is refused, an older loader's image is still found — and the live
suite pins the built loader against the tool beside it, so a bump that reaches
only one of them fails. The image is byte-identical to the previous build but
for that byte.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
 2026-07-22 17:20:34 +02:00
BlackMark
a58b59c60f docs: correct the size figures for the configured variants 
The headline numbers described the stock deployments but claimed "every
configured variant of them", which the matrix contradicts: choosing the
software UART where the chip has a USART costs 8-46 B, so the megas reach
460-462 rather than 452, and the 1284s' software-serial build is 546 B —
inside their 1 KiB boot sector, but not inside 512.

Also names the actual tightest chip. The 1284 looks like it at 506, but it
deploys in 1 KiB with 478 B spare; against its own budget the ATmega328P
has the least room, 50 B.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-22 17:08:24 +02:00
BlackMark
ceacb61ba1 pureboot: no SPM buffer discard, the host repairs instead 
The temporary page buffer is write-once per word, so a page filled over
one an earlier writer left dirty programs the stale words. The same
datasheet clause carries the cure: the buffer auto-erases after a page
write (§26.2.1; §19.2 on the tinies), so the corruption clears itself by
happening, and rewriting the page programs correctly.

The loader therefore clears the buffer nowhere. The tinies' CTPB and the
m48s' RWWSRE discard are gone; the boot-sectioned megas keep only the
trailing RWWSRE they need anyway to re-enable the RWW section for
read-back, which discards the buffer as a side effect and keeps them off
the path entirely. 434 B on the tiny13s, 438-442 on the tiny25/45/85,
430 on the m48s; the megas are unchanged, the 1284s still 506.

The host takes over the guarantee: a flash page that reads back wrong is
rewritten up to RETRIES times before the run stops. Both read-back paths
repair — verify_pages for programming, and write_differing, which is the
loader-update path where a page left wrong is a half-written loader slot.
That one is not hypothetical: deleting the discard made attiny85
pureboot.rehome fail deterministically there, the only flow still
assuming the old contract.

Protocol-visible, so README's W command says it: one W may program the
wrong bytes after a refused page, or after an application that
self-programmed entered without a reset, and a host that programs without
reading back cannot trust it.

Tests: pureboot.dirty drives the case the loader declines to guard — the
fixture application dirties every buffer word and jumps in with no reset
(hardware forbids that on a boot-sectioned mega, but simavr dispatches SPM
from anywhere, which is what makes it constructible) — and asserts a bare
verify sees the corruption, the repairing verify fixes it in one rewrite,
and it stays fixed. pbreloc asserts the same shape after a refusal.
test_planner covers the bound against a fake device: one bad write
repaired in a single rewrite, a page that never comes good stopping after
exactly three.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-22 16:29:27 +02:00
BlackMark
dd7490a3df build: generated presets and a check entry point 
tools/make_presets.py emits the uniform pipeline the hand-grown file had
drifted from — generated configure/build/test presets and workflows for
all 37 chips, reflect configure/build for libavr's 12-chip spot set —
and tools/check.sh runs every chip's workflow (--full adds the reflect
spot) as the port's gate.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-21 23:42:57 +02:00
BlackMark
bc24b63e65 host: one fact per line, progress bars, --verbose 
--info prints the decoded info block field by field and --fuses each
byte on its own line plus the BOOTSZ/BOOTRST meaning on boot-sectioned
megas. Transfers that take wire time draw a transient progress bar on
stderr when it is a tty — logs, pipes and the tests see only the
summary lines. -v/--verbose narrates decisions: knock counts, the
programming plan, update state handling and per-phase page counts.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-21 23:42:57 +02:00
BlackMark
332b244ac3 pureboot: every deployment axis is a build parameter 
Clock, baud, serial backend (hardware USART 0/1 or the software UART on
any pins) and the activation window all resolve through one CMake
function, pureboot_add_loader() in pureboot/CMakeLists.txt — the unit a
downstream project consumes. The default baud is the fastest standard
rate within 2.5 % (the same best-divisor search libavr's solver runs),
gated on software builds by the polled receiver's 100-cycles-a-bit
floor; every explicit pick is re-checked by the compile's static asserts.

The size matrix builds each axis that can move the image — backend x
clock ladder x USART instance, per chip — against the slot budget, and
two nondefault deployments run the whole protocol suite live: the 328P
on its shipped 1 MHz fuses over software serial on TX=PB1/RX=PB5
(pureboot.custom), and the 644A over USART1 (pureboot.usart1). The sim
runner takes -l to bridge any link, paces a fully quiet bridge toward
real time (a free-running 8 M-cycle window loses the reset-race knock),
and the fixture application speaks the deployment it is built for.

The loader itself shed bytes on the way: the return-address high byte
spelled through byteswap (the double swap folds to the one-byte pick),
the info-block address composed instead of bit_cast, and libavr's new
polled-UART helpers replacing the port's uart::detail reaches. Every
combination fits: 458-506 B across the megas' whole matrix, 470-484 B
on the tinies, 556-562 B in the 1284s' 1 KiB slot.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-21 23:42:57 +02:00
BlackMark
61b687120c pureboot: a loader in the staging slot is the staging copy — leave it there 
The update flow's first step wrote the staging content over whatever the
staging slot held; with a loader running right there (programmed by hand
onto erased flash), that write met the copy's own running-slot guard on
the composed through-word and the tool stopped at its verify — although
the copy is exactly an installed staging copy, able to stream the new
resident like any other. The install is now skipped when the slot holds a
complete loader: its info block where every image carries it, matching
the device's byte for byte, and the slot unchanged since the update began
(the state file's snapshot) — so a resumed half-written install still
differs from its snapshot and takes the install path, which completes it.
pbrehome gains the staging-slot position (an older build at stage
streaming a newer resident in); the README's wrong "cannot re-home from
the staging slot" claim is corrected.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-21 21:55:15 +02:00
BlackMark
ef58d5d363 pureboot: artifact roles, wrong-chip refusal, and misplaced-loader re-homing 
The README's deployment section now says what each build artifact is for:
the .hex is the programmer artifact (self-addressed into the top slot),
the .bin the self-update image — bare slot bytes a programmer would put
at address 0, where a boot-sectioned mega cannot even heal itself (SPM
only runs from the boot section) but a patched-vector chip runs the
position-independent copy and re-homes a build through the ordinary
--update-loader flow: the staging install and the word-0 redirect both
execute outside page 0's slot, so the running-slot guard never blocks it.
pbrehome.py is the acceptance test (misplaced at 0, guard intact,
re-home, app flash over the stale copy, banner); the staging slot is the
one position that cannot re-home itself, documented. The preflight's
wrong-chip refusal and loader_image's handling of padded images (peeled
to the slot content by the embedded base) are documented and the padded
case pinned in the planner.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-21 21:18:10 +02:00
BlackMark
03bb1f56cf pureboot: every libavr chip — 37 loaders, the m48 class, the 644 geometry 
The chip table becomes family blocks covering all 37 targets. The m48s
are a new deployment class: no boot section, so the tiny profile spoken
over the hardware USART — host-patched reset vector, trampoline
hand-over, a 510-byte budget (474 B built), no fuse preflight — while
their RWWSRE store stays the buffer discard (Atmel-8271 §26.2); the
device keys the patch flag and the CPU-halt waits on the curated
boot-section capability and the discard on the RWWSRE bit itself. The
644s' 64 KiB is exactly the 16-bit byte space: plain LPM, byte wire
addresses, 498 B in a 512-byte slot — and their 1 KiB minimum boot
section holds the resident and staging slots together, so self-update
needs no fuse step (the update test's slot pick now keys word-flash on
base >= 64 KiB; base + slot merely touching the boundary stays
byte-addressed). The 1284 joins the 1284P's word-addressed 1 KiB slot at
558 B. BOOT_FUSE gains every boot-sectioned family's ladder and fuse
byte; the planner exercises them all. The sim scaffolding keys
patch-vector-ness instead of the atmega name prefix, the fixture app
picks its clock by family (the tiny25/45/13 builds surfaced the 16 MHz
fallthrough as garbled banners), and the runner's wrapped flash ioctl
performs the m48 discard simavr's no-RWW cores turn into a stray buffer
fill. Sizes across the fleet: 466-504 B megas, 474 B m48s, 498 B 644s,
488-502 B tinies, 558 B 1284s — every chip passing
size/pi/planner/protocol/reloc/update.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-21 18:53:04 +02:00
BlackMark
6a5e313530 pureboot: correct the 1284P deployment profiles in the README 
The deployment section claimed the 1284P has no standalone profile, runs
BOOTSZ = 512 words always, and self-updates with no fuse change, reset
landing at 0x1f800 — internally contradictory (a 512-word section starts
at 0x1fc00, and the section holding both 1 KiB slots is 1024 words) and
contradicted by update_preflight, which refuses a self-update unless the
boot section covers two slots. The text described a 512-byte-slot
geometry this chip's loader cannot have. In truth the 328P profile table
maps onto the 1284P doubled: standalone = 512 words (the smallest
section is exactly the 1 KiB slot, reset at the loader base), self-update
= 1024 words with the loader-first reset walking the staging slot.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-21 16:48:46 +02:00
BlackMark
a28fccf475 pureboot: the 1284P rides a 1 KiB slot — its own boot-sector minimum 
The far machinery (ELPM reads, RAMPZ page commands, wire-word math)
costs ~46 B over the m328P's 504, and the tsb-calibrated C++-to-asm
gap says no implementation of this feature set reaches 512 on this
chip — a boundary its hardware does not have anyway: the 1284P's
smallest boot sector is 1 KiB. The slot therefore becomes
per-geometry (512 B, or 1 KiB past 64 KiB), which the host derives
from the word-addressing flag; slot arithmetic unifies (the index is
the wire high byte with its low bit dropped in either unit), the
update preflight demands a two-slot boot section in the chip's own
terms, and pbapp's hand-back jumps to the real slot base. libavr's
far primitives split their RAMPZ/Z asm operands (a page never
crosses 64 KiB, so callers keep a byte and a 16-bit cursor — the
32-bit address folds away; flash_load_far's byte form becomes the
out-RAMPZ+elpm pair avr-libc's pgm_read_byte_far rebuilds per call),
and the host splits reads at 64 KiB boundaries. All ten chips pass
the full suite — the 1284P at 558 B including protocol, relocation,
and the power-fail self-update — with pureboot byte-identical across
generated and reflect modes everywhere, and the original three
chips' images unchanged to the byte (488/502/504).

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-21 13:54:40 +02:00
BlackMark
92503fbb2d pureboot: the classic megas and the word-addressed 1284P groundwork 
Device: boot-section detection probes SPMCR beside SPMCSR, the link
picks any hardware USART through the instance-aware lookups (URSEL
chips included), WDRF reads MCUSR-or-MCUCSR, and the >64 KiB shape
lands — word-addressed wire flash (info flag bit 1, page byte 0 means
256, base as a word address), far reads through flash_load_far, a
single 32-bit byte-cursor page walk (the 256-byte page wraps its low
byte exactly), and slot arithmetic in words (the return address
already is one). Host: addresses stay bytes internally and scale at
the wire, the boot-fuse decode becomes a per-signature table (byte
index + BOOTSZ ladder — the m168A's lives in EXTENDED), and the
planner tests pin every chip's ladder plus the word-addressed info
decode. Tests: the device runner serves every mega over the USART pty,
pbapp banners over the right link, the update rehearsal synthesizes
its assumed fuses from the tool's own table, and the PI lint tracks
the renamed info symbol. All six classic-mega/168A targets pass the
full suite (size, PI, planner, protocol, reloc, self-update) at
466–504 B; the 1284P builds await a libavr far-path slimming to make
its 512.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-21 12:00:19 +02:00
BlackMark
8ba023ed6b pureboot: take the device signature from the chip database 
libavr now exposes avr::hw::db.signature (compile-time, from the ATDF), so the
info block drops its per-chip hardcoded signature() for the db constant. The
loaders are byte-identical across modes with the correct signature, sizes
unchanged (488/502/504).

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 23:38:20 +02:00
BlackMark
443fd39d31 build: emit a raw .bin beside the HEX for every loader image 
The host tool takes either form — load_image() parses Intel HEX by extension
and treats anything else as raw bytes — but the build emitted only the HEX, so
the raw path had no artifact behind it. The reloc and update tests each shell
out to objcopy at runtime to produce one for themselves.

add_hex_output becomes add_image_outputs and emits both forms. The .bin is
byte-identical to the plain `objcopy -O binary` those tests generate (-R .eeprom
strips nothing the loaders carry), and decodes equal to the HEX payload — 504 B
at 0x7e00 either way for pureboot. Sizes come out at the flash sizes exactly
(504/510/836/526), so nothing stretches to the .data load address.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-20 23:17:59 +02:00
BlackMark
08a0d77109 pureboot: take the emitted loader HEX for --update-loader 
The build emits an Intel HEX beside every loader image, but --update-loader
could not consume one: load_image() anchors every image at address zero, and
a loader HEX links at its base, so it decoded to a 32760-byte blob carrying
504 bytes of loader at the end. staging_content() then refused it as "loader
image is 32760 B, the slot holds 512" - an error naming neither the cause nor
the raw .bin the tool wanted instead.

Drop the blank below the base in the update path. The base comes from the
image's own info block rather than the device's, so an image built for
another target survives the slice intact and the preflight still reports it
as another target rather than failing to find an info block at all.

Verified on an ATmega328P: the full self-update flow driven straight from
pureboot_timeout-5s.hex, resident slot byte-for-byte against the image
afterwards, application preserved; both refusal paths unchanged.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-20 22:46:50 +02:00
BlackMark
260ab2e4e3 pureboot: drive the serial port on Windows too 
The host tool was standard-library-only but POSIX-only with it: termios and
select() bound the port layer, and importing termios failed outright on
Windows, so the module could not even load there.

Split Port into PosixPort (unchanged) and a WindowsPort over the Win32 serial
API through ctypes, picked by os.name; every call site keeps the Port name.
kernel32 only, so the standard-library constraint holds.

Windows has no select() for a COM handle, so the read deadlines move into the
driver as COMMTIMEOUTS, re-armed per read: read_available() ends on a gap
longer than a USB-serial latency timer coalesces (16 ms on FTDI parts),
read_exact() on the count or its deadline. Opening asserts DTR and RTS as a
POSIX open does, so a board wiring DTR to reset still pulses it. A failed
configuration closes the handle before raising - a COM handle is exclusive,
and the leak met the next open as "Access is denied". Win32 takes any integer
baud and a driver may accept one its hardware cannot produce (an FT232R
reports back a baud of 3 and keeps the old divisor), so obvious nonsense is
refused where termios' table would have.

Tested against an ATmega328P on COM6: info, fuses, both memories programmed
and verified, session reconnect, hand-over, the loader self-update, and the
write guard on its own slot. test_planner runs on Windows now as well.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-20 22:46:14 +02:00
BlackMark
e4aaf5bc62 build: emit an Intel-HEX beside every loader image 
avrdude programs Intel-HEX, not ELF, and the build produced only ELFs — so
flashing a loader to a real chip meant running objcopy by hand. add_hex_output()
hangs a POST_BUILD objcopy on each loader image: the three tsb tiers through
add_tsb_variant, pureboot, and the re-timed pureboot9. .eeprom is dropped, being
its own avrdude update.

It uses the toolchain file's CMAKE_OBJCOPY rather than a hardcoded path, so
every chip preset emits hex, not just the mega. pbapp keeps its ELF alone: the
update test converts it to a raw binary itself, and it is not a flashing target.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-20 21:57:26 +02:00
BlackMark
653602058a pureboot: PI lint, tightened gates, and the self-update test suite 
check_pi.py asserts the two link-time facts position independence rests on
(no absolute jmp/call; the info block within the image's first 256 bytes);
the size gates drop to 510 on the tinies for the trampoline word.

New per-chip tests beside the reworked protocol test: the planner units
(programming orders and their recovery properties, the surgery, staging
composition, boot-fuse decode, and the update preflight's error/warning
matrix over synthetic fuse bytes), the relocated-copy sweep (the identical
image installed one slot lower serves the full command set — the PI
acceptance test, and the one that caught the temporary-buffer trap), and
the self-update end-to-end: --update-loader to a re-timed build
(pureboot9, byte-different by PUREBOOT_TIMEOUT alone), then every
power-fail phase killed mid-write, restarted from the runner's flash dump,
and completed by a re-run with the application intact throughout. The mega
rounds run the BOOTRST-unprogrammed profile: the fixture application's 'L'
jump is the application-owned loader entry that profile relies on.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 19:37:57 +02:00
BlackMark
57d1c009cc pureboot: one position-independent binary — its own staging loader 
The image now runs from any 512-byte slot with every command intact:
control flow stays PC-relative, the write guard keys on the running slot
(the return-address anchor, computed once), the info block is addressed
from that same anchor as a byte pair (no absolute 16-bit address in the
image), and the application jump is an indirect call through a noipa-
laundered pointer to the absolute entry. 'J' — jump to a wire word
address, the one transfer primitive — replaces 'G': the host knows the
application entry from the info block, and moving between loader copies
needs arbitrary targets. The activation window is a compile-time 8 s
(PUREBOOT_TIMEOUT overrides), counted as a single calibrated poll loop.

A refused page no longer poisons the write-once temporary buffer (a real
silicon trap: the next write would program the drained data): every page
write discards the buffer first — CTPB on the tinies, on the mega the same
RWWSRE store that re-enables RWW after programming. The tinies' post-op
busy-waits go with it: their CPU halts through page erase and write.

488 / 502 / 504 B on t13a / t85 / mega — under the tinies' 510-byte budget,
whose last slot word is the host-managed trampoline: the resident's holds
the application entry, a staging copy's the jump through which an abandoned
update still times out into a loader.

The host tool updates the loader with itself: --update-loader installs the
identical image one slot below the resident, jumps into it, lets it rewrite
the resident, and restores the staging region from a state file — each
phase idempotent off the flash state, resumable after any interruption
(t13a: the staging slot carries the reset vector, written last in and
first out; t85: word 0 redirected around the resident rewrite; mega:
fuse-matrix preflight with a hard BOOTSZ gate and --assume-fuses for
simulators). Application flashing recovers by reset from any interruption:
patched page 0 and trampoline first, erase descending, and a walk-region
refusal behind --force on BOOTRST-below-loader megas.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 19:37:43 +02:00
BlackMark
06bb06d994 pureboot: harden the sim device runner 
Cancel the GPIO bridge's cycle timers with the state they drive: avr_reset
drops the TX latch, whose falling edge starts a spurious decode before
bridge_reset runs, and the stale sampler then interleaves with the loader's
first real answer through the shared shift state — the first post-reset
replies came back corrupted and the knock retries burned the activation
window into the application.

Wrap the mega's registered flash ioctl to re-dispatch page erases with Z
masked to the page boundary: simavr's PGERS handler erases spm_pagesize
bytes from Z & ~1 (its PGWRT path masks correctly), wiping the neighbouring
page when Z sits past the page start, which hardware permits (§26.8.1).
Model the write-once temporary buffer in the tiny NVM module — silicon
refuses a second load per word until the buffer clears, and a last-write-
wins model masks real firmware bugs.

Optional arguments select the reset vector (the mega's fuse profiles) and a
raw flash image to resume from (power-fail tests re-enter a dumped state).

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 19:37:10 +02:00
BlackMark
9a9a7ef0e8 pureboot: review-pass fixes to the host tool and device runner 
pureboot.py: reject an empty image file with a clear error instead of
an IndexError deep in the vector-surgery planner; tighten the erase
docstring (order is irrelevant there — every target byte is the same
value, unlike a real flash where page 0 must go last).

pureboot_device.c: the GPIO bridge's bit_cycles used plain truncating
division where the firmware computes its own bit period with
round-to-nearest (uart.hpp: (Clock.hz + Baud.bd/2)/Baud.bd) — one
cycle off per bit on both tinies, harmless in practice but needless
drift against a firmware built to a different constant. Matched
exactly. Also clear the queued-bytes/decode-in-progress bridge state
on the test-only reset signal, so a future reset-mid-transfer scenario
can't feed a freshly reset chip bytes queued for its previous life.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 10:45:19 +02:00
BlackMark
4acf358dda pureboot: gitignore python bytecode cache 
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 10:43:56 +02:00
BlackMark
11c10f986d pureboot: stop tracking the python bytecode cache 
A stray __pycache__/*.pyc from a local test run got swept into the
previous commit's git add. Untracked and gitignored.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 10:43:36 +02:00
BlackMark
f587f0a26e pureboot: host tool and end-to-end protocol tests, all three chips 
pureboot.py (Python stdlib only): images as raw binary or Intel HEX,
flash and EEPROM programming with read-back verify, erase composites,
fuse and info readout, activation-timeout configuration, and the
tinies' reset-vector surgery — the trampoline word below the loader,
page 0 written last.

The test spawns a simavr device (pureboot_device.c) — the mega's USART
as a pty; on the tinies a cycle-timed GPIO<->pty bridge for the polled
software UART plus the NVM module simavr's tiny cores lack (their SPM
opcode ioctls into a void and silently does nothing) — and drives it
with the real tool: knock from reset (erased-flash walk on the tinies),
program and verify both memories, timeout write, session reconnect, an
external reset through the patched vector, hand-over, and the fixture
application's banner. Results are cross-checked against ground-truth
memory dumps and an independent decode of the surgery's rjmp words,
red-verified against a sabotaged encoder.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 05:54:15 +02:00
BlackMark
27c768a102 pureboot: the device — one pure C++ source, 512 bytes, every chip 
No inline assembly, no global register variables; libavr does the
datasheet work. The device speaks primitives — flash read/page-program,
EEPROM read/write, fuse read, info block, EEPROM-resident activation
timeout, hand-over — and verify, erase, reset-vector surgery, and
timeout configuration live in the host tool. 490 B on the ATtiny13A,
510 B on the ATtiny85, 484 B on the ATmega328P, each linked into the
top 512 bytes of flash; per-chip size tests gate all three.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 05:33:28 +02:00
BlackMark
d989b5b8cd tsb: third size pass — restructure to the oracle's shape 
The second pass concluded the 168 B tricks->asm gap was per-call ABI
cost. Most of it was structure. Rebuilt around the oracle's own shape —
argless noinline primitives over a whole-loader call-saved register
protocol (g_addr in Y, count r16, window r7, direction latch r6), a
top-down erase_below whose loop tests against zero and hands callers
g_addr = 0 for free, bounded rx everywhere (a silent host unwinds to
the app from any state, as the oracle does), and a named tsb_app entry
that --pmem-wrap-around=32k relaxes to the wrapped rjmp:

  tsb_asm    510 B in the 512 B section (oracle: 500), C++ except rx
             and the page-store loop — the two routines whose remaining
             cost is the calling convention itself (~30 asm lines, was
             ~280)
  tsb_tricks 526 B, no assembly at all (was 666)
  tsb_pure   836 B, still one readable function per command (was 842)

Every g_* update placement works around a GCC 16.1 wrong-code bug
(stores into global register variables deleted when only callees read
them — repro and rules in libavr dev/lessons.md). Also fixes two
latent hardware bugs all earlier tiers carried, masked by simavr's
zeroed register file: the crt-less entries never established
__zero_reg__ = 0, and the direction latch was read before written —
power-on registers are undefined.

All tiers full oracle feature parity, protocol tests green in both
libavr modes, .text byte-identical across modes.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
 2026-07-20 01:00:27 +02:00
BlackMark
314e422b19 tsb: beat the first-pass size floors (tricks 666, pure 842) 
tricks 778->666: always_inline every single-call handler into the
[[noreturn]] reset entry (which pays no prologue, so their push/pop of
call-saved registers vanishes), walk the page pointer in Y (adiw, base
recovered as g_addr-page) instead of recomputing Z=base+offset, bring
the UART up in the two registers that are not already at their reset
value, and seed the activation counter as __uint24.

pure 896->842: TU-local internal linkage (proper hygiene, and it lets
the compiler inline the one-call handlers), a byte-wide activation
count, __uint24 timeout. Still one readable function per command.

asm unchanged at 498: its C++-expressible parts are already C++; the
core stays asm (the 666 B all-tricks tier is 168 B over — per-call ABI
tax, not a feature). All three cross-mode byte-identical, protocol green.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-19 20:15:49 +02:00
BlackMark
3e0717ef06 tsb: drive each tier to its size floor 
asm 502->498 B (below the oracle's 500): the stack bring-up moves to plain C++,
and a register is reserved for the config-page high byte instead of reloading it
at each app-flash-boundary compare. tricks 808->778 B: shared erase/rww helpers
plus the libavr half-duplex W1C fix. pure 950->896 B and no SRAM: streams
rx->SPM/EEPROM instead of staging a 128 B page buffer. All three keep full oracle
feature parity and stay byte-identical across modes; protocol tests (round-trip +
password + emergency erase) green.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-19 18:47:38 +02:00
BlackMark
812be910c1 tsb: document the three tiers at full parity in the build file 
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-19 16:50:18 +02:00
BlackMark
34529c8031 tsb: protocol test covers the password gate and emergency erase 
Each scenario group now runs on its own freshly-reset device: the round-trip
on a blank config page, plus a password-config device that must be sent the
password after the knock to activate, and an emergency-erase device where a
0-byte + two confirms wipes flash, EEPROM and the config page (verified by
reading all three back as 0xff). All three tiers pass every group.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-19 16:49:20 +02:00
BlackMark
06bd56af50 tsb: pure and tricks tiers reach full oracle feature parity 
Both tiers gain the features the asm tier already carries — one-wire
half-duplex (via libavr's new .half_duplex), the config-page activation
timeout, and emergency erase (password \0 + double-confirm wipes flash,
EEPROM and the config page) — on top of the watchdog bail, password gate and
config/flash/EEPROM read-write they already had. pure stays idiomatic
(flash_table info block, one function per command) at 950 B; tricks keeps its
compiler trickery (call-saved global-register page walk, unified runtime-flag
paths pinned noinline/noclone, streaming stores, arithmetic command decode)
at 808 B. Both byte-identical across generated and reflect modes; the size
gradient across the three tiers is now 502 / 808 / 950 B.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-19 16:47:21 +02:00
BlackMark
75bb84fa3e tsb: asm tier reaches full oracle feature parity at 502 B 
Rewrite the inline-asm tier so it matches the hand-written fixed-baud oracle's
feature set inside the 512 B boot section: watchdog-reset bail, one-wire
half-duplex (RXEN/TXEN toggled per direction, TX turnaround guard),
config-page activation timeout, the password gate (wrong byte hangs draining
the UART), emergency erase (password \0 + double-confirm wipes flash, EEPROM
and the config page), and config/flash/EEPROM read-write. Every geometry,
baud and info-block constant comes from libavr consteval; only the dense
control flow is hand-written. 502 B, byte-identical across generated and
reflect modes.

Test harness: seed the config page from TSB_CONFIG so the password and
emergency-erase paths are exercisable, and clear simavr's AVR_UART_FLAG_POLL_
SLEEP — a host-CPU-saving usleep(1)-per-idle-poll hack that models no hardware
and paces a one-wire loader (which releases TX between bytes) in real time,
distorting protocol timing.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-19 16:23:16 +02:00
BlackMark
778b8a0100 tsb: vendor the fixed-baud assembly oracle as the size/feature bar 
The Seed Robotics native-UART fixed-baud TinySafeBoot (GPLv3), reference
only — not built. Assembles to 500 B with the full feature set, proving
≤512 B and full feature parity are simultaneously reachable. Also drops the
stale empty stk500v2/ leftover.

Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
 2026-07-19 15:29:58 +02:00
BlackMark
48d11fe8e3 tsb: use the named register surface 
Direct register access now reads through the named surface
(hw::mcusr::wdrf.test(), hw::ucsr0b::write(...)) instead of the string form,
matching how libavr itself is written. Zero-overhead: pure 740 B, tricks 658 B,
asm 508 B unchanged, all byte-identical across modes, protocol green.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
 2026-07-19 14:55:01 +02:00
BlackMark
bb4784ae0c tsb: refactor the pure tier onto libavr sugar 
The showcase tier now leans on the helpers it fed back instead of reaching under
them: the info block is an avr::flash_table (no raw [[gnu::progmem]]), a page is
filled with spm::fill(addr, span) (no hand-packed lo|hi<<8 loop), and the
WDT-reset bail reads field<"MCUSR","WDRF">::test() (no read() & {}(1).value).

Zero-overhead throughout: .text stays 740 B, byte-identical across generated and
reflect modes, protocol test green. The info block streams through the existing
address-based send_flash rather than a range-for over the flash_table — the
range-for is a distinct loop that cannot share the loader's one flash streamer,
so it would add 14 B for no functional gain.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
 2026-07-19 13:33:53 +02:00
BlackMark
d07586652d tsb: slim the port branch to the libavr reimplementation 
main carried the whole pre-libavr tree beside the port: the other-bootloader
directories (blink, stk500v2), the Atmel Studio solution/project, and — dead in
the tsb dir itself — four submodule links to the superseded io/flash/uart/type
libraries the libavr sources never include. None are build inputs; CMake drives
the three variants through FetchContent. master keeps the full legacy tree
untouched.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
 2026-07-19 13:12:56 +02:00
BlackMark
3a2f2a23c2 tsb: drop the local -O3 strip, now handled by the libavr toolchain 
The -O3 leak is fixed upstream (cmake/release-os.cmake via CMAKE_PROJECT_INCLUDE),
so the port no longer needs its own string(REPLACE); a Release build is -Os
through the toolchain file. Verified: all three variants build at their sizes
(508/658/740) and pass the size + protocol ctest.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
 2026-07-19 10:52:13 +02:00
BlackMark
4fa058653e tsb: reimplement TinySafeBoot on libavr in three size tiers 
The native-UART fixed-baud TinySafeBoot protocol, ported onto libavr as a
crt-free boot-section loader, in three variants that trade clarity for size:

  tsb_pure   740 B  idiomatic C++: SRAM page buffer, separate flash/EEPROM
                    leaves, shared framing; the polled `unused` guard posture.
  tsb_tricks 658 B  unified runtime-flag paths (noinline/noclone), call-saved
                    global-register page walk — attributes only, no asm.
  tsb_asm    508 B  streaming store + hand-rolled UART/SPM/EEPROM/erase loops;
                    fits the 512 B boot section (BOOTSZ=11). Trims the optional
                    password gate and WDT-reset bail — unreachable in C++ with
                    both (hand-asm is ~15 % denser). Tiers 1-2 keep them and
                    live in the 1 KB section they fit.

All three are .text byte-identical across libavr's generated and reflect modes.
The CMake build strips the leaked -O3 (a Release build is silently -O3, not the
-Os this loader is measured against) and gates each variant's size against its
section. A simavr harness (test/device.c + test/tsbtest.py) drives the real wire
protocol over a pty and flashes the device; the size and protocol tests run in
ctest. Verified byte-for-byte against the reference tsbloader_adv (C#/mono):
activate, read info, flash write + verify.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
 2026-07-19 05:00:51 +02:00
69 changed files with 12866 additions and 2187 deletions
Expand all files Collapse all files

1
.clang-format
View File

@@ -1,5 +1,6 @@
---
BasedOnStyle: LLVM
Standard: Latest
ColumnLimit: 120
IndentWidth: 4
TabWidth: 4

9
.gitignore vendored
View File

@@ -9,3 +9,12 @@ Debug
*.eeprom
*.lss
*.map
# CMake / clangd
/build/
compile_commands.json
.cache/
# Python
__pycache__/
*.pyc

30
.gitmodules vendored
View File

@@ -1,27 +1,3 @@
[submodule "tsb/io"]
path = tsb/io
url = git@git.blackmark.me:avr/io.git
[submodule "tsb/flash"]
path = tsb/flash
url = git@git.blackmark.me:avr/flash.git
[submodule "tsb/uart"]
path = tsb/uart
url = git@git.blackmark.me:avr/uart.git
[submodule "tsb/type"]
path = tsb/type
url = git@git.blackmark.me:avr/type.git
[submodule "stk500v2/type"]
path = stk500v2/type
url = git@git.blackmark.me:avr/type.git
[submodule "stk500v2/io"]
path = stk500v2/io
url = git@git.blackmark.me:avr/io.git
[submodule "stk500v2/uart"]
path = stk500v2/uart
url = git@git.blackmark.me:avr/uart.git
[submodule "stk500v2/flash"]
path = stk500v2/flash
url = git@git.blackmark.me:avr/flash.git
[submodule "blink/io"]
path = blink/io
url = git@git.blackmark.me:avr/io.git
[submodule "libavr"]
path = libavr
url = ../libavr.git

714
CMakeLists.txt Normal file
View File

@@ -0,0 +1,714 @@
cmake_minimum_required(VERSION 3.28)
project(tsb_libavr LANGUAGES CXX)
# libavr rides as the pinned submodule; LIBAVR_ROOT (cache or environment)
# overrides it for tandem development against a working tree. The toolchain
# file comes from the submodule via CMakePresets.json either way.
if(NOT LIBAVR_ROOT AND DEFINED ENV{LIBAVR_ROOT})
set(LIBAVR_ROOT $ENV{LIBAVR_ROOT})
endif()
if(NOT LIBAVR_ROOT)
set(LIBAVR_ROOT ${CMAKE_CURRENT_SOURCE_DIR}/libavr)
endif()
if(NOT EXISTS ${LIBAVR_ROOT}/CMakeLists.txt)
message(FATAL_ERROR "libavr not found at ${LIBAVR_ROOT} — run: git submodule update --init libavr")
endif()
add_subdirectory(${LIBAVR_ROOT} libavr-build)
if(PROJECT_IS_TOP_LEVEL)
add_compile_options(-Werror) # warnings are errors for the port's own code
enable_testing()
# The behavioral tests drive the real wire protocols over a simavr pty
# (as the host tools do) and actually flash the device. The runners are
# host programs built at configure time against libsimavr (C++23 — what
# the distribution's compiler speaks in full); if they or Python are
# missing, only the size tests run.
find_program(_host_cxx NAMES c++ g++)
find_package(Python3 COMPONENTS Interpreter)
if(_host_cxx AND Python3_FOUND)
set(PB_DEVICE ${CMAKE_BINARY_DIR}/pureboot_device)
execute_process(
COMMAND ${_host_cxx} -std=c++23 -Wall -Wextra -O2
-I/usr/include/simavr -I/usr/include/simavr/parts
-o ${PB_DEVICE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pureboot_device.cpp
-lsimavr -lsimavrparts -lelf -lutil
RESULT_VARIABLE _pbdev_res ERROR_VARIABLE _pbdev_err)
if(NOT _pbdev_res EQUAL 0)
message(STATUS "pureboot_device not built (${_pbdev_err}) — protocol tests skipped")
unset(PB_DEVICE)
endif()
if(LIBAVR_MCU STREQUAL "atmega328p")
set(TSB_DEVICE ${CMAKE_BINARY_DIR}/tsb_device)
execute_process(
COMMAND ${_host_cxx} -std=c++23 -Wall -Wextra -O2
-I/usr/include/simavr -I/usr/include/simavr/parts
-o ${TSB_DEVICE} ${CMAKE_CURRENT_SOURCE_DIR}/test/device.cpp
-lsimavr -lsimavrparts -lelf
RESULT_VARIABLE _dev_res ERROR_VARIABLE _dev_err)
if(NOT _dev_res EQUAL 0)
message(STATUS "tsb_device not built (${_dev_err}) — protocol tests skipped")
unset(TSB_DEVICE)
endif()
endif()
endif()
endif()
# The ELF is only a container (symbols, section headers) and is never flashed —
# and the host tool's load_image() dispatches on extension, so handing it one
# would silently program the header bytes. Every loader image therefore gets
# both flashable forms beside it at link time: .hex for avrdude, and .bin for
# the host tool's raw path (which is what the reloc and update tests convert to
# on the fly). .eeprom is dropped — EEPROM content is its own update.
function(add_image_outputs name)
add_custom_command(TARGET ${name} POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O ihex -R .eeprom
$<TARGET_FILE:${name}> $<TARGET_FILE:${name}>.hex
COMMAND ${CMAKE_OBJCOPY} -O binary -R .eeprom
$<TARGET_FILE:${name}> $<TARGET_FILE:${name}>.bin)
endfunction()
# The TinySafeBoot protocol reimplemented on libavr in variants that trade
# clarity for size. Each links into the ATmega328P boot section (BOOTSZ selects
# its size; BOOTRST vectors a reset to its base) with -nostartfiles — a polled
# loader has no use for the crt or the vector table. The entry sits in
# .vectors, laid first, and runs — avr::startup::entry on the policy tier,
# the experiment tiers' own naked stubs elsewhere, each documented in its
# source. The boot base is FLASHEND+1 minus the section size; the linker
# section-start and the source's boot_bytes agree. tsb_app is
# the application's reset vector, pinned to 0 here so the loaders jump to a
# named function; --pmem-wrap-around lets relaxation turn that absolute jump
# into the wrapped rjmp AVR's modulo-flash PC actually executes.
# All four implement the full oracle feature set (see oracle/README.md):
# watchdog bail, one-wire half-duplex, config-page activation timeout, password
# gate, emergency erase, config/flash/EEPROM read-write. They differ only in how,
# and the size gradient is the cost of that "how" — see dev/lessons.md.
# tsb_asm — the tricks tier's C++ with exactly two routines in asm (the
# bounded rx and the page-store loop — the two whose remaining
# cost is the C ABI itself): 510 B in the 512 B section the
# hand-written 500 B oracle occupies. Everything else, from
# bring-up to dispatch, is C++ on libavr.
# tsb_tricks — no asm at all: the whole-loader register allocation lives in
# global register variables (Y walks the page pointer), every
# helper is a tiny noinline primitive placed by the
# global-register store rules, pages stream straight to
# SPM/EEPROM, and the bring-up is the two reset-non-default
# registers only. 526 B in the 1 KB section (BOOTSZ=10) — 14
# over the oracle's section, from 168 over at this tier's first
# floor.
# tsb_pure — pure idiomatic libavr, one function per command, TU-local
# (internal linkage), streaming (no SRAM page buffer): 836 B in
# the 1 KB section.
# tsb_policy — the policy floor: pureboot's rules (no asm, no register
# variables) with every pureboot lesson applied. 638 B in the
# 1 KB section — the measured evidence that the 512 B fit is a
# property of the mechanisms philosophy #5 bans.
#
# add_tsb_variant(<name> <boot-section-bytes>)
function(add_tsb_variant name bytes)
math(EXPR base_dec "32768 - ${bytes}")
math(EXPR base_hex "${base_dec}" OUTPUT_FORMAT HEXADECIMAL)
add_executable(${name} tsb/${name}.cpp)
target_link_libraries(${name} PRIVATE libavr)
target_link_options(${name} PRIVATE -nostartfiles -Wl,--section-start=.text=${base_hex}
-Wl,--defsym=tsb_app=0 -Wl,--pmem-wrap-around=32k)
add_custom_command(TARGET ${name} POST_BUILD COMMAND ${CMAKE_SIZE} $<TARGET_FILE:${name}>)
add_image_outputs(${name})
if(PROJECT_IS_TOP_LEVEL)
add_test(NAME ${name}.size
COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:${name}>
-DLIMIT=${bytes} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
if(DEFINED TSB_DEVICE)
add_test(NAME ${name}.protocol
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/tsbtest.py
${TSB_DEVICE} $<TARGET_FILE:${name}> ${base_hex})
endif()
endif()
endfunction()
# The tsb tiers reimplement the ATmega328P-only reference protocol; the other
# chips build pureboot alone.
if(LIBAVR_MCU STREQUAL "atmega328p")
add_tsb_variant(tsb_asm 512)
add_tsb_variant(tsb_policy 1024)
add_tsb_variant(tsb_pure 1024)
add_tsb_variant(tsb_tricks 1024)
# The policy tier's floor is measured with the loop flags pureboot's size
# work found (a loader's loop bodies all contain calls); the other tiers
# keep the flag set their recorded floors were measured with — none.
target_compile_options(tsb_policy PRIVATE -fno-move-loop-invariants -fno-tree-ter)
endif()
# pureboot — the pure-constraint port (see pureboot/README.md): one source,
# no inline assembly, no global register variables, every libavr chip,
# fitting each chip's smallest boot sector. The geometry and the
# pureboot_add_loader() deployment function live in pureboot/CMakeLists.txt —
# the unit a downstream project consumes; everything below is this port's
# own build: the stock loaders, their tests, and the size matrix. The
# distinct binary dir keeps the `pureboot` target's output name free.
add_subdirectory(pureboot pureboot-cmake)
# The stock loader: the family-default deployment (crystal/RC clock, the
# chip's natural link, default pins). The activation window stays a cache
# variable — re-timing a deployed loader is a self-update with a re-timed
# build. pureboot9 is that re-timed build, and what the update test installs.
set(PUREBOOT_TIMEOUT 8 CACHE STRING "pureboot activation window, seconds")
pureboot_add_loader(pureboot TIMEOUT ${PUREBOOT_TIMEOUT})
if(PROJECT_IS_TOP_LEVEL)
get_target_property(_pb_stock_hz pureboot PUREBOOT_HZ)
get_target_property(_pb_stock_baud pureboot PUREBOOT_BAUD)
add_test(NAME pureboot.size
COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:pureboot>
-DLIMIT=${PUREBOOT_LIMIT} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
if(Python3_FOUND)
add_test(NAME pureboot.pi
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/check_pi.py
${CMAKE_OBJDUMP} ${CMAKE_OBJCOPY} ${CMAKE_CXX_COMPILER} ${LIBAVR_MCU}
$<TARGET_FILE:pureboot>
${CMAKE_BINARY_DIR}/CMakeFiles/pureboot.dir/pureboot/pureboot.cpp.obj
${PUREBOOT_BASE_HEX})
add_test(NAME pureboot.planner
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/test_planner.py
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py)
add_test(NAME pureboot.scan
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/test_scan.py
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py)
# CMakePresets.json is generated; hand edits drift the moment the
# generator reruns, so the gate holds the pair together.
add_test(NAME presets.generated
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/tools/make_presets.py
--check)
add_test(NAME pureboot.handshake
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/test_handshake.py)
add_test(NAME pureboot.updatelink
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/test_update_link.py)
endif()
# The protocol test flashes this fixture through the loader with the real
# host tool and expects its banner after the hand-over; a normally linked
# application whose reset vector is what the tinies' surgery re-homes.
if(DEFINED PB_DEVICE)
add_executable(pbapp test/pbapp.cpp)
target_link_libraries(pbapp PRIVATE libavr)
add_custom_command(TARGET pbapp POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary $<TARGET_FILE:pbapp> $<TARGET_FILE:pbapp>.bin)
add_test(NAME pureboot.protocol
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
${PB_DEVICE} $<TARGET_FILE:pureboot> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud} ${PUREBOOT_EEPROM}
$<TARGET_FILE:pbapp>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbtest-work)
set_tests_properties(pureboot.protocol PROPERTIES TIMEOUT 180)
# The activation window as a measured duration: application installed,
# line idle, the first transmit is the application's banner — its
# cycle is the window the source declares, held to ±2 % (one
# mis-counted cycle per poll is a 10 % shift).
add_test(NAME pureboot.window
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbwindow.py
--device ${PB_DEVICE} --loader $<TARGET_FILE:pureboot>
--mcu ${PUREBOOT_SIM_MCU} --hz ${_pb_stock_hz}
--base ${PUREBOOT_BASE_HEX} --page ${PUREBOOT_PAGE}
--baud ${_pb_stock_baud} --app $<TARGET_FILE:pbapp>.bin
--seconds ${PUREBOOT_TIMEOUT}
--tool ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
--workdir ${CMAKE_BINARY_DIR}/pbwindow-work)
set_tests_properties(pureboot.window PROPERTIES TIMEOUT 300)
# The half-duplex loader's window, same gate: its poll runs through
# rx_ready()'s release-line test, whose outlined call re-shapes the
# whole loop — a per-class cycle count (poll_cost() in pureboot.cpp)
# that only the built image can prove, chip by chip.
if(PUREBOOT_HAS_USART)
add_test(NAME pureboot.window.halfduplex
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbwindow.py
--device ${PB_DEVICE} --loader $<TARGET_FILE:pureboot_hd>
--mcu ${PUREBOOT_SIM_MCU} --hz ${_pb_stock_hz}
--base ${PUREBOOT_BASE_HEX} --page ${PUREBOOT_PAGE}
--baud ${_pb_stock_baud} --app $<TARGET_FILE:pbapp>.bin
--seconds ${PUREBOOT_TIMEOUT}
--tool ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
--workdir ${CMAKE_BINARY_DIR}/pbwindow-hd-work)
set_tests_properties(pureboot.window.halfduplex PROPERTIES TIMEOUT 300)
endif()
# The position-independence acceptance test: the identical image,
# installed one slot lower, must serve the full command set.
add_test(NAME pureboot.reloc
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbreloc.py
${PB_DEVICE} $<TARGET_FILE:pureboot> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud}
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbreloc-work)
set_tests_properties(pureboot.reloc PROPERTIES TIMEOUT 180
ENVIRONMENT "PB_OBJCOPY=${CMAKE_OBJCOPY}")
# Entering the loader from a running application with no reset
# between, over a page buffer the application dirtied — the case the
# loader declines to guard and the host repairs. Hardware forbids the
# state here (SPM runs only from the boot section); simavr does not,
# which is what makes it constructible.
if(LIBAVR_MCU STREQUAL "atmega328p")
add_test(NAME pureboot.dirty
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbdirty.py
${PB_DEVICE} $<TARGET_FILE:pureboot> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud}
$<TARGET_FILE:pbapp>.bin
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbdirty-work)
set_tests_properties(pureboot.dirty PROPERTIES TIMEOUT 180)
endif()
# Re-homing: a loader mistakenly programmed at address 0 (a raw .bin
# handed to a programmer) or sitting in the staging slot must heal
# into the canonical slot through the ordinary --update-loader flow.
# Patched-vector behavior, so one representative chip carries it.
if(LIBAVR_MCU STREQUAL "attiny85")
add_test(NAME pureboot.rehome
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbrehome.py
${PB_DEVICE} $<TARGET_FILE:pureboot> $<TARGET_FILE:pureboot9>.bin
${PUREBOOT_SIM_MCU} ${_pb_stock_hz} ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE}
${_pb_stock_baud} $<TARGET_FILE:pbapp>.bin
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbrehome-work)
set_tests_properties(pureboot.rehome PROPERTIES TIMEOUT 180)
endif()
# The self-update end-to-end: the re-timed build (same source, only
# the timeout differs — a byte-different image) replaces the resident
# through --update-loader, with every power-fail phase rehearsed from
# the runner's flash dumps.
pureboot_add_loader(pureboot9 TIMEOUT 9)
add_test(NAME pureboot.update
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbupdate.py
${PB_DEVICE} $<TARGET_FILE:pureboot> $<TARGET_FILE:pureboot9>
${PUREBOOT_SIM_MCU} ${_pb_stock_hz} ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE}
${_pb_stock_baud} $<TARGET_FILE:pbapp>.bin
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbupdate-work)
set_tests_properties(pureboot.update PROPERTIES TIMEOUT 600
ENVIRONMENT "PB_OBJCOPY=${CMAKE_OBJCOPY}")
endif()
# The size matrix: every configuration axis that could move the image
# size — the serial backend (different code), the USART instance
# (different registers), the clock (different constants), the baud
# through the shapes its bit timing takes, and the pins through the one
# thing they decide (whether a bit-banged link has to release the USART
# that owns them) — each combination must still fit the chip's slot
# budget. The timeout is a constant and adds no axis. The stock build is
# one point of this matrix and already has its test.
function(pureboot_size_variant name)
pureboot_add_loader(${name} ${ARGN})
add_test(NAME ${name}.size
COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:${name}>
-DLIMIT=${PUREBOOT_LIMIT} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
endfunction()
# The autobaud loader: one clock-agnostic image per chip, so it has no
# clock x baud axis of its own — the matrix below sweeps those for the
# fixed-baud builds, and this one binary has to serve all of them at run
# time. Size-tested against the same per-chip budget as every other variant.
pureboot_add_loader(pureboot_autobaud SERIAL autobaud)
add_test(NAME pureboot_autobaud.size
COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:pureboot_autobaud>
-DLIMIT=${PUREBOOT_LIMIT} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
# The measured unit's home is wire contract, not layout accident: the
# host reads the bit period from it (--info's measured clock). In the
# GPIOR home the image must carry no RAM copy at all; in the RAM home it
# is the loader's only RAM object, at the very start of SRAM.
add_test(NAME pureboot_autobaud.unit
COMMAND ${CMAKE_COMMAND} -DOBJDUMP=${CMAKE_OBJDUMP} -DELF=$<TARGET_FILE:pureboot_autobaud>
-DRAM_START=${PUREBOOT_RAM_START} -DGPIOR=${PUREBOOT_UNIT_GPIOR}
-P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_unit.cmake)
# One point of the exhaustive matrix, named from its resolved parameters
# so the enumeration cannot collide with itself. `pins` is empty for the
# default pair, or the index of the USART whose own pins a bit-banged
# link sits on. Unreachable rates drop out here rather than aborting the
# configure.
# The optional trailing argument is the one-wire shape of the same link:
# ONE_WIRE folds a software point onto its RX pin (the default, or the
# named USART's RXD), HALF_DUPLEX is the hardware USART's turn-around.
function(pureboot_matrix_point hz baud link pins)
set(_name pbm_${hz}_${baud}_${link})
if(link STREQUAL "software")
pureboot_baud_feasible(${hz} ${baud} 1 _ok)
set(_args SERIAL software)
if(NOT pins STREQUAL "")
list(APPEND _args RX ${PUREBOOT_USART${pins}_RX} TX ${PUREBOOT_USART${pins}_TX})
set(_name ${_name}_on${pins})
endif()
if(ARGC GREATER 4 AND ARGV4 STREQUAL "ONE_WIRE")
if(NOT pins STREQUAL "")
set(_args SERIAL software RX ${PUREBOOT_USART${pins}_RX} TX ${PUREBOOT_USART${pins}_RX})
else()
list(APPEND _args RX pb0 TX pb0)
endif()
set(_name ${_name}_1w)
endif()
else()
pureboot_baud_feasible(${hz} ${baud} 0 _ok)
set(_args USART ${link})
if(ARGC GREATER 4 AND ARGV4 STREQUAL "HALF_DUPLEX")
list(APPEND _args HALF_DUPLEX)
set(_name ${_name}_hd)
endif()
endif()
if(_ok)
pureboot_size_variant(${_name} CLOCK ${hz} BAUD ${baud} ${_args})
endif()
endfunction()
# Clock points: the shipped-fuse floor (CKDIV8), the calibrated RC, and
# the crystal the stock build assumes (the tiny13's ladder is its own RC
# menu — it has no crystal option).
if(LIBAVR_MCU MATCHES "^attiny13")
set(_matrix_clocks 1200000 4800000 9600000)
set(_full_clocks 128000 600000 1200000 4800000 9600000)
else()
set(_matrix_clocks 1000000 8000000 16000000)
set(_full_clocks 128000 1000000 1843200 2000000 3686400 4000000 7372800 8000000
11059200 12000000 14745600 16000000 18432000 20000000)
endif()
# The exhaustive cross product: every clock a deployment plausibly runs
# — the internal oscillators, the shipped CKDIV8 floor, the plain
# crystals and the UART crystals — against every rate, against every
# backend. Beyond the ladder the list carries the slow rates a
# sub-megahertz oscillator is left with, which no ladder rate reaches
# (16000 Bd is the only rate the 128 kHz oscillator holds exactly); at
# the fast clocks those same rates also select the software UART's
# 16-bit _delay_loop_2 bit spin (two words more setup at each of its five
# sites), the largest image the space produces and a shape the ladder
# default — always the *fastest* rate a clock reaches — never picks.
#
# Every chip runs the full cross product: the size-bearing classes (flash
# addressing, hand-over shape, page size, USART inventory) are what make
# the image differ, and a chip outside them is expected to match its class
# — but "expected" is what a matrix is for, and the whole sweep is cheap
# enough to run rather than reason about. PUREBOOT_FULL_MATRIX is what
# selects it; the compact matrix below is the per-commit default.
get_property(_full_bauds GLOBAL PROPERTY PUREBOOT_BAUD_LADDER)
list(APPEND _full_bauds 16000 4800 2400 1200)
if(DEFINED ENV{PUREBOOT_FULL_MATRIX})
foreach(_matrix_hz IN LISTS _full_clocks)
foreach(_matrix_baud IN LISTS _full_bauds)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} software "")
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} software "" ONE_WIRE)
if(PUREBOOT_HAS_USART)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} software 0)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} software 0 ONE_WIRE)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} 0 "")
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} 0 "" HALF_DUPLEX)
endif()
if(PUREBOOT_HAS_USART1)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} software 1)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} software 1 ONE_WIRE)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} 1 "")
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} 1 "" HALF_DUPLEX)
endif()
endforeach()
endforeach()
else()
foreach(_matrix_hz IN LISTS _matrix_clocks)
math(EXPR _matrix_khz "${_matrix_hz} / 1000")
if(PUREBOOT_HAS_USART OR NOT _matrix_hz EQUAL _pb_stock_hz)
pureboot_size_variant(pureboot_sw_${_matrix_khz}k CLOCK ${_matrix_hz} SERIAL software)
endif()
if(PUREBOOT_HAS_USART AND NOT _matrix_hz EQUAL _pb_stock_hz)
pureboot_size_variant(pureboot_hw_${_matrix_khz}k CLOCK ${_matrix_hz} SERIAL hardware)
endif()
if(PUREBOOT_HAS_USART1 AND NOT _matrix_hz EQUAL _pb_stock_hz)
pureboot_size_variant(pureboot_usart1_${_matrix_khz}k CLOCK ${_matrix_hz} USART 1)
endif()
endforeach()
list(GET _matrix_clocks -1 _matrix_top_hz)
pureboot_size_variant(pureboot_sw_wide CLOCK ${_matrix_top_hz} BAUD 9600 SERIAL software)
# The pin axis at the widest software image — the slowest ladder rate
# against the fastest clock, whose bit spin needs the 16-bit delay
# loop — with the USART release on top of it. The exhaustive sweep
# above carries the same axis across its whole cross product.
if(PUREBOOT_HAS_USART)
pureboot_size_variant(pureboot_sw_wide_on_usart0 CLOCK ${_matrix_top_hz} BAUD 9600
SERIAL software RX ${PUREBOOT_USART0_RX} TX ${PUREBOOT_USART0_TX})
endif()
if(PUREBOOT_HAS_USART1)
pureboot_size_variant(pureboot_sw_wide_on_usart1 CLOCK ${_matrix_top_hz} BAUD 9600
SERIAL software RX ${PUREBOOT_USART1_RX} TX ${PUREBOOT_USART1_TX})
endif()
endif()
if(PUREBOOT_HAS_USART1)
pureboot_size_variant(pureboot_usart1 USART 1)
endif()
# The pin axis at its fixed points, in both matrix modes. The autobaud
# loader carries no clock and no baud, so the sweep has nothing to vary
# for it — yet it is the tightest image in the space, and on a USART's
# own pins it pays the release too: that combination is the one that
# overflowed the 1284's slot. The software build on those pins is the
# same deployment the mute test drives.
if(PUREBOOT_HAS_USART)
pureboot_size_variant(pureboot_sw_on_usart0 SERIAL software
RX ${PUREBOOT_USART0_RX} TX ${PUREBOOT_USART0_TX})
pureboot_size_variant(pureboot_autobaud_on_usart0 SERIAL autobaud
RX ${PUREBOOT_USART0_RX} TX ${PUREBOOT_USART0_TX})
endif()
if(PUREBOOT_HAS_USART1)
pureboot_size_variant(pureboot_sw_on_usart1 SERIAL software
RX ${PUREBOOT_USART1_RX} TX ${PUREBOOT_USART1_TX})
pureboot_size_variant(pureboot_autobaud_on_usart1 SERIAL autobaud
RX ${PUREBOOT_USART1_RX} TX ${PUREBOOT_USART1_TX})
endif()
# The OSCCAL axis at its fixed points: the stock shape, and the tightest
# image in the space with the trim on top — the axis adds one register
# write, and these points hold both of its addressing encodings to every
# chip's budget.
pureboot_size_variant(pureboot_osccal OSCCAL 0x9c)
pureboot_size_variant(pureboot_autobaud_osccal SERIAL autobaud OSCCAL 0x9c)
if(PUREBOOT_HAS_USART)
pureboot_size_variant(pureboot_autobaud_osccal_on_usart0 SERIAL autobaud OSCCAL 0x9c
RX ${PUREBOOT_USART0_RX} TX ${PUREBOOT_USART0_TX})
endif()
# The one-wire axis at its fixed points, in both matrix modes (the
# exhaustive sweep carries the same shapes across its cross product):
# the software link folded onto one pin, the tightest autobaud image
# likewise — on the default pin and on the USART's own RXD, whose
# release the now-driven shared pin needs where a receive-only link
# would not — and the hardware USART's half-duplex turn-around, stock
# and at the widest fixed-baud shape.
# The two spellings deliberately split across the two points: HALF_DUPLEX
# folds TX onto RX, RX == TX states the same thing directly.
pureboot_size_variant(pureboot_1w SERIAL software RX pb0 HALF_DUPLEX)
pureboot_size_variant(pureboot_1w_autobaud_osccal SERIAL autobaud OSCCAL 0x9c RX pb0 TX pb0)
if(PUREBOOT_HAS_USART)
pureboot_size_variant(pureboot_1w_on_usart0 SERIAL software
RX ${PUREBOOT_USART0_RX} TX ${PUREBOOT_USART0_RX})
pureboot_size_variant(pureboot_1w_autobaud_osccal_on_usart0 SERIAL autobaud OSCCAL 0x9c
RX ${PUREBOOT_USART0_RX} TX ${PUREBOOT_USART0_RX})
pureboot_size_variant(pureboot_hd HALF_DUPLEX)
list(GET _matrix_clocks -1 _hd_top_hz)
pureboot_size_variant(pureboot_hd_wide CLOCK ${_hd_top_hz} BAUD 9600 HALF_DUPLEX)
endif()
if(PUREBOOT_HAS_USART1)
pureboot_size_variant(pureboot_usart1_hd USART 1 HALF_DUPLEX)
endif()
# The trim byte, observed through the wire from the first prompt — one
# chip per OSCCAL addressing class: extended I/O on the 328P (data 0x66,
# an sts — DS40002061B §36), plain I/O on the 85 (data 0x51, an out —
# Atmel-2586 §21).
if(LIBAVR_MCU MATCHES "^(atmega328p|attiny85)$" AND DEFINED PB_DEVICE)
if(LIBAVR_MCU STREQUAL "atmega328p")
set(_osccal_addr 0x66)
else()
set(_osccal_addr 0x51)
endif()
get_target_property(_osccal_hz pureboot_osccal PUREBOOT_HZ)
get_target_property(_osccal_baud pureboot_osccal PUREBOOT_BAUD)
add_test(NAME pureboot.osccal
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbosccal.py
${PB_DEVICE} $<TARGET_FILE:pureboot_osccal> ${PUREBOOT_SIM_MCU}
${_osccal_hz} ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_osccal_baud}
${_osccal_addr} 0x9c ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbosccal-work)
set_tests_properties(pureboot.osccal PROPERTIES TIMEOUT 120)
endif()
# One configured deployment end to end — a real board's shape rather
# than the stock assumption: the ATmega328P on its shipped 1 MHz fuses,
# the software UART on hand-picked pins (TX = PB1, RX = PB5), the ladder
# baud (9600). The full protocol suite runs against it, fixture
# application included, over the runner's GPIO bridge — proving the
# configuration plumbing produces a working loader, not just one that
# fits.
if(LIBAVR_MCU STREQUAL "atmega328p" AND DEFINED PB_DEVICE)
pureboot_size_variant(pureboot_custom CLOCK 1000000 SERIAL software RX pb5 TX pb1)
get_target_property(_custom_hz pureboot_custom PUREBOOT_HZ)
get_target_property(_custom_baud pureboot_custom PUREBOOT_BAUD)
get_target_property(_custom_link pureboot_custom PUREBOOT_LINK)
add_executable(pbapp_custom test/pbapp.cpp)
target_link_libraries(pbapp_custom PRIVATE libavr)
target_compile_definitions(pbapp_custom PRIVATE PUREBOOT_CLOCK_HZ=${_custom_hz}
PUREBOOT_BAUD=${_custom_baud} PUREBOOT_SOFT_SERIAL PUREBOOT_TX=pb1)
add_custom_command(TARGET pbapp_custom POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary
$<TARGET_FILE:pbapp_custom> $<TARGET_FILE:pbapp_custom>.bin)
add_test(NAME pureboot.custom
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
${PB_DEVICE} $<TARGET_FILE:pureboot_custom> ${PUREBOOT_SIM_MCU} ${_custom_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_custom_baud} ${PUREBOOT_EEPROM}
$<TARGET_FILE:pbapp_custom>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbcustom-work ${_custom_link})
set_tests_properties(pureboot.custom PROPERTIES TIMEOUT 180)
endif()
# Hand-over with the USART that owns the loader's pins left enabled — the
# state an application reaches by jumping in without a reset, and the one
# that made a bit-banged loader on PD0/PD1 (where the Uno's USB bridge
# lands) receive and obey while answering nothing. Run where it was found
# on silicon; the runner supplies the pin ownership simavr has no model
# for, which is what lets this fail when the release is gone.
if(LIBAVR_MCU STREQUAL "atmega328p" AND DEFINED PB_DEVICE)
get_target_property(_mute_hz pureboot_sw_on_usart0 PUREBOOT_HZ)
get_target_property(_mute_baud pureboot_sw_on_usart0 PUREBOOT_BAUD)
get_target_property(_mute_link pureboot_sw_on_usart0 PUREBOOT_LINK)
add_executable(pbapp_handover test/pbapp.cpp)
target_link_libraries(pbapp_handover PRIVATE libavr)
target_compile_definitions(pbapp_handover PRIVATE PUREBOOT_CLOCK_HZ=${_mute_hz}
PUREBOOT_BAUD=${_mute_baud} PUREBOOT_HANDOVER)
add_custom_command(TARGET pbapp_handover POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary
$<TARGET_FILE:pbapp_handover> $<TARGET_FILE:pbapp_handover>.bin)
add_test(NAME pureboot.mute
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbmute.py
${PB_DEVICE} $<TARGET_FILE:pureboot_sw_on_usart0> ${PUREBOOT_SIM_MCU} ${_mute_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_mute_baud}
$<TARGET_FILE:pbapp_handover>.bin
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbmute-work ${_mute_link})
set_tests_properties(pureboot.mute PROPERTIES TIMEOUT 180)
# The same hand-over against the one-wire deployment on that USART's
# RXD: RXEN forces the shared pin's direction, so a loader that only
# released the transmit-side hold would read the wire and answer into
# a pin it cannot drive. The host runs with the --one-wire echo
# discard, which the bridge's shared-line model feeds for real.
get_target_property(_mute1w_link pureboot_1w_on_usart0 PUREBOOT_LINK)
add_test(NAME pureboot.mute.onewire
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbmute.py
${PB_DEVICE} $<TARGET_FILE:pureboot_1w_on_usart0> ${PUREBOOT_SIM_MCU} ${_mute_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_mute_baud}
$<TARGET_FILE:pbapp_handover>.bin
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbmute-1w-work ${_mute1w_link})
set_tests_properties(pureboot.mute.onewire PROPERTIES TIMEOUT 180)
# The full protocol suite over one shared pin: the loader folded onto
# PB0, the bridge following the pin's direction, the fixture
# bannering as a guest on the same line, and the host discarding its
# own echo throughout.
get_target_property(_1w_hz pureboot_1w PUREBOOT_HZ)
get_target_property(_1w_baud pureboot_1w PUREBOOT_BAUD)
get_target_property(_1w_link pureboot_1w PUREBOOT_LINK)
add_executable(pbapp_1w test/pbapp.cpp)
target_link_libraries(pbapp_1w PRIVATE libavr)
target_compile_definitions(pbapp_1w PRIVATE PUREBOOT_CLOCK_HZ=${_1w_hz}
PUREBOOT_BAUD=${_1w_baud} PUREBOOT_SOFT_SERIAL
PUREBOOT_RX=pb0 PUREBOOT_TX=pb0)
add_custom_command(TARGET pbapp_1w POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary
$<TARGET_FILE:pbapp_1w> $<TARGET_FILE:pbapp_1w>.bin)
add_test(NAME pureboot.onewire
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
${PB_DEVICE} $<TARGET_FILE:pureboot_1w> ${PUREBOOT_SIM_MCU} ${_1w_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_1w_baud} ${PUREBOOT_EEPROM}
$<TARGET_FILE:pbapp_1w>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pb1w-work ${_1w_link})
set_tests_properties(pureboot.onewire PROPERTIES TIMEOUT 180)
# The hardware USART's half-duplex turn-around, end to end: every
# reply byte runs drive-line, TXC-hold, release — against simavr's
# RXEN-gated receiver, which drops input to a disabled receiver the
# way silicon does. The pty is a two-wire transport, so the host
# needs no echo discard here; the off-chip tie itself is the
# hardware bench's item.
add_test(NAME pureboot.halfduplex
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
${PB_DEVICE} $<TARGET_FILE:pureboot_hd> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud} ${PUREBOOT_EEPROM}
$<TARGET_FILE:pbapp>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbhd-work)
set_tests_properties(pureboot.halfduplex PROPERTIES TIMEOUT 180)
endif()
# The second USART, driven for real on one chip: instance selection is
# compile-checked everywhere, but only a live session proves the loader
# initialized and polls the USART it claims to. The fixture application
# banners on the same instance.
if(LIBAVR_MCU STREQUAL "atmega644a" AND DEFINED PB_DEVICE)
get_target_property(_usart1_hz pureboot_usart1 PUREBOOT_HZ)
get_target_property(_usart1_baud pureboot_usart1 PUREBOOT_BAUD)
add_executable(pbapp_usart1 test/pbapp.cpp)
target_link_libraries(pbapp_usart1 PRIVATE libavr)
target_compile_definitions(pbapp_usart1 PRIVATE PUREBOOT_CLOCK_HZ=${_usart1_hz}
PUREBOOT_BAUD=${_usart1_baud} PUREBOOT_USART=1)
add_custom_command(TARGET pbapp_usart1 POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary
$<TARGET_FILE:pbapp_usart1> $<TARGET_FILE:pbapp_usart1>.bin)
add_test(NAME pureboot.usart1
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
${PB_DEVICE} $<TARGET_FILE:pureboot_usart1> ${PUREBOOT_SIM_MCU} ${_usart1_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_usart1_baud} ${PUREBOOT_EEPROM}
$<TARGET_FILE:pbapp_usart1>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbusart1-work usart1)
set_tests_properties(pureboot.usart1 PROPERTIES TIMEOUT 180)
endif()
# The autobaud loader driven end to end over the software-UART bridge:
# the host sends the 0xC0 calibration pulse, the loader times it, locks,
# and programs. Run on the near-flash 328P
# and the word-addressed 1284P — the two flash-addressing classes — and each
# at two clocks with the one binary, which is the clock-agnostic property
# autobaud exists for (test/pbautobaud.py). The fixture application banners
# over the same software link at the first clock's rate.
if(LIBAVR_MCU MATCHES "^atmega(328p|1284p)$" AND DEFINED PB_DEVICE)
add_executable(pbapp_autobaud test/pbapp.cpp)
target_link_libraries(pbapp_autobaud PRIVATE libavr)
target_compile_definitions(pbapp_autobaud PRIVATE PUREBOOT_CLOCK_HZ=1000000
PUREBOOT_BAUD=9600 PUREBOOT_SOFT_SERIAL PUREBOOT_TX=pb1)
add_custom_command(TARGET pbapp_autobaud POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary
$<TARGET_FILE:pbapp_autobaud> $<TARGET_FILE:pbapp_autobaud>.bin)
add_test(NAME pureboot.autobaud
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbautobaud.py
${PB_DEVICE} $<TARGET_FILE:pureboot_autobaud> ${PUREBOOT_SIM_MCU}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} $<TARGET_FILE:pbapp_autobaud>.bin
1000000 9600 ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbautobaud-work)
set_tests_properties(pureboot.autobaud PROPERTIES TIMEOUT 240)
# The tightest deployment in the space, end to end: the autobaud
# loader folded onto the USART's own RXD with the OSCCAL trim baked
# — one-wire calibration, the receive-side release, and the host's
# echo discard, over the same two-clock sweep. One chip carries it;
# the shape is chip-independent.
if(LIBAVR_MCU STREQUAL "atmega328p")
get_target_property(_ab1w_link pureboot_1w_autobaud_osccal_on_usart0 PUREBOOT_LINK)
add_executable(pbapp_autobaud_1w test/pbapp.cpp)
target_link_libraries(pbapp_autobaud_1w PRIVATE libavr)
target_compile_definitions(pbapp_autobaud_1w PRIVATE PUREBOOT_CLOCK_HZ=1000000
PUREBOOT_BAUD=9600 PUREBOOT_SOFT_SERIAL
PUREBOOT_RX=pd0 PUREBOOT_TX=pd0)
add_custom_command(TARGET pbapp_autobaud_1w POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary
$<TARGET_FILE:pbapp_autobaud_1w> $<TARGET_FILE:pbapp_autobaud_1w>.bin)
add_test(NAME pureboot.autobaud.onewire
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbautobaud.py
${PB_DEVICE} $<TARGET_FILE:pureboot_1w_autobaud_osccal_on_usart0>
${PUREBOOT_SIM_MCU} ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE}
$<TARGET_FILE:pbapp_autobaud_1w>.bin
1000000 9600 ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbautobaud-1w-work ${_ab1w_link})
set_tests_properties(pureboot.autobaud.onewire PROPERTIES TIMEOUT 240)
endif()
# The autobaud window: the calibration poll budget, at the measured
# 10 cycles a poll (pbwindow.py pins the constant the README's
# seconds arithmetic uses; the budget itself is the clock-free knob).
add_test(NAME pureboot.window.autobaud
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbwindow.py
--device ${PB_DEVICE} --loader $<TARGET_FILE:pureboot_autobaud>
--mcu ${PUREBOOT_SIM_MCU} --hz 1000000
--base ${PUREBOOT_BASE_HEX} --page ${PUREBOOT_PAGE}
--baud 9600 --app $<TARGET_FILE:pbapp_autobaud>.bin
--autobaud-polls 4000000 --link sw
--tool ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
--workdir ${CMAKE_BINARY_DIR}/pbwindow-autobaud-work)
set_tests_properties(pureboot.window.autobaud PROPERTIES TIMEOUT 300)
endif()
endif()

1655
CMakePresets.json Normal file
View File

File diff suppressed because it is too large Load Diff

239
blink/blink.cppproj
View File

@@ -1,239 +0,0 @@
<?xml version="1.0" encoding="utf-8"?>
<Project DefaultTargets="Build" xmlns="http://schemas.microsoft.com/developer/msbuild/2003" ToolsVersion="14.0">
<PropertyGroup>
<SchemaVersion>2.0</SchemaVersion>
<ProjectVersion>7.0</ProjectVersion>
<ToolchainName>com.Atmel.AVRGCC8.CPP</ToolchainName>
<ProjectGuid>{d887fc8e-ee68-4248-8382-92dbc9a54145}</ProjectGuid>
<avrdevice>ATmega328P</avrdevice>
<avrdeviceseries>none</avrdeviceseries>
<OutputType>Executable</OutputType>
<Language>CPP</Language>
<OutputFileName>$(MSBuildProjectName)</OutputFileName>
<OutputFileExtension>.elf</OutputFileExtension>
<OutputDirectory>$(MSBuildProjectDirectory)\$(Configuration)</OutputDirectory>
<AssemblyName>blink</AssemblyName>
<Name>blink</Name>
<RootNamespace>blink</RootNamespace>
<ToolchainFlavour>avr-g++-9.1.0</ToolchainFlavour>
<KeepTimersRunning>true</KeepTimersRunning>
<OverrideVtor>false</OverrideVtor>
<CacheFlash>true</CacheFlash>
<ProgFlashFromRam>true</ProgFlashFromRam>
<RamSnippetAddress>0x20000000</RamSnippetAddress>
<UncachedRange />
<preserveEEPROM>true</preserveEEPROM>
<OverrideVtorValue>exception_table</OverrideVtorValue>
<BootSegment>2</BootSegment>
<ResetRule>0</ResetRule>
<eraseonlaunchrule>0</eraseonlaunchrule>
<EraseKey />
<avrtool>com.atmel.avrdbg.tool.atmelice</avrtool>
<avrtoolserialnumber>J41800099437</avrtoolserialnumber>
<avrdeviceexpectedsignature>0x1E950F</avrdeviceexpectedsignature>
<com_atmel_avrdbg_tool_stk500>
<ToolOptions>
<InterfaceProperties>
<IspClock>125000</IspClock>
</InterfaceProperties>
<InterfaceName>ISP</InterfaceName>
</ToolOptions>
<ToolType>com.atmel.avrdbg.tool.stk500</ToolType>
<ToolNumber>
</ToolNumber>
<ToolName>STK500</ToolName>
</com_atmel_avrdbg_tool_stk500>
<avrtoolinterface>ISP</avrtoolinterface>
<avrtoolinterfaceclock>125000</avrtoolinterfaceclock>
<AsfFrameworkConfig>
<framework-data xmlns="">
<options />
<configurations />
<files />
<documentation help="" />
<offline-documentation help="" />
<dependencies>
<content-extension eid="atmel.asf" uuidref="Atmel.ASF" version="3.47.0" />
</dependencies>
</framework-data>
</AsfFrameworkConfig>
<com_atmel_avrdbg_tool_atmelice>
<ToolOptions>
<InterfaceProperties>
<IspClock>125000</IspClock>
</InterfaceProperties>
<InterfaceName>ISP</InterfaceName>
</ToolOptions>
<ToolType>com.atmel.avrdbg.tool.atmelice</ToolType>
<ToolNumber>J41800099437</ToolNumber>
<ToolName>Atmel-ICE</ToolName>
</com_atmel_avrdbg_tool_atmelice>
<custom>
<ToolOptions>
<InterfaceProperties>
<IspClock>125000</IspClock>
</InterfaceProperties>
<InterfaceName>
</InterfaceName>
</ToolOptions>
<ToolType>custom</ToolType>
<ToolNumber>
</ToolNumber>
<ToolName>Custom Programming Tool</ToolName>
</custom>
<com_atmel_avrdbg_tool_simulator>
<ToolOptions xmlns="">
<InterfaceProperties>
</InterfaceProperties>
<InterfaceName>
</InterfaceName>
</ToolOptions>
<ToolType xmlns="">com.atmel.avrdbg.tool.simulator</ToolType>
<ToolNumber xmlns="">
</ToolNumber>
<ToolName xmlns="">Simulator</ToolName>
</com_atmel_avrdbg_tool_simulator>
<AAFDebugger>
<AAFDebugFiles>
</AAFDebugFiles>
</AAFDebugger>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Release' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcc.compiler.symbols.DefSymbols>
<ListValues>
<Value>NDEBUG</Value>
</ListValues>
</avrgcc.compiler.symbols.DefSymbols>
<avrgcc.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcc.compiler.directories.IncludePaths>
<avrgcc.compiler.optimization.level>Optimize for size (-Os)</avrgcc.compiler.optimization.level>
<avrgcc.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcc.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcc.compiler.warnings.AllWarnings>True</avrgcc.compiler.warnings.AllWarnings>
<avrgcc.compiler.warnings.ExtraWarnings>True</avrgcc.compiler.warnings.ExtraWarnings>
<avrgcc.compiler.warnings.Pedantic>True</avrgcc.compiler.warnings.Pedantic>
<avrgcc.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -std=c11</avrgcc.compiler.miscellaneous.OtherFlags>
<avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>NDEBUG</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize for size (-Os)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.warnings.Pedantic>True</avrgcccpp.compiler.warnings.Pedantic>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -Wextra -std=c++17</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.libraries.Libraries>
<ListValues>
<Value>libm</Value>
</ListValues>
</avrgcccpp.linker.libraries.Libraries>
<avrgcccpp.assembler.general.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.assembler.general.IncludePaths>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Debug' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcc.compiler.symbols.DefSymbols>
<ListValues>
<Value>DEBUG</Value>
</ListValues>
</avrgcc.compiler.symbols.DefSymbols>
<avrgcc.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcc.compiler.directories.IncludePaths>
<avrgcc.compiler.optimization.level>Optimize (-O1)</avrgcc.compiler.optimization.level>
<avrgcc.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcc.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcc.compiler.optimization.DebugLevel>Maximum (-g3)</avrgcc.compiler.optimization.DebugLevel>
<avrgcc.compiler.warnings.AllWarnings>True</avrgcc.compiler.warnings.AllWarnings>
<avrgcc.compiler.warnings.ExtraWarnings>True</avrgcc.compiler.warnings.ExtraWarnings>
<avrgcc.compiler.warnings.Pedantic>True</avrgcc.compiler.warnings.Pedantic>
<avrgcc.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -std=c11</avrgcc.compiler.miscellaneous.OtherFlags>
<avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>DEBUG</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize (-O1)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcccpp.compiler.optimization.DebugLevel>Maximum (-g3)</avrgcccpp.compiler.optimization.DebugLevel>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.warnings.Pedantic>True</avrgcccpp.compiler.warnings.Pedantic>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -Wextra -std=c++17</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.libraries.Libraries>
<ListValues>
<Value>libm</Value>
</ListValues>
</avrgcccpp.linker.libraries.Libraries>
<avrgcccpp.assembler.general.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.assembler.general.IncludePaths>
<avrgcccpp.assembler.debugging.DebugLevel>Default (-Wa,-g)</avrgcccpp.assembler.debugging.DebugLevel>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<ItemGroup>
<Compile Include="bootloader.cpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="bootloader.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="clock.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="io\io.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="main.cpp">
<SubType>compile</SubType>
</Compile>
</ItemGroup>
<ItemGroup>
<Folder Include="io" />
</ItemGroup>
<Import Project="$(AVRSTUDIO_EXE_PATH)\\Vs\\Compiler.targets" />
</Project>

46
blink/bootloader.cpp
View File

@@ -1,46 +0,0 @@
#include "bootloader.hpp"
#include <avr/io.h>
#include <avr/pgmspace.h>
#include <avr/wdt.h>
namespace {
typedef void (*jmp_fn)() __attribute__((noreturn));
jmp_fn boot = reinterpret_cast<jmp_fn>(0x0000);
jmp_fn bootloader = reinterpret_cast<jmp_fn>(0x7800 / 2);
} // namespace
bool Bootloader::handleReset()
{
wdt_reset();
uint8_t mcuStatus = MCUSR;
MCUSR &= ~(1 << WDRF);
wdt_disable();
return (mcuStatus & (1 << WDRF));
}
void Bootloader::reset()
{
wdt_enable(WDTO_15MS);
while (true)
;
}
bool Bootloader::check()
{
if (pgm_read_byte(reinterpret_cast<uint16_t>(bootloader) * 2) != 0xFF)
return true;
return false;
}
void Bootloader::call()
{
if (check())
bootloader();
else
boot();
}

24
blink/bootloader.hpp
View File

@@ -1,24 +0,0 @@
#pragma once
class Bootloader {
public:
template <typename Fn>
static inline void init(Fn callback)
{
if (handleReset()) {
callback();
call();
}
}
static inline void enter()
{
reset();
}
private:
static bool handleReset();
static void reset();
static bool check();
static void call();
};

5
blink/clock.hpp
View File

@@ -1,5 +0,0 @@
#pragma once
//#define F_CPU 18'432'000
#define F_CPU 16'000'000
#include <util/delay.h>

1
blink/io

Submodule blink/io deleted from 80de36ee7e

30
blink/main.cpp
View File

@@ -1,30 +0,0 @@
#include "clock.hpp"
#include "io/io.hpp"
#include "bootloader.hpp"
int main()
{
io::Pin<io::P::B5> ledPin;
ledPin.dir(io::Dir::OUT);
ledPin = false;
Bootloader::init([&ledPin]() {
for (uint8_t i = 0; i < 10; ++i) {
ledPin = true;
_delay_ms(50);
ledPin = false;
_delay_ms(50);
}
});
for (uint8_t i = 0; i < 10; ++i) {
ledPin.toggle();
_delay_ms(1000);
}
Bootloader::enter();
return 0;
}

34
bootloader.atsln
View File

@@ -1,34 +0,0 @@
Microsoft Visual Studio Solution File, Format Version 12.00
# Atmel Studio Solution File, Format Version 11.00
VisualStudioVersion = 14.0.23107.0
MinimumVisualStudioVersion = 10.0.40219.1
Project("{E66E83B9-2572-4076-B26E-6BE79FF3018A}") = "tsb", "tsb\tsb.cppproj", "{DCE6C7E3-EE26-4D79-826B-08594B9AD897}"
EndProject
Project("{E66E83B9-2572-4076-B26E-6BE79FF3018A}") = "stk500v2", "stk500v2\stk500v2.cppproj", "{19798CCE-5D96-40E9-B769-D209715DCE0C}"
EndProject
Project("{E66E83B9-2572-4076-B26E-6BE79FF3018A}") = "blink", "blink\blink.cppproj", "{D887FC8E-EE68-4248-8382-92DBC9A54145}"
EndProject
Global
GlobalSection(SolutionConfigurationPlatforms) = preSolution
Debug|AVR = Debug|AVR
Release|AVR = Release|AVR
EndGlobalSection
GlobalSection(ProjectConfigurationPlatforms) = postSolution
{DCE6C7E3-EE26-4D79-826B-08594B9AD897}.Debug|AVR.ActiveCfg = Debug|AVR
{DCE6C7E3-EE26-4D79-826B-08594B9AD897}.Debug|AVR.Build.0 = Debug|AVR
{DCE6C7E3-EE26-4D79-826B-08594B9AD897}.Release|AVR.ActiveCfg = Release|AVR
{DCE6C7E3-EE26-4D79-826B-08594B9AD897}.Release|AVR.Build.0 = Release|AVR
{19798CCE-5D96-40E9-B769-D209715DCE0C}.Debug|AVR.ActiveCfg = Debug|AVR
{19798CCE-5D96-40E9-B769-D209715DCE0C}.Debug|AVR.Build.0 = Debug|AVR
{19798CCE-5D96-40E9-B769-D209715DCE0C}.Release|AVR.ActiveCfg = Release|AVR
{19798CCE-5D96-40E9-B769-D209715DCE0C}.Release|AVR.Build.0 = Release|AVR
{D887FC8E-EE68-4248-8382-92DBC9A54145}.Debug|AVR.ActiveCfg = Debug|AVR
{D887FC8E-EE68-4248-8382-92DBC9A54145}.Debug|AVR.Build.0 = Debug|AVR
{D887FC8E-EE68-4248-8382-92DBC9A54145}.Release|AVR.ActiveCfg = Release|AVR
{D887FC8E-EE68-4248-8382-92DBC9A54145}.Release|AVR.Build.0 = Release|AVR
EndGlobalSection
GlobalSection(SolutionProperties) = preSolution
HideSolutionNode = FALSE
EndGlobalSection
EndGlobal

77
ide/README.md Normal file
View File

@@ -0,0 +1,77 @@
# Atmel Studio
`master` carries `bootloader.atsln`, so this branch does too: `ide/bootloader.atsln`
builds the loaders from the same sources Ninja does, to a **byte-identical
`.text`** — 390 B for the 328P pureboot loader, 510 B for the `tsb_asm` tier in
its 512-byte section. CMake remains the build system; the solution is here so the
port opens in Studio as its predecessor did.
## The two projects, and why two
pureboot is a chip × backend × clock × baud matrix — `pureboot_add_loader()`
resolves a deployment into compile definitions — and a `.cppproj` is one binary
at one set of flags, so a project can only ever be one point of it. `pureboot`
is that point: the stock 328P deployment, USART0 at 115200 on a 16 MHz crystal,
an 8-second activation window. `tsb_asm` is the TinySafeBoot tier that occupies
the same 512-byte section `master`'s `tsb` project targeted.
The other three tsb tiers (`tsb_pure`, `tsb_tricks`, `tsb_policy`) are not here.
They differ from `tsb_asm` in their source file, their section size, and — for
`tsb_policy` — two loop flags; nothing about that is a Studio concern, and what
they exist to demonstrate is a size gradient only the CMake size tests measure.
Adding one is a copy of `tsb_asm/tsb_asm.cppproj` in its own directory, with its
name, its GUID, its source path and its `--section-start` changed (`0x7c00` for
the 1 KiB tiers), plus four lines in the solution.
`avrdevice` is a project property, so each project gets its own directory:
Studio builds into `<project dir>/<Configuration>` whatever `OutputDirectory`
says, and two projects sharing a directory would share one object file.
## Debug keeps `-Os`
Both configurations compile at `-Os`; Debug adds only `-gdwarf-4`. The `.text`
is therefore identical in both, which is the point — a loader's section is a
**correctness** bound and not a budget. `-Og` builds this same source to 590 B,
and linking it at `--section-start=.text=0x7e00` on a 32 KiB part puts 78 bytes
past flash end **without a diagnostic**: `rcall`/`rjmp` targets there wrap
modulo flash size, so the image dies right after activation. A debug
configuration that silently produces that is worse than none, and DWARF costs no
flash, so the optimisation level stays where correctness needs it.
## What Studio needs from the machine
libavr from the **submodule**, found at
`$(MSBuildProjectDirectory)\..\..\libavr\include` — correct by construction, and
anchored to the project because a plain relative path resolves against the
generated makefile's directory (the configuration's output directory), not the
project's. There is no `LIBAVR_ROOT` escape hatch: a variable exported in a
shell is invisible to Studio launched from the Start menu, and the failure reads
as a missing `libavr/libavr.hpp` — which is what the submodule answers.
A GCC 16.1 toolchain registered as flavour `avr-g++-16.1.0`, nothing older
reaching `-std=c++26`.
## Generating and gating
One generated file is required before a project will load at all, and one command
per project checks the flags have not drifted (both from libavr's
`tools/atmelstudio/`):
```sh
for name in pureboot tsb_asm; do
python libavr/tools/atmelstudio/componentinfo.py \
"ide/$name/$name.componentinfo.xml" --device ATmega328P
python libavr/tools/atmelstudio/check-flags.py \
--solution ide/bootloader.atsln --project "$name" --target "$name" \
--compile-commands build/atmega328p-generated/compile_commands.json \
--log "build/as-$name.log"
done
```
`--project` because one reference describes one binary; `--target` because
`pureboot.cpp` is compiled by every point of the size matrix and the flags
differ per point, so the basename alone does not name a reference. Release is
what the gate compares — the presets define no debug build, and Debug differs
from Release only in `-gdwarf-4`.
Legacy (the yazoalfa-era submodules) stays on `master`.

28
ide/bootloader.atsln Normal file
View File

@@ -0,0 +1,28 @@
Microsoft Visual Studio Solution File, Format Version 12.00
# Atmel Studio Solution File, Format Version 11.00
VisualStudioVersion = 14.0.23107.0
MinimumVisualStudioVersion = 10.0.40219.1
Project("{E66E83B9-2572-4076-B26E-6BE79FF3018A}") = "pureboot", "pureboot\pureboot.cppproj", "{99067222-32D5-49E3-B4F8-5ABA0F7722B7}"
EndProject
Project("{E66E83B9-2572-4076-B26E-6BE79FF3018A}") = "tsb_asm", "tsb_asm\tsb_asm.cppproj", "{6618D3BE-7EB3-49A2-9113-F128E396FF06}"
EndProject
Global
GlobalSection(SolutionConfigurationPlatforms) = preSolution
Debug|AVR = Debug|AVR
Release|AVR = Release|AVR
EndGlobalSection
GlobalSection(ProjectConfigurationPlatforms) = postSolution
{99067222-32D5-49E3-B4F8-5ABA0F7722B7}.Debug|AVR.ActiveCfg = Debug|AVR
{99067222-32D5-49E3-B4F8-5ABA0F7722B7}.Debug|AVR.Build.0 = Debug|AVR
{99067222-32D5-49E3-B4F8-5ABA0F7722B7}.Release|AVR.ActiveCfg = Release|AVR
{99067222-32D5-49E3-B4F8-5ABA0F7722B7}.Release|AVR.Build.0 = Release|AVR
{6618D3BE-7EB3-49A2-9113-F128E396FF06}.Debug|AVR.ActiveCfg = Debug|AVR
{6618D3BE-7EB3-49A2-9113-F128E396FF06}.Debug|AVR.Build.0 = Debug|AVR
{6618D3BE-7EB3-49A2-9113-F128E396FF06}.Release|AVR.ActiveCfg = Release|AVR
{6618D3BE-7EB3-49A2-9113-F128E396FF06}.Release|AVR.Build.0 = Release|AVR
EndGlobalSection
GlobalSection(SolutionProperties) = preSolution
HideSolutionNode = FALSE
EndGlobalSection
EndGlobal

118
ide/pureboot/pureboot.cppproj Normal file
View File

@@ -0,0 +1,118 @@
<?xml version="1.0" encoding="utf-8"?>
<Project DefaultTargets="Build" xmlns="http://schemas.microsoft.com/developer/msbuild/2003" ToolsVersion="14.0">
<PropertyGroup>
<SchemaVersion>2.0</SchemaVersion>
<ProjectVersion>7.0</ProjectVersion>
<ToolchainName>com.Atmel.AVRGCC8.CPP</ToolchainName>
<ProjectGuid>99067222-32d5-49e3-b4f8-5aba0f7722b7</ProjectGuid>
<avrdevice>ATmega328P</avrdevice>
<avrdeviceseries>none</avrdeviceseries>
<OutputType>Executable</OutputType>
<Language>CPP</Language>
<OutputFileName>$(MSBuildProjectName)</OutputFileName>
<OutputFileExtension>.elf</OutputFileExtension>
<OutputDirectory>$(MSBuildProjectDirectory)\$(Configuration)</OutputDirectory>
<AssemblyName>pureboot</AssemblyName>
<Name>pureboot</Name>
<RootNamespace>pureboot</RootNamespace>
<ToolchainFlavour>avr-g++-16.1.0</ToolchainFlavour>
<KeepTimersRunning>true</KeepTimersRunning>
<OverrideVtor>false</OverrideVtor>
<CacheFlash>true</CacheFlash>
<ProgFlashFromRam>true</ProgFlashFromRam>
<RamSnippetAddress>0x20000000</RamSnippetAddress>
<UncachedRange />
<preserveEEPROM>true</preserveEEPROM>
<OverrideVtorValue>exception_table</OverrideVtorValue>
<BootSegment>2</BootSegment>
<ResetRule>0</ResetRule>
<eraseonlaunchrule>0</eraseonlaunchrule>
<EraseKey />
<AsfFrameworkConfig>
<framework-data xmlns="">
<options />
<configurations />
<files />
<documentation help="" />
<offline-documentation help="" />
<dependencies>
<content-extension eid="atmel.asf" uuidref="Atmel.ASF" version="3.52.0" />
</dependencies>
</framework-data>
</AsfFrameworkConfig>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Release' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>NDEBUG</Value>
<Value>PUREBOOT_CLOCK_HZ=16000000</Value>
<Value>PUREBOOT_BAUD=115200</Value>
<Value>PUREBOOT_TIMEOUT=8</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>$(MSBuildProjectDirectory)\..\..\libavr\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize for size (-Os)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>
<avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-std=c++26 -Wextra -Werror -mrelax -fno-exceptions -fno-rtti -fno-threadsafe-statics -fno-ivopts -fira-algorithm=priority -fno-tree-ter -fno-split-wide-types</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.optimization.GarbageCollectUnusedSections>True</avrgcccpp.linker.optimization.GarbageCollectUnusedSections>
<avrgcccpp.linker.miscellaneous.LinkerFlags>-mrelax -nostartfiles -Wl,--section-start=.text=0x7e00 -Wl,--defsym=pureboot_app=0 -Wl,--pmem-wrap-around=32k</avrgcccpp.linker.miscellaneous.LinkerFlags>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Debug' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>DEBUG</Value>
<Value>PUREBOOT_CLOCK_HZ=16000000</Value>
<Value>PUREBOOT_BAUD=115200</Value>
<Value>PUREBOOT_TIMEOUT=8</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>$(MSBuildProjectDirectory)\..\..\libavr\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize for size (-Os)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>
<avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-std=c++26 -Wextra -Werror -mrelax -fno-exceptions -fno-rtti -fno-threadsafe-statics -fno-ivopts -fira-algorithm=priority -fno-tree-ter -fno-split-wide-types -gdwarf-4</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.optimization.GarbageCollectUnusedSections>True</avrgcccpp.linker.optimization.GarbageCollectUnusedSections>
<avrgcccpp.linker.miscellaneous.LinkerFlags>-mrelax -nostartfiles -Wl,--section-start=.text=0x7e00 -Wl,--defsym=pureboot_app=0 -Wl,--pmem-wrap-around=32k</avrgcccpp.linker.miscellaneous.LinkerFlags>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<ItemGroup>
<Compile Include="..\..\pureboot\pureboot.cpp">
<SubType>compile</SubType>
<Link>pureboot\pureboot.cpp</Link>
</Compile>
</ItemGroup>
<ItemGroup>
<Folder Include="pureboot" />
</ItemGroup>
<Import Project="$(AVRSTUDIO_EXE_PATH)\Vs\Compiler.targets" />
</Project>

112
ide/tsb_asm/tsb_asm.cppproj Normal file
View File

@@ -0,0 +1,112 @@
<?xml version="1.0" encoding="utf-8"?>
<Project DefaultTargets="Build" xmlns="http://schemas.microsoft.com/developer/msbuild/2003" ToolsVersion="14.0">
<PropertyGroup>
<SchemaVersion>2.0</SchemaVersion>
<ProjectVersion>7.0</ProjectVersion>
<ToolchainName>com.Atmel.AVRGCC8.CPP</ToolchainName>
<ProjectGuid>6618d3be-7eb3-49a2-9113-f128e396ff06</ProjectGuid>
<avrdevice>ATmega328P</avrdevice>
<avrdeviceseries>none</avrdeviceseries>
<OutputType>Executable</OutputType>
<Language>CPP</Language>
<OutputFileName>$(MSBuildProjectName)</OutputFileName>
<OutputFileExtension>.elf</OutputFileExtension>
<OutputDirectory>$(MSBuildProjectDirectory)\$(Configuration)</OutputDirectory>
<AssemblyName>tsb_asm</AssemblyName>
<Name>tsb_asm</Name>
<RootNamespace>tsb_asm</RootNamespace>
<ToolchainFlavour>avr-g++-16.1.0</ToolchainFlavour>
<KeepTimersRunning>true</KeepTimersRunning>
<OverrideVtor>false</OverrideVtor>
<CacheFlash>true</CacheFlash>
<ProgFlashFromRam>true</ProgFlashFromRam>
<RamSnippetAddress>0x20000000</RamSnippetAddress>
<UncachedRange />
<preserveEEPROM>true</preserveEEPROM>
<OverrideVtorValue>exception_table</OverrideVtorValue>
<BootSegment>2</BootSegment>
<ResetRule>0</ResetRule>
<eraseonlaunchrule>0</eraseonlaunchrule>
<EraseKey />
<AsfFrameworkConfig>
<framework-data xmlns="">
<options />
<configurations />
<files />
<documentation help="" />
<offline-documentation help="" />
<dependencies>
<content-extension eid="atmel.asf" uuidref="Atmel.ASF" version="3.52.0" />
</dependencies>
</framework-data>
</AsfFrameworkConfig>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Release' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>NDEBUG</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>$(MSBuildProjectDirectory)\..\..\libavr\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize for size (-Os)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>
<avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-std=c++26 -Wextra -Werror -mrelax -fno-exceptions -fno-rtti -fno-threadsafe-statics</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.optimization.GarbageCollectUnusedSections>True</avrgcccpp.linker.optimization.GarbageCollectUnusedSections>
<avrgcccpp.linker.miscellaneous.LinkerFlags>-mrelax -nostartfiles -Wl,--section-start=.text=0x7e00 -Wl,--defsym=tsb_app=0 -Wl,--pmem-wrap-around=32k</avrgcccpp.linker.miscellaneous.LinkerFlags>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Debug' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>DEBUG</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>$(MSBuildProjectDirectory)\..\..\libavr\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize for size (-Os)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>
<avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-std=c++26 -Wextra -Werror -mrelax -fno-exceptions -fno-rtti -fno-threadsafe-statics -gdwarf-4</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.optimization.GarbageCollectUnusedSections>True</avrgcccpp.linker.optimization.GarbageCollectUnusedSections>
<avrgcccpp.linker.miscellaneous.LinkerFlags>-mrelax -nostartfiles -Wl,--section-start=.text=0x7e00 -Wl,--defsym=tsb_app=0 -Wl,--pmem-wrap-around=32k</avrgcccpp.linker.miscellaneous.LinkerFlags>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<ItemGroup>
<Compile Include="..\..\tsb\tsb_asm.cpp">
<SubType>compile</SubType>
<Link>tsb\tsb_asm.cpp</Link>
</Compile>
</ItemGroup>
<ItemGroup>
<Folder Include="tsb" />
</ItemGroup>
<Import Project="$(AVRSTUDIO_EXE_PATH)\Vs\Compiler.targets" />
</Project>

1
libavr Submodule

Submodule libavr added at c01b19b08f

49
oracle/README.md Normal file
View File

@@ -0,0 +1,49 @@
# Oracle — the hand-written TinySafeBoot assembly
`tsb-fixedbaud.asm` is the reference implementation this port is measured
against: the **native-UART, fixed-baud** TinySafeBoot bootloader, hand-written
in AVR assembly. It is the size-and-feature bar for the port's `tsb_asm` tier.
- **Source**: <https://github.com/seedrobotics/tinysafeboot>
(`firmware_ASM/latest_stable_release/20200727-fixedbaud/main.asm`), the Seed
Robotics fixed-baud fork of Julien Thomas' TinySafeBoot.
- **License**: GPLv3 (see the header in the file). It is vendored here **only as
a reference oracle** — it is not compiled, linked, or distributed as part of
the MIT-licensed port. Mere aggregation.
## Why this variant
The user chose the fixed-baud, hardware-UART variant deliberately: it is the one
whose feature set the port must match. It fits the **complete** TSB feature set
into the 512-byte ATmega boot section:
| Feature | Oracle routine |
|---|---|
| Watchdog-reset bail straight to the app | `RESET` (WDRF check) |
| One-wire half-duplex (RX/TX shorted): RXEN/TXEN toggled per direction, TX turnaround guard | `SetRX` / `SetTX` / `TransmitByte` |
| Activation timeout read from the config page, with a lockout-proof minimum | `WRX1To` (uses `utimeoutH`) |
| 3×`@` activation knock | `ActCharRcvd` |
| Password gate; wrong byte hangs (still draining the UART) | `CheckPassword` |
| Emergency erase on password `\0` + double-confirm — wipes flash, EEPROM and the config page | `EmergencyErase` |
| Device-info block (16 bytes) | `SendDeviceInfo` / `DEVICEINFO` |
| App-flash read/write (`f`/`F`), EEPROM read/write (`e`/`E`), config read/write (`c`/`C`) | `CheckCommands` |
## Assembled size (the bar)
Assembled for the ATmega328P with `avra`:
```
avra -I /usr/share/avra tsb-fixedbaud.asm # after uncommenting .include "m328Pdef.inc"
# Code : 250 words (500 bytes) — the whole loader, all features, in the 512 B section
```
**500 bytes with every feature** — the proof that ≤512 B and full feature parity
are simultaneously reachable. The port's `tsb_asm` tier meets the same bar at
510 B in the same 512 B section, written in C++ on libavr except the two
routines whose remaining cost is the calling convention itself (the bounded rx
and the page-store loop); `tsb_tricks` needs no assembly at all at 526 B, and
`tsb_pure` stays fully idiomatic at 836 B, both in the 1 KB section.
The oracle targets 20 MHz / 33333 baud; the port targets 16 MHz / 115200 baud
(what the simavr protocol test drives). Baud and geometry differ, code size and
feature set do not.

776
oracle/tsb-fixedbaud.asm Normal file
View File

@@ -0,0 +1,776 @@
;***********************************************************************
;***********************************************************************
;***********************************************************************
; TinySafeBoot - The Universal Bootloader for AVR ATmegas
;***********************************************************************
;***********************************************************************
;***********************************************************************
;
;-----------------------------------------------------------------------
; 2020 - Version using native UART, Fixed Baud by Seed Robotics in 2020
;-----------------------------------------------------------------------
; meant for use on ATMEGA devices only (with native UART - UART0)
;
; Main differences to Regular TSB Bootloader:
; - Uses a native UART (UART0); therefore not compatible with ATTINY
; - Baud rate is fixed (set by a macro in the code). No auto bauding.
; - Disables TX while not transmitting to allow for one wire flashing
; (where RX and TX are shorted, for a multi drop bus)
; - Also works with separate RX and TX; however an external pull up
; on TX _may_ be required; alternatively you can modify the code
; in the ReceiveByte routine so that it won't disable TX.
; - FIXES:
; - situations where booting onto a bus with active communication could
; lock the autobauding feature
; - times out and boots to application code if the host stops interacting
; with the bootloader
;
;-----------------------------------------------------------------------
; Extended by Seed Robotics from 2017
;-----------------------------------------------------------------------
; Seed Robotics contributions are available from the Github
; repository github.com/seedrobotics
; The License and conditions remain as stated below, in the
; original notice.
;
;
;-----------------------------------------------------------------------
; Written in 2011-2015 by Julien Thomas
;
; This program is free software; you can redistribute it and/or
; modify it under the terms of the GNU General Public License
; as published by the Free Software Foundation; either version 3
; of the License, or (at your option) any later version.
; This program is distributed in the hope that it will be useful,
; but WITHOUT ANY WARRANTY; without even the implied warranty
; of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
; See the GNU General Public License for more details.
; You should have received a copy of the GNU General Public License
; along with this program; if not, see:
; http://www.gnu.org/licenses/
;-----------------------------------------------------------------------
;
;
;
;***********************************************************************
; OVERVIEW
;***********************************************************************
;
; TSB assembly source is organized in 4 segments (approx. line numbers)
;
; ~ 50 ... Global definitions
; ~ ... TSB for ATmegas
;
;***********************************************************************
; ADJUSTMENTS FOR INDIVIDUAL ASSEMBLY
;***********************************************************************
;
; This Sourcecode is directly compatible to: AVRASM2, GAVRASM
;
.nolist
;
;-----------------------------------------------------------------------
; SPECIFY TARGET AVR
;-----------------------------------------------------------------------
;
; Comment in and provide def.inc file for target device
;
; [Examples]
;
;.include "tn2313def.inc"
;.include "tn85def.inc"
;.include "m8515def.inc"
;.include "m168def.inc"
;.include "m161def.inc"
;.include "m324Adef.inc"
;.include "m328Pdef.inc"
;.include "tn441def.inc"
;.include "tn167def.inc"
;.include "tn861def.inc"
;.include "tn841def.inc"
;.include "tn84def.inc"
;.include "m8def.inc"
;.include "m644PAdef.inc"
;.include "m644def.inc"
;.include "tn167def.inc"
;.include "tn25def.inc"
;
; [...]
;
;
.list
;
;-----------------------------------------------------------------------
; BUILD INFO
;-----------------------------------------------------------------------
; YY = Year - MM = Month - DD = Day
.set YY = 21
.set MM = 12
.set DD = 21
;
.set BUILDSTATE = $F3 ; F1 fixed baud, pull up, derived from original (modified for fixed baud)
; F2 fixed baud, pull up, guaranteed minimum activation timeout in case of userpage data corruption
; F3 adds a CONSTANT with clock speed (Mhz) as word in the last page of memory (clock speed our defined CONSTANT)
;
;-----------------------------------------------------------------------
; TSB / TSB-INSTALLER SWITCH
;-----------------------------------------------------------------------
; 0 = Regular assembly to target address
; Other value = NOT SUPPORTED
;
.set TSBINSTALLER = 0
;
;-----------------------------------------------------------------------
; F_CPU and Baud rate setting
;-----------------------------------------------------------------------
.equ F_CPU = 20000000
.equ BAUD = 33333 ; baudrate (notice some possible wrong cals: example for 56K, it is actually 55,555, so for BAUD_PRESC give an INT result of 8, we must set BAUD to 55500)
.equ BAUD_PRESCx10 = (F_CPU * 10/16/BAUD) - 10 ; baud prescale (regular formula = F_CPU * 10/16/BAUD - 1 but we do it x10 to check the rounding)
; arredondar acima se necesssario
.if BAUD_PRESCx10 - ( (BAUD_PRESCx10 / 10) * 10 ) >= 5 ; calculate the remainder: we rely on the fact these are integer divisions. Therefore, dividing by 10, rounds DOWN in integer division
.equ BAUD_PRESC = (F_CPU/16/BAUD)
.warning "Incrementing default BAUD_PRESC formula by 1 due to rounding."
.else
.equ BAUD_PRESC = (F_CPU/16/BAUD) - 1
.warning "Using default BAUD_PRESC formula (no rounding up)"
.endif
.if BAUD_PRESC > 255
.error "ERROR: BAUD RATE TOO LOW. WE ONLY WRITE THE UBRRL REGISTER, SO UBRR MUST BE <255 FOR THIS CLOCK FREQ AND BAUD"
.endif
;***********************************************************************
; AUTO-ADJUST FOR DIFFERENT ASSEMBLY OPTIONS
;***********************************************************************
;
; Always set TINYMEGA=1 bc this code only supports ATMEGA
.equ TINYMEGA=1
.if FLASHEND > ($7fff)
.error "SORRY! DEVICES OVER 64 KB NOT SUPPORTED YET."
.exit
.endif
;-----------------------------------------------------------------------
; Workarounds for devices with renamed or missing definitions
;-----------------------------------------------------------------------
;
.ifndef SPMCSR ; SPMEN / PGERS / ...
.equ SPMCSR = SPMCR
.endif
.ifndef MCUSR ; PORF / EXTRF / BORF / WDRF
.equ MCUSR = MCUCSR
.endif
; Detect Attiny441/841 to amend missing pagesize and apply 4-page mode
.set FOURPAGES = 0
.if ((SIGNATURE_000 == $1E) && (SIGNATURE_002 == $15) && (SIGNATURE_001 == $92))
.equ PAGESIZE = 32
.set FOURPAGES = 1
.message "ATTINY441: 4-PAGE-ERASE MODE"
.endif
.if ((SIGNATURE_000 == $1E) && (SIGNATURE_002 == $15) && (SIGNATURE_001 == $93))
.equ PAGESIZE = 32
.set FOURPAGES = 1
.message "ATTINY841: 4-PAGE-ERASE MODE"
.endif
;-----------------------------------------------------------------------
; Universal Constants and Registers
;-----------------------------------------------------------------------
.equ REQUEST = '?' ; request / answer / go on
.equ CONFIRM = '!' ; confirm / attention
; Current bootloader date coded into 16-bit number
.equ BUILDDATE = YY * 512 + MM * 32 + DD
; Other
.equ INFOLEN = 8 ; *Words* of Device Info
.equ BUFFER = SRAM_START
; Registers (in use by TSB-Firmware and TSB-Installer for ATtinys)
.def avecl = r4 ; application vector temp low
.def avech = r5 ; application vector temp high
.def tmp1 = r16 ; these are
.def tmp2 = r17 ; universal
.def tmp3 = r18 ; temporary
.def tmp4 = r19 ; registers
.def bcnt = r20 ; page bytecounter
.def cntr1 = r21 ; timeout counter
.def rxen = r22 ; check if RX enabled (meaning TX disabled)
.def utimeoutH = r23 ; user timeout High byte
; special purpose registers start at R26
;
;
;***********************************************************************
;***********************************************************************
;***********************************************************************
; START OF TSB FOR ATMEGAS
;***********************************************************************
;***********************************************************************
;***********************************************************************
;
; TSB for ATmegas is always coded directly to target address.
.if TINYMEGA == 1
.message "ASSEMBLY OF TSB FOR ATMEGA"
.equ BOOTSTART = (FLASHEND+1)-256 ; = 512 Bytes
.equ LASTPAGE = BOOTSTART - PAGESIZE ; = 1 page below TSB!
.org BOOTSTART
RESET:
cli
in tmp4, MCUSR ; check reset condition
sbrc tmp4, WDRF ; in case of a Watchdog reset
rjmp APPJUMP ; immediately leave TSB
ldi tmp1, low (RAMEND) ; write ramend low
out SPL, tmp1 ; into SPL (stackpointer low)
.ifdef SPH
ldi tmp1, high(RAMEND) ; write ramend high for ATtinys
out SPH, tmp1 ; with SRAM > 256 bytes
.message "PROVIDING FOR STACK BIGGER THAN 256 BYTES"
.endif
.ifndef DDRD2
.equ DDRD2 = DDD2
.endif
;-----------------------------------------------------------------------
; ACTIVATION CHECK
;-----------------------------------------------------------------------
; Configure UART; no autobauding in this version
ldi tmp1,BAUD_PRESC ; load baud prescale
sts UBRR0L,tmp1 ; set baud prescale
; ldi tmp2,HIGH(bpsc) ; save code by not loading UBBRH
;sts UBRRH,tmp2 ; to UBRR0
;ldi tmp2,( (1<<RXEN0) ) ; enable transmiter and receiver
;sts UCSR0B,tmp2
; Enable Pull up on Port D2 (PD2)
cbi DDRD, DDRD2
sbi PORTD, PORTD2
; we will enable RNEN/TXEN in the ReceiveByte and TransmitByte routines
rcall ZtoLASTPAGE ; set Z to start'o'LASTPAGE
adiw zl, 2 ; skip first 2 bytes (APPJUMP)
lpm utimeoutH, z+ ; load TIMEOUT byte and store for use in RX byte timeout
ori utimeoutH, (F_CPU / 1000000); prevent bootloader lockout due if it gets an invalid (to small) timeout setting
; this ensures value is at least the clock rate, which shoudl give about 40ms
clr tmp2 ; apparently at times this is not set to 0 on boot? (seen while in debugWire)
clr rxen ; same as above
WRX1To:
; we'll check the X register which is where ReceibeByte controls the timeout
; the overall timeout of receive byte is the timeout set by the user
; therefore, if we get characters while X> 0 we're attempting to activate bootloader;
; if not, if X=0 we timedout and go to app start
rcall ReceiveByte
brcs WRX2To ; if X got to 0 (i.e. carry set), assume we timed out
cpi tmp1, '@' ; did we get an activation char = "@"
breq ActCharRcvd
WRX2To:
rjmp APPJUMP ; not an activation char goto APPJUMP in LASTPAGE
ActCharRcvd:
inc tmp2
cpi tmp2, 3
brne WRX1To ; branch if not yet at 3;
; otherwise fall through to password check
;-----------------------------------------------------------------------
; CHECK PASSWORD / EMERGENCY ERASE
;-----------------------------------------------------------------------
; we use the user timeout (utimeoutH) register for COMM timeout
; when we don't get valid data
; increase this value to a fixed one now, to cope
; with cases where the user timeout is set so low that we don't have time to
; do anything
ldi utimeoutH, (F_CPU / 78500) ; this should result in 255 for 20Mhz and proportionally
; less for lower Clocks, so that we get the same time approx. 2.4sec
CheckPassword:
chpw0: ser tmp4 ; tmp4 = 255 enables comparison
chpw1: lpm tmp3, z+ ; load pw character from Z
and tmp3, tmp4 ; if tmp4 = 0 disables comparison, for wrong password scenarios
cpi tmp3, 255 ; byte value 255 indicates
breq chpwx ; end of password -> success
chpw2: rcall Receivebyte ; else receive next character
cpi tmp1, 0 ; rxbyte = 0 will branch
breq chpwee ; to confirm emergency erase
cp tmp1, tmp3 ; compare password with rxbyte
breq chpw0 ; if equal check next character
clr tmp4 ; tmp4 = 0 to loop forever
rjmp chpw1 ; and smoothen power profile
chpwee:
; Fix for ISSUE #1: only check for Emergency Erase if we haven't
; gotten a wrong password; if we got a wrong password
; then we should stay in loop and not escape to Emergency
; Erase
cpi tmp4, 0 ; if tmp4=0 we are set to loop forever
breq chpw1
rcall RequestConfirm ; request confirm
brts chpa ; not confirmed, leave
rcall RequestConfirm ; request 2nd confirm
brts chpa ; can't be mistake now
rcall EmergencyErase ; go, emergency erase!
rjmp Mainloop
chpa:
rjmp APPJUMP ; start application
chpwx:
; rjmp SendDeviceInfo ; go on to SendDeviceInfo
;-----------------------------------------------------------------------
; SEND DEVICEINFO
;-----------------------------------------------------------------------
SendDeviceInfo:
ldi zl, low (DEVICEINFO*2) ; load address of deviceinfo
ldi zh, high(DEVICEINFO*2) ; low and highbyte
ldi bcnt, INFOLEN*2
rcall SendFromFlash
;-----------------------------------------------------------------------
; MAIN LOOP TO RECEIVE AND EXECUTE COMMANDS
;-----------------------------------------------------------------------
Mainloop:
clr zl ; clear Z pointer
clr zh ; which is frequently used
rcall SendConfirm ; send CONFIRM via RS232
rcall Receivebyte ; receive command via RS232
rcall CheckCommands ; check command letter
rjmp Mainloop ; and loop on
;-----------------------------------------------------------------------
; CHANGE USER DATA IN LASTPAGE
;-----------------------------------------------------------------------
ChangeSettings:
rcall GetNewPage ; get new LASTPAGE contents
brtc ChangeS0 ; from Host (if confirmed)
ret
ChangeS0:
rcall ZtoLASTPAGE ; re-write LASTPAGE
rcall EraseFlashPage
rcall WritePage ; erase and write LASTPAGE
;-----------------------------------------------------------------------
; SEND USER DATA FROM LASTPAGE
;-----------------------------------------------------------------------
ControlSettings:
rcall ZtoLASTPAGE ; point to LASTPAGE
; rcall SendPageFromFlash
;-----------------------------------------------------------------------
; SEND DATA FROM FLASH MEMORY
;-----------------------------------------------------------------------
SendPageFromFlash:
ldi bcnt, low (PAGESIZE*2) ; whole Page to send
SendFromFlash:
rcall SPMwait ; (re)enable RWW read access
lpm tmp1, z+ ; read directly from flash
rcall Transmitbyte ; and send out to RS232
dec bcnt ; bcnt is number of bytes
brne SendFromFlash
ret
;-----------------------------------------------------------------------
; READ APPLICATION FLASH
;-----------------------------------------------------------------------
; read and transmit application flash area (pagewise)
ReadAppFlash:
RAF0:
rcall RwaitConfirm
brts RAFx
rcall SendPageFromFlash
RAF1:
cpi zl, low (LASTPAGE*2) ; count up to last byte
brne RAF0 ; below LASTPAGE
cpi zh, high(LASTPAGE*2)
brne RAF0
RAFx:
ret
;-----------------------------------------------------------------------
; WRITE APPLICATION FLASH
;-----------------------------------------------------------------------
; Write Appflash pagewise, don't modify anything for ATmegas
WriteAppFlash:
rcall EraseAppFlash ; Erase whole app flash
Flash2:
rcall GetNewPage ; get next page from host
brts FlashX ; stop on user's behalf
Flash3:
rcall WritePage ; write page data into flash
Flash4:
cpi zh, high(LASTPAGE*2-1) ; end of available Appflash?
brne Flash2 ; if Z reached last location
cpi zl, low (LASTPAGE*2-1) ; then we are finished
brne Flash2 ; else go on
FlashX:
ret ; we're already finished!
;-----------------------------------------------------------------------
; WRITE FLASH PAGE FROM BUFFER, VERIFYING AND VERIFY-ERROR-HANDLING
;-----------------------------------------------------------------------
WritePage:
rcall YtoBUFFER ; Y=BUFFER, bcnt=PAGESIZE*2
WrPa1:
ld r0, y+ ; fill R0/R1 with word
ld r1, y+ ; from buffer position Y / Y+1
ldi tmp1, 0b00000001 ; set only SPMEN in SPMCSR
out SPMCSR, tmp1 ; to activate page buffering
spm ; store word in page buffer
adiw zl, 2 ; and forward to next word
subi bcnt, 2
brne WrPa1
; Z = start of next page now
subi zl, low (PAGESIZE*2) ; point back Z to
sbci zh, high(PAGESIZE*2) ; start of current page
; Z = back on current page's start
WrPa2:
ldi tmp1, 0b00000101 ; enable PRWRT + SPMEN
out SPMCSR, tmp1 ; in SPMCSR
spm ; write whole page to flash
WrPa3:
in tmp1, SPMCSR ; wait for flash write finished
sbrc tmp1, 0 ; skip if SPMEN (bit0) cleared
rjmp WrPa3 ; ITS BEEN WRITTEN
subi zl, low (-PAGESIZE*2) ; same effect as
sbci zh, high(-PAGESIZE*2) ; Z = Z + PAGESIZE*2
ret
;-----------------------------------------------------------------------
; CHECK COMMANDS
;-----------------------------------------------------------------------
CheckCommands:
cpi tmp1, 'c' ; read LASTPAGE
breq ControlSettings
cpi tmp1, 'C' ; write LASTPAGE
breq ChangeSettings
cpi tmp1, 'f' ; read Appflash
breq ReadAppFlash
cpi tmp1, 'F' ; write Appflash
breq WriteAppFlash
cpi tmp1, 'e' ; read EEPROM
breq EepromRead
cpi tmp1, 'E' ; write EEPROM
breq EEpromWrite
rjmp APPJUMP ; else start application
;-----------------------------------------------------------------------
; EEPROM READ/WRITE ACCESS
;-----------------------------------------------------------------------
EepromWrite:
EEWr0:
rcall GetNewPage ; get EEPROM datablock
brts EERWFx ; or abort on host's demand
EEWr1:
rcall YtoBUFFER ; Y = Buffer and Bcnt = blocksize
EEWr2:
ld tmp1, y+ ; read EEPROM byte from buffer
rcall EEWriteByte
dec bcnt ; count down block byte counter
brne EEWr2 ; loop on if block not finished
rjmp EeWr0
;-----------------------------------------------------------------------
EEpromRead:
EeRe1:
rcall RwaitConfirm ; wait to confirm
brts EERWFx ; else we are finished
ldi bcnt, low(PAGESIZE*2) ; again PAGESIZE*2 is blocksize
EERe2:
out EEARL, zl ; current EEPROM address low
.ifdef EEARH
out EEARH, zh ; current EEPROM address high
.endif
sbi EECR, 0 ; set EERE - EEPROM read enable
in tmp1, EEDR ; read byte from current address
rcall Transmitbyte ; send out to RS232
adiw zl,1 ; count up EEPROM address
dec bcnt ; count down block byte counter
brne EERe2 ; loop on if block not finished
rjmp EERe1
EERWFx:
ret
;-----------------------------------------------------------------------
EEWriteByte:
out EEDR, tmp1 ; write to EEPROM data register
out EEARL, zl ; current EEPROM address low
.ifdef EEARH
out EEARH, zh ; high EEARH for some attinys
.endif
sbi EECR, 2 ; EEPROM master prog enable
sbi EECR, 1 ; EEPE initiate prog cycle
EeWB:
sbic EECR, 1 ; wait write cycle to complete
rjmp EeWB ; before we can go on
adiw zl,1 ; count up EEPROM address
ret
;-----------------------------------------------------------------------
; GET NEW PAGE
;-----------------------------------------------------------------------
GetNewPage:
rcall RequestConfirm ; check for Confirm
brts GNPx ; abort if not confirmed
GNP0:
rcall YtoBUFFER ; Y = BUFFER, bcnt = PAGESIZE*2
GNP1:
rcall ReceiveByte ; receive serial byte
st y+, tmp1 ; and store in buffer
dec bcnt ; until full page loaded
brne GNP1 ; loop on
GNPx:
ret ; finished
;-----------------------------------------------------------------------
; REQUEST TO CONFIRM / AWAIT CONFIRM COMMAND
;-----------------------------------------------------------------------
RequestConfirm:
ldi tmp1, REQUEST ; send request character
rcall Transmitbyte ; prompt to confirm (or not)
RwaitConfirm:
rcall ReceiveByte ; get host's reply
clt ; set T=0 for confirmation
cpi tmp1, CONFIRM ; if host HAS sent CONFIRM
breq RCx ; return with the T=0
set ; else set T=1 (NOT CONFIRMED)
RCx:
ret ; whether confirmed or not
;-----------------------------------------------------------------------
; FLASH ERASE TOP-TO-BOTTOM ( (BOOTSTART-1) ... $0000)
;-----------------------------------------------------------------------
EraseAppFlash:
rcall ZtoLASTPAGE ; point Z to LASTPAGE, directly
EAF0:
subi zl, low (PAGESIZE*2)
sbci zh, high(PAGESIZE*2)
rcall EraseFlashPage
brne EAF0 ; until first page reached
EAFx: ret ; and leave with Z = $0000
;-----------------------------------------------------------------------
; EMERGENCY ERASE OF FLASH / EEPROM / USERDATA
;-----------------------------------------------------------------------
EmergencyErase:
rcall EraseAppFlash ; erase Application Flash
ser tmp1 ; byte value for EEPROM writes
EEE0:
rcall EEWriteByte ; write EEPROM byte, Z = Z + 1
cpi zh, high(EEPROMEND+1)+2 ; EEPROMEND
brne EEE0 ; and loop on until finished
rcall ZtoLASTPAGE ; LASTPAGE is to be erased
; rcall EraseFlashPage
;-----------------------------------------------------------------------
; ERASE ONE FLASH PAGE
;-----------------------------------------------------------------------
EraseFlashPage:
ldi tmp1, 0b00000011 ; enable PGERS + SPMEN
out SPMCSR, tmp1 ; in SPMCSR and erase current
spm ; page by SPM (MCU halted)
; Waiting for SPM to be finished is *obligatory* on ATmegas!
SPMwait:
in tmp1, SPMCSR
sbrc tmp1, 0 ; wait previous SPMEN
rjmp SPMwait
ldi tmp1, 0b00010001 ; set RWWSRE and SPMEN
out SPMCSR, tmp1
spm
ret
;-----------------------------------------------------------------------
; OTHER SUBROUTINES
;-----------------------------------------------------------------------
YtoBUFFER:
ldi yl, low (BUFFER) ; reset pointer
ldi yh, high(BUFFER) ; to programming buffer
ldi bcnt, low(PAGESIZE*2) ; and often needed
ret
;-----------------------------------------------------------------------
ZtoLASTPAGE:
ldi zl, low (LASTPAGE*2) ; reset Z to LASTPAGE start
ldi zh, high(LASTPAGE*2)
ret
;-----------------------------------------------------------------------
; RS232 RECEIVE BYTE
;-----------------------------------------------------------------------
; uses: tmp1 (received data byte), cntr1 (for timeout)
; also uses utimeoutH which holds the default timeout defined by the user
; and X which is actually used to count down
SetRX:
ldi tmp1,(1<<RXEN0) ; enable receiver (Transmitter disabled)
sts UCSR0B,tmp1
ser rxen
ReceiveByte:
sbrs rxen, 0
rjmp SetRX
; outer counter
mov xh, utimeoutH
;ldi xl, 128
ReceiveByteShortTimeout:
ser cntr1 ; inner counter reset
ReceiveByteShortTimeout1:
lds tmp1, UCSR0A ; load UART status register A
sbrc tmp1, RXC0 ; if not RXComplete, skip
rjmp LoadRXByte
dec cntr1 ; if counter not zero
brne ReceiveByteShortTimeout1 ; cycle again; else fall through
sbiw xl, 1 ; dec outter counter
brcc ReceiveByteShortTimeout ; continue of outter counetr still active
;ret ;
LoadRXByte:
lds tmp1, UDR0 ; load received character even if RXC is not set
ret ; (it loads 0 and UDR FIFO should recover for next char)
;-----------------------------------------------------------------------
; RS232 SEND CONFIRM CHARACTER
;-----------------------------------------------------------------------
SendConfirm:
ldi tmp1, CONFIRM
rjmp Transmitbyte
;-----------------------------------------------------------------------
; RS232 TRANSMIT BYTE
;-----------------------------------------------------------------------
; uses: tmp1 (transmit byte will be shifted out), tmp2 (bitcounter)
;
SetTX:
ldi tmp2,(1<<TXEN0) ; enable transmitter (Receiver disabled)
sts UCSR0B,tmp2
clr rxen
; wait some guard time to allow receiving devices ot transition
; from TX t RX state
ser cntr1 ; inner counter reset
SetTXShortTimeout:
nop
dec cntr1 ; if counter not zero
brne SetTXShortTimeout ; cycle again; else fall through
TransmitByte:
sbrc rxen, 0
rjmp SetTX
; no need to wait for UDRE bc we will wait for TXC on
; every char transmitted. TXC occurs later that UDRE
; so UDRE should be asserted when TXC asserts
sts UDR0, tmp1
WaitForTXC:
lds tmp2, UCSR0A ; wait for TXC (and not UDRE)
sbrs tmp2, TXC0 ; bc after this char we may transition
rjmp WaitForTXC ; to receiving chars and we want to make sure we get a clean transition
; we need to write a 1 to clear the TXC flag; otherwise the flag won't clear
sts UCSR0A, tmp2 ; tmp2 should contain an asserted TXC bit
ret
;-----------------------------------------------------------------------
; ATMEGA APPJUMP = SIMPLE JUMP TO $0000 (ORIGINAL RESET VECTOR)
;-----------------------------------------------------------------------
; Boot Reset Vector (BOOTRST) must be activated for TSB on ATmegas.
; After timeout or executing commands, TSB for ATmegas will simply
; handover to the App by a (relative or absolute) jump to $0000.
APPJUMP:
rcall SPMwait ; make sure everything's done
.if FLASHEND >= ($1fff)
jmp $0000 ; absolute jump
.else
rjmp $0000 ; relative jump
.endif
DEVICEINFO:
.message "DEVICE INFO BLOCK FOR ATMEGA"
.db "TSB", low (BUILDDATE), high (BUILDDATE), BUILDSTATE
.db SIGNATURE_000, SIGNATURE_001, SIGNATURE_002, low (PAGESIZE)
.dw BOOTSTART-PAGESIZE
.dw EEPROMEND
.db $AA, $AA
;-----------------------------------------------------------------------
; DEVICE INFO BLOCK = PERMANENT DATA
;-----------------------------------------------------------------------
; set last word with the clock speed
.org FLASHEND
.dw (F_CPU/1000000)
//.message "SAVING CLOCK SPEED IN LAST BYTE AS " (F_CPU/1000000) " Mhz"
.message "ASSEMBLY OF TSB FOR ATMEGA SUCCESSFULLY FINISHED!"
.endif ; closing TSB for ATmega sourcecode;
;***********************************************************************
; END OF TSB FOR ATMEGAS
;***********************************************************************
.exit
;***********************************************************************
;***********************************************************************
;***********************************************************************
; END OF CONDITIONAL ASSEMBLY SOURCE OF TSB FOR ATTINYS AND ATMEGAS
;***********************************************************************
;***********************************************************************
;***********************************************************************

436
pureboot/CMakeLists.txt Normal file
View File

@@ -0,0 +1,436 @@
# pureboot as a consumable CMake unit: the per-chip geometry, the default baud
# ladder, and pureboot_add_loader() — the one way a loader target is created.
# A downstream project brings its usual libavr setup (the `libavr` target and
# the LIBAVR_MCU toolchain preset), adds this directory, and states its
# deployment; every argument is optional (README.md):
#
# add_subdirectory(bootloader/pureboot)
# pureboot_add_loader(myboot CLOCK 1000000 SERIAL software TX pb1 RX pb5)
# Per-family geometry, deployment defaults, and the linker wrap the PC modulo
# needs. The slot is 512 bytes on every chip. The USART flags mirror the
# hardware inventory the loader's own static asserts check — the plain 644 is
# the x4 family's one single-USART die (Atmel-2593).
set(_pb_has_usart 1)
set(_pb_has_usart1 0)
if(LIBAVR_MCU MATCHES "^attiny13a?$")
set(_pb_flash 1024)
set(_pb_wrap "")
set(_pb_page 32)
set(_pb_hz 9600000)
set(_pb_eeprom 64)
set(_pb_has_usart 0)
elseif(LIBAVR_MCU STREQUAL "attiny25")
set(_pb_flash 2048)
set(_pb_wrap "")
set(_pb_page 32)
set(_pb_hz 8000000)
set(_pb_eeprom 128)
set(_pb_has_usart 0)
elseif(LIBAVR_MCU STREQUAL "attiny45")
set(_pb_flash 4096)
set(_pb_wrap "")
set(_pb_page 64)
set(_pb_hz 8000000)
set(_pb_eeprom 256)
set(_pb_has_usart 0)
elseif(LIBAVR_MCU STREQUAL "attiny85")
set(_pb_flash 8192)
set(_pb_wrap -Wl,--pmem-wrap-around=8k)
set(_pb_page 64)
set(_pb_hz 8000000)
set(_pb_eeprom 512)
set(_pb_has_usart 0)
elseif(LIBAVR_MCU MATCHES "^atmega48(a|p|pa)?$")
set(_pb_flash 4096)
set(_pb_wrap "")
set(_pb_page 64)
set(_pb_hz 16000000)
set(_pb_eeprom 256)
elseif(LIBAVR_MCU MATCHES "^atmega8a?$" OR LIBAVR_MCU MATCHES "^atmega88(a|p|pa)?$")
set(_pb_flash 8192)
set(_pb_wrap -Wl,--pmem-wrap-around=8k)
set(_pb_page 64)
set(_pb_hz 16000000)
set(_pb_eeprom 512)
elseif(LIBAVR_MCU MATCHES "^atmega16a?$" OR LIBAVR_MCU MATCHES "^atmega168(a|p|pa)?$")
set(_pb_flash 16384)
set(_pb_wrap -Wl,--pmem-wrap-around=16k)
set(_pb_page 128)
set(_pb_hz 16000000)
set(_pb_eeprom 512)
elseif(LIBAVR_MCU MATCHES "^atmega164(a|p|pa)$")
set(_pb_flash 16384)
set(_pb_wrap -Wl,--pmem-wrap-around=16k)
set(_pb_page 128)
set(_pb_hz 16000000)
set(_pb_eeprom 512)
set(_pb_has_usart1 1)
elseif(LIBAVR_MCU MATCHES "^atmega32a?$" OR LIBAVR_MCU MATCHES "^atmega328p?$")
set(_pb_flash 32768)
set(_pb_wrap -Wl,--pmem-wrap-around=32k)
set(_pb_page 128)
set(_pb_hz 16000000)
set(_pb_eeprom 1024)
elseif(LIBAVR_MCU MATCHES "^atmega324(a|p|pa)$")
set(_pb_flash 32768)
set(_pb_wrap -Wl,--pmem-wrap-around=32k)
set(_pb_page 128)
set(_pb_hz 16000000)
set(_pb_eeprom 1024)
set(_pb_has_usart1 1)
elseif(LIBAVR_MCU MATCHES "^atmega644(a|p|pa)?$")
# 64 KiB is exactly the 16-bit byte space, so plain LPM still reaches
# everything and the wire stays byte-addressed. The plain 644 is the
# family's one single-USART die.
set(_pb_flash 65536)
set(_pb_wrap -Wl,--pmem-wrap-around=64k)
set(_pb_page 256)
set(_pb_hz 16000000)
set(_pb_eeprom 2048)
if(NOT LIBAVR_MCU STREQUAL "atmega644")
set(_pb_has_usart1 1)
endif()
elseif(LIBAVR_MCU MATCHES "^atmega1284p?$")
# 128 KiB: wire addresses are words, reads go through ELPM, and the PC's
# modulo wrap exceeds what --pmem-wrap-around models.
set(_pb_flash 131072)
set(_pb_wrap "")
set(_pb_page 256)
set(_pb_hz 16000000)
set(_pb_eeprom 4096)
set(_pb_has_usart1 1)
else()
message(FATAL_ERROR "pureboot: no geometry for ${LIBAVR_MCU}")
endif()
set(_pb_slot 512)
math(EXPR _pb_base "${_pb_flash} - ${_pb_slot}")
math(EXPR _pb_base_hex "${_pb_base}" OUTPUT_FORMAT HEXADECIMAL)
# Patched-vector chips hand over through the trampoline word below the slot,
# which is also the slot's own last word — their budget is slot − 2.
if(LIBAVR_MCU MATCHES "^atmega" AND NOT LIBAVR_MCU MATCHES "^atmega48")
set(_pb_app 0)
set(_pb_limit ${_pb_slot})
else()
math(EXPR _pb_app "${_pb_base} - 2")
math(EXPR _pb_limit "${_pb_slot} - 2")
endif()
# The pins each USART owns. A bit-banged link deployed on them has to release
# that USART before it can drive the line, and those instructions are the one
# way the choice of pins moves the image — so a size matrix needs them as an
# axis even though pins are otherwise immediate operands. Uniform across every
# mega libavr covers: USART0 (the classics' un-numbered USART included) on
# PD0/PD1, USART1 on PD2/PD3.
set(_pb_usart0_rx pd0)
set(_pb_usart0_tx pd1)
set(_pb_usart1_rx pd2)
set(_pb_usart1_tx pd3)
# simavr names its cores after the base dies; the A revisions run on them
# (the 644PA on the 644P core).
set(_pb_sim_mcu ${LIBAVR_MCU})
if(LIBAVR_MCU MATCHES "^atmega(8|16|32|48|88|164|168|644)a$")
string(REGEX REPLACE "a$" "" _pb_sim_mcu ${LIBAVR_MCU})
elseif(LIBAVR_MCU STREQUAL "atmega644pa")
set(_pb_sim_mcu atmega644p)
endif()
# Where SRAM begins: the classic megas keep it right after the plain I/O
# registers, the x8/x4 generations push it past their extended I/O file, and
# the tinies match the classics. An autobaud loader keeps its measured unit
# in GPIOR2:GPIOR1 wherever the chip has the pair (data 0x32 on the
# t25/45/85, 0x4A from the x8 generation on) and as the first RAM object at
# SRAM start where it does not (the t13s and classic megas). The host reads
# whichever home applies (pureboot.py's geometry), and the unit-position
# test holds the image to the same split.
if(LIBAVR_MCU MATCHES "^atmega(8|16|32)a?$")
set(_pb_ram 0x60)
set(_pb_unit_gpior "")
elseif(LIBAVR_MCU MATCHES "^atmega")
set(_pb_ram 0x100)
set(_pb_unit_gpior 0x4A)
elseif(LIBAVR_MCU MATCHES "^attiny13")
set(_pb_ram 0x60)
set(_pb_unit_gpior "")
else()
set(_pb_ram 0x60)
set(_pb_unit_gpior 0x32)
endif()
# The function runs in its caller's scope, so everything it needs crosses
# scopes as global properties.
set_property(GLOBAL PROPERTY PUREBOOT_BASE_HEX ${_pb_base_hex})
set_property(GLOBAL PROPERTY PUREBOOT_APP ${_pb_app})
set_property(GLOBAL PROPERTY PUREBOOT_WRAP "${_pb_wrap}")
set_property(GLOBAL PROPERTY PUREBOOT_DEFAULT_HZ ${_pb_hz})
set_property(GLOBAL PROPERTY PUREBOOT_HAS_USART ${_pb_has_usart})
set_property(GLOBAL PROPERTY PUREBOOT_HAS_USART1 ${_pb_has_usart1})
set_property(GLOBAL PROPERTY PUREBOOT_USART0_RX ${_pb_usart0_rx})
set_property(GLOBAL PROPERTY PUREBOOT_USART0_TX ${_pb_usart0_tx})
set_property(GLOBAL PROPERTY PUREBOOT_USART1_RX ${_pb_usart1_rx})
set_property(GLOBAL PROPERTY PUREBOOT_USART1_TX ${_pb_usart1_tx})
# The port's own build (tests, the size matrix) reads the geometry from the
# parent scope; a downstream consumer gets the same variables for free.
set(PUREBOOT_BASE_HEX ${_pb_base_hex} PARENT_SCOPE)
set(PUREBOOT_PAGE ${_pb_page} PARENT_SCOPE)
set(PUREBOOT_SLOT ${_pb_slot} PARENT_SCOPE)
set(PUREBOOT_LIMIT ${_pb_limit} PARENT_SCOPE)
set(PUREBOOT_EEPROM ${_pb_eeprom} PARENT_SCOPE)
set(PUREBOOT_DEFAULT_HZ ${_pb_hz} PARENT_SCOPE)
set(PUREBOOT_RAM_START ${_pb_ram} PARENT_SCOPE)
set(PUREBOOT_UNIT_GPIOR "${_pb_unit_gpior}" PARENT_SCOPE)
set(PUREBOOT_HAS_USART ${_pb_has_usart} PARENT_SCOPE)
set(PUREBOOT_HAS_USART1 ${_pb_has_usart1} PARENT_SCOPE)
set(PUREBOOT_SIM_MCU ${_pb_sim_mcu} PARENT_SCOPE)
set(PUREBOOT_USART0_RX ${_pb_usart0_rx} PARENT_SCOPE)
set(PUREBOOT_USART0_TX ${_pb_usart0_tx} PARENT_SCOPE)
set(PUREBOOT_USART1_RX ${_pb_usart1_rx} PARENT_SCOPE)
set(PUREBOOT_USART1_TX ${_pb_usart1_tx} PARENT_SCOPE)
# The rates a default may pick, fastest first.
set_property(GLOBAL PROPERTY PUREBOOT_BAUD_LADDER 115200 57600 38400 19200 9600)
# Whether <baud> is reachable from <clock> within 2.5 %, by the same
# best-of-U2X-and-plain divisor search libavr's solve_baud runs, so a build
# never trips the compile-time error it is checked against. A software build
# also needs the polled receiver's 100-cycles-a-bit floor: at low clocks the
# U2X divisor reaches rates the bit-banged sampler cannot.
function(pureboot_baud_feasible clock baud software outvar)
set(${outvar} 0 PARENT_SCOPE)
math(EXPR _cycles "${clock} / ${baud}")
if(software AND _cycles LESS 100)
return()
endif()
foreach(divisor 8 16)
math(EXPR _step "${divisor} * ${baud}")
math(EXPR _n "(${clock} + ${_step} / 2) / ${_step}")
if(_n LESS 1 OR _n GREATER 4096)
continue()
endif()
math(EXPR _actual "${clock} / (${divisor} * ${_n})")
math(EXPR _delta "${_actual} - ${baud}")
if(_delta LESS 0)
math(EXPR _delta "-(${_delta})")
endif()
math(EXPR _error_bp "${_delta} * 10000 / ${baud}")
if(_error_bp LESS_EQUAL 250)
set(${outvar} 1 PARENT_SCOPE)
return()
endif()
endforeach()
endfunction()
# The fastest ladder rate the clock reaches.
function(pureboot_default_baud clock software outvar)
get_property(_ladder GLOBAL PROPERTY PUREBOOT_BAUD_LADDER)
foreach(baud ${_ladder})
pureboot_baud_feasible(${clock} ${baud} ${software} _ok)
if(_ok)
set(${outvar} ${baud} PARENT_SCOPE)
return()
endif()
endforeach()
message(FATAL_ERROR "pureboot: no standard baud rate fits a ${clock} Hz clock within 2.5 % "
"— pass BAUD <rate> to deploy a non-standard one")
endfunction()
# pureboot_add_loader(<name> [CLOCK <hz>] [BAUD <bd>]
# [SERIAL auto|hardware|software|autobaud] [USART <n>]
# [RX <pin>] [TX <pin>] [TIMEOUT <s>] [OSCCAL <byte>]
# [HALF_DUPLEX])
#
# The loader target plus its flashable images (<name>.hex for a programmer,
# <name>.bin for --update-loader). The resolved deployment is stamped on the
# target as PUREBOOT_HZ / PUREBOOT_BAUD / PUREBOOT_LINK (the link spelled
# usart0, usart1, or sw:<RX>,<TX> with a trailing @<n> where those pins are a
# USART's own) — what a test harness speaks to it with.
#
# HALF_DUPLEX is the one-wire deployment, per backend: on the hardware USART
# it enables the library's .half_duplex turn-around (RXD and TXD tied
# together off-chip); on a software or autobaud link it puts both directions
# on the RX pin — the same thing RX == TX spells directly.
#
# SERIAL autobaud measures the host's bit timing at run time, so the image
# carries no clock and no baud: CLOCK and BAUD are not build parameters there,
# and one binary per chip serves every F_CPU and every rate. The stamped
# PUREBOOT_HZ/PUREBOOT_BAUD then record what a harness should *drive* it at,
# not what it was built for.
#
# OSCCAL bakes a measured oscillator trim into the loader (README.md: the
# RC-oscillator deployment answer): the byte is written at the top of run(),
# so every reset path — the watchdog hand-over included — runs on the
# corrected clock. Orthogonal to the backend: an autobaud build may carry it
# purely for the application's benefit, its own link being clock-free. No
# value, no code.
function(pureboot_add_loader name)
cmake_parse_arguments(PB "HALF_DUPLEX" "CLOCK;BAUD;SERIAL;USART;RX;TX;TIMEOUT;OSCCAL" "" ${ARGN})
if(PB_UNPARSED_ARGUMENTS)
message(FATAL_ERROR "pureboot_add_loader(${name}): unknown arguments ${PB_UNPARSED_ARGUMENTS}")
endif()
get_property(_hz GLOBAL PROPERTY PUREBOOT_DEFAULT_HZ)
get_property(_base_hex GLOBAL PROPERTY PUREBOOT_BASE_HEX)
get_property(_app GLOBAL PROPERTY PUREBOOT_APP)
get_property(_wrap GLOBAL PROPERTY PUREBOOT_WRAP)
get_property(_usart GLOBAL PROPERTY PUREBOOT_HAS_USART)
get_property(_usart1 GLOBAL PROPERTY PUREBOOT_HAS_USART1)
if(NOT PB_CLOCK)
set(PB_CLOCK ${_hz})
endif()
if(NOT PB_TIMEOUT)
set(PB_TIMEOUT 8)
endif()
if(NOT PB_SERIAL)
set(PB_SERIAL auto)
endif()
if(DEFINED PB_USART AND NOT PB_SERIAL MATCHES "^(auto|hardware)$")
message(FATAL_ERROR "pureboot_add_loader(${name}): USART ${PB_USART} contradicts SERIAL ${PB_SERIAL}")
endif()
if(DEFINED PB_USART)
set(PB_SERIAL hardware)
elseif(PB_SERIAL STREQUAL "hardware")
set(PB_USART 0)
endif()
set(_serial_defines "")
if(PB_SERIAL STREQUAL "hardware")
if(PB_USART EQUAL 1 AND NOT _usart1)
message(FATAL_ERROR "pureboot_add_loader(${name}): ${LIBAVR_MCU} has no USART1")
elseif(NOT _usart)
message(FATAL_ERROR "pureboot_add_loader(${name}): ${LIBAVR_MCU} has no hardware USART")
endif()
set(_serial_defines PUREBOOT_USART=${PB_USART})
if(PB_HALF_DUPLEX)
list(APPEND _serial_defines PUREBOOT_HALF_DUPLEX)
endif()
set(_link usart${PB_USART})
else()
if(PB_SERIAL STREQUAL "auto")
if(_usart AND (PB_RX OR PB_TX))
message(WARNING "pureboot_add_loader(${name}): RX/TX apply to the software UART, "
"which auto does not pick on ${LIBAVR_MCU} — SERIAL software to force it")
endif()
if(_usart)
set(_link usart0)
if(PB_HALF_DUPLEX)
set(_serial_defines PUREBOOT_HALF_DUPLEX)
endif()
else()
set(PB_SERIAL software)
endif()
endif()
if(PB_SERIAL MATCHES "^(software|autobaud)$")
if(NOT PB_RX)
set(PB_RX pb0)
endif()
if(PB_HALF_DUPLEX)
# One-wire: both directions on the RX pin. RX == TX spells
# the same deployment directly.
if(PB_TX AND NOT PB_TX STREQUAL PB_RX)
message(FATAL_ERROR "pureboot_add_loader(${name}): HALF_DUPLEX puts both "
"directions on RX (${PB_RX}); TX ${PB_TX} contradicts it")
endif()
set(PB_TX ${PB_RX})
endif()
if(NOT PB_TX)
set(PB_TX pb1)
endif()
foreach(_pin ${PB_RX} ${PB_TX})
if(NOT _pin MATCHES "^p[a-h][0-7]$")
message(FATAL_ERROR "pureboot_add_loader(${name}): pin '${_pin}' is not of the form pb1")
endif()
endforeach()
if(PB_SERIAL STREQUAL "autobaud")
set(_serial_defines PUREBOOT_AUTOBAUD PUREBOOT_RX=${PB_RX} PUREBOOT_TX=${PB_TX})
else()
set(_serial_defines PUREBOOT_SOFT_SERIAL PUREBOOT_RX=${PB_RX} PUREBOOT_TX=${PB_TX})
endif()
# sw:<RX>,<TX> as port letter and bit, upcased — with @<n> where
# the TX pin is a USART's own TXD, since a harness driving that
# link has to know the USART owns the pin until the loader
# releases it.
string(SUBSTRING ${PB_RX} 1 2 _rx_pin)
string(SUBSTRING ${PB_TX} 1 2 _tx_pin)
string(TOUPPER "sw:${_rx_pin},${_tx_pin}" _link)
string(REPLACE "SW" "sw" _link ${_link})
get_property(_tx0 GLOBAL PROPERTY PUREBOOT_USART0_TX)
get_property(_tx1 GLOBAL PROPERTY PUREBOOT_USART1_TX)
get_property(_rx0 GLOBAL PROPERTY PUREBOOT_USART0_RX)
get_property(_rx1 GLOBAL PROPERTY PUREBOOT_USART1_RX)
if(_usart AND PB_TX STREQUAL _tx0)
set(_link "${_link}@0")
elseif(_usart1 AND PB_TX STREQUAL _tx1)
set(_link "${_link}@1")
elseif(PB_TX STREQUAL PB_RX AND _usart AND PB_RX STREQUAL _rx0)
# One-wire on a USART's RXD: RXEN forces that pin's direction
# (§20.7.3), so the driven shared pin is held exactly like a
# TXD — the harness models the hold either way.
set(_link "${_link}@0")
elseif(PB_TX STREQUAL PB_RX AND _usart1 AND PB_RX STREQUAL _rx1)
set(_link "${_link}@1")
endif()
endif()
endif()
if(NOT PB_BAUD)
if(PB_SERIAL STREQUAL "software")
pureboot_default_baud(${PB_CLOCK} 1 PB_BAUD)
else()
pureboot_default_baud(${PB_CLOCK} 0 PB_BAUD)
endif()
endif()
if(PB_SERIAL STREQUAL "autobaud")
# No clock and no baud reach the image; the window is a poll budget.
set(_defines ${_serial_defines})
else()
set(_defines PUREBOOT_CLOCK_HZ=${PB_CLOCK} PUREBOOT_BAUD=${PB_BAUD} PUREBOOT_TIMEOUT=${PB_TIMEOUT}
${_serial_defines})
endif()
if(DEFINED PB_OSCCAL)
math(EXPR _osccal "${PB_OSCCAL}" OUTPUT_FORMAT DECIMAL)
if(_osccal LESS 0 OR _osccal GREATER 255)
message(FATAL_ERROR "pureboot_add_loader(${name}): OSCCAL ${PB_OSCCAL} is not one byte")
endif()
list(APPEND _defines PUREBOOT_OSCCAL=${_osccal})
endif()
add_executable(${name} ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/pureboot.cpp)
target_link_libraries(${name} PRIVATE libavr)
target_compile_definitions(${name} PRIVATE ${_defines})
# Codegen shaping for the loader TU only. At -Os GCC otherwise rewrites the
# byte-stream loops' counters into end-pointer forms that cost registers
# (-fno-ivopts, -fno-split-wide-types), leaves register pressure on the
# table with the default allocator (-fira-algorithm=priority), and keeps
# expression temporaries in registers (-fno-tree-ter) — but every loop body
# here contains a call, so a register held across it costs more than the
# load-immediate it saves. The set is fitted to the loader's body and has to
# be re-measured when that body changes: -fno-move-loop-invariants belonged
# here while the command loop carried four transfer bodies and costs bytes
# now that it carries one, and -fno-ivopts is fitted per backend — an
# autobaud body needs ivopts to keep the calibration countdown a single
# induction variable (without it the counter is duplicated and the
# measurement loop runs 9 cycles instead of its contracted 7), while the
# fixed-baud bodies still measure smaller with it off.
if(PB_SERIAL STREQUAL "autobaud")
target_compile_options(${name} PRIVATE
-fira-algorithm=priority -fno-tree-ter -fno-split-wide-types)
else()
target_compile_options(${name} PRIVATE
-fno-ivopts -fira-algorithm=priority -fno-tree-ter -fno-split-wide-types)
endif()
target_link_options(${name} PRIVATE -nostartfiles -Wl,--section-start=.text=${_base_hex}
-Wl,--defsym=pureboot_app=${_app} ${_wrap})
add_custom_command(TARGET ${name} POST_BUILD COMMAND ${CMAKE_SIZE} $<TARGET_FILE:${name}>)
# The ELF is a container, never flashed: .hex for a programmer, .bin (the
# slot's bare bytes) for --update-loader.
add_custom_command(TARGET ${name} POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O ihex -R .eeprom
$<TARGET_FILE:${name}> $<TARGET_FILE:${name}>.hex
COMMAND ${CMAKE_OBJCOPY} -O binary -R .eeprom
$<TARGET_FILE:${name}> $<TARGET_FILE:${name}>.bin)
set_target_properties(${name} PROPERTIES PUREBOOT_HZ ${PB_CLOCK} PUREBOOT_BAUD ${PB_BAUD}
PUREBOOT_LINK ${_link})
endfunction()

704
pureboot/README.md Normal file
View File

@@ -0,0 +1,704 @@
# pureboot
A serial bootloader on [libavr](https://git.blackmark.me/avr/libavr), pure by
constraint: one C++ source, no inline assembly, no global register variables
(attributes and compiler flags allowed), **a 512-byte slot on every chip
libavr targets — all 37**. The device speaks primitives; every composite — verify,
erase, reset-vector surgery, updating the loader itself — lives in the host
tool (`pureboot.py`).
The image is **position-independent**: control flow is PC-relative, the
transfer paths take wire addresses, the write guard protects the slot the code
is *running* in (from the runtime return address), nothing else is
flash-resident to address at all, and the application jump is an indirect call
to an absolute entry. The identical binary therefore runs from any slot with
every command intact, which makes pureboot **its own staging loader**: the host
installs the same binary one slot below the resident, jumps into it, and lets
it rewrite the resident. The lint holds it to that literally — the image must
come out byte-identical linked at a different base.
## Chips
The Stock column is the default configuration: the hardware USART0 at 115200
8N1 on a 16 MHz crystal, or the software UART on RX = PB0 / TX = PB1 at
57600 8N1 on the tinies' RC oscillator (9.6 MHz on the t13s, 8 MHz above).
Every axis moves per build — see *Configuration*. The Autobaud column is the
worst configuration the space produces for the chip: the clock-free build —
it alone carries the calibration machinery — with the `OSCCAL` trim baked
and, where the chip has a USART, the link deployed on that USART's own pins,
which the loader then has to release (*Pin ownership*). Folding the same
build onto a single pin (*One-wire*) measures identically on every chip, so
the column covers that twin too. On default pins without the trim the same
loaders run 4–10 B smaller.
| Chip | Flash | Loader at | Link | Stock | Autobaud |
|---|---|---|---|---|---|
| ATtiny13, ATtiny13A † | 1 KiB | 0x0200 | software | 384 B | 474 B |
| ATtiny25 † | 2 KiB | 0x0600 | software | 388 B | 466 B |
| ATtiny45 † | 4 KiB | 0x0e00 | software | 388 B | 466 B |
| ATtiny85 † | 8 KiB | 0x1e00 | software | 388 B | 466 B |
| ATmega8, 8A | 8 KiB | 0x1e00 | USART0 | 362 B | 494 B |
| ATmega16, 16A | 16 KiB | 0x3e00 | USART0 | 364 B | 496 B |
| ATmega32, 32A | 32 KiB | 0x7e00 | USART0 | 364 B | 496 B |
| ATmega48, 48A, 48P, 48PA † | 4 KiB | 0x0e00 | USART0 | 378 B | 468 B |
| ATmega88, 88A, 88P, 88PA | 8 KiB | 0x1e00 | USART0 | 388 B | 478 B |
| ATmega168, 168A, 168P, 168PA | 16 KiB | 0x3e00 | USART0 | 390 B | 480 B |
| ATmega328, 328P | 32 KiB | 0x7e00 | USART0 | 390 B | 480 B |
| ATmega164A, 164P, 164PA | 16 KiB | 0x3e00 | USART0 | 390 B | 480 B |
| ATmega324A, 324P, 324PA | 32 KiB | 0x7e00 | USART0 | 390 B | 480 B |
| ATmega644, 644A, 644P, 644PA | 64 KiB | 0xfe00 | USART0 | 384 B | 474 B |
| ATmega1284, 1284P | 128 KiB | 0x1fe00 | USART0 | 410 B | 502 B |
† No hardware boot section: the host patches the reset vector, and the budget
is 510 bytes, since the slot's last word is the trampoline.
The tightest fit in the whole space is therefore the 1284s' 502 of their
512: they alone carry the far-flash machinery (ELPM reads, RAMPZ page
commands) on top of everything the column already stacks. The flash bank
riding in a transfer's selector byte keeps even those chips' addressing the
same 16-bit form every other chip uses, which is why they are no longer the
outlier they were.
The software UART enables the RX pull-up; TX idles high. All multi-byte wire
quantities are little-endian.
## Configuration
Every deployment axis is a build parameter of `pureboot_add_loader()` (in
`pureboot/CMakeLists.txt`) — the one way a loader target is created, by this
repo's build and by a downstream project alike:
| Argument | Meaning | Default |
|---|---|---|
| `CLOCK <hz>` | the clock the board runs | 16 MHz megas, 8 MHz t25/45/85, 9.6 MHz t13s |
| `BAUD <bd>` | the wire rate | the ladder below |
| `SERIAL auto\|hardware\|software\|autobaud` | the link backend | `auto`: the hardware USART where the chip has one |
| `USART <n>` | the USART instance (x4 megas carry two) | 0 |
| `RX <pin>`, `TX <pin>` | software-UART pins | `pb0`, `pb1` |
| `TIMEOUT <s>` | the activation window | 8 |
| `OSCCAL <byte>` | a measured oscillator trim, applied before anything runs | none — no value, no code |
| `HALF_DUPLEX` | one-wire: both directions on one line (*One-wire* below) | off |
The default baud is the fastest of 115200/57600/38400/19200/9600 the clock
reaches within 2.5 % — the same U2X-included divisor search libavr's baud
solver runs — and on a software build additionally within the polled
receiver's 100-cycles-a-bit floor. Whatever is picked or overridden is
re-checked in the compile: an infeasible combination, or a USART the chip does
not have, fails with a named static assert.
Putting a bit-banged link on a USART's own pins is a supported deployment, and
the usual one where a board's USB bridge is wired to RXD/TXD: the link's `init`
clears that USART's `UCSRnB` first, because while its `TXEN` is set the USART —
not the port register — owns the TX pin, and a loader entered from an
application that left it enabled would receive and obey while answering nothing
(§20.6.3). It costs one store — four bytes on the extended-I/O chips, two on
the classic megas — and only on those pins.
`SERIAL autobaud` takes neither: the loader **measures** the host's bit timing
at run time, so `CLOCK` and `BAUD` are not build parameters there and one
binary per chip serves every clock and every rate. It is for the deployments
whose clock is not known at build time and does not hold still — the internal
RC oscillator, ±10 % from the factory and moving with supply and temperature —
where a fixed-baud software build has to be rebuilt per clock and still drifts
out of tolerance. The cost is that it is software-serial only (a hardware USART
needs its divisor programmed) and that activation counts poll iterations rather
than seconds, since there is no clock to convert them against
(`PUREBOOT_AUTOBAUD_POLLS`, default 4,000,000). The wait spends nine cycles a
poll (measured, and held by the `pureboot.window.autobaud` gate), so the
default window is 36 M cycles: 4.5 s at 8 MHz, 3.75 s at 9.6 MHz, 36 s at
1 MHz.
**Pick the rate by cycles a bit, and leave the oscillator room.** What the
calibration can measure is bounded by how many clock cycles one bit lasts, so a
rate is only ever sensible relative to the clock. Two different floors matter:
| | cycles a bit |
|---|---|
| the logic's floor — exact clock, simulated | solid to ~36, fails outright by ~31 (`pureboot.autobaud` gates a point here) |
| a factory-trimmed internal RC, measured on an ATtiny13A | reliable at ~118; already locking 1 attempt in 5 by ~59 |
The gap is the oscillator's own jitter, and no exact-clock simulation shows it.
So on an RC part, **budget about 100 cycles a bit** — the same order as the
fixed-baud software receiver's floor — rather than the logic's ~36. Measured
envelope on that ATtiny13A, with an application resident: 9.6 and 4.8 MHz reach
115200, 1.2 MHz reaches 9600, 600 kHz reaches 4800, 128 kHz reaches 2400.
One trap in testing this: on a patched-vector chip an **erased** application
region walks straight back up into the loader, so every expired window opens
another one and the host's retries eventually catch the pulse. That reads as far
more reliable than the same part with an application resident, which gets one
window per reset. Measure with an application in place.
## One-wire
`HALF_DUPLEX` puts both directions on one line — the deployment for a board
with a single spare pin, or a native-UART bootloader's shared-line wiring.
Each backend has its shape:
- **Software and autobaud links** fold onto the RX pin (`RX == TX` spells
the same deployment directly). The pin idles as the receiver's pull-up
input; each transmitted frame takes the pin's direction and hands it back
with the stop bit's level already on the pull-up, so neither flip makes
an edge. This costs nothing: the frame's direction wrap is exactly what
the dropped second-pin init paid, and the tightest image in the space —
the 1284s' autobaud + `OSCCAL` on their USART's RXD — measures the same
502 bytes one-wire as two-wire. On a USART's own pin the release applies
as ever, RXD included: `RXEN` forces that pin's direction (§20.7.3),
which a receive-only link could live with and a driven shared pin cannot.
- **The hardware USART** (`SERIAL hardware`/`auto` + `HALF_DUPLEX`) uses
libavr's `.half_duplex` turn-around — exactly one direction enabled at a
time, each written byte held to transmit-complete before the line can be
released — and needs RXD and TXD tied together off-chip. It costs
+42…50 B over the stock loader (m8 404, m328P 440, 1284P 460 — all far
inside the slot); the activation window is unchanged, its poll merely
runs through the release-line test (18 cycles a poll in bit-addressable
I/O, 22 in extended — measured, and held per chip by
`pureboot.window.halfduplex`).
Host wiring, for an FTDI-style adapter: **adapter TX through ~1 kΩ to the
line, adapter RX and the MCU pin directly on it.** The resistor lets the MCU
win the line while it answers; the price is that the adapter reads back every
byte it transmits. `pureboot.py --one-wire` consumes that echo byte for byte
— a missing echo is reported as the wiring fault it is, and a device reply
that lands between the echoes of the knock (a loader already in session
re-prompts mid-knock) is held for the reader. The knock is the protocol's
one blind multi-byte write, so on real wiring its second byte can be lost to
that collision outright; the tool's knock retries absorb it. Everything else
is ack-paced and cannot collide.
A downstream project brings its usual libavr setup (the `libavr` target, the
chip via the `LIBAVR_MCU` toolchain preset), consumes this directory, and
states its deployment — an ATmega328P on its shipped 1 MHz fuses with the
software UART on hand-picked pins, say. A submodule pins the loader version
(the tags name them; this repo pins its own libavr the same way), where
FetchContent tracks whatever `main` is:
```cmake
# git submodule add <forge>/avr/bootloader.git bootloader — or FetchContent
add_subdirectory(bootloader/pureboot pureboot)
pureboot_add_loader(myboot CLOCK 1000000 SERIAL software TX pb1 RX pb5)
```
The function emits the ELF plus `myboot.hex` (the programmer artifact) and
`myboot.bin` (the self-update image), prints the size, and stamps the resolved
deployment on the target as the `PUREBOOT_HZ`, `PUREBOOT_BAUD` and
`PUREBOOT_LINK` properties — what a flashing script or test harness needs to
speak to the build. This exact deployment runs the full protocol suite in CI
(`pureboot.custom`).
## Activation
Reset enters the loader (BOOTRST on the boot-sectioned megas, the patched
reset vector elsewhere) — except a watchdog reset, which hands straight to the
application with no activation window, since the application owns its watchdog.
This is deliberate: it lets an application reboot itself instantly rather than
sit through the window. The application must clear WDRF itself (libavr's
`watchdog::disable()` does). **Gotcha:** WDRF is sticky (cleared only by
software, not by a later reset), so an application that watchdog-resets and
never clears it diverts *every* subsequent reset — external ones included —
past the window too, and the loader becomes reachable only through an external
programmer until the flag is cleared. A serial recovery path therefore assumes
the application clears WDRF on its own reset path.
The host then knocks `p` then `b`, each awaited byte under a fresh activation
window; any other byte is discarded and awaited again, so line noise can delay
the loader but never lock it. A window expiring on an idle line boots the
application.
An autobaud build opens differently, because it has to learn the rate before it
can read a byte at all: the host sends the **calibration byte 0xC0** — a start
bit plus six zero data bits form one low pulse of seven bit-times — and the
loader times that pulse into its bit period. A single `p` then activates; the
pulse has already proven a host is present, which the two-byte knock exists to
establish elsewhere. Both waits are bounded, so a stray low pulse with no host
behind it costs one window and then boots the application rather than holding
the loader.
The window is a compile-time constant (`TIMEOUT`, 8 s by default), so the whole
EEPROM belongs to the application — pureboot keeps no state of its own.
Re-timing a deployed loader is a self-update with a re-timed build. An autobaud
build counts poll iterations instead (`PUREBOOT_AUTOBAUD_POLLS`), there being
no clock to turn into seconds.
## Session
After the knock the loader stays in its command loop until `J` jumps away or
the chip resets. Before reading each command it waits for any pending EEPROM
write and sends the prompt `+` (0x2b), which is therefore also the previous
command's completion ack. A session is: await `+`, send a command, read its
reply, repeat.
Addresses are **byte addresses within a 64 KiB bank**, and the bank rides in
the command's selector byte, so no command has to speak word addresses. `J` is
the exception: its address is a word address, because that is what the
hardware's own jump takes — it still carries a selector byte (reserved,
ignored) so its decode is the same three reads as every other command's.
EEPROM and data-space addresses and all counts are bytes.
The loader trusts the host to keep addresses in range: it does not bound them
against the chip. **Gotcha:** a write (or read) that runs past `E2END` wraps —
EEAR is only as wide as the array, so an address past the end truncates onto
low EEPROM and the write silently overwrites it. Keeping transfers within the
real sizes is the host's job (the shipped tool does); the flash budget is
better spent on features than on re-checking a bound the host already holds.
| Cmd | Arguments | Reply |
|---|---|---|
| `b` | — | 4 bytes: the pureboot version, then the three signature bytes |
| `G` | sel8, addr16, n8 | n bytes from the selected space (n = 0 means 256) |
| `g` | sel8, addr16, n8, then n data bytes | `+` per byte, sent once its write has begun |
| `W` | sel8, addr16, then one page of data | — (completion = next prompt) |
| `J` | sel8 (reserved), word address (16-bit) | `+`, then execution continues there |
| other | — | ignored; the loop re-prompts (send a junk byte, await `+`, to resync) |
`G` and `g` are one letter in two cases, which is the whole command set for
every memory: the **selector** byte's low nibble names the space and its high
nibble carries the flash bank.
| Space | | |
|---|---|---|
| 0 | flash | read-only here; it is written through `W` and the SPM space |
| 1 | EEPROM | |
| 2 | data | SRAM — and with it the register file and every I/O register, which share the data address space on AVR |
| 3 | fuse and lock | index 0..3 in the hardware's own Z order: low, lock, extended, high |
| 4 | SPM | write-only: the byte goes to SPMCSR and fires the instruction at the address |
The data space is worth more than it looks. pureboot keeps **zero static RAM**
and pushes no register, so at loader entry an application's SRAM is still
whatever the application left there, bar the handful of bytes of return-address
stack — which makes `G` over space 2 a post-mortem of a running application,
not just a poke hole. The same address space carries the register file and the
I/O registers, so peripheral state is readable too; reading some of those has
side effects (reading UDR clears its flags), which is the host's business to
know.
Programming a page is therefore `W` to fill the buffer, then a `g` to the SPM
space for the erase, another for the write, and on a boot-sectioned chip a
third to re-enable the RWW section — `0x03`, `0x05` and `0x11`, the SPMCSR
encodings every part pureboot targets shares. The loader carries no page-commit
logic of its own, and the same primitive reaches every other SPM operation,
lock bits included.
The SPM store and the SPM instruction must issue within four cycles of each
other (§26.2), which no host can hit across a serial link — so this one
primitive is *fused* rather than being a poke of SPMCSR followed by a poke of
something else. That four-cycle window is the floor on how low-level a
bootloader's primitives can go; it is not a byte-count decision.
An SPM command aimed at the 512-byte slot the loader is **running in** is
dropped, so a broken host cannot brick the running copy, while a staged copy
one slot lower may rewrite the resident — which is what a self-update is.
The loader never clears the SPM buffer before a fill, so **one `W` may program
the wrong bytes, and the host is what fixes it**. The buffer is write-once per
word until cleared, and two things leave words in it: a refused page, and —
where SPM runs from anywhere, the tinies and the m48s — an application that
self-programmed before entering. The next page write takes those stale words
and clears them, since a page write auto-erases the buffer (§26.2.1; §19.2 on
the tinies), so repeating it programs correctly. The host therefore verifies
every page it writes and rewrites what comes back wrong (three retries, then it
stops).
`g` is host-paced: send the next byte only after the previous byte's `+`. Fuse
*writing* does not exist — SPM reaches flash and boot lock bits only.
`J` is the one control-transfer primitive: it runs the application (word 0 or
the trampoline word, both derived from the chip) and moves between loader
copies during a self-update. A jump to a slot's base re-enters that copy's own
startup, which must then be knocked afresh.
`b` answers with the loader's identity — its version and the chip's signature —
and nothing else. Everything else the host needs (page size, loader base,
EEPROM size, whether the reset vector must be patched, how many flash banks)
follows from the signature, and the host holds that table; the loader derived
the same facts from its own chip database at build time, so nothing is guessed,
it is simply not sent twice.
An update image, though, is a bare 512-byte slot with no device to ask, and
installing one built for another chip bricks the target. Every loader image
therefore carries a six-byte **stamp** — `'P'`, `'B'`, the version, the three
signature bytes — which the loader itself never reads and the host tool refuses
to install a mismatch against.
## Version
`b`'s first byte is the **pureboot version** — the loader's one identity
number, and the only way to tell what a deployed loader is. Nothing else is
numbered: the wire protocol has no version, a pureboot version implies it, and
the host tool holds that map. The tool states the window of loader versions it
speaks (`OLDEST_LOADER`/`NEWEST_LOADER` in `pureboot.py`), and a version that
changes the protocol becomes the new floor there. A loader newer than the tool
is refused by name rather than decoded on the assumption that nothing moved.
Two generations exist. **1 through 4** speak one session — a 12-byte info block
from `b`, and a command per memory (`R`/`W` flash, `r`/`w` EEPROM, `F` fuses).
**5** replaced those with the single `G`/`g` pair over selector-named spaces
above; the shipped tool speaks both, choosing on the version it reads, so a
deployed pureboot 4 stays drivable and self-updatable to 5. **6** changes
nothing on the wire: it marks the builds that may carry a baked `OSCCAL` trim
(Configuration), so a tool driving an update knows such images exist. **7**
moves `J` onto the unified decode — it gains the selector byte the table
shows, which older loaders do not read, so the tool sends each form to the
version that speaks it — and re-homes the autobaud unit into the GPIOR pair
on the chips that have one (Session: what must not be written), which is
where `--info`'s measured clock now reads it on those parts. **8** changes
nothing on the wire either: it marks the builds whose deployment may be
one-wire (*One-wire* above) — the hardware USART's half-duplex turn-around,
or a software link folded onto a single pin. The host-side trace is
`--one-wire`, the echo discard a shared line requires of any tool driving
it.
Every closed generation is tagged in this repo at its era's last commit — the
commit just before the next version bump, so a tag holds everything its
version ever gained — and each tag carries the `libavr/` submodule pinned to
the libavr that loader was built against, as the whole libavr era does commit
by commit. `git checkout v3 && git submodule update --init libavr` followed by
the usual preset build therefore reproduces the v3 loader exactly; the open
generation is `main`.
Collapsing four command bodies into one transfer loop is what paid for the
version: the data space, the host-issued SPM operations and the fuses now share
the loop, the cursor and the argument decode that `R`/`r`/`w` each carried a
copy of. The loader shrank while gaining all three.
The tool carries its own version, free to drift; `--version` prints it and the
window.
## Deployment
The build leaves three artifacts per chip. The ELF is a container for the
tests and objcopy, never flashed. The **.hex is the programmer artifact**: it
carries its own addresses and lands the loader in its top slot, touching
nothing else. The **.bin is the self-update image** — the slot's bare bytes.
**Boot-sectioned megas**: program the loader at `flash − 512` with an external
programmer. Every such mega has a BOOTSZ step whose boot section is exactly
the 512-byte slot — the second-smallest step on the 8 KiB and 16 KiB chips,
the smallest on the 32 KiB ones — so the ATmega328P profiles below apply to
every one of them with its own addresses; the per-chip BOOTSZ ladders live in
the host tool (`BOOT_FUSE`).
The **644s and 1284s** are the geometry's sweet spot: their smallest boot
section (512 words = 1 KiB) is exactly *two* slots, so the resident and its
staging slot both live inside the minimum section. Self-update needs no fuse
step up, and the standalone profile does not exist — reset lands one erased
slot below the loader (0xfc00 / 0x1fc00) and walks up into it.
ATmega328P profiles (addresses for its 32 KiB):
| BOOTSZ | BOOTRST | Behavior |
|---|---|---|
| 256 words (512 B) | programmed | *Standalone*: reset always enters the loader; **self-update impossible** (the staging slot lies outside the boot section, where SPM is disabled). |
| 512 words (1 KB) | unprogrammed | *Self-update, app-first*: reset always boots the application, which owns all 31.5 KB and must offer its own jump to 0x7e00 to reach the loader (a virgin chip reaches it by reset across erased flash). Updates are power-fail-safe except mid-rewrite of the resident slot itself (no reset path leads to the staging copy then). |
| 512 words (1 KB) | programmed | *Self-update, loader-first*: reset lands at 0x7c00 — the staging slot, normally erased, so execution walks up into the loader; during an update it is the staging copy itself, so a mid-rewrite power loss recovers by reset. The loss windows move to the staging install/retire page writes instead (page-write scale). The host keeps `[0x7c00, 0x7e00)` clear of application data (`--force` overrides). |
Applications are flashed unmodified here — word 0 stays the application's own
reset vector, and the hand-over jumps to 0.
**Patched-vector chips — the tinies and the m48s** (no boot section; the m48s'
SPM runs from the entire flash, Atmel-8271 §26): program the loader at
`flash − 512`; erased flash below it walks up into the loader, so a virgin
chip activates. Flashing an application then takes reset-vector surgery: word
0 becomes an `rjmp` to the loader base, and the application's own entry is
re-encoded as a trampoline `rjmp` in the word just below the loader
(`base − 2`, where the hand-over jumps). Every other vector stays the
application's. The patched page 0 and the trampoline page are written *first*
and an erase runs top-down, so from the first write on an interruption still
resets into the loader.
A .bin programmed at address 0 by mistake is dead weight on a boot-sectioned
mega (SPM only executes from the boot section — reflash the .hex), but *runs*
on a patched-vector chip, and the ordinary `--update-loader` flow re-homes it
into the top slot from there (`pureboot.rehome`).
**Fixed-baud on an internal RC oscillator is a deployment risk the build
cannot see.** The factory trim is ±10 % where an 8N1 frame survives about
±4: a part at the edge answers nothing at the built rate, and the symptom —
silence — reads as a wiring fault (a real ATtiny13A measured −5.5 %, outside
every standard rate at its own documented default). The **autobaud build is
the deployment-proof backend**: it has no rate to miss. Where fixed-baud on
RC is wanted anyway, measure first and bake the trim: an autobaud session's
`--info` prints the part's true clock from the loader's own measured bit
period, OSCCAL moves the oscillator about 1 % per step, and `OSCCAL <byte>`
builds the correction in — one build–measure iteration converges. A loader
already deployed and silent is diagnosed with `--scan` (Host tool).
## Updating the loader
`pureboot.py --update-loader new_pureboot.bin` replaces the resident loader
with any pureboot build — a re-timed window, a newer version — using the
loader itself as its own staging loader. The image is the loader's own 512
bytes as a raw binary, or the Intel HEX the build emits beside it.
One thing the image cannot tell the host: **which link it speaks.** The update
works by entering copies of the *new* image (steps 3 and 4 below), so a build
made for another baud or another backend answers on that one and not on the
session's — and 512 bytes of position-independent code carry no header to read
it from. Where the new image's link differs, name it:
```sh
# a 57600 fixed-baud resident, replaced by an autobaud build
pureboot.py --port … --baud 57600 --update-loader ab.bin --staged-autobaud
# …or by a 38400 build of the same backend
pureboot.py --port … --baud 57600 --update-loader sw38400.bin --staged-baud 38400
```
The host retunes on the open port, so no DTR pulse resets the copy it is talking
to. Omit them against a changed link and the update stops after installing the
staging copy, saying so and naming this as the cause.
An `OSCCAL`-baked image is a link change in effect even at an unchanged rate
on paper: the staging copy shifts the physical clock the moment its `run()`
starts, and from then on speaks exactly what it was built for. Declare it
like any other link change — `--staged-baud` with the new build's rate.
The preflight refuses an image built for another chip: the stamp every pureboot
binary carries must resolve to the device's own geometry, and the error names
both. Die revisions share their base signature and geometry, so their images
are interchangeable — as the silicon is.
1. The staging slot `[base−512, base)` is saved to a host-side state file (on
the 1 KB tiny13s that is the whole application, vectors included).
2. The resident installs the update image there. On the patched-vector chips
the host composes the slot's last word as a jump to the resident base, so
even an abandoned staging copy times out into a loader. A loader already
sitting whole in the staging slot is left as the staging copy instead —
rewriting it would only meet its own running-slot guard.
3. `J` enters the staging copy, which rewrites the resident slot. Where a
patched reset vector routes through the resident, the host first re-aims
word 0 at the staging copy, so a power loss mid-rewrite still resets into a
loader; on the tiny13s the staging slot carries the reset vector itself.
4. `J` enters the new resident, which restores the staging slot's saved
content, and the state file is discarded.
Every phase is idempotent and keyed off the actual flash state, so re-running
the same command after any interruption resumes and completes — with one
qualification, which is the link again: from step 2 on, the copy the re-run has
to reach is the *new* image, so a resumed run needs the same `--staged-*` as the
first one. On a patched-vector part step 3 also re-aims word 0 at the staging
copy, so after that point a reset reaches the new image's link and **only** that
one; a re-run on the resident's link finds nothing at all. The state file carries
the only bytes not recoverable from the device; losing it mid-update still
completes the update, and the staging region comes back by reflashing the
application. A boot-sectioned mega needs its fuses for the preflight — read
from the device, or supplied with `--assume-fuses` where reading is impossible
(simulators).
## Host tool
`pureboot.py` — Python 3, standard library only. The port layer is the one
platform-specific part: termios drives any tty on POSIX (a USB adapter as well
as a simavr pty), the Win32 serial API through `ctypes` drives a COM port on
Windows (`--port COM6`; the `\\.\` form for two-digit ports is supplied by the
tool). Opening the port asserts DTR and RTS on both, so a board that wires DTR
to reset gets its reset pulse and opens the activation window by itself.
pureboot.py --port /dev/ttyUSB0 --baud 57600 \
--info --fuses --flash app.hex
Operations run in a fixed order within one session: info, fuses, loader
update, flash (erase / program / read / verify), EEPROM (the same), then
`--peek`/`--poke` — then the loader hands over to the application. `--stay` keeps the session alive
instead, and a later invocation reconnects into it. `--flash` and `--eeprom`
verify by read-back unless `--no-verify`, and a flash page that reads back
wrong is rewritten up to three times before the run stops (see `W` above).
`--verify-flash` only reports. Images are raw binary, or Intel HEX by
extension. `--force` overrides the refusable safety checks — today, flashing
application data into a mega's reset walk region.
`--autobaud` opens with the calibration pulse instead of the plain knock, for a
loader built `SERIAL autobaud`; the rest of the session is identical, at
whatever `--baud` the host chose. Its `--info` adds the **measured clock** —
the loader's bit-period unit, decoded and multiplied by the session rate —
which is the number an `OSCCAL` bake or a fixed-baud build for the part is
held against; `--clock <hz>` states the drift against a nominal.
`--one-wire` marks the link as a shared line (*One-wire* above): the tool
reads back and verifies its own echoed bytes, whatever the backend.
It combines with everything, `--scan` included — undiscarded echoes would
answer every rate a scan probes.
`--scan` is the diagnosis once a fixed-baud loader has gone silent: it walks
±10 % around `--baud` in 2 % steps, nearest first, one probe per activation
window — reset the target as each probe announces itself (a board with DTR
wired to reset is pulsed by the probe's own port-open). A loader
off-frequency answers at its oscillator's ratio, and the report gives the
found rate as the session workaround, the offset, the OSCCAL correction's
direction at ~1 % per step, and the autobaud way out. Standalone — no other
operation combines with it.
`--peek ADDR[:N]` and `--poke ADDR:HEX` reach the data space (pureboot 5) —
SRAM, and through the same address space the register file and every I/O
register. Reading an I/O register can have side effects (reading UDR clears its
flags), which is the caller's business to know.
Reads are safe anywhere; **two small regions cannot be written without ending the
session,** because they are what the loader is standing on:
- the **top of SRAM**, where its stack lives — a handful of bytes below RAMEND;
- on an **autobaud** build, the **measured bit period**: two bytes in
GPIOR2:GPIOR1 where the chip has the pair (data `0x32..0x33` on the
t25/45/85, `0x4A..0x4B` from the x8 generation on — such a loader has *no*
static RAM at all), and the two bytes at RAMSTART on the chips without one
(the t13s and classic megas), where they are the whole of the loader's
static RAM. Overwrite either home and the next reply is timed against
garbage — the symptom is a mangled prompt byte rather than any error; the
loader is fine, it simply is no longer speaking the agreed rate.
Both are self-inflicted rather than defects, and a reset clears them. Note also
that `--poke` can write OSCCAL, which does take effect — but a session can only
survive a step or two of it before the clock walks the link out of the rate
autobaud locked to, and OSCCAL reverts on reset regardless.
Readouts come one fact per line: `--info` prints the device's version and
signature and the geometry that follows from them, `--fuses` each fuse byte
plus, on a boot-sectioned mega, its decoded meaning. Transfers that take wire time draw a transient progress bar on stderr
when it is a tty. `-v`/`--verbose` adds the decisions as they happen: knock
counts, the programming plan, update state handling and per-phase page counts.
## Tests
libavr rides as the `libavr/` submodule (`git submodule update --init libavr`);
`LIBAVR_ROOT` (cache or environment) overrides it for tandem development
against a working tree. `tools/check.sh` runs every chip's workflow (`--full`
adds the reflect-mode builds of libavr's spot set; `tools/make_presets.py`
regenerates the presets).
Per chip preset, `ctest` runs:
- `pureboot.size` — the 510-byte (patched-vector) / 512-byte budget;
- `pureboot_*.size` — the size matrix: the serial backends × the clock ladder
(1/8/16 MHz; the t13s' own RC menu), the USART1 instance across that same
ladder on the x4 chips, and `pureboot_sw_wide`, the slowest ladder rate at
the fastest clock — where a software UART's per-bit spin outgrows its
one-register delay loop and takes the 16-bit one. That is the largest image
the configuration space produces, and a shape the ladder default (always the
*fastest* rate a clock reaches) never picks. Pins are an axis for one reason
only, and it is enough: a bit-banged link on a USART's own pins has to
release that USART, so `pureboot_{sw,autobaud}_on_usart{0,1}` build there
too. The timeout is a constant and is no axis;
- `pureboot_autobaud.size` — the clock-free build, which has no clock or baud
axis of its own: one binary per chip has to serve every point the matrix
below sweeps. `pureboot*osccal*.size` add the `OSCCAL` trim on the stock
shape and on the tightest image in the space (autobaud on a USART's own
pins), holding both of the trim write's addressing encodings to the budget;
- `pureboot_autobaud.unit` — the measured bit period sits where `--info`
reads it (wire contract, not layout accident): in the GPIOR pair, with no
RAM object at all, on the chips that have one; as the loader's only RAM
object at exactly ram_start elsewhere;
- `pbm_*.size` — with `PUREBOOT_FULL_MATRIX=1`, the exhaustive cross product
replacing that compact matrix, on **every** chip: every plausible oscillator
(the internal ones, the CKDIV8 floor, the plain and the UART crystals) ×
every rate reachable from it × every backend, unreachable combinations
dropping out rather than aborting the configure. Thousands of points per
chip, and cheap enough to run rather than reason about;
- `pureboot.pi` — the position-independence lint: no absolute `jmp`/`call`, no
flash-resident section but `.text`, and the image byte-identical when linked
at a different base — which is position independence itself rather than a
proxy for it;
- `pureboot.handshake` — the host tool's activation must not hang on a target
that never falls quiet: the drain after a prompt is bounded by the handshake
deadline, and a well-behaved loader still connects;
- `pureboot.updatelink` — an update whose image changes the baud or the backend
must follow the staging copy onto *its* link, since that copy is the new image;
and where nothing was declared, the failure must name the link rather than
report a bare activation timeout, because by then the staging slot is written
and on a 1 KiB tiny that was the application;
- `pureboot.planner` — the host tool's pure logic: programming orders and their
recovery properties, the surgery, the staging composition, the boot-fuse
decode, the update preflight over synthetic fuse bytes, and the repairing
verify against a fake device;
- `pureboot.scan` — `--scan`'s walk and report logic: the probe order, the
rate arithmetic, and the trim advice's direction. A pty carries bytes at
any termios rate, so the rate physics itself belongs to the hardware
harness, and what the wire would arbitrate is pinned as logic;
- `presets.generated` — CMakePresets.json matches its generator
(`tools/make_presets.py --check`), so a hand edit or a generator change
cannot drift the pair apart;
- `pureboot.protocol` — end to end against a simavr device
(`test/pureboot_device.cpp`: a hardware USART as a pty, or a cycle-timed
GPIO⇄pty bridge for a software-UART build, plus the SPM/NVM module simavr's
tiny cores lack) driven by the real host tool through knock-from-reset,
program + verify of both memories, session reconnect, an external reset
through the patched vector, and the hand-over to a fixture application whose
banner proves the launch — cross-checked against the simulator's
ground-truth memory dumps and an independent decode of the surgery;
- `pureboot.reloc` — the identical image one slot below the resident serves the
complete command set from there;
- `pureboot.rehome` (t85) — a loader programmed at address 0 or in the staging
slot re-homes into the top slot through the ordinary update flow;
- `pureboot.custom` (328P) — the configuration example's 1 MHz software-serial
build driving the full protocol suite, proving the plumbing produces a
working loader and not just one that fits;
- `pureboot.usart1` (644A) — the same suite over the second hardware USART:
instance selection is compile-checked everywhere, but only a live session
proves the loader polls the USART it claims;
- `pureboot.mute` (328P) — a software link on USART0's own pins, entered from an
application that handed over with that USART still enabled: the loader must
still answer, which it does only because it releases it. The pin ownership is
the runner's, not simavr's — simavr wires a USART through IRQs and never takes
the pin from the port, so without that model the state under test could not
arise at all;
- `pureboot.dirty` (328P) — entering the loader from a running application over
an SPM buffer it deliberately dirtied, the case the loader declines to guard:
a bare verify must see the corruption and the repairing verify must fix it in
one rewrite. Hardware forbids the state here, but simavr dispatches SPM from
anywhere, which is what makes the path constructible;
- `pureboot.update` — the full `--update-loader` flow, then every power-fail
phase: the device is killed mid-write, restarted from its flash dump, and a
re-run must complete the update with the application intact;
- `pureboot.osccal` (328P, t85) — a loader built with the `OSCCAL` axis holds
the trim register at the built byte from its first prompt, observed through
the wire on one chip per addressing encoding (`sts` and low-I/O `out`);
- `pureboot.autobaud` (328P, 1284P) — the clock-free build over the GPIO⇄pty
bridge: the calibration handshake, a flash + EEPROM + fuse round trip against
the simulator's own memory, a data-space round trip, the hand-over — then the
same binary again at double the clock, which is the property the backend
exists for. The measured clock `--info` prints is asserted against the
simulator's exact clock, inside the unit encoding's own envelope, at both
points. A lone calibration pulse with no knock behind it must still let
the application boot, so no wait in activation can be unbounded.
`size`, `unit`, `pi`, `planner`, `scan` and `handshake` are host logic and run
anywhere; the simulator-driven targets need simavr and a pty, so they are
POSIX-only.
## Hardware
The suite above proves the protocol on every chip; it cannot prove a *board*.
Two things live only on silicon: an RC oscillator that is not on its nominal, and
a reset edge that has to come from somewhere. `tools/pbrig.py` and
`tools/pbhw.py` cover that, and know nothing per-board — every deployment fact
is a flag or a `PUREBOOT_*` environment variable.
```sh
export PUREBOOT_PROGRAMMER=atmelice_isp PUREBOOT_PART=t13 PUREBOOT_PORT=COM6
tools/pbrig.py backup rig-backup/ # verified, before anything is written
tools/pbhw.py --autobaud --loader build/ab.bin --app build/pbapp.hex --marker APP
```
`pbrig.py` is the primitives — `signature`, `reset`, `flash`, `fuses`, `backup`,
`rate` — and the module `pbhw.py` builds on. Two rig facts are encoded in it
because neither is guessable: an **ISP access is the reset edge** (the part runs
the moment the programmer releases it, which is the only edge available when the
adapter's DTR is not wired to reset, so a session begins with an ISP touch and
knocks immediately after), and **avrdude splits `-U` on colons**, so a Windows
path's drive letter breaks the spec and every file is passed as a bare name with
avrdude run in its own directory.
`pbrig.py rate` is the one that turns "the loader is silent, so the wiring must
be wrong" into a number. Against a fixture built with `PUREBOOT_HEARTBEAT` — a
*fixed* cycles-per-bit transmitter — it sweeps the host rate, and the band where
the marker still decodes brackets the part's true bit rate; with the clock the
image was built for, that is the clock the part is really running at. No
instrument beyond the adapter already attached. An ATtiny13A measured this way
came out at 9.072 MHz against its 9.6 MHz nominal, −5.5 % — inside the
datasheet's ±10 % and outside what an 8N1 frame survives, which is the whole
case for the autobaud backend on such a part.
`pbhw.py` takes its bounds from the info block the loader reports, so one run
covers a 1 KiB tiny and a 128 KiB mega alike: identity, the EEPROM round trip
and erase, an application flashed and verified and then *seen running*, the
application region read and erased, the loader slot proven intact across that
erase by an independent ISP read, and an oversized image refused. It overwrites
the application flash and EEPROM, which is why `backup` comes first.

617
pureboot/pureboot.cpp Normal file
View File

@@ -0,0 +1,617 @@
// pureboot — a serial bootloader on libavr: one C++ source, no inline
// assembly, no global register variables, a 512-byte slot on every chip
// libavr targets. The device speaks primitives; every composite (verify, erase,
// reset-vector surgery, self-update) lives in the host tool. Protocol,
// deployment and configuration: README.md next to this file.
//
// The image is position-independent — PC-relative control flow, wire
// addresses in, the write guard and the info block both anchored on the
// runtime return address — so the identical binary runs from any slot. That
// is what makes a copy one slot below able to rewrite the resident one, and
// every change here has to keep it (test/check_pi.py).
#include <chrono>
#include <libavr/libavr.hpp>
using namespace avr::literals;
namespace spm = avr::spm;
namespace ee = avr::eeprom;
namespace pureboot {
namespace {
// Purely polled: every interrupt guard folds to nothing.
constexpr auto off = avr::irq::guard_policy::unused;
constexpr std::uint8_t ack = '+';
// Deployment parameters come from the build (pureboot_add_loader()). The
// signature is not one of them: the chip database is the only universal
// source — a tiny13A cannot read its own signature row from code. An autobaud
// build carries no clock and no baud at all; it measures both.
#if !defined(PUREBOOT_AUTOBAUD) && (!defined(PUREBOOT_CLOCK_HZ) || !defined(PUREBOOT_BAUD))
#error \
"PUREBOOT_CLOCK_HZ and PUREBOOT_BAUD select this build's clock and baud — create loader targets with pureboot_add_loader(), or PUREBOOT_AUTOBAUD for a clock-free one (README.md)"
#endif
#if !defined(PUREBOOT_AUTOBAUD)
using dev = avr::device<{.clock = avr::hertz_t{PUREBOOT_CLOCK_HZ}}>;
constexpr avr::baud_t wire_baud{PUREBOOT_BAUD};
#endif
// The loader owns the top 512 bytes; a staging copy goes in the slot below.
// Chips without a hardware boot section — the tinies and the m48s, whose SPM
// runs from anywhere (Atmel-8271 §26) — keep the application's relocated
// reset vector in the word under the slot.
constexpr std::uint16_t slot_bytes = 512;
constexpr std::uint16_t page = spm::page_bytes;
constexpr bool boot_section = avr::hw::curated::has_boot_section();
// Past 64 KiB one bank of flash does not cover the chip, so a transfer's
// selector byte carries the bank and the wire address stays a byte address
// within it. 'J' is the exception: it is a word address everywhere, because
// that is what the hardware's own jump takes.
constexpr bool banked_flash = spm::flash_bytes > 65536;
// A compile-time window, so the whole EEPROM belongs to the application;
// re-timing a deployed loader is a self-update with a re-timed build. An
// autobaud build has no clock to convert seconds against and counts polls.
#if !defined(PUREBOOT_TIMEOUT)
#define PUREBOOT_TIMEOUT 8
#endif
constexpr std::uint8_t timeout_seconds = PUREBOOT_TIMEOUT;
#if !defined(PUREBOOT_AUTOBAUD_POLLS)
#define PUREBOOT_AUTOBAUD_POLLS 4000000
#endif
constexpr avr::uint24_t autobaud_budget = PUREBOOT_AUTOBAUD_POLLS;
// A build may bake a measured oscillator trim (README.md: the RC-oscillator
// deployment answer); the byte is applied at the top of run(). Orthogonal to
// the serial backend — an autobaud build may carry it for the application's
// benefit alone.
#if defined(PUREBOOT_OSCCAL)
static_assert(PUREBOOT_OSCCAL >= 0 && PUREBOOT_OSCCAL <= 0xff, "PUREBOOT_OSCCAL is one OSCCAL byte");
#endif
// The loader's one identity number. The protocol carries none of its own —
// a version implies it, and the host tool holds that map (README.md).
constexpr std::uint8_t version = 8;
// The image's identity stamp, for the host tool rather than for the wire: an
// update image is a bare 512-byte slot, and without this nothing in it says
// which chip it was built for. The tool refuses to install an image whose
// stamp does not match the device — flashing a foreign loader bricks the
// target, and the loader itself cannot check what has already replaced it.
//
// Never read from flash by the loader — 'b' answers out of this array, but at
// constant indices, so those fold to immediates and no runtime address of it
// is ever formed. `used` keeps the compiler from dropping the copy the host
// needs and `retain` keeps --gc-sections from collecting it.
// clang-format off
[[gnu::used, gnu::retain, gnu::section(".text.stamp")]]
inline constexpr std::uint8_t identity_stamp[]{
'P', 'B', // the magic the host scans an image for
version, // and from here on, exactly what 'b' answers
avr::hw::db.signature[0],
avr::hw::db.signature[1],
avr::hw::db.signature[2],
};
// clang-format on
// Where the identity proper starts: past the magic the host scans for.
constexpr std::uint8_t stamp_identity = 2;
// The address spaces a transfer can name, in a selector byte's low nibble.
// Flash is 0 so it is the cheapest to select.
//
// spm_ops is the one that is not memory: a write there hands its byte to
// SPMCSR and fires the instruction at the transfer's address, which is how
// page erase, page write and RWW re-enable reach the wire without the loader
// carrying a command for each. The hardware's four-cycle store-to-SPM window
// is why this is one fused primitive and not a poke of SPMCSR — no host can
// hit that window across a serial link.
enum : std::uint8_t { sp_flash = 0, sp_eeprom = 1, sp_data = 2, sp_fuse = 3, sp_spm = 4 };
// A selector's high nibble is the flash bank — the address bits above the
// 16-bit wire address, RAMPZ on the chips that have one. Keeping it here
// rather than widening the wire address is what lets one 16-bit cursor serve
// every space: a 24-bit cursor would pay its extra byte on EEPROM and data
// reads that can never need it.
[[gnu::always_inline]] inline std::uint8_t space_of(std::uint8_t selector)
{
return selector & 0x0f;
}
[[gnu::always_inline]] inline std::uint8_t bank_of(std::uint8_t selector)
{
return static_cast<std::uint8_t>(selector >> 4);
}
// The slot a flash address falls in, as one byte. A slot is half as many words
// as bytes, so the word address's high byte is exactly this index — which is
// what lets the write guard compare a single byte, and what the running copy's
// own return address yields for free.
constexpr std::uint8_t slot_shift = std::countr_zero(slot_bytes);
constexpr std::uint8_t bank_shift = 16 - slot_shift;
[[gnu::always_inline]] inline std::uint8_t slot_of([[maybe_unused]] std::uint8_t bank, std::uint16_t at)
{
const auto within = static_cast<std::uint8_t>(at >> slot_shift);
if constexpr (banked_flash)
return static_cast<std::uint8_t>((bank << bank_shift) | within);
else
return within;
}
// The serial link, per the build's PUREBOOT_USART / PUREBOOT_SOFT_SERIAL /
// PUREBOOT_AUTOBAUD, defaulting to the chip's USART0 where it has one. The
// software receiver is the polled one: the vector table belongs to the
// application. Templates on the clock, so only the selected backend
// instantiates. pending() is the cheap line test the activation window polls;
// drain() holds until the last frame is off the wire, so a hand-over cannot
// let the target's re-init clip the ack.
#if defined(PUREBOOT_SOFT_SERIAL) && defined(PUREBOOT_USART)
#error "PUREBOOT_SOFT_SERIAL and PUREBOOT_USART select opposing serial backends"
#endif
#if defined(PUREBOOT_AUTOBAUD) && defined(PUREBOOT_USART)
#error "PUREBOOT_AUTOBAUD measures a software link; it cannot drive a hardware USART"
#endif
#if defined(PUREBOOT_HALF_DUPLEX) && (defined(PUREBOOT_SOFT_SERIAL) || defined(PUREBOOT_AUTOBAUD))
#error "PUREBOOT_HALF_DUPLEX is the hardware USART's one-wire mode; a software link goes one-wire by RX == TX"
#endif
#if !defined(PUREBOOT_RX)
#define PUREBOOT_RX pb0
#endif
#if !defined(PUREBOOT_TX)
#define PUREBOOT_TX pb1
#endif
#if defined(PUREBOOT_USART)
constexpr int usart_unit = PUREBOOT_USART;
#else
constexpr int usart_unit = 0;
#endif
// One-wire on the hardware USART (PUREBOOT_HALF_DUPLEX): RXD and TXD tied
// together off-chip, exactly one direction enabled at a time — the library's
// .half_duplex turn-around. The activation window is unchanged; only its
// poll grows the release-line test rx_ready() carries in this mode.
constexpr bool hw_half_duplex =
#if defined(PUREBOOT_HALF_DUPLEX)
true;
#else
false;
#endif
template <avr::hertz_t C, avr::baud_t B>
struct hardware_link {
using uart = avr::uart::usart<usart_unit, C, {.baud = B, .max_baud_error = 2.5_pct, .half_duplex = hw_half_duplex}>;
// The compiled idle poll around the window's narrow (uint24_t) countdown:
// the RXC test, then sbiw + sbci + brne (5). The test's cost follows the
// status register's home — a 2-cycle bit-skip where UCSRnA sits in
// bit-addressable I/O (the classic megas), lds + skip (4) in extended
// I/O. Half-duplex polls through rx_ready()'s release-line test, which
// -Os outlines: the rcall (3), the UCSR#B read and not-taken skip with
// the jump over the write (I/O 3, extended 5), the ret (4) — and the
// call in the loop body pushes the countdown into call-saved registers,
// where the uint24_t step is ldi+sub+sbc+sbc (4) instead of sbiw+sbci
// (3). Measured off the built loops: 18 a poll in bit-addressable I/O,
// 22 in extended. A uint32_t countdown pays one more sbci —
// window_polls() adds it where the count forces the wide type. Held per
// chip by the pureboot.window gates. The lookup rides the baud parameter
// so it stays dependent: the trait is an incomplete type on the
// USART-less chips, which parse this template without ever instantiating
// it.
template <avr::baud_t Baud, typename U = avr::hw::usart_of<usart_unit>>
static consteval std::uint8_t poll_cost()
{
if (hw_half_duplex)
return U::ucsra::addr < 0x40 ? 18 : 22;
return U::ucsra::addr < 0x40 ? 7 : 9;
}
static constexpr std::uint8_t poll_cycles = poll_cost<B>();
static void init()
{
avr::init<uart>();
}
static bool pending()
{
return uart::rx_ready();
}
static std::uint8_t rx()
{
return uart::read_blocking();
}
static void tx(std::uint8_t byte)
{
uart::write(byte);
}
static void drain()
{
// A drain here always follows this link's own write — the frame is
// in flight by construction, so the completion the wait needs is
// guaranteed and the bounded default's countdown would be dead bytes.
uart::drain_unbounded();
}
};
template <avr::hertz_t C, avr::baud_t B>
struct software_link {
// RX == TX is the one-wire deployment: the transmitter becomes a guest
// on the receiver's pull-up line, taking the pin's direction for exactly
// one frame per byte.
using rx_t = avr::uart::software_rx_polled<C, avr::PUREBOOT_RX, B>;
using tx_t = avr::uart::software_tx<C, avr::PUREBOOT_TX, B, avr::PUREBOOT_RX == avr::PUREBOOT_TX>;
// The compiled idle poll around the window's narrow (uint24_t) countdown:
// sbis skipping the exit (2), sbiw + sbci + brne (5). A uint32_t
// countdown pays one more sbci — window_polls() adds it where the count
// forces the wide type. Held by the pureboot.window gate.
static constexpr std::uint8_t poll_cycles = 7;
static void init()
{
avr::init<rx_t, tx_t>();
}
static bool pending()
{
return rx_t::start_pending();
}
static std::uint8_t rx()
{
return rx_t::template read_blocking<off>();
}
static void tx(std::uint8_t byte)
{
tx_t::template write<off>(byte);
}
static void drain()
{
// The software transmitter returns only after the stop bit.
}
};
// The clock-free link: the bit period is measured from the host's calibration
// pulse instead of derived from a clock, so one image serves every F_CPU and
// every rate. Activation differs in kind from the other two — there is no
// clock to time a window against — so this backend brings its own, below.
struct autobaud_link {
// The unit in GPIOR2:GPIOR1 where the chip has them: the loader owns the
// whole chip while it runs, and the pair costs one word per access where
// the RAM word costs two — six words across the image.
using uart = avr::uart::software_autobaud<avr::PUREBOOT_RX, avr::PUREBOOT_TX, avr::uart::unit_home::gpior>;
static void init()
{
avr::init<uart>();
}
static std::uint8_t rx()
{
return uart::template read<off>();
}
static void tx(std::uint8_t byte)
{
uart::template write<off>(byte);
}
static void drain()
{
// A drain here always follows this link's own write — the frame is
// in flight by construction, so the completion the wait needs is
// guaranteed and the bounded default's countdown would be dead bytes.
uart::drain_unbounded();
}
};
#if defined(PUREBOOT_AUTOBAUD)
using link = autobaud_link;
#elif defined(PUREBOOT_USART)
static_assert(avr::uart::has_usart<usart_unit>(), "PUREBOOT_USART selects a hardware USART this chip does not have");
using link = hardware_link<dev::clock, wire_baud>;
#elif defined(PUREBOOT_SOFT_SERIAL)
using link = software_link<dev::clock, wire_baud>;
#else
using link = std::conditional_t<avr::uart::has_usart<usart_unit>(), hardware_link<dev::clock, wire_baud>,
software_link<dev::clock, wire_baud>>;
#endif
// The application's entry, pinned by the linker (--defsym): word 0 on a
// boot-sectioned mega, the trampoline at base − 2 elsewhere. Reaching it must
// not depend on where this copy runs, so the jump goes through a pointer, and
// [[gnu::noipa]] keeps the constant from folding back into a relative call.
extern "C" [[noreturn]] void pureboot_app();
[[gnu::noipa, noreturn]] void jump(void (*target)())
{
target();
__builtin_unreachable();
}
[[noreturn]] void run_app()
{
jump(pureboot_app);
}
// Activation: a bounded wait for the host, then the knock. Both forms boot the
// application when the window closes on an idle line, and both bound *every*
// wait — a knock awaited without a deadline would let one stray edge hold an
// unattended device in the loader forever.
#if defined(PUREBOOT_AUTOBAUD)
// The window is a fixed poll budget: with no clock, whole seconds cannot be
// timed. A uint24_t holds it — a fourth byte would cost two words at every
// countdown step for range never used.
void await_host()
{
for (;;) {
if (!link::uart::calibrate(autobaud_budget))
run_app();
// The calibration pulse has already proven a host is there, so one
// byte activates. A knock that never arrives falls back to calibrate(),
// whose own budget then boots the application.
if (link::uart::template read<off>(autobaud_budget) == 'p')
return;
}
}
#else
// The window as one countdown, divided by the backend's counted poll-loop
// cycles. Whole seconds is all it promises. The per-poll cost depends on the
// countdown's own width (a uint32_t decrement chain is one sbci longer), and
// the width depends on the poll count — solved narrow-first: a count that
// fits 24 bits at the narrow cost keeps the narrow loop, anything else takes
// the wide loop at its own cost. A count fitting 24 bits only at the wide
// cost stays wide, so the choice cannot oscillate on the boundary.
consteval std::uint32_t polls_at(std::uint32_t per_poll)
{
// Whole-window cycles first, then the per-poll division: one truncation
// instead of one per second. Same instructions either way — only the
// countdown's immediate moves.
return static_cast<std::uint32_t>(dev::cycles_for<std::chrono::seconds{timeout_seconds}>() / per_poll);
}
consteval bool narrow_window()
{
return polls_at(link::poll_cycles) <= 0xffffff;
}
consteval std::uint32_t window_polls()
{
return polls_at(narrow_window() ? link::poll_cycles : link::poll_cycles + 1u);
}
// The countdown in the narrowest type that holds it: a fourth byte would
// cost a wider decrement chain at every poll for range most windows never
// use (the autobaud budget makes the same choice).
using window_t = std::conditional_t<narrow_window(), avr::uint24_t, std::uint32_t>;
bool pending_before_deadline()
{
window_t polls = window_polls();
do {
if (link::pending())
return true;
} while (--polls);
return false;
}
// A knock byte under the deadline: an idle window means no host, so the
// application runs.
std::uint8_t rx_deadline()
{
if (!pending_before_deadline())
run_app();
return link::rx();
}
void await_host()
{
// 'p' then 'b', each under a fresh window; anything else is line noise.
while (rx_deadline() != 'p' || rx_deadline() != 'b') {
}
}
#endif
// Inlined: read across a call, the first byte strands in a call-saved
// register the caller has to push and pop.
[[gnu::always_inline]] inline std::uint16_t rx16()
{
std::uint16_t low = link::rx();
return static_cast<std::uint16_t>(low | (link::rx() << 8));
}
// The wire's byte pair as the word it is — AVR is little-endian too, so the
// cast is the identity a shift-and-or spelling makes the compiler rediscover.
// Callers read into named variables first: the wire order is a sequence of
// reads, not an argument order.
[[gnu::always_inline]] inline std::uint16_t word_of(std::array<std::uint8_t, 2> pair)
{
return std::bit_cast<std::uint16_t>(pair);
}
// Out of line: several sites send it, and a call is shorter than a
// load-immediate at each.
[[gnu::noinline]] void tx_ack()
{
link::tx(ack);
}
// A wire address and its selector's bank as the flash address they name.
[[gnu::always_inline]] inline spm::flash_address_t flash_address([[maybe_unused]] std::uint8_t bank, std::uint16_t at)
{
if constexpr (banked_flash)
return (static_cast<spm::flash_address_t>(bank) << 16) | at;
else
return at;
}
// One byte out of any space. Every accessor shares the transfer's cursor, its
// loop and its call site, so a space costs only its own instruction rather
// than a body, a loop and a dispatch arm of its own.
[[gnu::always_inline]] inline std::uint8_t load(std::uint8_t space, [[maybe_unused]] std::uint8_t bank,
std::uint16_t at)
{
if (space == sp_eeprom)
return ee::read(at);
if (space == sp_data)
return *reinterpret_cast<volatile std::uint8_t *>(at);
if (space == sp_fuse)
return spm::read_fuse<off>(static_cast<spm::fuse>(at));
if constexpr (banked_flash)
return avr::flash_load_far<std::uint8_t>(flash_address(bank, at));
else
return avr::flash_load(reinterpret_cast<const std::uint8_t *>(at));
}
// One byte into a writable space. Flash is not one of them — it arrives a
// page at a time through 'W' and is committed through sp_spm — and the fuses
// are not writable at all: SPM reaches flash and boot lock bits only.
[[gnu::always_inline]] inline void store(std::uint8_t space, std::uint8_t bank, std::uint16_t at, std::uint8_t value,
std::uint8_t slot_high)
{
if (space == sp_data) {
*reinterpret_cast<volatile std::uint8_t *>(at) = value;
return;
}
if (space == sp_spm) {
// The running-slot write guard. An SPM command aimed at the slot this
// code executes from is dropped, so a broken host cannot brick the
// running loader — while a copy one slot lower may still rewrite the
// resident one, which is what a self-update is. Guarding the commit
// rather than the page fill covers erase and write both, and leaves a
// refused page's words in the buffer: harmless, since the next page
// write auto-erases it (§26.2.1).
if (slot_of(bank, at) != slot_high)
spm::command<off>(value, flash_address(bank, at));
// Only a boot-sectioned mega runs on while its RWW section programs;
// everywhere else the CPU halts through erase and write, so the wait
// is already over by the time it returns.
if constexpr (boot_section)
spm::wait();
return;
}
// Host-paced: the ack goes out once the write has begun, so the next byte
// arrives while it completes and nothing is missed without a buffer.
ee::write<off>(at, value);
}
// One page into the SPM buffer, and only that: the erase and the write that
// commit it are host-issued sp_spm stores, which reach the same fused
// store-and-SPM pair through the transfer path's own address and data.
//
// Nothing discards the buffer first: it is write-once per word (§26.2.1), so
// filling over a refused page or an application's leavings programs stale
// words — but a page write auto-erases it (§26.2.1; §19.2 on the tinies), so
// that write clears the condition and the host's read-back rewrites the page.
void fill_page(std::uint8_t bank, std::uint16_t at)
{
// The address names a page, so its in-page bits are dropped and the walk
// starts at the page base; the low byte of the cursor is the whole in-page
// offset, since a page is aligned and never crosses a bank.
std::uint16_t z = at & ~static_cast<std::uint16_t>(page - 1);
do {
std::uint8_t low = link::rx();
std::uint8_t high = link::rx();
spm::fill<off>(flash_address(bank, z), word_of({low, high}));
z += 2;
} while (static_cast<std::uint8_t>(z) & (page - 1));
}
[[noreturn]] void run()
{
#if defined(PUREBOOT_OSCCAL)
// The build's oscillator trim, ahead of everything — the WDRF bail
// included — so every path out of reset, the watchdog hand-over to the
// application first among them, runs on the corrected clock.
avr::clock::calibrate(PUREBOOT_OSCCAL);
#endif
// A watchdog reset belongs to the application, whose watchdog stays forced
// on until it clears WDRF — no activation window in its way.
if (avr::power::peek_reset_cause().watchdog)
run_app();
link::init();
// The slot this copy runs in, which the write guard follows: the return
// address is a word address and a slot is half as many words as bytes, so
// its high byte is the slot index outright. No absolute address is ever
// formed, so the image stays position-independent.
const auto slot_high = avr::startup::caller_page();
await_host();
for (;;) {
// No prompt while an EEPROM write runs: it blocks SPM and fuse reads
// (§26.2.1), and the prompt is the previous command's completion ack.
ee::wait();
tx_ack();
const std::uint8_t command = link::rx();
switch (command) {
case 'b': // identity: the version, then the three signature bytes
// Straight out of the stamp, so the wire and the image can never
// disagree about what this loader is. The indices are constant and
// the array is constexpr, so these are immediates, not flash reads:
// nothing here needs the stamp's runtime address.
for (std::uint8_t at = stamp_identity; at != sizeof identity_stamp; ++at)
link::tx(identity_stamp[at]);
break;
case 'J': // jump: sel8 (reserved), addr16 as a wire word address
case 'W': // fill one flash page buffer: sel8, addr16, then page bytes
case 'G': // read: sel8, addr16, n8 (0 = 256)
case 'g': { // write: sel8, addr16, n8, then n bytes, each acked
// One decode, one cursor and one loop for every space, both
// directions and the jump: a command per memory would carry a copy
// of all three each. 'J' — the hand-over and staging transfer —
// carries a selector it ignores so its address rides the same two
// reads as everything else; 'W' joins the same decode rather than
// keeping an address form of its own, so flash addressing is
// uniform across every command that names it.
const std::uint8_t selector = link::rx();
const std::uint8_t space = space_of(selector);
const std::uint8_t bank = bank_of(selector);
std::uint16_t at = rx16();
if (command == 'J') {
tx_ack();
link::drain();
jump(reinterpret_cast<void (*)()>(at));
}
if (command == 'W') {
fill_page(bank, at);
break;
}
std::uint8_t count = link::rx();
do {
// Read and write are one letter apart in case, so the direction
// is a single bit and the loop picks it with a one-word skip.
if (command & 0x20) {
store(space, bank, at, link::rx(), slot_high);
tx_ack();
} else
link::tx(load(space, bank, at));
++at;
} while (--count);
break;
}
default: // unknown bytes are ignored; the loop re-acks
break;
}
}
}
} // namespace
} // namespace pureboot
// stack::hardware: activation is reset-only, so the reset logic's own
// SP = RAMEND stands wherever the datasheet guarantees it (the classic
// megas still get the write); a 'J' entry runs on the caller's live stack.
template struct avr::startup::entry<pureboot::run, avr::startup::stack::hardware>;

1766
pureboot/pureboot.py Normal file
View File

File diff suppressed because it is too large Load Diff

5
stk500v2/clock.hpp
View File

@@ -1,5 +0,0 @@
#pragma once
//#define F_CPU 18'432'000
#define F_CPU 16'000'000
#include <util/delay.h>

113
stk500v2/command.hpp
View File

@@ -1,113 +0,0 @@
#pragma once
#include <stdint.h>
//////////////////////////////////////////////////////////////////////////
// STK message constants
static constexpr uint8_t MESSAGE_START = 0x1B; // ASCII ESC
static constexpr uint8_t TOKEN = 0x0E;
//////////////////////////////////////////////////////////////////////////
// STK general command constants
static constexpr uint8_t CMD_SIGN_ON = 0x01;
static constexpr uint8_t CMD_SET_PARAMETER = 0x02;
static constexpr uint8_t CMD_GET_PARAMETER = 0x03;
static constexpr uint8_t CMD_SET_DEVICE_PARAMETERS = 0x04;
static constexpr uint8_t CMD_OSCCAL = 0x05;
static constexpr uint8_t CMD_LOAD_ADDRESS = 0x06;
static constexpr uint8_t CMD_FIRMWARE_UPGRADE = 0x07;
//////////////////////////////////////////////////////////////////////////
// STK ISP command constants
static constexpr uint8_t CMD_ENTER_PROGMODE_ISP = 0x10;
static constexpr uint8_t CMD_LEAVE_PROGMODE_ISP = 0x11;
static constexpr uint8_t CMD_CHIP_ERASE_ISP = 0x12;
static constexpr uint8_t CMD_PROGRAM_FLASH_ISP = 0x13;
static constexpr uint8_t CMD_READ_FLASH_ISP = 0x14;
static constexpr uint8_t CMD_PROGRAM_EEPROM_ISP = 0x15;
static constexpr uint8_t CMD_READ_EEPROM_ISP = 0x16;
static constexpr uint8_t CMD_PROGRAM_FUSE_ISP = 0x17;
static constexpr uint8_t CMD_READ_FUSE_ISP = 0x18;
static constexpr uint8_t CMD_PROGRAM_LOCK_ISP = 0x19;
static constexpr uint8_t CMD_READ_LOCK_ISP = 0x1A;
static constexpr uint8_t CMD_READ_SIGNATURE_ISP = 0x1B;
static constexpr uint8_t CMD_READ_OSCCAL_ISP = 0x1C;
static constexpr uint8_t CMD_SPI_MULTI = 0x1D;
//////////////////////////////////////////////////////////////////////////
// STK PP command constants
static constexpr uint8_t CMD_ENTER_PROGMODE_PP = 0x20;
static constexpr uint8_t CMD_LEAVE_PROGMODE_PP = 0x21;
static constexpr uint8_t CMD_CHIP_ERASE_PP = 0x22;
static constexpr uint8_t CMD_PROGRAM_FLASH_PP = 0x23;
static constexpr uint8_t CMD_READ_FLASH_PP = 0x24;
static constexpr uint8_t CMD_PROGRAM_EEPROM_PP = 0x25;
static constexpr uint8_t CMD_READ_EEPROM_PP = 0x26;
static constexpr uint8_t CMD_PROGRAM_FUSE_PP = 0x27;
static constexpr uint8_t CMD_READ_FUSE_PP = 0x28;
static constexpr uint8_t CMD_PROGRAM_LOCK_PP = 0x29;
static constexpr uint8_t CMD_READ_LOCK_PP = 0x2A;
static constexpr uint8_t CMD_READ_SIGNATURE_PP = 0x2B;
static constexpr uint8_t CMD_READ_OSCCAL_PP = 0x2C;
static constexpr uint8_t CMD_SET_CONTROL_STACK = 0x2D;
//////////////////////////////////////////////////////////////////////////
// STK HVSP command constants
static constexpr uint8_t CMD_ENTER_PROGMODE_HVSP = 0x30;
static constexpr uint8_t CMD_LEAVE_PROGMODE_HVSP = 0x31;
static constexpr uint8_t CMD_CHIP_ERASE_HVSP = 0x32;
static constexpr uint8_t CMD_PROGRAM_FLASH_HVSP = 0x33;
static constexpr uint8_t CMD_READ_FLASH_HVSP = 0x34;
static constexpr uint8_t CMD_PROGRAM_EEPROM_HVSP = 0x35;
static constexpr uint8_t CMD_READ_EEPROM_HVSP = 0x36;
static constexpr uint8_t CMD_PROGRAM_FUSE_HVSP = 0x37;
static constexpr uint8_t CMD_READ_FUSE_HVSP = 0x38;
static constexpr uint8_t CMD_PROGRAM_LOCK_HVSP = 0x39;
static constexpr uint8_t CMD_READ_LOCK_HVSP = 0x3A;
static constexpr uint8_t CMD_READ_SIGNATURE_HVSP = 0x3B;
static constexpr uint8_t CMD_READ_OSCCAL_HVSP = 0x3C;
//////////////////////////////////////////////////////////////////////////
// STK status constants
// Success
static constexpr uint8_t STATUS_CMD_OK = 0x00;
// Warnings
static constexpr uint8_t STATUS_CMD_TOUT = 0x80;
static constexpr uint8_t STATUS_RDY_BSY_TOUT = 0x81;
static constexpr uint8_t STATUS_SET_PARAM_MISSING = 0x82;
// Errors
static constexpr uint8_t STATUS_CMD_FAILED = 0xC0;
static constexpr uint8_t STATUS_CKSUM_ERROR = 0xC1;
static constexpr uint8_t STATUS_CMD_UNKNOWN = 0xC9;
//////////////////////////////////////////////////////////////////////////
// STK parameter constants
static constexpr uint8_t PARAM_BUILD_NUMBER_LOW = 0x80;
static constexpr uint8_t PARAM_BUILD_NUMBER_HIGH = 0x81;
static constexpr uint8_t PARAM_HW_VER = 0x90;
static constexpr uint8_t PARAM_SW_MAJOR = 0x91;
static constexpr uint8_t PARAM_SW_MINOR = 0x92;
static constexpr uint8_t PARAM_VTARGET = 0x94;
static constexpr uint8_t PARAM_VADJUST = 0x95;
static constexpr uint8_t PARAM_OSC_PSCALE = 0x96;
static constexpr uint8_t PARAM_OSC_CMATCH = 0x97;
static constexpr uint8_t PARAM_SCK_DURATION = 0x98;
static constexpr uint8_t PARAM_TOPCARD_DETECT = 0x9A;
static constexpr uint8_t PARAM_STATUS = 0x9C;
static constexpr uint8_t PARAM_DATA = 0x9D;
static constexpr uint8_t PARAM_RESET_POLARITY = 0x9E;
static constexpr uint8_t PARAM_CONTROLLER_INIT = 0x9F;
//////////////////////////////////////////////////////////////////////////
// STK answer constants
static constexpr uint8_t ANSWER_CKSUM_ERROR = 0xB0;

1
stk500v2/flash

Submodule stk500v2/flash deleted from 6edb2e5a21

1
stk500v2/io

Submodule stk500v2/io deleted from 80de36ee7e

667
stk500v2/main.cpp
View File

@@ -1,667 +0,0 @@
#include "clock.hpp"
#include "stk500v2.hpp"
#include "uart/uart.hpp"
#include <math.h>
#include <avr/boot.h>
#include <avr/interrupt.h>
#include <avr/io.h>
#include <avr/pgmspace.h>
#include "command.hpp"
static constexpr auto TIMEOUT = 5000;
static constexpr auto BAUD_RATE = 115200;
using uart_interface = uart::Hardware0<uart::Config<BAUD_RATE>, uart::Driven::BLOCKING>;
uart::Uart<uart_interface> serial;
struct Message {
uint8_t start;
uint8_t number;
uint16_t size;
uint8_t token;
uint8_t body[275];
uint8_t checksum;
};
static inline bool receiveByte(uint8_t &data, uint16_t &timeout)
{
constexpr auto MICROSECOND = 1000.0 * 1000;
constexpr auto SYMBOL_SIZE = 9;
constexpr auto BYTE_DELAY_US = (SYMBOL_SIZE * MICROSECOND) / BAUD_RATE;
constexpr auto NUM_MS_DELAY_STEPS = static_cast<uint16_t>(round(1000 / BYTE_DELAY_US));
uint16_t msDelay = NUM_MS_DELAY_STEPS;
while (timeout) {
if (serial.rxByte(data)) {
timeout = TIMEOUT;
return true;
}
_delay_us(BYTE_DELAY_US);
if (--msDelay == 0) {
msDelay = NUM_MS_DELAY_STEPS;
--timeout;
}
}
return false;
}
static inline uint8_t calcChecksum(const Message &msg)
{
uint8_t checksum = msg.start;
for (uint16_t i = 1; i < 5 + msg.size; ++i) {
checksum ^= *(reinterpret_cast<const uint8_t *>(&msg) + i);
}
return checksum;
}
static inline bool receiveMessage(Message &msg, uint16_t &timeout)
{
if (!receiveByte(msg.start, timeout) || msg.start != MESSAGE_START)
return false;
if (!receiveByte(msg.number, timeout))
return false;
if (!receiveByte(*(reinterpret_cast<uint8_t *>(&msg.size) + 1), timeout))
return false;
if (!receiveByte(*reinterpret_cast<uint8_t *>(&msg.size), timeout) || msg.size > sizeof(msg.body))
return false;
if (!receiveByte(msg.token, timeout) || msg.token != TOKEN)
return false;
for (uint16_t i = 0; i < msg.size; ++i) {
if (!receiveByte(msg.body[i], timeout))
return false;
}
if (!receiveByte(msg.checksum, timeout) || msg.checksum != calcChecksum(msg))
return false;
return true;
}
static inline void transmitMessage(const Message &msg)
{
serial.txByte(msg.start);
serial.txByte(msg.number);
serial.txByte(msg.size >> 8);
serial.txByte(msg.size & 0xFF);
serial.txByte(msg.token);
for (uint16_t i = 0; i < msg.size; ++i)
serial.txByte(msg.body[i]);
serial.txByte(msg.checksum);
}
static inline bool isSignOn(const Message &msg)
{
if (msg.size == 1 && msg.body[0] == CMD_SIGN_ON)
return true;
return false;
}
static inline bool isGetParameter(const Message &msg)
{
if (msg.size == 2 && msg.body[0] == CMD_GET_PARAMETER)
return true;
return false;
}
static inline bool isSetParameter(const Message &msg)
{
if (msg.size == 3 && msg.body[0] == CMD_SET_PARAMETER)
return true;
return false;
}
static inline bool isEnterProgmodeIsp(const Message &msg)
{
if (msg.size == 12 && msg.body[0] == CMD_ENTER_PROGMODE_ISP)
return true;
return false;
}
static inline bool isReadSignatureIsp(const Message &msg)
{
if (msg.size == 6 && msg.body[0] == CMD_READ_SIGNATURE_ISP)
return true;
return false;
}
static inline bool isReadFuseIsp(const Message &msg)
{
if (msg.size == 6 && msg.body[0] == CMD_READ_FUSE_ISP)
return true;
return false;
}
static inline bool isReadLockIsp(const Message &msg)
{
if (msg.size == 6 && msg.body[0] == CMD_READ_LOCK_ISP)
return true;
return false;
}
static inline bool isLoadAddress(const Message &msg)
{
if (msg.size == 5 && msg.body[0] == CMD_LOAD_ADDRESS)
return true;
return false;
}
static inline bool isReadFlashIsp(const Message &msg)
{
if (msg.size == 4 && msg.body[0] == CMD_READ_FLASH_ISP)
return true;
return false;
}
static inline bool isReadEepromIsp(const Message &msg)
{
if (msg.size == 4 && msg.body[0] == CMD_READ_EEPROM_ISP)
return true;
return false;
}
static inline bool isChipEraseIsp(const Message &msg)
{
if (msg.size == 7 && msg.body[0] == CMD_CHIP_ERASE_ISP)
return true;
return false;
}
static inline bool isProgramFlashIsp(const Message &msg)
{
if (msg.body[0] == CMD_PROGRAM_FLASH_ISP) {
const auto dataSize = static_cast<uint16_t>(msg.body[1]) << 8 | msg.body[2];
if (msg.size == (dataSize + 10) && dataSize == SPM_PAGESIZE)
return true;
}
return false;
}
static inline bool isProgramEepromIsp(const Message &msg)
{
if (msg.body[0] == CMD_PROGRAM_EEPROM_ISP) {
if (msg.size == (static_cast<uint16_t>(msg.body[1]) << 8 | msg.body[2]) + 10)
return true;
}
return false;
}
static inline bool isLeaveProgmodeIsp(const Message &msg)
{
if (msg.size == 3 && msg.body[0] == CMD_LEAVE_PROGMODE_ISP)
return true;
return false;
}
static inline void formatSignOnAnswer(Message &msg)
{
msg.size = 3 + 8;
msg.body[1] = STATUS_CMD_OK;
msg.body[2] = 8;
msg.body[3] = 'S';
msg.body[4] = 'T';
msg.body[5] = 'K';
msg.body[6] = '5';
msg.body[7] = '0';
msg.body[8] = '0';
msg.body[9] = '_';
msg.body[10] = '2';
msg.checksum = calcChecksum(msg);
}
static inline void formatGetParameterAnswer(Message &msg)
{
msg.size = 3;
if (msg.body[1] == PARAM_HW_VER) {
msg.body[2] = 1;
} else if (msg.body[1] == PARAM_SW_MAJOR) {
msg.body[2] = 0x02;
} else if (msg.body[1] == PARAM_SW_MINOR) {
msg.body[2] = 0x0a;
} else if (msg.body[1] == PARAM_SCK_DURATION) {
msg.body[2] = 2;
} else if (msg.body[1] == PARAM_VADJUST) {
msg.body[2] = 25;
} else if (msg.body[1] == PARAM_VTARGET) {
msg.body[2] = 49;
} else if (msg.body[1] == PARAM_OSC_PSCALE) {
msg.body[2] = 2;
} else if (msg.body[1] == PARAM_OSC_CMATCH) {
msg.body[2] = 127;
} else if (msg.body[1] == PARAM_TOPCARD_DETECT) {
msg.body[2] = 0xFF;
} else {
msg.size = 2;
}
if (msg.size == 2) {
msg.body[1] = STATUS_CMD_FAILED;
} else {
msg.body[1] = STATUS_CMD_OK;
}
msg.checksum = calcChecksum(msg);
}
static inline void formatSetParameterAnswer(Message &msg)
{
msg.size = 2;
msg.body[1] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatEnterProgmodeIspAnswer(Message &msg)
{
msg.size = 2;
msg.body[1] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatReadSignatureIspAnswer(Message &msg)
{
msg.size = 4;
msg.body[2] = boot_signature_byte_get(msg.body[4] * 2);
msg.body[1] = STATUS_CMD_OK;
msg.body[3] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatReadFuseIspAnswer(Message &msg)
{
constexpr auto READ_LOW_FUSE_BITS = 0x0050;
constexpr auto READ_HIGH_FUSE_BITS = 0x0858;
constexpr auto READ_EXTENDED_FUSE_BITS = 0x0850;
msg.size = 4;
if (*reinterpret_cast<uint16_t *>(msg.body + 2) == READ_EXTENDED_FUSE_BITS) {
msg.body[2] = boot_lock_fuse_bits_get(GET_EXTENDED_FUSE_BITS);
}
if (*reinterpret_cast<uint16_t *>(msg.body + 2) == READ_HIGH_FUSE_BITS) {
msg.body[2] = boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS);
}
if (*reinterpret_cast<uint16_t *>(msg.body + 2) == READ_LOW_FUSE_BITS) {
msg.body[2] = boot_lock_fuse_bits_get(GET_LOW_FUSE_BITS);
}
msg.body[1] = STATUS_CMD_OK;
msg.body[3] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatReadLockIspAnswer(Message &msg)
{
msg.size = 4;
msg.body[2] = boot_lock_fuse_bits_get(GET_LOCK_BITS);
msg.body[1] = STATUS_CMD_OK;
msg.body[3] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatLoadAddressAnswer(Message &msg)
{
msg.size = 2;
msg.body[1] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatReadFlashIspAnswer(Message &msg, uint32_t &addr)
{
const uint16_t byteAddress = 2 * addr;
const uint16_t numBytes = static_cast<uint16_t>(msg.body[1]) << 8 | msg.body[2];
msg.size = 3 + numBytes;
msg.body[1] = STATUS_CMD_OK;
for (uint16_t i = 0; i < numBytes; ++i) {
msg.body[i + 2] = pgm_read_byte(static_cast<uint16_t>(byteAddress + i));
}
const auto numWords = numBytes / 2;
addr += numWords;
msg.body[numBytes + 2] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
namespace {
bool isEepromReady()
{
return (EECR & (1 << EEPE)) ? false : true;
}
void waitEepromReady()
{
while (!isEepromReady())
;
}
uint8_t readEepromByte(const uint8_t *addr)
{
EEAR = reinterpret_cast<uint16_t>(addr);
EECR |= (1 << EERE);
return EEDR;
}
void writeEepromByte(uint8_t *addr, uint8_t value)
{
EECR = 0;
EEAR = reinterpret_cast<uint16_t>(addr);
EEDR = value;
EECR |= (1 << EEMPE);
EECR |= (1 << EEPE);
}
//////////////////////////////////////////////////////////////////////////
void writeFlashPage(uint32_t pageAddress, const uint8_t *data)
{
boot_page_erase(pageAddress);
boot_spm_busy_wait();
for (uint16_t i = 0; i < SPM_PAGESIZE; i += 2) {
uint16_t dataWord = *data++;
dataWord |= (*data++) << 8;
boot_page_fill(pageAddress + i, dataWord);
}
boot_page_write(pageAddress);
boot_spm_busy_wait();
boot_rww_enable();
}
} // namespace
static inline uint16_t getBootloaderSize()
{
const auto highFuse = boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS);
constexpr auto BOOTSZ0 = 1;
constexpr auto BOOTSZ1 = 2;
if (highFuse & (1 << BOOTSZ1) && highFuse & (1 << BOOTSZ0))
return 256 * 2;
else if (highFuse & (1 << BOOTSZ1))
return 512 * 2;
else if (highFuse & (1 << BOOTSZ0))
return 1024 * 2;
return 2048 * 2;
}
static inline uint32_t getFlashSize()
{
const auto bootloaderSize = getBootloaderSize();
return (FLASHEND - bootloaderSize + 1);
}
static inline void performChipErase(uint16_t flashStartAddress = 0x0000)
{
constexpr auto getEepromEraseFuseBit = []() -> bool {
constexpr auto EESAVE = 3;
return boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS) & (1 << EESAVE);
};
constexpr auto eraseFlash = [](const uint16_t &flashStartAddress) {
const auto flashSize = getFlashSize();
const auto byteAddress = 2 * flashStartAddress;
for (uint16_t i = byteAddress; i < flashSize; i += SPM_PAGESIZE) {
boot_page_erase(i);
boot_spm_busy_wait();
}
boot_rww_enable();
};
constexpr auto eraseEeprom = [getEepromEraseFuseBit]() {
const auto eraseEeprom = getEepromEraseFuseBit();
if (eraseEeprom) {
constexpr auto EEPROM_SIZE = E2END + 1;
for (uint16_t i = 0; i < EEPROM_SIZE; ++i) {
writeEepromByte(reinterpret_cast<uint8_t *>(i), 0xFF);
waitEepromReady();
}
}
};
eraseFlash(flashStartAddress);
eraseEeprom();
}
static inline void formatChipEraseIspAnswer(Message &msg)
{
msg.size = 2;
msg.body[1] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatReadEepromIspAnswer(Message &msg, uint32_t &addr)
{
const uint16_t numBytes = static_cast<uint16_t>(msg.body[1]) << 8 | msg.body[2];
msg.size = 3 + numBytes;
msg.body[1] = STATUS_CMD_OK;
for (uint16_t i = 0; i < numBytes; ++i) {
msg.body[i + 2] = readEepromByte(reinterpret_cast<const uint8_t *>(addr + i));
}
addr += numBytes;
msg.body[numBytes + 2] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatProgramFlashIspAnswer(Message &msg, uint32_t &addr)
{
const auto byteAddress = 2 * addr;
if (byteAddress < getFlashSize())
writeFlashPage(byteAddress, msg.body + 10);
const uint16_t numBytes = static_cast<uint16_t>(msg.body[1]) << 8 | msg.body[2];
const auto numWords = numBytes / 2;
addr += numWords;
msg.size = 2;
msg.body[1] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatProgramEepromIspAnswer(Message &msg, uint32_t &addr)
{
const uint16_t numBytes = static_cast<uint16_t>(msg.body[1]) << 8 | msg.body[2];
for (uint16_t i = 0; i < numBytes; ++i) {
writeEepromByte(reinterpret_cast<uint8_t *>(addr + i), msg.body[10 + i]);
waitEepromReady();
}
addr += numBytes;
msg.size = 2;
msg.body[1] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatLeaveProgmodeIspAnswer(Message &msg)
{
msg.size = 2;
msg.body[1] = STATUS_CMD_OK;
msg.checksum = calcChecksum(msg);
}
static inline void formatErrorAnswer(Message &msg)
{
msg.start = MESSAGE_START;
msg.size = 1;
msg.token = TOKEN;
msg.body[0] = STATUS_CMD_UNKNOWN;
msg.checksum = calcChecksum(msg);
}
enum class ChipEraseState {
NONE = 0,
REQUEST = (1 << 1),
RESPONSE = (1 << 2),
PERFORM = REQUEST | RESPONSE,
PROGRAM = (1 << 3),
FINISH = REQUEST | RESPONSE | PROGRAM,
};
constexpr ChipEraseState operator|(const ChipEraseState &self, const ChipEraseState &other)
{
return static_cast<ChipEraseState>(static_cast<uint8_t>(self) | static_cast<uint8_t>(other));
}
constexpr ChipEraseState &operator|=(ChipEraseState &self, const ChipEraseState &other)
{
self = self | other;
return self;
}
static inline void handleMessage(Message &msg, uint32_t &addr, uint16_t &finishEraseAddress,
ChipEraseState &chipEraseFlag)
{
if (isSignOn(msg))
formatSignOnAnswer(msg);
else if (isGetParameter(msg))
formatGetParameterAnswer(msg);
else if (isSetParameter(msg))
formatSetParameterAnswer(msg);
else if (isEnterProgmodeIsp(msg))
formatEnterProgmodeIspAnswer(msg);
else if (isReadSignatureIsp(msg))
formatReadSignatureIspAnswer(msg);
else if (isReadFuseIsp(msg))
formatReadFuseIspAnswer(msg);
else if (isReadLockIsp(msg))
formatReadLockIspAnswer(msg);
else if (isLoadAddress(msg)) {
addr = msg.body[1];
addr = (addr << 8) | msg.body[2];
addr = (addr << 8) | msg.body[3];
addr = (addr << 8) | msg.body[4];
formatLoadAddressAnswer(msg);
} else if (isReadFlashIsp(msg))
formatReadFlashIspAnswer(msg, addr);
else if (isReadEepromIsp(msg))
formatReadEepromIspAnswer(msg, addr);
else if (isChipEraseIsp(msg)) {
chipEraseFlag |= ChipEraseState::REQUEST;
formatChipEraseIspAnswer(msg);
} else if (isProgramFlashIsp(msg)) {
chipEraseFlag |= ChipEraseState::PROGRAM;
formatProgramFlashIspAnswer(msg, addr);
finishEraseAddress = addr;
} else if (isProgramEepromIsp(msg))
formatProgramEepromIspAnswer(msg, addr);
else if (isLeaveProgmodeIsp(msg)) {
chipEraseFlag |= ChipEraseState::RESPONSE;
formatLeaveProgmodeIspAnswer(msg);
} else
formatErrorAnswer(msg);
transmitMessage(msg);
}
static inline void interfaceTest()
{
constexpr auto onSignOn = []() {};
constexpr auto onSetParam = []() {};
constexpr auto onGetParam = [](stk500v2::Param param, uint8_t &result) {
using stk500v2::Param;
switch (param) {
case Param::HW_VER:
result = 1;
break;
case Param::SW_MAJOR:
result = 2;
break;
case Param::SW_MINOR:
result = 10;
break;
case Param::SCK_DURATION:
result = 2;
break;
case Param::VADJUST:
result = 25;
break;
case Param::VTARGET:
result = 49;
break;
case Param::OSC_PSCALE:
result = 2;
break;
case Param::OSC_CMATCH:
result = 127;
break;
case Param::TOPCARD_DETECT:
result = 0xFF;
break;
default:
return false;
}
return true;
};
constexpr auto callbacks = stk500v2::Callbacks<onSignOn, onSetParam, onGetParam>();
stk500v2::Stk500v2<uart_interface, TIMEOUT, callbacks> stk500;
stk500.init();
while (stk500.callback())
;
}
int main()
{
/*interfaceTest();
return 0;*/
serial.init();
Message msg;
uint32_t addr = 0x0000;
uint16_t finishEraseAddress = 0x0000;
ChipEraseState chipEraseFlag = ChipEraseState::NONE;
uint16_t timeout = TIMEOUT;
while (true) {
if (receiveMessage(msg, timeout)) {
handleMessage(msg, addr, finishEraseAddress, chipEraseFlag);
}
if (timeout == 0) {
if (chipEraseFlag == ChipEraseState::PERFORM) {
performChipErase();
chipEraseFlag = ChipEraseState::NONE;
} else if (chipEraseFlag == ChipEraseState::FINISH) {
performChipErase(finishEraseAddress);
chipEraseFlag = ChipEraseState::NONE;
}
asm volatile("jmp 0x0000");
}
}
return 0;
}
void startup() __attribute__((naked, section(".vectors")));
void startup()
{
asm volatile("clr __zero_reg__");
SP = RAMEND;
SREG = 0;
asm volatile("jmp main");
}

275
stk500v2/stk500v2.cppproj
View File

@@ -1,275 +0,0 @@
<?xml version="1.0" encoding="utf-8"?>
<Project DefaultTargets="Build" xmlns="http://schemas.microsoft.com/developer/msbuild/2003" ToolsVersion="14.0">
<PropertyGroup>
<SchemaVersion>2.0</SchemaVersion>
<ProjectVersion>7.0</ProjectVersion>
<ToolchainName>com.Atmel.AVRGCC8.CPP</ToolchainName>
<ProjectGuid>{19798cce-5d96-40e9-b769-d209715dce0c}</ProjectGuid>
<avrdevice>ATmega328P</avrdevice>
<avrdeviceseries>none</avrdeviceseries>
<OutputType>Executable</OutputType>
<Language>CPP</Language>
<OutputFileName>$(MSBuildProjectName)</OutputFileName>
<OutputFileExtension>.elf</OutputFileExtension>
<OutputDirectory>$(MSBuildProjectDirectory)\$(Configuration)</OutputDirectory>
<AssemblyName>stk500v2</AssemblyName>
<Name>stk500v2</Name>
<RootNamespace>stk500v2</RootNamespace>
<ToolchainFlavour>avr-g++-10.0.1</ToolchainFlavour>
<KeepTimersRunning>true</KeepTimersRunning>
<OverrideVtor>false</OverrideVtor>
<CacheFlash>true</CacheFlash>
<ProgFlashFromRam>true</ProgFlashFromRam>
<RamSnippetAddress>0x20000000</RamSnippetAddress>
<UncachedRange />
<preserveEEPROM>true</preserveEEPROM>
<OverrideVtorValue>exception_table</OverrideVtorValue>
<BootSegment>2</BootSegment>
<ResetRule>0</ResetRule>
<eraseonlaunchrule>0</eraseonlaunchrule>
<EraseKey />
<avrtool>com.atmel.avrdbg.tool.atmelice</avrtool>
<avrtoolserialnumber>J41800099437</avrtoolserialnumber>
<avrdeviceexpectedsignature>0x1E950F</avrdeviceexpectedsignature>
<com_atmel_avrdbg_tool_stk500>
<ToolOptions>
<InterfaceProperties>
<IspClock>125000</IspClock>
</InterfaceProperties>
<InterfaceName>ISP</InterfaceName>
</ToolOptions>
<ToolType>com.atmel.avrdbg.tool.stk500</ToolType>
<ToolNumber>
</ToolNumber>
<ToolName>STK500</ToolName>
</com_atmel_avrdbg_tool_stk500>
<avrtoolinterface>ISP</avrtoolinterface>
<avrtoolinterfaceclock>125000</avrtoolinterfaceclock>
<AsfFrameworkConfig>
<framework-data xmlns="">
<options />
<configurations />
<files />
<documentation help="" />
<offline-documentation help="" />
<dependencies>
<content-extension eid="atmel.asf" uuidref="Atmel.ASF" version="3.47.0" />
</dependencies>
</framework-data>
</AsfFrameworkConfig>
<com_atmel_avrdbg_tool_atmelice>
<ToolOptions>
<InterfaceProperties>
<IspClock>125000</IspClock>
</InterfaceProperties>
<InterfaceName>ISP</InterfaceName>
</ToolOptions>
<ToolType>com.atmel.avrdbg.tool.atmelice</ToolType>
<ToolNumber>J41800099437</ToolNumber>
<ToolName>Atmel-ICE</ToolName>
</com_atmel_avrdbg_tool_atmelice>
<custom>
<ToolOptions>
<InterfaceProperties>
<IspClock>125000</IspClock>
</InterfaceProperties>
<InterfaceName>
</InterfaceName>
</ToolOptions>
<ToolType>custom</ToolType>
<ToolNumber>
</ToolNumber>
<ToolName>Custom Programming Tool</ToolName>
</custom>
<com_atmel_avrdbg_tool_simulator>
<ToolOptions xmlns="">
<InterfaceProperties>
</InterfaceProperties>
<InterfaceName>
</InterfaceName>
</ToolOptions>
<ToolType xmlns="">com.atmel.avrdbg.tool.simulator</ToolType>
<ToolNumber xmlns="">
</ToolNumber>
<ToolName xmlns="">Simulator</ToolName>
</com_atmel_avrdbg_tool_simulator>
<AAFDebugger>
<AAFDebugFiles>
</AAFDebugFiles>
</AAFDebugger>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Release' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcc.compiler.symbols.DefSymbols>
<ListValues>
<Value>NDEBUG</Value>
</ListValues>
</avrgcc.compiler.symbols.DefSymbols>
<avrgcc.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcc.compiler.directories.IncludePaths>
<avrgcc.compiler.optimization.level>Optimize for size (-Os)</avrgcc.compiler.optimization.level>
<avrgcc.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcc.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcc.compiler.warnings.AllWarnings>True</avrgcc.compiler.warnings.AllWarnings>
<avrgcc.compiler.warnings.ExtraWarnings>True</avrgcc.compiler.warnings.ExtraWarnings>
<avrgcc.compiler.warnings.Pedantic>True</avrgcc.compiler.warnings.Pedantic>
<avrgcc.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -std=c11</avrgcc.compiler.miscellaneous.OtherFlags>
<avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>NDEBUG</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize for size (-Os)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.warnings.Pedantic>True</avrgcccpp.compiler.warnings.Pedantic>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -Wextra -std=c++20</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.general.NoStartupOrDefaultLibs>True</avrgcccpp.linker.general.NoStartupOrDefaultLibs>
<avrgcccpp.linker.libraries.Libraries>
<ListValues>
<Value>libm</Value>
</ListValues>
</avrgcccpp.linker.libraries.Libraries>
<avrgcccpp.linker.memorysettings.Flash>
<ListValues>
<Value>.text=0x3C00</Value>
</ListValues>
</avrgcccpp.linker.memorysettings.Flash>
<avrgcccpp.assembler.general.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.assembler.general.IncludePaths>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Debug' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcc.compiler.symbols.DefSymbols>
<ListValues>
<Value>DEBUG</Value>
</ListValues>
</avrgcc.compiler.symbols.DefSymbols>
<avrgcc.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcc.compiler.directories.IncludePaths>
<avrgcc.compiler.optimization.level>Optimize (-O1)</avrgcc.compiler.optimization.level>
<avrgcc.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcc.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcc.compiler.optimization.DebugLevel>Maximum (-g3)</avrgcc.compiler.optimization.DebugLevel>
<avrgcc.compiler.warnings.AllWarnings>True</avrgcc.compiler.warnings.AllWarnings>
<avrgcc.compiler.warnings.ExtraWarnings>True</avrgcc.compiler.warnings.ExtraWarnings>
<avrgcc.compiler.warnings.Pedantic>True</avrgcc.compiler.warnings.Pedantic>
<avrgcc.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -std=c11</avrgcc.compiler.miscellaneous.OtherFlags>
<avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>DEBUG</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize debugging experience (-Og)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcccpp.compiler.optimization.DebugLevel>Maximum (-g3)</avrgcccpp.compiler.optimization.DebugLevel>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.warnings.Pedantic>True</avrgcccpp.compiler.warnings.Pedantic>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -Wextra -std=c++20</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.general.NoStartupOrDefaultLibs>True</avrgcccpp.linker.general.NoStartupOrDefaultLibs>
<avrgcccpp.linker.libraries.Libraries>
<ListValues>
<Value>libm</Value>
</ListValues>
</avrgcccpp.linker.libraries.Libraries>
<avrgcccpp.linker.memorysettings.Flash>
<ListValues>
<Value>.text=0x3800</Value>
</ListValues>
</avrgcccpp.linker.memorysettings.Flash>
<avrgcccpp.assembler.general.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.assembler.general.IncludePaths>
<avrgcccpp.assembler.debugging.DebugLevel>Default (-Wa,-g)</avrgcccpp.assembler.debugging.DebugLevel>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<ItemGroup>
<Compile Include="clock.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="command.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="flash\flash.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="io\io.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="main.cpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="type\type.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\config.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\hardware.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\hardware0.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\hardware1.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\software.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\uart.hpp">
<SubType>compile</SubType>
</Compile>
</ItemGroup>
<ItemGroup>
<Folder Include="flash" />
<Folder Include="io" />
<Folder Include="uart" />
<Folder Include="type" />
</ItemGroup>
<Import Project="$(AVRSTUDIO_EXE_PATH)\\Vs\\Compiler.targets" />
</Project>

344
stk500v2/stk500v2.hpp
View File

@@ -1,344 +0,0 @@
#pragma once
#include <math.h>
#include <stddef.h>
#include <stdint.h>
namespace stk500v2 {
enum class Msg : uint8_t {
START = 0x1B, // ASCII ESC
TOKEN = 0x0E,
};
inline constexpr bool operator==(const Msg &msg, const uint8_t &num)
{
return static_cast<uint8_t>(msg) == num;
}
enum class Cmd : uint8_t {
SIGN_ON = 0x01,
SET_PARAMETER = 0x02,
GET_PARAMETER = 0x03,
SET_DEVICE_PARAMETERS = 0x04,
OSCCAL = 0x05,
LOAD_ADDRESS = 0x06,
FIRMWARE_UPGRADE = 0x07,
};
inline constexpr bool operator==(const Cmd &cmd, const uint8_t &num)
{
return static_cast<uint8_t>(cmd) == num;
}
enum class IspCmd : uint8_t {
ENTER_PROGMODE = 0x10,
LEAVE_PROGMODE = 0x11,
CHIP_ERASE = 0x12,
PROGRAM_FLASH = 0x13,
READ_FLASH = 0x14,
PROGRAM_EEPROM = 0x15,
READ_EEPROM = 0x16,
PROGRAM_FUSE = 0x17,
READ_FUSE = 0x18,
PROGRAM_LOCK = 0x19,
READ_LOCK = 0x1A,
READ_SIGNATURE = 0x1B,
READ_OSCCAL = 0x1C,
SPI_MULTI = 0x1D,
};
enum class PpCmd : uint8_t {
ENTER_PROGMODE = 0x20,
LEAVE_PROGMODE = 0x21,
CHIP_ERASE = 0x22,
PROGRAM_FLASH = 0x23,
READ_FLASH = 0x24,
PROGRAM_EEPROM = 0x25,
READ_EEPROM = 0x26,
PROGRAM_FUSE = 0x27,
READ_FUSE = 0x28,
PROGRAM_LOCK = 0x29,
READ_LOCK = 0x2A,
READ_SIGNATURE = 0x2B,
READ_OSCCAL = 0x2C,
SET_CONTROL_STACK = 0x2D,
};
enum class HvspCmd : uint8_t {
ENTER_PROGMODE = 0x30,
LEAVE_PROGMODE = 0x31,
CHIP_ERASE = 0x32,
PROGRAM_FLASH = 0x33,
READ_FLASH = 0x34,
PROGRAM_EEPROM = 0x35,
READ_EEPROM = 0x36,
PROGRAM_FUSE = 0x37,
READ_FUSE = 0x38,
PROGRAM_LOCK = 0x39,
READ_LOCK = 0x3A,
READ_SIGNATURE = 0x3B,
READ_OSCCAL = 0x3C,
};
enum class Status : uint8_t {
// Success
CMD_OK = 0x00,
// Warnings
CMD_TOUT = 0x80,
RDY_BSY_TOUT = 0x81,
SET_PARAM_MISSING = 0x82,
// Errors
CMD_FAILED = 0xC0,
CKSUM_ERROR = 0xC1,
CMD_UNKNOWN = 0xC9,
};
enum class Param : uint8_t {
BUILD_NUMBER_LOW = 0x80,
BUILD_NUMBER_HIGH = 0x81,
HW_VER = 0x90,
SW_MAJOR = 0x91,
SW_MINOR = 0x92,
VTARGET = 0x94,
VADJUST = 0x95,
OSC_PSCALE = 0x96,
OSC_CMATCH = 0x97,
SCK_DURATION = 0x98,
TOPCARD_DETECT = 0x9A,
STATUS = 0x9C,
DATA = 0x9D,
RESET_POLARITY = 0x9E,
CONTROLLER_INIT = 0x9F,
};
enum class Answer : uint8_t {
CKSUM_ERROR = 0xB0,
};
template <size_t Size>
struct Message {
uint8_t start;
uint8_t number;
uint16_t size;
uint8_t token;
uint8_t body[Size];
uint8_t checksum;
};
template <auto SignOnFn, auto SetParamFn, auto GetParamFn>
struct Callbacks {
static constexpr auto onSignOn = SignOnFn;
static constexpr auto onSetParam = SetParamFn;
static constexpr auto onGetParam = GetParamFn;
};
template <class Uart, uint16_t Timeout, auto CallbackFns>
class Stk500v2 {
public:
inline void init()
{
m_serial.init();
}
inline bool callback()
{
if (receiveMessage()) {
handleMessage();
}
if (m_timeout)
return true;
return false;
}
private:
static constexpr auto MSG_BUFFER_SIZE = 275;
using msg_t = Message<MSG_BUFFER_SIZE>;
msg_t m_msg;
Uart m_serial;
uint16_t m_timeout = Timeout;
inline bool receiveByte(uint8_t &data)
{
constexpr auto MICROSECOND = 1000.0 * 1000;
constexpr auto SYMBOL_SIZE = 9;
constexpr auto BYTE_DELAY_US = (SYMBOL_SIZE * MICROSECOND) / Uart::BAUD_RATE;
constexpr auto NUM_MS_DELAY_STEPS = static_cast<uint16_t>(round(1000 / BYTE_DELAY_US));
uint16_t msDelay = NUM_MS_DELAY_STEPS;
while (m_timeout) {
if (m_serial.rxByte(data)) {
m_timeout = Timeout;
return true;
}
_delay_us(BYTE_DELAY_US);
if (--msDelay == 0) {
msDelay = NUM_MS_DELAY_STEPS;
--m_timeout;
}
}
return false;
}
inline uint8_t calcChecksum() const
{
uint8_t checksum = static_cast<uint8_t>(m_msg.start);
for (uint16_t i = 1; i < 5 + m_msg.size; ++i) {
checksum ^= *(reinterpret_cast<const uint8_t *>(&m_msg) + i);
}
return checksum;
}
inline bool receiveMessage()
{
constexpr auto CHECK_MESSAGE_FORMAT = true;
constexpr auto CHECK_MESSAGE_SIZE = true;
constexpr auto CHECK_MESSAGE_CHECKSUM = true;
if (!receiveByte(m_msg.start)) {
return false;
}
if constexpr (CHECK_MESSAGE_FORMAT) {
if (m_msg.start != Msg::START)
return false;
}
if (!receiveByte(m_msg.number))
return false;
if (!receiveByte(*(reinterpret_cast<uint8_t *>(&m_msg.size) + 1)))
return false;
if (!receiveByte(*reinterpret_cast<uint8_t *>(&m_msg.size)))
return false;
if constexpr (CHECK_MESSAGE_SIZE) {
if (m_msg.size > sizeof(m_msg.body))
return false;
}
if (!receiveByte(m_msg.token))
return false;
if constexpr (CHECK_MESSAGE_FORMAT) {
if (m_msg.token != Msg::TOKEN)
return false;
}
for (uint16_t i = 0; i < m_msg.size; ++i) {
if (!receiveByte(m_msg.body[i]))
return false;
}
if (!receiveByte(m_msg.checksum))
return false;
if constexpr (CHECK_MESSAGE_CHECKSUM) {
if (m_msg.checksum != calcChecksum())
return false;
}
return true;
}
inline void transmitMessage() const
{
m_serial.txByte(m_msg.start);
m_serial.txByte(m_msg.number);
m_serial.txByte(m_msg.size >> 8);
m_serial.txByte(m_msg.size & 0xFF);
m_serial.txByte(m_msg.token);
for (uint16_t i = 0; i < m_msg.size; ++i)
m_serial.txByte(m_msg.body[i]);
m_serial.txByte(m_msg.checksum);
}
inline void handleMessage()
{
constexpr auto CHECK_MESSAGE_LENGTH = true;
switch (m_msg.body[0]) {
case static_cast<uint8_t>(Cmd::SIGN_ON): {
if constexpr (CHECK_MESSAGE_LENGTH) {
if (m_msg.size != 1)
break;
}
CallbackFns.onSignOn();
sendReply<static_cast<uint8_t>(Cmd::SIGN_ON)>();
break;
}
case static_cast<uint8_t>(Cmd::SET_PARAMETER): {
if constexpr (CHECK_MESSAGE_LENGTH) {
if (m_msg.size != 3)
break;
}
CallbackFns.onSetParam();
sendReply<static_cast<uint8_t>(Cmd::SET_PARAMETER)>();
break;
}
case static_cast<uint8_t>(Cmd::GET_PARAMETER): {
if constexpr (CHECK_MESSAGE_LENGTH) {
if (m_msg.size != 2)
break;
}
const auto errorOccurred = CallbackFns.onGetParam(static_cast<Param>(m_msg.body[1]), m_msg.body[2]);
sendReply<static_cast<uint8_t>(Cmd::GET_PARAMETER)>(errorOccurred);
break;
}
case static_cast<uint8_t>(Cmd::SET_DEVICE_PARAMETERS):
break;
case static_cast<uint8_t>(Cmd::OSCCAL):
break;
case static_cast<uint8_t>(Cmd::LOAD_ADDRESS):
break;
case static_cast<uint8_t>(Cmd::FIRMWARE_UPGRADE):
break;
}
}
template <uint8_t Command>
inline void sendReply(bool errorOccurred = false)
{
if constexpr (Command == Cmd::SIGN_ON) {
m_msg.size = 3 + 8;
m_msg.body[1] = static_cast<uint8_t>(Status::CMD_OK);
m_msg.body[2] = 8;
m_msg.body[3] = 'S';
m_msg.body[4] = 'T';
m_msg.body[5] = 'K';
m_msg.body[6] = '5';
m_msg.body[7] = '0';
m_msg.body[8] = '0';
m_msg.body[9] = '_';
m_msg.body[10] = '2';
} else if (Command == Cmd::SET_PARAMETER) {
m_msg.size = 2;
m_msg.body[1] = static_cast<uint8_t>(Status::CMD_OK);
} else if (Command == Cmd::GET_PARAMETER) {
if (!errorOccurred) {
m_msg.size = 3;
m_msg.body[1] = static_cast<uint8_t>(Status::CMD_OK);
} else {
m_msg.size = 2;
m_msg.body[1] = static_cast<uint8_t>(Status::CMD_FAILED);
}
}
m_msg.checksum = calcChecksum();
transmitMessage();
}
};
} // namespace stk500v2

1
stk500v2/type

Submodule stk500v2/type deleted from ce31ef017f

1
stk500v2/uart

Submodule stk500v2/uart deleted from dd37fa0411

76
test/check_pi.py Normal file
View File

@@ -0,0 +1,76 @@
#!/usr/bin/env python3
"""Position-independence lint: the property that lets the identical image run
from any slot, asserted from the built ELF and its object.
1. No absolute jmp/call — -mrelax normally guarantees it, but a branch that
grows out of relaxation range would break it silently.
2. Nothing flash-resident to address: the image is .text alone, so there is
no table whose runtime address has to be reconstructed.
3. The image is byte-identical when linked at a different base. This is
position independence itself rather than a proxy for it — an absolute
address anywhere in the image would move with the link and show up as a
differing byte.
Usage: check_pi.py <objdump> <objcopy> <cxx> <mcu> <elf> <object> <text_start_hex>
"""
import os
import re
import subprocess
import sys
import tempfile
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def main():
objdump, objcopy, cxx, mcu, elf, obj, text_start = sys.argv[1:]
text_start = int(text_start, 0)
listing = subprocess.run([objdump, "-d", elf], capture_output=True, text=True, check=True).stdout
absolute = [line for line in listing.splitlines() if re.search(r"\t(jmp|call)\t", line)]
if absolute:
fail("absolute control flow in the image:\n" + "\n".join(absolute))
# Allocated flash beyond .text would be data the running copy has to find.
# Only ALLOC sections reach the device at all; .comment and the debug
# sections ride along in the ELF container and are never flashed. objdump
# prints each section's flags on the line following its header.
headers = subprocess.run([objdump, "-h", elf], capture_output=True, text=True, check=True).stdout.splitlines()
for index, line in enumerate(headers):
fields = line.split()
if len(fields) < 6 or not fields[0].isdigit():
continue
name, size = fields[1], int(fields[2], 16)
flags = headers[index + 1] if index + 1 < len(headers) else ""
if "ALLOC" not in flags or not size:
continue
if name not in (".text", ".noinit", ".bss"):
fail(f"flash-resident section {name} ({size} bytes): the image must be .text alone")
# Relink at a different base and compare the bytes.
with tempfile.TemporaryDirectory() as work:
elsewhere = text_start - 0x200 if text_start >= 0x200 else text_start + 0x200
images = []
for base, tag in ((text_start, "here"), (elsewhere, "there")):
relinked = os.path.join(work, f"{tag}.elf")
binary = os.path.join(work, f"{tag}.bin")
subprocess.run(
[cxx, f"-mmcu={mcu}", "-nostartfiles", f"-Wl,--section-start=.text={base:#x}",
"-Wl,--defsym=pureboot_app=0", "-mrelax", obj, "-o", relinked],
check=True, capture_output=True)
subprocess.run([objcopy, "-O", "binary", relinked, binary], check=True)
images.append(open(binary, "rb").read())
if images[0] != images[1]:
differing = [i for i, (a, b) in enumerate(zip(*images)) if a != b]
fail(f"the image changes when linked at {elsewhere:#x} instead of {text_start:#x}: "
f"{len(differing)} byte(s) differ, first at offset {differing[0]:#x}")
print(f"PI lint: control flow PC-relative, .text only, identical linked at {text_start:#x} and {elsewhere:#x}")
if __name__ == "__main__":
main()

11
test/check_size.cmake Normal file
View File

@@ -0,0 +1,11 @@
execute_process(COMMAND ${SIZE_TOOL} ${ELF} OUTPUT_VARIABLE _out RESULT_VARIABLE _res)
if(NOT _res EQUAL 0)
message(FATAL_ERROR "avr-size failed")
endif()
# avr-size line 2 is "<text> <data> <bss> <dec> <hex> <file>".
string(REGEX MATCH "\n[ \t]*([0-9]+)" _m "${_out}")
set(_text ${CMAKE_MATCH_1})
if(_text GREATER LIMIT)
message(FATAL_ERROR ".text is ${_text} bytes, over the ${LIMIT}-byte boot section")
endif()
message(STATUS ".text ${_text} <= ${LIMIT} (boot section budget)")

36
test/check_unit.cmake Normal file
View File

@@ -0,0 +1,36 @@
# Asserts the autobaud loader's measured unit sits where the host will read
# it (--info's measured clock — the address is wire contract). Two homes: on
# a chip with the GPIOR pair the unit lives there and the image must carry no
# RAM word for it at all; elsewhere it is the first RAM object at SRAM start.
# Run as
# cmake -DOBJDUMP=... -DELF=... -DRAM_START=<data address> [-DGPIOR=<data address>]
# -P check_unit.cmake
execute_process(COMMAND ${OBJDUMP} -t ${ELF} OUTPUT_VARIABLE _syms RESULT_VARIABLE _res)
if(NOT _res EQUAL 0)
message(FATAL_ERROR "${OBJDUMP} -t ${ELF} failed")
endif()
# The symbol line: "00800100 l O .noinit 00000002 <mangled>unit_E".
string(REGEX MATCH "\n0*([0-9a-f]+)[^\n]+[ \t][^ \t\n]*unit_E\n" _line "${_syms}")
if(GPIOR)
if(_line)
message(FATAL_ERROR "unit_ RAM symbol present although the unit's home is GPIOR ${GPIOR} — "
"the host peeks the pair, and a RAM copy would be dead weight")
endif()
message(STATUS "no unit_ RAM object — the unit lives in the GPIOR pair at ${GPIOR}")
return()
endif()
if(NOT _line)
message(FATAL_ERROR "no unit_ symbol in ${ELF} — is this the autobaud loader?")
endif()
# AVR data-space symbols carry the 0x800000 VMA offset.
math(EXPR _want "0x800000 + ${RAM_START}" OUTPUT_FORMAT HEXADECIMAL)
math(EXPR _have "0x${CMAKE_MATCH_1}" OUTPUT_FORMAT HEXADECIMAL)
if(NOT _have STREQUAL _want)
message(FATAL_ERROR "unit_ sits at ${_have}, ram_start is ${_want} — the host peeks ram_start")
endif()
message(STATUS "unit_ at ${_have} == ram_start")

126
test/device.cpp Normal file
View File

@@ -0,0 +1,126 @@
// simavr "device" for the TSB bootloader: load the boot-linked ELF into the
// ATmega328P boot section, enter it (BOOTRST is not modelled, so we set PC to
// the boot base, exactly as simavr's own board_simduino does), and expose
// UART0 as a pty. A host client (Python pyserial, or the real tsbloader) then
// speaks the TSB protocol over that pty and actually flashes the device.
//
// SPM genuinely writes avr->flash on the mega cores, so on exit (or SIGTERM)
// we dump the flash image to a file for a ground-truth cross-check against
// what the client read back through the bootloader.
#include <csignal>
#include <cstdint>
#include <cstdio>
#include <cstdlib>
#include <cstring>
#include <print>
#include <unistd.h>
// The parts headers (uart_pty.h) carry no C++ linkage guards of their own,
// unlike simavr's core headers — the block covers both harmlessly.
extern "C" {
#include "avr_uart.h"
#include "sim_avr.h"
#include "sim_elf.h"
#include "uart_pty.h"
}
namespace {
avr_t *avr;
uart_pty_t uart_pty;
const char *dump_path;
[[noreturn]] void finish(int)
{
if (dump_path) {
std::FILE *f = std::fopen(dump_path, "wb");
if (f) {
std::fwrite(avr->flash, 1, avr->flashend + 1, f);
std::fclose(f);
}
}
uart_pty_stop(&uart_pty);
_exit(0);
}
} // namespace
int main(int argc, char *argv[])
{
if (argc < 3) {
std::println(stderr, "usage: {} <tsb.elf> <boot_base_hex> [flash_dump.bin]", argv[0]);
return 2;
}
auto boot_base = static_cast<std::uint32_t>(std::strtoul(argv[2], nullptr, 0));
dump_path = argc >= 4 ? argv[3] : nullptr;
avr = avr_make_mcu_by_name("atmega328p");
if (!avr) {
std::println(stderr, "device: no ATmega328P core");
return 1;
}
avr_init(avr);
avr->frequency = 16000000;
// Real flash powers up erased (0xff); the app region must look erased
// before the bootloader programs it.
std::memset(avr->flash, 0xff, avr->flashend + 1);
// simavr's ELF loader flattens the flash base to 0 (it expects an app at
// 0x0), but it hands back the boot code in fw.flash; place it at the boot
// section base ourselves and enter there (BOOTRST is not modelled).
elf_firmware_t fw{};
if (elf_read_firmware(argv[1], &fw) != 0) {
std::println(stderr, "device: cannot read {}", argv[1]);
return 1;
}
// An image that runs past flash end cannot execute on hardware, and a
// naive copy of it would smash the heap beyond avr->flash — after which
// the simulation misbehaves in ways that point everywhere but here.
// Refuse it loudly instead.
if (boot_base + fw.flashsize > avr->flashend + 1) {
std::println(stderr, "device: {} B at {:#x} runs past flash end {:#x} — image does not fit its slot",
fw.flashsize, boot_base, avr->flashend);
return 1;
}
std::memcpy(avr->flash + boot_base, fw.flash, fw.flashsize);
avr->pc = boot_base;
avr->codeend = avr->flashend;
// Optional: seed the config page (one page below the boot section) with a
// hex byte string, so the password gate and emergency erase can be tested.
// Layout: [appjump lo][appjump hi][timeout][password...][0xff].
const char *cfg = std::getenv("TSB_CONFIG");
if (cfg) {
std::uint32_t app_end = boot_base - 128; // config page sits directly below the boot code
for (int i = 0; cfg[i] && cfg[i + 1]; i += 2) {
char b[3] = {cfg[i], cfg[i + 1], 0};
avr->flash[app_end + i / 2] = static_cast<std::uint8_t>(std::strtoul(b, nullptr, 16));
}
}
// POLL_SLEEP makes simavr usleep(1) on every status-register read while the
// UART is idle — a host-CPU-saving hack that models no hardware and paces a
// tight-polling loader (one that releases TX between bytes, as one-wire does)
// in real time, distorting protocol timing. Clear it so the loader runs at
// true cycle speed.
std::uint32_t uflags = 0;
avr_ioctl(avr, AVR_IOCTL_UART_GET_FLAGS('0'), &uflags);
uflags &= ~AVR_UART_FLAG_POLL_SLEEP;
avr_ioctl(avr, AVR_IOCTL_UART_SET_FLAGS('0'), &uflags);
uart_pty_init(avr, &uart_pty);
uart_pty_connect(&uart_pty, '0');
std::println("TSB_PTY {}", uart_pty.pty.slavename);
std::fflush(stdout);
std::signal(SIGTERM, finish);
std::signal(SIGINT, finish);
for (;;) {
int state = avr_run(avr);
if (state == cpu_Done || state == cpu_Crashed)
break;
}
finish(0);
}

179
test/pbapp.cpp Normal file
View File

@@ -0,0 +1,179 @@
// Test-fixture application for the pureboot protocol tests: prints "APP" on
// the chip's serial link (the same link the loader uses) — the proof that
// the loader's hand-over, and on the tinies the host's reset-vector
// surgery, actually launched it. Linked normally (crt, vectors at 0); on
// the tinies its reset vector is the rjmp the host re-homes.
//
// On the hardware-USART link it then listens, and an 'L' makes it jump into
// the resident loader — the application-owned loader entry a
// BOOTRST-unprogrammed mega relies on (reset always boots the application
// there), exercised by the self-update tests. The software link idles:
// reset reaches those loaders through the patched vector (or the runner
// models BOOTRST), so the application owes them nothing.
//
// PUREBOOT_HANDOVER drops the listening and jumps straight in, leaving the
// USART enabled behind it — the hand-over state a loader bit-banging on that
// USART's own pins has to survive.
//
// The fixture speaks the deployment its loader was built for: the same
// PUREBOOT_* defines configure it, and without them it assumes the stock
// deployment (the crystal/RC clock table below, the chip's natural link).
#include <libavr/libavr.hpp>
using namespace avr::literals;
namespace {
consteval avr::hertz_t clock()
{
#if defined(PUREBOOT_CLOCK_HZ)
return avr::hertz_t{PUREBOOT_CLOCK_HZ};
#else
auto name = std::string_view{avr::hw::db.name};
if (name.starts_with("ATtiny13"))
return 9.6_MHz;
if (name.starts_with("ATtiny"))
return 8_MHz;
return 16_MHz;
#endif
}
#if !defined(PUREBOOT_TX)
#define PUREBOOT_TX pb1
#endif
#if !defined(PUREBOOT_RX)
#define PUREBOOT_RX pb0
#endif
#if !defined(PUREBOOT_USART)
#define PUREBOOT_USART 0
#endif
consteval bool use_hardware()
{
#if defined(PUREBOOT_SOFT_SERIAL)
return false;
#else
return avr::uart::has_usart<0>();
#endif
}
using dev = avr::device<{.clock = clock()}>;
template <avr::hertz_t C, bool Hardware = use_hardware()>
struct link {
#if defined(PUREBOOT_BAUD)
static constexpr avr::baud_t baud{PUREBOOT_BAUD};
#else
static constexpr avr::baud_t baud{115200};
#endif
using tx_t = avr::uart::usart<PUREBOOT_USART, C, {.baud = baud, .max_baud_error = 2.5_pct}>;
static void init()
{
avr::init<tx_t>();
}
static void tx(char c)
{
tx_t::write(static_cast<std::uint8_t>(c));
}
// The loader sits in the top slot — 512 bytes on every chip. The jump
// takes a word address, which is what makes the >64 KiB chips' entry
// reachable through a 16-bit pointer at all.
static void enter_loader()
{
constexpr std::uint32_t slot = 512;
reinterpret_cast<void (*)()>(static_cast<std::uint16_t>((avr::hw::db.mem.flash_size - slot) / 2))();
}
[[noreturn]] static void idle()
{
#if defined(PUREBOOT_HANDOVER)
// Hand back at once, with this USART still enabled — the state that
// leaves a bit-banged loader on its pins mute unless the loader
// releases it. Unconditional because there is no command wire to
// wait on: that loader's link is the pins, not this peripheral.
enter_loader();
__builtin_unreachable();
#else
for (;;) {
auto command = tx_t::read_blocking();
if (command == 'L')
enter_loader();
// 'D' leaves every word of the SPM page buffer dirty, so that a
// following 'L' enters the loader with the buffer it never clears.
if (command == 'D') {
for (std::uint16_t at = 0; at < avr::spm::page_bytes; at += 2)
avr::spm::fill(at, 0xdead);
tx('D');
}
}
#endif
}
};
template <avr::hertz_t C>
struct link<C, false> {
#if defined(PUREBOOT_BAUD)
static constexpr avr::baud_t baud{PUREBOOT_BAUD};
#else
static constexpr avr::baud_t baud{57600};
#endif
// A shared-pin deployment (RX == TX) banners as a guest on its own line:
// the pull-up input is the released line, the transmitter takes the pin
// for exactly one frame per byte — the shape a real one-wire application
// beside this loader uses.
static constexpr bool one_wire = avr::PUREBOOT_RX == avr::PUREBOOT_TX;
using tx_t = avr::uart::software_tx<C, avr::PUREBOOT_TX, baud, one_wire>;
static void init()
{
// The guest transmitter configures no pin; the released line — the
// pull-up input a receiver would own — is established here.
if constexpr (one_wire)
avr::init<avr::io::input<avr::PUREBOOT_TX, avr::io::pull::up>, tx_t>();
else
avr::init<tx_t>();
}
static void tx(char c)
{
tx_t::write(static_cast<std::uint8_t>(c));
}
[[noreturn]] static void idle()
{
#if defined(PUREBOOT_HEARTBEAT)
// Repeat the banner forever, which turns the fixture into a fixed
// cycles-per-bit transmitter: `tools/pbrig.py rate` sweeps the host rate
// against it to find the part's true bit rate, and from that the clock
// its RC oscillator is really running at. Only the *bit* timing carries
// the measurement — the delay merely spaces the lines out, so its own
// error does not matter. Software link only: the hardware-link idle owes
// the self-update tests a command loop, and a crystal deployment has
// nothing to measure.
while (true) {
tx('A');
tx('P');
tx('P');
tx('\r');
tx('\n');
dev::delay<50_ms>();
}
#else
while (true) {
}
#endif
}
};
} // namespace
int main()
{
link<dev::clock>::init();
#if !defined(PUREBOOT_HANDOVER)
link<dev::clock>::tx('A');
link<dev::clock>::tx('P');
link<dev::clock>::tx('P');
#endif
// The hand-over fixture stays silent: nothing is listening on the USART it
// brings up — the loader it hands to speaks those pins directly — so its
// banner would be a write into a peer that does not exist.
link<dev::clock>::idle();
}

211
test/pbautobaud.py Normal file
View File

@@ -0,0 +1,211 @@
#!/usr/bin/env python3
"""End-to-end autobaud test: drive an autobaud loader in simavr through the
calibration handshake and a flash + EEPROM + fuse round-trip, cross-checked
against the simulator's ground-truth memory — then repeat at a second F_CPU with
the *same* loader binary, which is the property autobaud exists for: one
clock-agnostic image that locks onto whatever rate the host sends.
Usage: pbautobaud.py <device_bin> <loader_elf> <mcu> <base_hex> <page>
<app_bin> <app_hz> <app_baud> <tool_py> <workdir> [link]
The loader is a software-serial build, driven over the GPIO⇄pty bridge; the
optional link overrides the default -l sw:B0,B1 — RX == TX in it is the
one-wire deployment, and every session then runs with the host's echo
discard on. The app fixture is built for (app_hz, app_baud); the hand-over
is checked at that point, and a second point at half the clock proves the
lock is measured, not baked in.
"""
import os
import re
import sys
import time
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def main():
args = sys.argv[1:]
link = args.pop() if len(args) == 11 else "sw:B0,B1"
(device_bin, elf, mcu, base_hex, page, app_bin, app_hz, app_baud, tool, workdir) = args
base, page, app_hz, app_baud = int(base_hex, 0), int(page), int(app_hz), int(app_baud)
one_wire = re.fullmatch(r"sw:([A-H][0-7]),\1(@[01])?", link) is not None
extra = ("--one-wire",) if one_wire else ()
sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
import pbsim
import pureboot as pb
os.makedirs(workdir, exist_ok=True)
ee_image = bytes(range(0xA0, 0xB0))
ee_path = os.path.join(workdir, "ee.bin")
open(ee_path, "wb").write(ee_image)
# The geometry the surgery planner needs, from the chip class the runner is
# told — the same derivation pbtest.py makes: the boot-sectioned megas need
# no vector surgery, the tinies and the boot-section-less m48s do, and the
# large chips speak word addresses.
mega = mcu.startswith("atmega")
patch = not mega or mcu.startswith("atmega48")
word_flash = base + pb.SLOT > 0x10000
wire_base = base // 2 if word_flash else base
flags = (1 if patch else 0) | (2 if word_flash else 0)
ground_truth = pb.Info(bytes([ord("P"), ord("B"), pb.NEWEST_LOADER, 0, 0, 0, page & 0xFF,
wire_base & 0xFF, wire_base >> 8, 0, 0, flags]))
def round_trip(hz, baud, label, hand_over):
"""One clock point: reset, calibrate + knock, program, verify against the
simulator's own flash, and (at the app's point) hand over to the fixture."""
dump = os.path.join(workdir, f"flash_{label}.bin")
device = pbsim.Device(device_bin, elf, mcu, str(hz), base_hex, page, baud, dump, link=link)
try:
# The host tool, in autobaud mode, sends the 0xC0 calibration pulse
# and a single knock at `baud`; the loader locks to it.
out = pbsim.run_tool(tool, device.pty, baud, *extra, "--autobaud", "--info", "--clock", str(hz),
"--fuses", "--flash", app_bin, "--eeprom", ee_path, "--stay")
for needed in ("version", "signature", "fuses", "verify:", "stays"):
if needed not in out:
fail(f"{label}: session output lacks {needed!r}\n{out}")
# The measured clock, decoded from the unit at whichever home this
# version keeps it in. The runner's clock is exact, so the figure
# must land inside the
# encoding's own envelope: the loader floors the bit period to
# 4-cycle spin granules after an 8-cycle discount, and the edge
# poll can shave a few cycles more — one granule of slack below
# the true clock, none above (in cycles per bit, times the rate).
measured = re.search(r"measured\s+(\d+) Hz", out)
if not measured:
fail(f"{label}: --info lacks the measured clock\n{out}")
measured = int(measured.group(1))
if not hz - 19 * baud <= measured <= hz + 4 * baud:
fail(f"{label}: measured clock {measured} Hz is {measured - hz:+d} off the true {hz}")
# Read both memories back over the locked link and check them.
read_flash = os.path.join(workdir, f"rf_{label}.bin")
read_eeprom = os.path.join(workdir, f"re_{label}.bin")
out = pbsim.run_tool(tool, device.pty, baud, *extra, "--autobaud", "--verify-flash", app_bin,
"--verify-eeprom", ee_path, "--read-flash", read_flash,
"--read-eeprom", read_eeprom, "--stay")
if out.count("verify:") != 2:
fail(f"{label}: did not verify both memories\n{out}")
if open(read_eeprom, "rb").read()[: len(ee_image)] != ee_image:
fail(f"{label}: EEPROM read-back mismatch")
if hand_over:
# Regression: a calibration pulse with no knock behind it must
# not wedge the loader. The knock's edge wait used to be
# unbudgeted, so one stray low pulse — EMI, or a host that opens
# the port and never knocks — held the loader forever and the
# application never ran. The whole activation is bounded now, so
# the window closes and the app boots; the banner is the proof.
# (The pause lets the loader reach its measurement loop, so the
# pulse is genuinely seen and the test cannot pass vacuously.)
device.reset()
port = pb.Port(device.pty, baud)
if one_wire:
port = pb.OneWirePort(port)
try:
time.sleep(0.2)
port.write(bytes((pb.CALIBRATE,)))
# Accumulate rather than match exactly: the reset leaves the
# idle line a framing artefact ahead of the banner, which is
# noise here — the question is only whether the app ran.
seen = b""
deadline = time.monotonic() + 180.0
while b"APP" not in seen and time.monotonic() < deadline:
seen += port.read_available(1.0)
if b"APP" not in seen:
fail(f"{label}: lone calibration pulse wedged the loader — app never bannered, saw {seen!r}")
print(f" {label}: lone calibration pulse does not wedge the loader")
finally:
port.close()
device.reset()
port = pb.Port(device.pty, baud)
if one_wire:
port = pb.OneWirePort(port)
try:
loader = pb.Loader(port)
live = loader.connect_autobaud(15)
if not pb.OLDEST_LOADER <= live.version <= pb.NEWEST_LOADER:
fail(f"{label}: loader reports pureboot {live.version}")
if loader.unified:
# pureboot 5's data space. 0x0200 is clear of the
# loader's own .noinit unit at the bottom of SRAM and of
# the stack at the top. Reading it back over the same
# locked link proves both directions of the new space.
probe = bytes(range(0x30, 0x40))
loader.write_ram(0x0200, probe)
if loader.read_ram(0x0200, len(probe)) != probe:
fail(f"{label}: RAM round-trip mismatch")
# The register file and the I/O space share the data
# address space on AVR, so the same command reaches a
# peripheral register. SPMCSR reads back as idle here.
verbose_ram = loader.read_ram(0x0200, 4)
print(f" {label}: RAM read/write ok ({verbose_ram.hex()})")
loader.run_application()
banner = port.read_exact(3, 5.0)
if banner != b"APP":
fail(f"{label}: application banner was {banner!r}")
finally:
port.close()
finally:
device.stop()
# Ground truth (read after the runner exits and writes its dump): what
# the tool programmed must be what the simulator actually holds.
pages = pb.plan_flash(open(app_bin, "rb").read(), ground_truth)
flash_true = open(dump, "rb").read()
for address, data in pages.items():
if flash_true[address : address + page] != data:
fail(f"{label}: simulator flash differs from the programmed image at {address:#06x}")
print(f" {label}: locked at {hz} Hz / {baud} Bd, flash+EEPROM verified"
+ (", hand-over ok" if hand_over else ""))
def must_lock(hz, baud, label):
"""The calibration alone, at a tight bit period. Nothing is programmed —
the question is only whether the loader can still measure the pulse."""
dump = os.path.join(workdir, f"flash_{label}.bin")
device = pbsim.Device(device_bin, elf, mcu, str(hz), base_hex, page, baud, dump,
link=link)
try:
port = pb.Port(device.pty, baud)
if one_wire:
port = pb.OneWirePort(port)
try:
live = pb.Loader(port).connect_autobaud(15)
if live.version != pb.NEWEST_LOADER:
fail(f"{label}: loader reports pureboot {live.version}")
finally:
port.close()
finally:
device.stop()
print(f" {label}: locked at {hz} Hz / {baud} Bd ({hz / baud:.0f} cycles a bit)")
# The app fixture is built for one clock; the hand-over banners there. A
# second point at double that clock, same loader binary, proves the lock is
# measured, not baked in — the whole point of autobaud. (Doubling keeps the
# bit period healthy; halving would drop it below the software UART's floor.)
round_trip(app_hz, app_baud, "clock-a", hand_over=True)
round_trip(app_hz * 2, app_baud, "clock-b", hand_over=False)
# Both points above sit near 100 cycles a bit, which is comfortable. The
# calibration's real floor is far tighter, and it is worth a gate: measured
# here, the lock is solid down to ~36 cycles a bit and fails outright by ~31
# — a sharp edge, not a fraying one. This pins the tightest standard rate the
# fixture's clock reaches, so a change that raises the floor is caught.
#
# It does *not* bound what a real deployment can use. On silicon the
# oscillator's own jitter costs roughly a factor of two: an ATtiny13A on its
# factory RC trim was reliable at ~118 cycles a bit and already locking only
# 1 attempt in 5 by ~59, which no exact-clock simulation can show. The
# deployable envelope is a README matter; this is the logic's floor.
must_lock(app_hz, app_baud * 2, "tight-bit")
print("pbautobaud: calibration lock and flash/EEPROM/fuse round-trip pass at both clocks, "
"and the tight bit period still locks")
if __name__ == "__main__":
main()

88
test/pbdirty.py Normal file
View File

@@ -0,0 +1,88 @@
#!/usr/bin/env python3
"""Dirty-page-buffer acceptance test: with no discard in the loader, a page
filled over words an earlier writer left takes those instead. The whole
contract is asserted — a bare verify sees the corruption, the repairing
verify fixes it in one rewrite, and it stays fixed.
The state is reached the one way the loader cannot prevent: an application
dirties the buffer and jumps in with no reset between. Boot-sectioned megas
forbid that outright (SPM runs only from the boot section, Atmel-8271 §26.2),
but simavr dispatches SPM from anywhere, which is what makes it constructible.
Usage: pbdirty.py <device_bin> <pureboot_elf> <mcu> <hz> <base_hex> <page>
<baud> <app_bin> <tool_py> <workdir>
"""
import os
import sys
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def main():
device_bin, elf, mcu, hz, base_hex, page, baud, app_bin, tool, workdir = sys.argv[1:]
page, baud = int(page), int(baud)
sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
import pbsim
import pureboot as pb
os.makedirs(workdir, exist_ok=True)
dump = os.path.join(workdir, "dump.bin")
# Reset boots the application on a BOOTRST-unprogrammed mega; its 'L' is
# the loader entry this test needs, reached without a reset.
device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump, reset_hex="0")
try:
port = pb.Port(device.pty, baud)
loader = pb.Loader(port)
loader.connect(25)
# Install the application and hand over to it.
pb.op_flash(loader, app_bin, erase=False, verify=True)
loader.run_application()
if port.read_exact(3, 5.0) != b"APP":
fail("the application did not start")
port.write(b"D")
if port.read_exact(1, 5.0) != b"D":
fail("the application did not acknowledge dirtying the page buffer")
port.write(b"L")
loader = pb.Loader(port)
loader.connect(25)
# Program by hand, so the corruption is observable before anything
# repairs it.
pages = pb.plan_flash(open(app_bin, "rb").read(), loader.info)
for address in sorted(pages):
loader.write_page(address, pages[address])
try:
pb.verify_pages(loader, pages)
except pb.Error as error:
if "verify failed" not in str(error):
fail(f"the read-back failed, but not at verify: {error}")
else:
# Either the fixture no longer dirties the buffer, or the loader
# clears it again — in which case this test's premise is gone.
fail("programming over a dirty page buffer came back clean")
# What the programming path uses: one rewrite settles it, and it stays
# settled.
pb.verify_pages(loader, pages, repair=True)
pb.verify_pages(loader, pages)
# Ground truth beyond the loader's own read-back.
loader.run_application()
if port.read_exact(3, 5.0) != b"APP":
fail("the application did not start after the recovered write")
port.close()
finally:
device.stop()
print("pbdirty: a dirty page buffer is caught by verify and cleared by the retry")
if __name__ == "__main__":
main()

79
test/pbmute.py Normal file
View File

@@ -0,0 +1,79 @@
#!/usr/bin/env python3
"""Hand-over with a USART left enabled on the loader's own pins.
A software or autobaud link deployed on a USART's TxD is mute if an
application hands over with that USART still enabled: TXEN keeps the USART
owning the pin, so the bit-banged transmitter's port writes go nowhere and the
loader receives and obeys while answering nothing. The link's init releases it.
The state is reached the way silicon reaches it — an application that sets up
its USART and jumps in with no reset between, so nothing clears UCSRnB for it.
The pin ownership itself is modelled by the device runner: simavr wires a
USART through IRQs alone and never takes the pin from the port, so without
that the mute could not happen here at all (test/pureboot_device.cpp).
Usage: pbmute.py <device_bin> <pureboot_elf> <mcu> <hz> <base_hex> <page>
<baud> <app_bin> <tool_py> <workdir> <link>
"""
import os
import re
import sys
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def main():
device_bin, elf, mcu, hz, base_hex, page, baud, app_bin, tool, workdir, link = sys.argv[1:]
page, baud = int(page), int(baud)
sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
import pbsim
import pureboot as pb
if "@" not in link:
fail(f"the link {link} names no owning USART — nothing would be under test")
# A shared line (RX == TX) echoes the host's own bytes; discard them the
# way the shipped --one-wire mode does.
one_wire = re.fullmatch(r"sw:([A-H][0-7]),\1@[01]", link) is not None
os.makedirs(workdir, exist_ok=True)
dump = os.path.join(workdir, "dump.bin")
device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump, link=link)
try:
port = pb.Port(device.pty, baud)
if one_wire:
port = pb.OneWirePort(port)
loader = pb.Loader(port)
loader.connect(25)
resident = loader.info.version
# Install the fixture and let it take over. It brings up the USART
# that owns these pins and jumps straight back in.
pb.op_flash(loader, app_bin, erase=False, verify=True)
loader.run_application()
# The loader is running again with that USART enabled behind it. Only
# the release makes it audible; without it the connect times out.
loader = pb.Loader(port)
try:
loader.connect(25)
except pb.Error as error:
fail(f"the loader never answered after the hand-over — the USART still owns its TX pin ({error})")
if loader.info.version != resident:
fail(f"identity changed across the hand-over: {resident} then {loader.info.version}")
# Answering is not enough: it has to still be a working loader.
pb.verify_pages(loader, pb.plan_flash(open(app_bin, "rb").read(), loader.info))
port.close()
finally:
device.stop()
print("pbmute: a loader on a USART's own pins answers after a hand-over that left it enabled")
if __name__ == "__main__":
main()

46
test/pbosccal.py Normal file
View File

@@ -0,0 +1,46 @@
#!/usr/bin/env python3
"""The build-time OSCCAL trim, observed through the wire: a loader built with
the OSCCAL axis holds the trim register at the built byte from its first
prompt on — the write sits at the top of run(), ahead of the WDRF bail, so
every path out of reset runs on the corrected clock. simavr's clock does not
follow OSCCAL, which is what makes the value assertable at all: the register
is plain state there, and the peek must return exactly what the build
declared rather than whatever the oscillator needed.
Usage: pbosccal.py <device_bin> <pureboot_elf> <mcu> <hz> <base_hex> <page>
<baud> <osccal_addr> <osccal_value> <tool_py> <workdir>
[link]
"""
import os
import sys
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def main():
args = sys.argv[1:]
link = args.pop() if len(args) == 12 else None
(device_bin, elf, mcu, hz, base_hex, page, baud, addr, value, tool, workdir) = args
addr, value, baud = int(addr, 0), int(value, 0), int(baud)
sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
import pbsim
os.makedirs(workdir, exist_ok=True)
dump = os.path.join(workdir, "flash_dump.bin")
device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump, link=link)
try:
out = pbsim.run_tool(tool, device.pty, baud, "--peek", f"{addr:#x}:1")
want = f"{addr:#06x} {value:02x}"
if want not in out:
fail(f"OSCCAL at {addr:#x} did not read back {value:#04x}:\n{out}")
finally:
device.stop()
print("OK")
if __name__ == "__main__":
main()

96
test/pbrehome.py Normal file
View File

@@ -0,0 +1,96 @@
#!/usr/bin/env python3
"""Re-homing acceptance test: an image programmed somewhere other than its
canonical slot must still be a working loader, and the ordinary
--update-loader flow must put a build into the top slot from there.
Two positions. Address 0, a raw .bin handed to a programmer: the staging
install and the word-0 redirect run from copies outside page 0's slot, so the
running-slot guard never blocks them. And the staging slot itself, where a
loader already sitting there IS the staging copy — recognized by its embedded
block and left in place, then streaming the new resident like any staged copy.
Usage: pbrehome.py <device_bin> <pureboot_elf> <update_bin> <mcu> <hz>
<base_hex> <page> <baud> <app_bin> <tool_py> <workdir>
"""
import os
import sys
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def rehome_from(pbsim, pb, device_bin, elf, place_hex, guard_probe, update_bin, base, page, baud, app_bin, workdir,
mcu, hz):
"""Place the loader at `place_hex`, heal through --update-loader, flash
the application, expect the banner."""
dump = os.path.join(workdir, f"dump-{place_hex}.bin")
state = os.path.join(workdir, f"rehome-{place_hex}.pbstate")
if os.path.exists(state):
os.unlink(state)
device = pbsim.Device(device_bin, elf, mcu, hz, place_hex, page, baud, dump, reset_hex="0")
try:
port = pb.Port(device.pty, baud)
loader = pb.Loader(port)
info = loader.connect(25)
if info.base != base:
fail(f"the misplaced copy reports base {info.base:#06x} — the info block must stay canonical")
# The accidental slot still guards itself; re-homing rides on the
# canonical slots being writable from it.
probe = int(guard_probe, 0)
before = loader.read_flash(probe, info.page)
loader.write_page(probe, bytes(info.page))
if loader.read_flash(probe, info.page) != before:
fail("the misplaced copy's guard let its own slot change")
# The ordinary update flow puts the build into the top slot.
pb.op_update_loader(loader, 25, update_bin, state, None)
update = open(update_bin, "rb").read()
if loader.read_flash(base, len(update)) != update:
fail("the canonical slot does not hold the update image")
# An application flashed through the healed resident overwrites the
# stale copy (surgery included) and launches.
pages = pb.plan_flash(open(app_bin, "rb").read(), loader.info)
for address in pb.covered(pages, loader.info, skip_blank=False):
loader.write_page(address, pages[address])
pb.verify_pages(loader, pages)
loader.run_application()
if port.read_exact(3, 5.0) != b"APP":
fail(f"application does not banner after the re-home from {place_hex}")
port.close()
finally:
device.stop()
def main():
(device_bin, elf, update_bin, mcu, hz, base_hex, page, baud, app_bin, tool, workdir) = sys.argv[1:]
base, page, baud = int(base_hex, 0), int(page), int(baud)
sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
import pbsim
import pureboot as pb
os.makedirs(workdir, exist_ok=True)
# Address 0: the raw-.bin-to-a-programmer accident. The guard probe is
# the copy's own page 0.
rehome_from(pbsim, pb, device_bin, elf, "0x0", "0x0", update_bin, base, page, baud, app_bin, workdir, mcu, hz)
print("re-home from address 0: converged")
# The staging slot: erased flash with the loader sitting exactly where
# a staging copy would — the tool must leave it in place and let it
# stream the (different) update build into the resident slot.
stage = base - pb.SLOT
rehome_from(pbsim, pb, device_bin, elf, hex(stage), hex(stage), update_bin, base, page, baud, app_bin, workdir,
mcu, hz)
print("re-home from the staging slot: converged")
print("pbrehome: a misplaced loader re-homes through the ordinary update flow")
if __name__ == "__main__":
main()

96
test/pbreloc.py Normal file
View File

@@ -0,0 +1,96 @@
#!/usr/bin/env python3
"""Position-independence acceptance test: the identical binary, flashed one
slot below the resident, must serve the complete command set from there. The
info block must come back byte-identical, the write guard must refuse the
staged copy's own slot and permit the resident's, and the staged copy must be
able to rewrite the resident verbatim.
Usage: pbreloc.py <device_bin> <pureboot_elf> <mcu> <hz> <base_hex> <page>
<baud> <tool_py> <workdir>
"""
import os
import subprocess
import sys
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def main():
device_bin, elf, mcu, hz, base_hex, page, baud, tool, workdir = sys.argv[1:]
base, page, baud = int(base_hex, 0), int(page), int(baud)
stage = None # derived from the device's own info (slot-sized) below
sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
import pbsim
import pureboot as pb
os.makedirs(workdir, exist_ok=True)
objcopy = os.environ.get("PB_OBJCOPY", "avr-objcopy")
image_path = os.path.join(workdir, "pureboot.bin")
subprocess.run([objcopy, "-O", "binary", elf, image_path], check=True)
image = open(image_path, "rb").read()
device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, os.path.join(workdir, "dump.bin"))
try:
port = pb.Port(device.pty, baud)
loader = pb.Loader(port)
info = loader.connect(25)
if info.base != base:
fail(f"info reports base {info.base:#06x}")
resident_info = info.raw
# Install the staging copy exactly as the update flow would.
stage = info.stage
staged = pb.staging_content(image, info)
pb.write_differing(loader, stage, staged)
# Enter it; from here on, every command runs in the relocated copy.
staged_info = loader.enter_copy(stage, 25)
if staged_info.raw != resident_info:
fail(f"staged info {staged_info.raw.hex()} != resident info {resident_info.hex()}")
# 'R' from the staged copy already proved itself in the install
# verify; 'F' must answer 4 bytes (values are unmodeled in simavr).
if len(loader.read_fuses()) != 4:
fail("fuse read from the staged copy")
# EEPROM round-trip through the staged copy.
pattern = bytes(range(0x50, 0x60))
loader.write_eeprom(0, pattern)
if loader.read_eeprom(0, len(pattern)) != pattern:
fail("EEPROM round-trip through the staged copy")
# The guard, both ways: its own slot refused (drained, unchanged), the
# resident slot writable. The refusal leaves its drained words in the
# SPM buffer, so the write that follows may take them — and clears
# them by writing, so the retry must not.
before = loader.read_flash(stage, page)
loader.write_page(stage, bytes(page))
if loader.read_flash(stage, page) != before:
fail("the staged copy's guard let its own slot change")
marker = bytes((i * 3) & 0xFF for i in range(page))
loader.write_page(base, marker)
if loader.read_flash(base, page) != marker:
loader.write_page(base, marker)
if loader.read_flash(base, page) != marker:
fail("the staged copy could not write the resident slot, even on retry")
# Restore the resident image through the staged copy, then 'J' back
# into it and prove it lives.
resident = image + b"\xff" * (pb.SLOT - len(image))
pb.write_differing(loader, base, resident)
back_info = loader.enter_copy(base, 25)
if back_info.raw != resident_info:
fail("the restored resident does not serve its info block")
port.close()
finally:
device.stop()
print("pbreloc: the relocated copy serves the full command set")
if __name__ == "__main__":
main()

71
test/pbsim.py Normal file
View File

@@ -0,0 +1,71 @@
"""Shared simavr harness for the pureboot tests: spawn the device runner,
hand out its pty, restart it from a flash dump (the power-fail path), and
keep its chatter out of undrained pipes."""
import os
import signal
import subprocess
class Device:
def __init__(self, binary, elf, mcu, hz, base_hex, page, baud, dump, reset_hex=None, resume=None, link=None,
window=False):
cmd = [binary]
if link:
cmd += ["-l", link]
if window:
cmd.append("-w") # report the first-transmit cycle, free-run idle
cmd += [elf, mcu, hz, base_hex, str(page), str(baud), dump]
if reset_hex is not None or resume is not None:
# Chips without a hardware boot section — the tinies and the
# m48s — reset to address 0 like silicon; the boot-sectioned
# megas re-vector to the loader base (BOOTRST).
patch = not mcu.startswith("atmega") or mcu.startswith("atmega48")
cmd.append(reset_hex if reset_hex is not None else ("0" if patch else base_hex))
if resume is not None:
cmd.append(resume)
self.log = open(dump + ".log", "a")
self.proc = subprocess.Popen(cmd, stdout=subprocess.PIPE, stderr=self.log, text=True)
self.dump = dump
self.pty = None
for _ in range(50):
line = self.proc.stdout.readline()
if not line:
break
if line.startswith("PB_PTY"):
self.pty = line.split()[1]
break
if not self.pty:
self.stop()
raise RuntimeError("device did not report a pty")
def reset(self):
"""The external reset line: SIGUSR1 re-enters at the reset vector."""
self.proc.send_signal(signal.SIGUSR1)
def power_fail(self):
"""SIGTERM: the runner dumps its flash and exits — the image a
restart resumes from."""
self.stop()
return self.dump
def stop(self):
self.proc.terminate()
try:
self.proc.wait(timeout=5)
except subprocess.TimeoutExpired:
self.proc.kill()
self.log.close()
def run_tool(tool, pty, baud, *args, timeout=180):
result = subprocess.run(
[os.environ.get("PYTHON", "python3"), tool, "--port", pty, "--baud", str(baud), "--wait", "25", *args],
capture_output=True,
text=True,
timeout=timeout,
)
print(result.stdout, end="")
if result.returncode != 0:
raise RuntimeError(f"tool exited {result.returncode}: {result.stderr.strip()}")
return result.stdout

187
test/pbtest.py Normal file
View File

@@ -0,0 +1,187 @@
#!/usr/bin/env python3
"""End-to-end protocol test: drive the simavr device with the real host tool
over its pty through flash, EEPROM, fuse and hand-over scenarios, and
cross-check the tool's view against the simulator's ground-truth dumps.
Usage: pbtest.py <device_bin> <pureboot_elf> <mcu> <hz> <base_hex> <page>
<baud> <eeprom_size> <app_bin> <tool_py> <workdir> [link]
The optional link is the runner's -l spec (usart1, sw:B5,B1, ...), for a
loader built off the chip's natural serial default.
"""
import os
import re
import sys
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def rjmp_decode(word, at, flash_words):
"""Where an rjmp word at word-address `at` lands — deliberately written
against the instruction-set definition (12-bit signed offset), not with
the host tool's encoder, so an encoding bug cannot verify itself."""
if word & 0xF000 != 0xC000:
fail(f"word at {at * 2:#06x} is {word:#06x}, not an rjmp")
offset = word & 0x0FFF
if offset >= 0x800:
offset -= 0x1000
return (at + 1 + offset) % flash_words
def main():
args = sys.argv[1:]
link = args.pop() if len(args) == 12 else None
(device_bin, elf, mcu, hz, base_hex, page, baud, eeprom_size, app_bin, tool, workdir) = args
base, page, baud, eeprom_size = int(base_hex, 0), int(page), int(baud), int(eeprom_size)
sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
import pbsim
import pureboot as pb
os.makedirs(workdir, exist_ok=True)
ee_image = bytes(range(0xA0, 0xB0))
ee_path = os.path.join(workdir, "ee.bin")
open(ee_path, "wb").write(ee_image)
dump = os.path.join(workdir, "flash_dump.bin")
read_flash = os.path.join(workdir, "readback_flash.bin")
read_eeprom = os.path.join(workdir, "readback_eeprom.bin")
# The geometry the host will discover, for computing the expected image:
# the boot-sectioned megas need no vector surgery (the tinies and the
# boot-section-less m48s do), the large chips speak word addresses, and
# the page byte is the wire's 0-means-256.
mega = mcu.startswith("atmega")
patch = not mega or mcu.startswith("atmega48")
# Where SRAM begins: the x8 and x4 megas push it past their extended I/O
# space, everything else starts right after the plain I/O registers. The
# loader keeps no statics and its stack sits at RAMEND, so the first SRAM
# byte is free for the data-space probe below.
classic = mcu in ("atmega8", "atmega8a", "atmega16", "atmega16a", "atmega32", "atmega32a")
ram_base = 0x0100 if mega and not classic else 0x0060
word_flash = base + pb.SLOT > 0x10000
wire_base = base // 2 if word_flash else base
flags = (1 if patch else 0) | (2 if word_flash else 0)
info = pb.Info(
bytes([ord("P"), ord("B"), pb.NEWEST_LOADER, 0, 0, 0, page & 0xFF])
+ bytes([wire_base & 0xFF, wire_base >> 8, eeprom_size & 0xFF, eeprom_size >> 8])
+ bytes([flags])
)
# A shared-line link (RX == TX in the -l spec) makes the host read every
# byte it sends back off the line; all sessions then discard the echo.
one_wire = bool(link) and re.fullmatch(r"sw:([A-H][0-7]),\1(@[01])?", link) is not None
extra = ("--one-wire",) if one_wire else ()
device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump, link=link)
try:
# Session 1: knock from reset, identify, program everything, stay.
out = pbsim.run_tool(tool, device.pty, baud, *extra, "--info", "--fuses", "--flash", app_bin,
"--eeprom", ee_path, "--stay")
for needed in ("version", "signature", "fuses", "verify:", "stays"):
if needed not in out:
fail(f"session 1 output lacks {needed!r}")
# Session 2: reconnect into the live session, verify, dump, exercise
# the data space; hand over is deferred — the pty must be reopened for
# the APP banner first.
probe = "c0ffee"
out = pbsim.run_tool(tool, device.pty, baud, *extra, "--verify-flash", app_bin, "--verify-eeprom", ee_path,
"--read-flash", read_flash, "--read-eeprom", read_eeprom,
"--poke", f"{ram_base:#x}:{probe}", "--peek", f"{ram_base:#x}:3", "--stay")
if out.count("verify:") != 2:
fail("session 2 did not verify both memories")
# What went into SRAM must come back out of it: the data space is one
# more selector on the same transfer as flash and EEPROM, so a wrong
# selector decode would show up here and nowhere else.
if probe not in out.replace(" ", ""):
fail(f"data-space round trip at {ram_base:#x} did not read back {probe}\n{out}")
eeprom_back = open(read_eeprom, "rb").read()
if eeprom_back[: len(ee_image)] != ee_image:
fail("EEPROM read-back mismatch")
# The expected post-surgery flash, straight from the tool's planner.
pages = pb.plan_flash(open(app_bin, "rb").read(), info)
flash_back = open(read_flash, "rb").read()
for address, data in pages.items():
if flash_back[address : address + page] != data:
fail(f"flash read-back mismatch in page {address:#06x}")
# An external reset re-enters through the patched word 0 (tinies; the
# runner resets them to address 0 like silicon) or BOOTRST (mega).
# The loader must answer a fresh knock, and the 'J' hand-over must
# land in the application, which banners on the same link.
device.reset()
port = pb.Port(device.pty, baud)
if one_wire:
port = pb.OneWirePort(port)
try:
loader = pb.Loader(port)
live = loader.connect(15)
# The loader built from this tree must report a version the tool
# beside it speaks — a bump the tool was never told about is a
# loader it would refuse to talk to. Not equality with the newest:
# the tool now spans two loader generations, the fixed-baud one
# here and the unified autobaud loader that follows it.
if not pb.OLDEST_LOADER <= live.version <= pb.NEWEST_LOADER:
fail(f"loader reports pureboot {live.version}, the tool speaks "
f"{pb.OLDEST_LOADER}..{pb.NEWEST_LOADER}")
# A W addressed inside a page rather than at its base must still
# consume exactly one page and prompt. The loader's own slot is the
# target — the guard refuses to commit it — and the payload is
# erased-state bytes, so the probe can disturb neither the image nor
# the page buffer it leaves behind. Hand-built rather than through
# write_page(), which would follow the fill with its erase and
# write; the point here is that the fill alone consumes exactly one
# page whatever the address's low bits say.
wire = base + 1
port.write(bytes((ord("W"), pb.selector(pb.SP_FLASH, wire), wire & 0xFF, (wire >> 8) & 0xFF))
+ b"\xff" * page)
if port.read_exact(1, 5.0) != pb.PROMPT:
fail("unaligned W did not return to the prompt")
loader.run_application()
banner = port.read_exact(3, 5.0)
if banner != b"APP":
fail(f"application banner was {banner!r}")
finally:
port.close()
finally:
device.stop()
# Ground truth: the simulator's own memories, against the host's view.
flash_true = open(dump, "rb").read()
if flash_true[:base] != flash_back:
fail("host flash read-back differs from the simulator's flash")
if flash_true[base] == 0xFF and flash_true[base + 1] == 0xFF:
fail("loader region looks erased in the ground-truth dump")
# The surgery, decoded independently: the patched vector must land on the
# loader, the trampoline on the application's own entry (patched-vector
# chips only — a boot-sectioned mega's word 0 stays the application's).
if patch:
flash_words = (base + pb.SLOT) // 2
app = open(app_bin, "rb").read()
word0 = flash_true[0] | (flash_true[1] << 8)
if rjmp_decode(word0, 0, flash_words) != base // 2:
fail("patched reset vector does not land on the loader base")
trampoline = flash_true[base - 2] | (flash_true[base - 1] << 8)
original = app[0] | (app[1] << 8)
if rjmp_decode(trampoline, (base - 2) // 2, flash_words) != rjmp_decode(original, 0, flash_words):
fail("trampoline does not land on the application's own entry")
ee_true_path = dump + ".eeprom"
if os.path.exists(ee_true_path):
ee_true = open(ee_true_path, "rb").read()
if ee_true[: len(ee_image)] != ee_image:
fail("ground-truth EEPROM does not match what was programmed")
print("pbtest: all scenarios pass")
if __name__ == "__main__":
main()

222
test/pbupdate.py Normal file
View File

@@ -0,0 +1,222 @@
#!/usr/bin/env python3
"""Self-update end-to-end: an application is flashed, the loader replaces
itself with a re-timed build, and every power-fail phase is rehearsed by
killing the device mid-write, restarting it from its flash dump, and letting
a re-run complete the update.
The boot-sectioned megas run the BOOTRST-unprogrammed profile — reset boots
the application, whose 'L' is the application-owned loader entry — with
--assume-fuses standing in for the fuse read simavr cannot model.
Usage: pbupdate.py <device_bin> <pureboot_elf> <update_elf> <mcu> <hz>
<base_hex> <page> <baud> <app_bin> <tool_py> <workdir>
"""
import os
import subprocess
import sys
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def rjmp_decode(word, at, flash_words):
"""Written against the instruction-set definition, not with the tool's
encoder, so an encoding bug cannot verify itself."""
if word & 0xF000 != 0xC000:
fail(f"word at {at * 2:#06x} is {word:#06x}, not an rjmp")
offset = word & 0x0FFF
if offset >= 0x800:
offset -= 0x1000
return (at + 1 + offset) % flash_words
class PowerFail(Exception):
pass
def assumed_fuses(pb, image):
"""Synthetic 'F' bytes for --assume-fuses: the smallest boot section
covering both the resident and the staging slot (two slots — what a
self-update needs), BOOTRST unprogrammed — the per-chip BOOTSZ ladder
and fuse byte come from the tool's own table, keyed by the update
image's embedded signature."""
info = pb.image_info(image)
which, ladder = pb.BOOT_FUSE[bytes(info.signature[1:3])]
bits = min((b for b in ladder if ladder[b] * 2 >= 2 * pb.SLOT), key=lambda b: ladder[b])
fuses = bytearray((0xFF, 0xFF, 0xFF, 0xFF))
fuses[which] = 0xF8 | (bits << 1) | 1
return bytes(fuses)
def make_fault_loader(pb, base, slot, kill_region, kill_hits, device):
"""A Loader whose write_page kills the device (or, with device=None,
just the host) at the Nth write into a region; the sequence
stage->resident->stage distinguishes the install from the restore."""
class FaultLoader(pb.Loader):
def __init__(self, port):
super().__init__(port)
self.seen_resident = False
self.hits = 0
def write_page(self, address, data):
if address >= base:
phase = "resident"
self.seen_resident = True
elif address >= base - slot:
phase = "stage_restore" if self.seen_resident else "stage"
else:
phase = "app"
if phase == kill_region:
self.hits += 1
if self.hits == kill_hits:
if device is not None:
device.power_fail()
raise PowerFail(f"{kill_region} write {kill_hits}")
super().write_page(address, data)
return FaultLoader
def main():
(device_bin, elf, update_elf, mcu, hz, base_hex, page, baud, app_bin, tool, workdir) = sys.argv[1:]
base, page, baud = int(base_hex, 0), int(page), int(baud)
mega = mcu.startswith("atmega")
# The m48s are megas without a boot section: patched vector, no fuse
# preflight, and the same reset-to-0 the tinies get.
patch = not mega or mcu.startswith("atmega48")
reset_hex = "0" if mega else None # the boot-sectioned mega runs BOOTRST-unprogrammed here
sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
import pbsim
import pureboot as pb
slot = pb.SLOT
os.makedirs(workdir, exist_ok=True)
objcopy = os.environ.get("PB_OBJCOPY", "avr-objcopy")
images = {}
for name, source in (("v0", elf), ("v9", update_elf)):
path = os.path.join(workdir, name + ".bin")
subprocess.run([objcopy, "-O", "binary", source, path], check=True)
images[name] = open(path, "rb").read()
if images["v0"] == images["v9"]:
fail("the update image is byte-identical to the resident build")
dump = os.path.join(workdir, "dump.bin")
state = os.path.join(workdir, "update.pbstate")
fuses = assumed_fuses(pb, images["v0"]) if mega and not patch else None
def connect(device):
port = pb.Port(device.pty, baud)
if mega:
# Reset boots the application here; its 'L' is the loader entry.
# To a live loader the same byte is an ignored command.
port.read_available(0.5)
port.write(b"L")
loader = pb.Loader(port)
loader.connect(25)
return port, loader
def padded(image):
return image + b"\xff" * (slot - len(image))
def resident_bytes(loader):
return loader.read_flash(base, slot)
def assert_state(loader, image, app_pages):
if resident_bytes(loader) != padded(image):
fail("resident loader does not match the update image")
stage = base - slot
got = loader.read_flash(stage, slot)
for address, data in app_pages.items():
if stage <= address < base:
if got[address - stage : address - stage + page] != data:
fail(f"staging region page {address:#06x} not restored")
device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump, reset_hex=reset_hex)
final = "v0"
try:
# The application first — its planner output is the restore truth.
pbsim.run_tool(tool, device.pty, baud, "--flash", app_bin, "--stay")
port, loader = connect(device)
app_pages = pb.plan_flash(open(app_bin, "rb").read(), loader.info)
port.close()
# A clean CLI update, resident -> v9.
args = ["--update-loader", os.path.join(workdir, "v9.bin"), "--state", state, "--stay"]
if fuses:
args += ["--assume-fuses", fuses.hex()]
out = pbsim.run_tool(tool, device.pty, baud, *args)
if "loader updated" not in out:
fail("update did not report success")
if os.path.exists(state):
fail("state file survived a completed update")
port, loader = connect(device)
assert_state(loader, images["v9"], app_pages)
loader.run_application()
if port.read_exact(3, 5.0) != b"APP":
fail("application does not banner after the update")
port.close()
final = "v9"
print("clean update: resident replaced, staging restored, application intact")
# Power-fail rehearsal: kill mid-phase, restart from the dump,
# re-run, and the update must still complete. Each round flips the
# direction so the flash is never already at its target. The mega's
# mid-resident-rewrite loss is exercised as a host crash instead:
# with BOOTRST unprogrammed and the resident mid-erase, a power loss
# there has no reset path into the staging copy — the documented
# cost of that profile (README).
for kill_region, kill_hits, kill_device in (
("stage", 2, True),
("resident", 1, patch),
("stage_restore", 2, True),
):
device.reset() # the previous round left the application running
port, loader = connect(device)
target = "v9" if resident_bytes(loader) == padded(images["v0"]) else "v0"
image_path = os.path.join(workdir, target + ".bin")
injected = make_fault_loader(pb, base, slot, kill_region, kill_hits, device if kill_device else None)(port)
injected.info = loader.info
try:
pb.op_update_loader(injected, 25, image_path, state, fuses)
fail(f"{kill_region}: fault never triggered")
except PowerFail as event:
print(f"power fail injected: {event}")
port.close()
if kill_device:
device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump,
reset_hex=reset_hex, resume=dump)
port, loader = connect(device)
pb.op_update_loader(loader, 25, image_path, state, fuses)
assert_state(loader, images[target], app_pages)
loader.run_application()
if port.read_exact(3, 5.0) != b"APP":
fail(f"{kill_region}: application lost after the resumed update")
port.close()
final = target
print(f"resumed after {kill_region} loss: update completed, application intact")
finally:
device.stop()
# Ground truth: the simulator's own flash against the final state, and
# on the patched-vector chips an independent decode of the reset routing.
flash = open(dump, "rb").read()
if flash[base : base + slot] != padded(images[final]):
fail("ground-truth resident region does not match the final image")
if patch:
flash_words = (base + slot) // 2
word0 = flash[0] | (flash[1] << 8)
if rjmp_decode(word0, 0, flash_words) != base // 2:
fail("ground-truth reset vector does not land on the loader")
app = open(app_bin, "rb").read()
trampoline = flash[base - 2] | (flash[base - 1] << 8)
if rjmp_decode(trampoline, (base - 2) // 2, flash_words) != rjmp_decode(app[0] | (app[1] << 8), 0, flash_words):
fail("ground-truth trampoline does not land on the application entry")
print("pbupdate: clean update + all power-fail phases recovered")
if __name__ == "__main__":
main()

137
test/pbwindow.py Normal file
View File

@@ -0,0 +1,137 @@
#!/usr/bin/env python3
"""The activation window as a behavioral duration gate.
The loader's window is a counted poll loop whose per-poll cost is hand-counted
in the source (`link::poll_cycles`) — but the loop compiles in consumer
context, so only the running image can prove the count. This test installs a
real application beside the loader (the host tool's own `plan_flash` supplies
the reset-vector surgery), starts the simulator with the line idle, and reads
the cycle of the first transmit activity: nothing talks until the window
closes and the application banners, so that cycle *is* the window, give or
take a banner lead measured in microseconds. Asserted at ±2 % — one
mis-counted cycle per poll shifts a window by 10 % and more.
Fixed-baud loaders declare their window in seconds (--seconds, the build's
TIMEOUT). The autobaud loader's window is its calibration poll budget
(--autobaud-polls); the seconds it amounts to are budget × 9 / f_cpu, the
measured cost of the calibrate() wait loop this gate pins.
"""
import argparse
import importlib.util
import pathlib
import select
import sys
import time
sys.path.insert(0, str(pathlib.Path(__file__).resolve().parent))
from pbsim import Device
# The calibrate() budget loop's cycles per poll in the built image — what the
# README's window arithmetic rests on, verified here. A measured fact, not a
# design constant: the wait's exit branches land where the compiler's block
# layout puts them, and the bounded-calibration rework moved the loop from
# ten cycles to nine.
AUTOBAUD_POLL_CYCLES = 9
def load_tool(path):
spec = importlib.util.spec_from_file_location("pureboot", path)
module = importlib.util.module_from_spec(spec)
spec.loader.exec_module(module)
return module
def compose_flash(pb, loader_bytes, app_bytes, mcu, base, page):
"""The flash image a completed programming session leaves: application
(with the tinies' vector surgery), loader at base — built through the
host tool's own planner so the surgery is the shipped one, not a copy."""
flash_size = base + pb.SLOT
patch = not mcu.startswith("atmega") or mcu.startswith("atmega48")
word_flash = flash_size > 0x10000
wire_base = base // 2 if word_flash else base
flags = (1 if patch else 0) | (2 if word_flash else 0)
raw = bytes((ord("P"), ord("B"), 5, 0, 0, 0, page & 0xFF,
wire_base & 0xFF, wire_base >> 8, 0, 0, flags))
info = pb.Info(raw)
flash = bytearray(b"\xff" * flash_size)
for address, content in pb.plan_flash(app_bytes, info).items():
flash[address:address + len(content)] = content
flash[base:base + len(loader_bytes)] = loader_bytes
return bytes(flash)
def first_tx_cycle(device, deadline):
"""The PB_WINDOW_TX report, or None. The runner prints it once."""
stream = device.proc.stdout
while True:
remaining = deadline - time.monotonic()
if remaining <= 0:
return None
ready, _, _ = select.select([stream], [], [], remaining)
if not ready:
return None
line = stream.readline()
if not line:
return None
if line.startswith("PB_WINDOW_TX"):
return int(line.split()[1])
def main():
parser = argparse.ArgumentParser()
parser.add_argument("--device", required=True)
parser.add_argument("--loader", required=True)
parser.add_argument("--mcu", required=True)
parser.add_argument("--hz", type=int, required=True)
parser.add_argument("--base", required=True)
parser.add_argument("--page", type=int, required=True)
parser.add_argument("--baud", type=int, required=True)
parser.add_argument("--app", required=True)
parser.add_argument("--tool", required=True)
parser.add_argument("--workdir", required=True)
parser.add_argument("--link", default=None)
parser.add_argument("--seconds", type=float, default=None)
parser.add_argument("--autobaud-polls", type=int, default=None)
args = parser.parse_args()
if (args.seconds is None) == (args.autobaud_polls is None):
parser.error("exactly one of --seconds / --autobaud-polls")
pb = load_tool(args.tool)
base = int(args.base, 0)
expected = (args.seconds if args.seconds is not None
else args.autobaud_polls * AUTOBAUD_POLL_CYCLES / args.hz)
work = pathlib.Path(args.workdir)
work.mkdir(parents=True, exist_ok=True)
# Every loader target objcopies its slot content beside the ELF (.bin).
loader_bytes = pathlib.Path(args.loader + ".bin").read_bytes()
app_bytes = pathlib.Path(args.app).read_bytes()
flash_file = work / "window-flash.bin"
flash_file.write_bytes(compose_flash(pb, loader_bytes, app_bytes, args.mcu, base, args.page))
device = Device(args.device, args.loader, args.mcu, str(args.hz), args.base, args.page,
args.baud, str(work / "window-dump.bin"), resume=str(flash_file),
link=args.link, window=True)
try:
# Simulation speed is machine-dependent; a few hundred thousand
# cycles per wall second is the pessimistic floor.
budget = max(60.0, expected * args.hz / 300000)
cycle = first_tx_cycle(device, time.monotonic() + budget)
finally:
device.stop()
if cycle is None:
print(f" [FAIL] no transmit activity within {budget:.0f} s wall "
f"(expected a {expected:.2f} s window)")
return 1
measured = cycle / args.hz
error = (measured - expected) / expected
ok = abs(error) <= 0.02
print(f" [{'PASS' if ok else 'FAIL'}] window {measured:.3f} s vs declared "
f"{expected:.3f} s ({error:+.1%}, gate ±2%)")
return 0 if ok else 1
if __name__ == "__main__":
raise SystemExit(main())

668
test/pureboot_device.cpp Normal file
View File

@@ -0,0 +1,668 @@
// simavr "device" for the pureboot protocol tests, every chip. Loads the
// boot-linked ELF at the loader base, starts execution there (BOOTRST / the
// patched vector are not what is under test), and exposes the loader's
// serial link as a pty for the real host tool:
//
// - Hardware USART builds: simavr's uart_pty on the selected instance.
// - Software UART builds: an 8N1 bridge between a pty and the GPIO pins,
// timed against the simulated cycle counter (drives the loader's RX,
// decodes its TX).
//
// The link follows the chip's natural default (USART0 on the megas, the
// software UART on PB0/PB1 elsewhere) unless -l overrides it: `-l usart1`
// for the second instance, `-l sw:B5,B1` for a software build's RX,TX pins,
// and `-l sw:D0,D1@0` where those pins are a USART's own — see the pin
// ownership the bridge models below.
//
// simavr's tiny cores decode the SPM opcode but attach no NVM module — SPM
// is a silent no-op (the mega's boot section has one, avr_flash). The
// missing module is supplied here: the SPM ioctl reads SPMCSR/Z/r1:r0 and
// implements buffer fill, page erase, page write, and CTPB, completing
// instantly. RFLB's LPM diversion (fuse readout) stays unmodeled, so the
// 'F' command answers with flash bytes — the tests assert transport only.
//
// On exit (or SIGTERM) the flash and EEPROM are dumped to files for a
// ground-truth cross-check against what the host read back.
#include <csignal>
#include <cstdint>
#include <cstdio>
#include <cstdlib>
#include <cstring>
#include <print>
#include <string_view>
#include <fcntl.h>
#include <pty.h>
#include <termios.h>
#include <unistd.h>
// The parts headers (uart_pty.h) carry no C++ linkage guards of their own,
// unlike simavr's core headers — the block covers both harmlessly.
extern "C" {
#include "avr_eeprom.h"
#include "avr_flash.h"
#include "avr_ioport.h"
#include "avr_uart.h"
#include "sim_avr.h"
#include "sim_elf.h"
#include "sim_io.h"
#include "uart_pty.h"
}
namespace {
avr_t *avr;
uart_pty_t uart_pty;
bool link_software;
avr_uart_t *hw_uart; // the pty-driven USART, for the datasheet-reset fix below
char uart_digit = '0';
char sw_rx_port = 'B', sw_tx_port = 'B';
int sw_rx_bit = 0, sw_tx_bit = 1;
char sw_tx_owner = 0; // the USART whose TXD the software link sits on
const char *dump_path;
std::uint32_t reset_pc;
volatile std::sig_atomic_t reset_requested;
// -w: report the cycle of the first transmit activity, once. What the
// activation-window gate reads — with an idle line and an application
// installed, the first thing that ever talks is the application's banner,
// so this cycle *is* the loader's window plus a banner lead measured in
// microseconds. Idle pacing is skipped in this mode: there is no real-time
// host in the loop, and a paced multi-second window would take hours.
bool window_report;
bool window_tx_seen;
void window_first_tx()
{
if (!window_report || window_tx_seen)
return;
window_tx_seen = true;
std::println("PB_WINDOW_TX {}", avr->cycle);
std::fflush(stdout);
}
void window_uart_hook(avr_irq_t *, std::uint32_t, void *)
{
window_first_tx();
}
// One-wire (RX == TX in the link spec): both directions on one GPIO line
// idling on the firmware's pull-up. The bridge then follows the pin's
// direction the way the real wiring does: it drives only while the
// firmware's DDR bit reads input, decodes transitions as the firmware's
// transmit only while the firmware owns the line, ignores its own raises
// coming back through the shared irq — and echoes every byte it drives back
// to the pty, which is what the host-side FTDI tie does and what the host
// tool's --one-wire mode reads back and discards.
bool link_one_wire;
bool mcu_owns_line;
bool self_drive;
int parse_link(std::string_view spec)
{
if (spec == "usart0" || spec == "usart1") {
link_software = false;
uart_digit = spec[5];
return 0;
}
if (spec.starts_with("sw")) {
link_software = true;
if (spec.size() == 2)
return 0;
char owner = 0;
int fields =
std::sscanf(spec.data() + 2, ":%c%d,%c%d@%c", &sw_rx_port, &sw_rx_bit, &sw_tx_port, &sw_tx_bit, &owner);
if (fields == 4 || fields == 5) {
sw_tx_owner = owner;
link_one_wire = sw_rx_port == sw_tx_port && sw_rx_bit == sw_tx_bit;
return 0;
}
}
return -1;
}
// simavr 1.6's avr_flash PGERS handler erases spm_pagesize bytes starting at
// Z & ~1 instead of the page containing Z (its PGWRT path masks correctly) —
// hardware ignores the in-page bits (§26.8.1), so an erase issued with Z
// anywhere inside the page wipes half the neighbouring page in simulation
// only. Wrap the mega's registered flash ioctl and re-dispatch page erases
// with Z forced to the page boundary; everything else passes through.
//
// A second gap on the boot-section-less m48s: their RWWSRE bit is the
// temporary-buffer discard (Atmel-8271 §26.2/§26.3.1), but the stock model
// gates its RWWSRE branch on AVR_SELFPROG_HAVE_RWW — absent on the m48
// core — so the discard store falls through into the buffer-fill branch and
// plants whatever Z/R1:R0 happen to hold. Perform the silicon's discard
// here instead.
avr_flash_t *mega_flash;
int (*mega_flash_ioctl)(avr_io_t *io, std::uint32_t ctl, void *param);
int fixed_flash_ioctl(avr_io_t *io, std::uint32_t ctl, void *param)
{
if (ctl == AVR_IOCTL_FLASH_SPM && avr_regbit_get(io->avr, mega_flash->pgers)) {
auto z = static_cast<std::uint16_t>(io->avr->data[30] | (io->avr->data[31] << 8));
auto masked = static_cast<std::uint16_t>(z & ~(mega_flash->spm_pagesize - 1));
io->avr->data[30] = static_cast<std::uint8_t>(masked);
io->avr->data[31] = static_cast<std::uint8_t>(masked >> 8);
int result = mega_flash_ioctl(io, ctl, param);
io->avr->data[30] = static_cast<std::uint8_t>(z);
io->avr->data[31] = static_cast<std::uint8_t>(z >> 8);
return result;
}
if (ctl == AVR_IOCTL_FLASH_SPM && !(mega_flash->flags & AVR_SELFPROG_HAVE_RWW) &&
(io->avr->data[mega_flash->r_spm] & 0x11) == 0x11) { // RWWSRE|SELFPRGEN: the m48 buffer discard
for (int i = 0; i < mega_flash->spm_pagesize / 2; i++) {
mega_flash->tmppage[i] = 0xffff;
mega_flash->tmppage_used[i] = 0;
}
avr_regbit_clear(io->avr, mega_flash->selfprgen);
return 0;
}
return mega_flash_ioctl(io, ctl, param);
}
void fix_mega_flash_erase()
{
for (avr_io_t *io = avr->io_port; io; io = io->next) {
if (io->kind && std::string_view{io->kind} == "flash") {
mega_flash = reinterpret_cast<avr_flash_t *>(io);
mega_flash_ioctl = io->ioctl;
io->ioctl = fixed_flash_ioctl;
return;
}
}
std::println(stderr, "device: no flash module to fix — SPM page erases may misalign");
}
void request_reset(int)
{
reset_requested = 1;
}
// ------------------------------------------------------------- tiny NVM ---
struct tiny_nvm_t {
avr_io_t io;
std::uint8_t buffer[128];
std::uint8_t used[128]; // a buffer word loads once until erased — like silicon
unsigned page;
};
tiny_nvm_t nvm;
int nvm_ioctl(avr_io_t *io, std::uint32_t ctl, void *)
{
if (ctl != AVR_IOCTL_FLASH_SPM)
return -1;
auto *n = reinterpret_cast<tiny_nvm_t *>(io);
avr_t *mcu = io->avr;
std::uint8_t command = mcu->data[0x57] & 0x1f; // SPMCSR, both tinies
auto z = static_cast<std::uint16_t>(mcu->data[30] | (mcu->data[31] << 8));
std::uint32_t page_base = static_cast<std::uint32_t>(z & ~(n->page - 1)) % (mcu->flashend + 1);
if (command == 0x01) { // SPMEN alone: buffer fill from r1:r0
unsigned offset = z & (n->page - 1) & ~1u;
if (!n->used[offset]) { // first write wins until the buffer clears
n->buffer[offset] = mcu->data[0];
n->buffer[offset + 1] = mcu->data[1];
n->used[offset] = 1;
}
} else if (command == 0x03) { // PGERS
std::memset(mcu->flash + page_base, 0xff, n->page);
} else if (command == 0x05) { // PGWRT: programming only clears bits
for (unsigned i = 0; i < n->page; i++)
mcu->flash[page_base + i] &= n->buffer[i];
std::memset(n->buffer, 0xff, n->page);
std::memset(n->used, 0, n->page);
} else if (command == 0x11) { // CTPB
std::memset(n->buffer, 0xff, n->page);
std::memset(n->used, 0, n->page);
}
mcu->data[0x57] &= static_cast<std::uint8_t>(~0x1f); // the operation completes instantly
return 0;
}
// ----------------------------------------------------------- GPIO bridge ---
int pty_master = -1;
avr_irq_t *rx_pin; // the loader's RX (PB0), driven from the pty
avr_cycle_count_t bit_cycles;
int tx_level = 1, tx_active, tx_bit;
std::uint8_t tx_shift;
avr_cycle_count_t tx_sample(avr_t *, avr_cycle_count_t when, void *)
{
if (tx_bit < 0) {
// Half a bit into the start bit: a real receiver re-samples here and
// abandons a false start. The device's own init produces one — DDR
// drives the pin low for the instructions until the idle level is
// written — and without this check that glitch decodes as a stray
// byte (and would read as first transmit activity under -w).
if (tx_level) {
tx_active = 0;
return 0;
}
window_first_tx();
tx_bit = 0;
return when + bit_cycles;
}
if (tx_bit < 8) {
tx_shift = static_cast<std::uint8_t>((tx_shift >> 1) | (tx_level ? 0x80 : 0));
if (++tx_bit < 8)
return when + bit_cycles;
// The byte is delivered at the stop bit's sampling point (9.5 bit
// times), where a hardware receiver raises its RXC — not sooner: a
// host answering before the stop bit would put its start bit on the
// wire while the device is still driving, which the device,
// transmitting, is not watching for.
return when + bit_cycles;
}
if (write(pty_master, &tx_shift, 1) != 1)
std::println(stderr, "device: pty write lost a byte");
tx_active = 0;
return 0;
}
// A USART owns its TxD pin whenever its transmitter is enabled, and the port
// register cannot drive it (§20.2 / Atmel-8271 §19.2) — which is why a
// bit-banged link deployed on those pins is mute until it clears UCSRnB.
// simavr wires a USART entirely through IRQs and never touches the port pin
// model, so the ownership does not exist there and the mute cannot happen:
// supply it, or the very state this models is untestable. The link spec's
// trailing @n names the USART; without one the pins are nobody's.
avr_uart_t *tx_owner;
bool tx_pin_taken()
{
if (!tx_owner)
return false;
if (avr_regbit_get(avr, tx_owner->txen))
return true;
// One-wire on the USART's RXD: RXEN forces the shared pin's direction to
// input (§20.7.3), so the firmware's drive goes nowhere until the
// release — the receive-side twin of the TXD hold.
return link_one_wire && avr_regbit_get(avr, tx_owner->rxen);
}
// simavr leaves TXEN set in UCSRnB out of reset, where silicon clears the
// whole register (§20.11.3) — which would hand the pin to a USART no code has
// enabled, making a freshly reset chip mute for reasons hardware does not
// have. Reset it the way the datasheet does, so the ownership starts from
// nobody's and only an application that really enables the USART takes it.
void reset_tx_owner()
{
if (tx_owner)
avr_regbit_clear(avr, tx_owner->txen);
}
void find_tx_owner()
{
for (avr_io_t *io = avr->io_port; io; io = io->next)
if (io->kind && std::string_view{io->kind} == "uart" &&
reinterpret_cast<avr_uart_t *>(io)->name == sw_tx_owner) {
tx_owner = reinterpret_cast<avr_uart_t *>(io);
reset_tx_owner();
return;
}
std::println(stderr, "device: no USART{} to own the software link's TX pin", sw_tx_owner);
}
void tx_hook(avr_irq_t *, std::uint32_t value, void *)
{
if (link_one_wire && (self_drive || !mcu_owns_line)) {
// The bridge's own drive coming back through the shared irq, or a
// transition while the line is the bridge's — either way not the
// firmware talking: the decoder sees an idle line.
tx_level = 1;
return;
}
if (tx_pin_taken()) { // the USART holds the line; the port write goes nowhere
tx_level = 1;
return;
}
int level = value & 1;
if (!tx_active && tx_level == 1 && level == 0) { // start edge, confirmed mid-bit
tx_active = 1;
tx_bit = -1;
avr_cycle_timer_register(avr, bit_cycles / 2, tx_sample, nullptr);
}
tx_level = level;
}
std::uint8_t rx_queue[8192];
unsigned rx_head, rx_tail; // ring: head = next to send
int rx_active, rx_bit;
std::uint8_t rx_byte;
void rx_start_next();
// Every level the bridge itself puts on the line goes through here, so the
// shared-pin decoder can tell its own drive from the firmware's.
void bridge_drive(int level)
{
self_drive = true;
avr_raise_irq(rx_pin, static_cast<std::uint32_t>(level));
self_drive = false;
}
avr_cycle_count_t rx_step(avr_t *, avr_cycle_count_t when, void *)
{
if (rx_bit < 8) {
bridge_drive((rx_byte >> rx_bit) & 1);
rx_bit++;
return when + bit_cycles;
}
if (rx_bit == 8) { // stop bit, plus one idle bit of margin
bridge_drive(1);
// The host-side tie: an FTDI adapter on a one-wire line reads every
// byte it transmits — supply that echo, which the host tool's
// --one-wire mode consumes as its wiring check.
if (link_one_wire && write(pty_master, &rx_byte, 1) != 1)
std::println(stderr, "device: pty echo lost a byte");
rx_bit++;
return when + 2 * bit_cycles;
}
rx_active = 0;
rx_start_next();
return 0;
}
void rx_start_next()
{
if (rx_active || rx_head == rx_tail)
return;
// The firmware is answering on the shared line: hold the byte — a real
// host's transmission waits out the reply on the wire too. The next
// poll_pty tick retries once the line is handed back.
if (link_one_wire && mcu_owns_line)
return;
rx_byte = rx_queue[rx_head];
rx_head = (rx_head + 1) % sizeof(rx_queue);
rx_active = 1;
rx_bit = 0;
bridge_drive(0); // start bit
avr_cycle_timer_register(avr, bit_cycles, rx_step, nullptr);
}
// The shared pin's direction is the line's ownership: DDR-out is the
// firmware driving a frame, DDR-in hands the line back to the bridge.
void on_ddr(avr_irq_t *, std::uint32_t value, void *)
{
const bool owns = (value >> sw_rx_bit) & 1;
if (mcu_owns_line && !owns)
bridge_drive(1); // hand-back: a turn-based host idles here, and the cache stays truthful
mcu_owns_line = owns;
// A byte held back while the firmware answered starts from the next
// poll_pty tick, never from inside the DDR write itself — the port
// model's own pull-up re-derivation runs right after this notify and
// would erase a start edge raised here.
}
// A reset abandons whatever the bridge was mid-transfer: bytes still queued
// for a chip that no longer has the context to receive them meaningfully,
// and a decode in progress on a TX line the reset may have already changed.
// The pending cycle timers must go with the state: avr_reset drops the TX
// output latch, whose falling edge starts a spurious decode before this
// runs, and a stale tx_sample would then interleave with the loader's first
// real answer through the shared shift state, corrupting it.
void bridge_reset()
{
avr_cycle_timer_cancel(avr, tx_sample, nullptr);
avr_cycle_timer_cancel(avr, rx_step, nullptr);
rx_head = rx_tail = 0;
rx_active = 0;
tx_active = 0;
tx_level = 1;
mcu_owns_line = false; // avr_reset zeroed DDR: every pin reads input again
// Re-drive the idle line through a forced transition: ioport pin irqs are
// IRQ_FLAG_FILTERED, and avr_reset zeroes the port latch while the irq
// keeps its pre-reset cached value — so a plain raise(1) against a cached
// 1 is dropped and the device reads the line stuck low. A loader entering
// calibration on that line measures reset-to-first-edge as one giant
// pulse and mis-locks or boots the application on the first real knock.
// No cycles run between the two raises, so the device only ever sees the
// final idle-high.
bridge_drive(0);
bridge_drive(1);
}
void poll_pty()
{
std::uint8_t chunk[256];
ssize_t got = read(pty_master, chunk, sizeof(chunk));
for (ssize_t i = 0; i < got; i++) {
unsigned next = (rx_tail + 1) % sizeof(rx_queue);
if (next == rx_head)
break; // full: the host will retry on timeout
rx_queue[rx_tail] = chunk[i];
rx_tail = next;
}
// Unconditional: a byte held back while the firmware owned a shared
// line restarts from here once the hand-back has happened.
rx_start_next();
}
// ------------------------------------------------------------------ main ---
[[noreturn]] void finish(int)
{
if (dump_path) {
std::FILE *f = std::fopen(dump_path, "wb");
if (f) {
std::fwrite(avr->flash, 1, avr->flashend + 1, f);
std::fclose(f);
}
avr_eeprom_desc_t ee = {.ee = nullptr, .offset = 0, .size = 0};
if (avr_ioctl(avr, AVR_IOCTL_EEPROM_GET, &ee) == 0 && ee.ee && ee.size) {
char path[512];
std::snprintf(path, sizeof(path), "%s.eeprom", dump_path);
f = std::fopen(path, "wb");
if (f) {
std::fwrite(ee.ee, 1, ee.size, f);
std::fclose(f);
}
}
}
if (!link_software)
uart_pty_stop(&uart_pty);
_exit(0);
}
} // namespace
int main(int argc, char *argv[])
{
bool link_given = false;
for (int opt; (opt = getopt(argc, argv, "l:w")) != -1;) {
if (opt == 'w') {
window_report = true;
continue;
}
if (opt != 'l' || parse_link(optarg) != 0) {
std::println(stderr, "device: bad link spec (usart0, usart1, sw, or sw:B0,B1 as RX,TX)");
return 2;
}
link_given = true;
}
int args = argc - optind;
if (args < 7 || args > 9) {
std::print(stderr,
"usage: {} [-l link] [-w] <pureboot.elf> <mcu> <hz> <base_hex> <page> <baud> <flash_dump>"
" [reset_hex] [resume_flash]\n"
" -l link: usart0 | usart1 | sw[:B0,B1[@0]] (RX,TX, then the USART owning\n"
" them); default: the chip's own\n"
" -w: print PB_WINDOW_TX <cycle> at the first transmit activity and\n"
" free-run idle time (window measurement mode)\n"
" reset_hex: reset vector (default: base with a boot section, else 0)\n"
" resume_flash: raw full-flash image loaded instead of the ELF — a prior\n"
" run's dump, for power-fail resume tests\n",
argv[0]);
return 2;
}
argv += optind - 1; // argv[1] is the ELF again, whatever was parsed
const std::string_view mcu_name = argv[2];
auto base = static_cast<std::uint32_t>(std::strtoul(argv[4], nullptr, 0));
auto page = static_cast<unsigned>(std::atoi(argv[5]));
auto baud = static_cast<unsigned>(std::atoi(argv[6]));
dump_path = argv[7];
const bool is_mega = mcu_name.starts_with("atmega");
if (!link_given)
link_software = !is_mega; // the chips' natural links: USART0, or PB0/PB1
avr = avr_make_mcu_by_name(mcu_name.data());
if (!avr) {
std::println(stderr, "device: no {} core", mcu_name);
return 1;
}
avr_init(avr);
avr->frequency = static_cast<std::uint32_t>(std::strtoul(argv[3], nullptr, 0));
std::memset(avr->flash, 0xff, avr->flashend + 1); // real flash powers up erased
if (args > 8) {
// Resume: the full flash image of an interrupted prior run.
std::FILE *f = std::fopen(argv[9], "rb");
if (!f || std::fread(avr->flash, 1, avr->flashend + 1, f) == 0) {
std::println(stderr, "device: cannot read {}", argv[9]);
return 1;
}
std::fclose(f);
} else {
elf_firmware_t fw{};
if (elf_read_firmware(argv[1], &fw) != 0) {
std::println(stderr, "device: cannot read {}", argv[1]);
return 1;
}
// An image past flash end would smash the simulator's heap and turn
// into phantom peripheral behavior (lessons: believe the size gate
// first) — refuse it loudly instead.
if (base + fw.flashsize > avr->flashend + 1) {
std::println(stderr, "device: {} B at {:#x} runs past flash end {:#x} — image does not fit its slot",
fw.flashsize, base, avr->flashend);
return 1;
}
std::memcpy(avr->flash + base, fw.flash, fw.flashsize);
}
// The boot-sectioned megas enter the loader in hardware (BOOTRST, not
// modeled — the argument picks the modeled fuse's target); the tinies
// and the boot-section-less m48s reset to word 0 like silicon — erased
// flash walks up into the loader, and after the host's surgery the
// patched vector routes there.
const bool boot_section = is_mega && !mcu_name.starts_with("atmega48");
reset_pc = args > 7 ? static_cast<std::uint32_t>(std::strtoul(argv[8], nullptr, 0)) : (boot_section ? base : 0);
avr->pc = reset_pc;
avr->codeend = avr->flashend;
// Erased EEPROM, as hardware powers up (simavr zeroes it).
std::uint8_t blank[1024];
std::memset(blank, 0xff, sizeof(blank));
avr_eeprom_desc_t seed = {.ee = blank, .offset = 0, .size = 0};
if (avr_ioctl(avr, AVR_IOCTL_EEPROM_GET, &seed) == 0 && seed.size <= sizeof(blank)) {
seed.ee = blank;
avr_ioctl(avr, AVR_IOCTL_EEPROM_SET, &seed);
}
// The megas carry simavr's avr_flash module (and its two gaps the wrap
// above fixes); the tinies get the NVM module simavr lacks. Which serial
// bridge runs is the link's business, not the chip class's.
if (is_mega) {
fix_mega_flash_erase();
} else {
nvm.page = page;
std::memset(nvm.buffer, 0xff, sizeof(nvm.buffer));
nvm.io.kind = "tiny_nvm";
nvm.io.ioctl = nvm_ioctl;
avr_register_io(avr, &nvm.io);
}
if (!link_software) {
// POLL_SLEEP paces an idle-polling loader in host real time (a
// no-hardware CPU-saving hack); clear it so cycles run free.
std::uint32_t flags = 0;
avr_ioctl(avr, AVR_IOCTL_UART_GET_FLAGS(uart_digit), &flags);
flags &= ~AVR_UART_FLAG_POLL_SLEEP;
avr_ioctl(avr, AVR_IOCTL_UART_SET_FLAGS(uart_digit), &flags);
// simavr leaves TXEN set out of reset where silicon clears the whole
// UCSR#B (§20.11.3). Harmless to a loader that enables TXEN itself —
// but a half-duplex build's receiver-only init then *drops* TXEN,
// and this uart model clears UDRE on that edge and never re-raises
// it on a later enable: the first transmitter after the hand-over
// waits UDRE forever, a wedge silicon does not have. Start from the
// datasheet's zero, as the software bridge's tx-owner model does.
for (avr_io_t *io = avr->io_port; io; io = io->next)
if (io->kind && std::string_view{io->kind} == "uart" &&
reinterpret_cast<avr_uart_t *>(io)->name == uart_digit)
hw_uart = reinterpret_cast<avr_uart_t *>(io);
if (hw_uart)
avr_regbit_clear(avr, hw_uart->txen);
uart_pty_init(avr, &uart_pty);
uart_pty_connect(&uart_pty, uart_digit);
if (window_report)
avr_irq_register_notify(avr_io_getirq(avr, AVR_IOCTL_UART_GETIRQ(uart_digit), UART_IRQ_OUTPUT),
window_uart_hook, nullptr);
std::println("PB_PTY {}", uart_pty.pty.slavename);
} else {
bit_cycles = (avr->frequency + baud / 2) / baud; // matches uart.hpp's own rounding exactly
if (sw_tx_owner)
find_tx_owner();
rx_pin = avr_io_getirq(avr, AVR_IOCTL_IOPORT_GETIRQ(sw_rx_port), static_cast<unsigned>(sw_rx_bit));
avr_irq_register_notify(
avr_io_getirq(avr, AVR_IOCTL_IOPORT_GETIRQ(sw_tx_port), static_cast<unsigned>(sw_tx_bit)), tx_hook,
nullptr);
if (link_one_wire)
avr_irq_register_notify(avr_io_getirq(avr, AVR_IOCTL_IOPORT_GETIRQ(sw_rx_port), IOPORT_IRQ_DIRECTION_ALL),
on_ddr, nullptr);
bridge_drive(1); // idle line
int slave;
struct termios raw;
cfmakeraw(&raw);
if (openpty(&pty_master, &slave, nullptr, &raw, nullptr) != 0) {
std::println(stderr, "device: openpty failed");
return 1;
}
fcntl(pty_master, F_SETFL, O_NONBLOCK);
std::println("PB_PTY {}", ttyname(slave));
}
std::fflush(stdout);
std::signal(SIGTERM, finish);
std::signal(SIGINT, finish);
std::signal(SIGUSR1, request_reset); // an external reset line, for the tests
long since_poll = 0;
for (;;) {
int state = avr_run(avr);
if (state == cpu_Done || state == cpu_Crashed)
break;
if (reset_requested) {
reset_requested = 0;
avr_reset(avr);
avr->pc = reset_pc;
if (!link_software) { // reset restores the pacing hack; re-clear it
std::uint32_t flags = 0;
avr_ioctl(avr, AVR_IOCTL_UART_GET_FLAGS(uart_digit), &flags);
flags &= ~AVR_UART_FLAG_POLL_SLEEP;
avr_ioctl(avr, AVR_IOCTL_UART_SET_FLAGS(uart_digit), &flags);
if (hw_uart) // and simavr's bogus reset TXEN (§20.11.3: zero)
avr_regbit_clear(avr, hw_uart->txen);
} else {
bridge_reset();
reset_tx_owner();
}
}
if (link_software && ++since_poll >= 2000) {
since_poll = 0;
poll_pty();
// An unthrottled idle simulation runs the activation window out
// from under the host's real-time knock cadence: a 1 MHz build's
// 8 s window is 8 M cycles — tens of wall milliseconds — so a
// first knock lost to an in-flight reset misses the window
// entirely. Pace the simulation only while the bridge is fully
// quiet (nothing decoding, nothing queued); transfers keep full
// speed, and a quiet window stretches toward real time.
if (!window_report && !rx_active && !tx_active && rx_head == rx_tail)
usleep(200);
}
}
finish(0);
}

212
test/test_handshake.py Normal file
View File

@@ -0,0 +1,212 @@
#!/usr/bin/env python3
"""Host-tool activation handshake: bounded against a line that misbehaves.
`_handshake` drains the line after it sees a prompt, to absorb a real loader's
trailing bytes before it asks for the identity. That drain must be bounded: a
target that never falls quiet — a board stuck in a reset loop presents exactly
this, ~60 reboots/s of UART-reset garbage in which a stray 0x2b reads as a
prompt — otherwise spins the tool forever. Regression for that hang, plus a
control that a well-behaved loader still connects.
The handshake must also survive its own leftovers: after `--stay` the loader's
final prompt can still be in the USB pipeline when the next invocation opens
the port, and on a board wired to reset on open, that opening starts a fresh
activation window the stale prompt then betrays — the tool commits to an
identity read against a device that never heard its knock, and what it finally
collects is the application's banner. StaleDTRPort is that moment as a port.
Stdlib only, no device: host-tool logic, so it runs on every chip's preset
beside pureboot.planner.
"""
import importlib.util
import pathlib
import threading
import time
PB = pathlib.Path(__file__).resolve().parents[1] / "pureboot" / "pureboot.py"
_spec = importlib.util.spec_from_file_location("pureboot", PB)
pb = importlib.util.module_from_spec(_spec)
_spec.loader.exec_module(pb)
P = F = 0
def check(name, ok):
global P, F
P, F = P + (1 if ok else 0), F + (0 if ok else 1)
print(f" [{'PASS' if ok else 'FAIL'}] {name}")
class FloodPort:
"""A line that never falls quiet: read_available always returns bytes, and
they contain a prompt. No identity ever completes."""
def flush_input(self):
pass
def write(self, data):
pass
def read_available(self, wait):
time.sleep(0.01) # a real read waits; keep the busy loop off a core
return b"+\x00\xff"
def read_exact(self, count, timeout):
raise pb.Error("no identity")
class LoaderPort:
"""A well-behaved pureboot 5: a prompt to the knock, then quiet, then the
slim identity (version 5 + m328p signature) and a closing prompt."""
def __init__(self):
self.pending = b""
self.exacts = 0
def flush_input(self):
self.pending = b""
def write(self, data):
if b"p" in data:
self.pending = b"+" # the prompt answers the knock, nothing else
def read_available(self, wait):
data, self.pending = self.pending, b""
return data
def read_exact(self, count, timeout):
self.exacts += 1
return b"\x05\x1e\x95\x0f" if self.exacts == 1 else b"+" # identity, then prompt
class StaleDTRPort:
"""`--stay`, then a fresh invocation on a board that resets when its port
opens. Three facts of that moment, all timed from the open: the previous
session's final prompt is still in transit and lands only after the
opening flush has already run; the reset holds the device off the line
at first, eating anything written before it completes; and the fresh
window is finite — once it expires the application boots and prints a
banner whose bytes are what a pending identity read collects. A
handshake that trusts the stale prompt spends the whole window waiting
on a device that never heard its knock; one that drains the line first
knocks into the real window and connects."""
STALE_AT = 0.02 # the leftover prompt becomes visible (post-flush)
READY_AT = 0.05 # reset complete, activation window opens
WINDOW = 1.0 # window length; expiry boots the application
def __init__(self):
self.t0 = time.monotonic()
# (visible-from, bytes): the line as a timed queue.
self.queue = [(self.t0 + self.STALE_AT, b"+")]
self.armed = False # a 'p' heard inside the window arms 'b'
self.booted = False
def _boot_check(self):
if not self.booted and time.monotonic() > self.t0 + self.READY_AT + self.WINDOW:
self.booted = True
self.queue.append((self.t0 + self.READY_AT + self.WINDOW,
b"W r libavr tempmon\r\n"))
def _visible(self):
self._boot_check()
now = time.monotonic()
return b"".join(d for t, d in self.queue if t <= now)
def _consume(self, n):
now = time.monotonic()
left = []
for t, d in self.queue:
if t <= now and n:
take = min(n, len(d))
d = d[take:]
n -= take
if d:
left.append((t, d))
self.queue = left
def flush_input(self):
self._consume(len(self._visible()))
def write(self, data):
self._boot_check()
now = time.monotonic()
if now < self.t0 + self.READY_AT or self.booted:
return # still in reset, or the application owns the line
if b"p" in data:
self.armed = True
self.queue.append((now + 0.01, b"+"))
if b"b" in data and self.armed:
# The slim identity (version 5 + m328p signature) and a prompt.
self.queue.append((now + 0.01, b"\x05\x1e\x95\x0f+"))
def read_available(self, wait):
deadline = time.monotonic() + wait
while True:
data = self._visible()
if data:
self._consume(len(data))
return data
if time.monotonic() >= deadline:
return b""
time.sleep(0.005)
def read_exact(self, count, timeout):
deadline = time.monotonic() + timeout
data = b""
while len(data) < count:
visible = self._visible()
if visible:
take = visible[:count - len(data)]
self._consume(len(take))
data += take
elif time.monotonic() >= deadline:
raise pb.Error(f"timeout: got {len(data)} of {count} bytes")
else:
time.sleep(0.005)
return data
def terminates(port, wait, budget):
"""Run connect_autobaud in a thread; True if it returns/raises within
`budget` seconds rather than hanging."""
done = threading.Event()
def run():
try:
pb.Loader(port).connect_autobaud(wait)
except Exception:
pass
finally:
done.set()
threading.Thread(target=run, daemon=True).start()
return done.wait(budget)
def main():
# the hang: a flooding target must not spin the drain forever. With wait=0.5
# the whole handshake has to give up well inside a few seconds.
check("flooding target: handshake terminates, drain is bounded",
terminates(FloodPort(), wait=0.5, budget=4.0))
# the control: a real loader still connects and reads identity.
info = pb.Loader(LoaderPort()).connect_autobaud(2.0)
check("well-behaved loader still connects (version 5)", info.version == 5)
# the stale prompt: a --stay leftover plus reset-on-open must not burn the
# fresh window — the pre-knock drain absorbs it and the first real knock
# lands inside the window.
try:
stale_ok = pb.Loader(StaleDTRPort()).connect(2.5).version == 5
except pb.Error as failed:
print(f" ({failed})")
stale_ok = False
check("stale --stay prompt + reset-on-open: connects in the fresh window", stale_ok)
print(f"\n {P} passed, {F} failed")
return 1 if F else 0
if __name__ == "__main__":
raise SystemExit(main())

360
test/test_planner.py Normal file
View File

@@ -0,0 +1,360 @@
#!/usr/bin/env python3
"""Host-tool unit tests — the planning and policy logic, no simulator:
programming orders and their recovery properties, the reset-vector surgery,
the staging composition, the boot-fuse decode, and the update preflight over
fuse combinations simavr cannot model.
Usage: test_planner.py <tool_py>
"""
import sys
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def expect_error(what, fn, *needles):
try:
fn()
except Exception as error:
for needle in needles:
if needle not in str(error):
fail(f"{what}: error lacks {needle!r}: {error}")
return
fail(f"{what}: no error raised")
def info_of(pb, base, page, patch, flash, signature=(0x1E, 0x93, 0x0B), word_flash=False, version=None):
scale = 2 if word_flash else 1
wire_base = base // scale
flags = (1 if patch else 0) | (2 if word_flash else 0)
# The EEPROM size comes from the signature, as it must: pureboot 5 derives
# the whole geometry from the signature rather than sending it, so a
# synthetic block that disagreed with its own signature would describe a
# chip that cannot exist.
eeprom = pb.CHIP_GEOMETRY[signature][2]
raw = bytes((0x50, 0x42, pb.NEWEST_LOADER if version is None else version,
*signature, page & 0xFF, wire_base & 0xFF, wire_base >> 8,
eeprom & 0xFF, eeprom >> 8, flags))
info = pb.Info(raw)
if info.flash_size != flash:
fail(f"info_of({base:#x}) decodes to {info.flash_size:#x} of flash, not {flash:#x}")
return info
def rjmp_decode(word, at, flash_words):
if word & 0xF000 != 0xC000:
fail(f"not an rjmp: {word:#06x}")
offset = word & 0x0FFF
if offset >= 0x800:
offset -= 0x1000
return (at + 1 + offset) % flash_words
def main():
import os
sys.path.insert(0, os.path.dirname(os.path.abspath(sys.argv[1])))
import pureboot as pb
tiny = info_of(pb, 0x1E00, 64, True, 0x2000)
mega = info_of(pb, 0x7E00, 128, False, 0x8000, signature=(0x1E, 0x95, 0x0F))
# Versioning: the block's third byte is the loader's version, and the tool
# speaks a window of them. Every version in the window decodes, so an older
# deployed loader stays usable; one above the window is refused by name,
# since which version changed the protocol is knowledge only the tool
# holds, and it holds none about a version it has never heard of.
for version in range(pb.OLDEST_LOADER, pb.NEWEST_LOADER + 1):
if info_of(pb, 0x1E00, 64, True, 0x2000, version=version).version != version:
fail(f"pureboot {version} does not decode")
expect_error(
"unknown loader version",
lambda: info_of(pb, 0x1E00, 64, True, 0x2000, version=pb.NEWEST_LOADER + 1),
f"pureboot {pb.NEWEST_LOADER + 1}",
"newer tool",
)
# mega_boot: BOOTSZ words and the BOOTRST sense per chip — the fuse byte
# index (EXTENDED on the x8 line except the m328s' HIGH, HIGH elsewhere)
# and the per-family ladders (Atmel-2486/2466/2503/2545/8271/DS40002065/
# 8272/8011/2593/42719). Synthetic 'F' replies: only the boot byte
# carries meaning.
cases = (
((0x1E, 0x93, 0x07), 0x2000, 3, {0b11: 0x1F00, 0b10: 0x1E00, 0b01: 0x1C00, 0b00: 0x1800}), # m8
((0x1E, 0x94, 0x03), 0x4000, 3, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}), # m16
((0x1E, 0x95, 0x02), 0x8000, 3, {0b11: 0x7E00, 0b10: 0x7C00, 0b01: 0x7800, 0b00: 0x7000}), # m32
((0x1E, 0x93, 0x0A), 0x2000, 2, {0b11: 0x1F00, 0b10: 0x1E00, 0b01: 0x1C00, 0b00: 0x1800}), # m88
((0x1E, 0x93, 0x0F), 0x2000, 2, {0b11: 0x1F00, 0b10: 0x1E00, 0b01: 0x1C00, 0b00: 0x1800}), # m88P
((0x1E, 0x94, 0x06), 0x4000, 2, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}), # m168/168A
((0x1E, 0x94, 0x0B), 0x4000, 2, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}), # m168P
((0x1E, 0x95, 0x14), 0x8000, 3, {0b11: 0x7E00, 0b10: 0x7C00, 0b01: 0x7800, 0b00: 0x7000}), # m328
((0x1E, 0x95, 0x0F), 0x8000, 3, {0b11: 0x7E00, 0b10: 0x7C00, 0b01: 0x7800, 0b00: 0x7000}), # m328P
((0x1E, 0x94, 0x0F), 0x4000, 3, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}), # m164A
((0x1E, 0x94, 0x0A), 0x4000, 3, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}), # m164P
((0x1E, 0x95, 0x15), 0x8000, 3, {0b11: 0x7E00, 0b10: 0x7C00, 0b01: 0x7800, 0b00: 0x7000}), # m324A
((0x1E, 0x96, 0x09), 0x10000, 3, {0b11: 0xFC00, 0b10: 0xF800, 0b01: 0xF000, 0b00: 0xE000}), # m644
((0x1E, 0x96, 0x0A), 0x10000, 3, {0b11: 0xFC00, 0b10: 0xF800, 0b01: 0xF000, 0b00: 0xE000}), # m644P
((0x1E, 0x97, 0x06), 0x20000, 3, {0b11: 0x1FC00, 0b10: 0x1F800, 0b01: 0x1F000, 0b00: 0x1E000}), # 1284
((0x1E, 0x97, 0x05), 0x20000, 3, {0b11: 0x1FC00, 0b10: 0x1F800, 0b01: 0x1F000, 0b00: 0x1E000}), # 1284P
)
for signature, flash, which, ladder in cases:
chip = info_of(pb, flash - pb.SLOT, 128 if flash < 0x20000 else 0, False, flash,
signature=signature, word_flash=flash > 0x10000)
for bits, start in ladder.items():
fuses = bytearray((0xFF, 0xFF, 0xFF, 0xFF))
fuses[which] = (0xF8 | (bits << 1)) & ~1
prog, at = pb.mega_boot(chip, bytes(fuses))
if not prog or at != start:
fail(f"mega_boot {signature[1]:02x}{signature[2]:02x} BOOTSZ={bits:02b} programmed: {prog} {at:#07x}")
fuses[which] |= 1
prog, at = pb.mega_boot(chip, bytes(fuses))
if prog or at != start:
fail(f"mega_boot {signature[1]:02x}{signature[2]:02b} unprogrammed: {prog} {at:#07x}")
# Word-addressed info decode: the 1284P's base and page ride the wire
# scaled — a 17-bit base halved into the block's two bytes, a 256-byte page
# spelled 0 — and its slot is the same 512 bytes as everywhere else, so its
# staging slot lands inside the 1 KiB minimum boot section.
big = info_of(pb, 0x1FE00, 0, False, 0x20000, signature=(0x1E, 0x97, 0x05), word_flash=True)
if big.page != 256 or big.base != 0x1FE00 or big.stage != 0x1FC00:
fail(f"word-addressed info decode: page {big.page}, base {big.base:#x}, stage {big.stage:#x}")
# Surgery: word 0 lands on the loader, the trampoline on the original
# entry — checked with an independent decoder.
app = bytes((0xC0 | 0x00, 0xC0)) + bytes((0x12,)) * 300 # rjmp .+0x00C0... entry word 0xC0C0
entry = rjmp_decode(app[0] | (app[1] << 8), 0, tiny.flash_size // 2)
pages = pb.plan_flash(app, tiny)
word0 = pages[0][0] | (pages[0][1] << 8)
if rjmp_decode(word0, 0, tiny.flash_size // 2) != tiny.base // 2:
fail("surgery: patched word 0 misses the loader")
tp = pages[tiny.base - 64]
tramp = tp[62] | (tp[63] << 8)
if rjmp_decode(tramp, (tiny.base - 2) // 2, tiny.flash_size // 2) != entry:
fail("surgery: trampoline misses the original entry")
expect_error("non-rjmp vector", lambda: pb.plan_flash(bytes((0x0C, 0x94)) + app[2:], tiny), "not an rjmp")
looped = bytearray(app)
word = pb.rjmp_to(0, tiny.base // 2, tiny.flash_size // 2)
looped[0], looped[1] = word & 0xFF, word >> 8
expect_error("read-back image", lambda: pb.plan_flash(bytes(looped), tiny), "read-back")
expect_error("oversize image", lambda: pb.plan_flash(bytes(0x1DFF), tiny), "application flash ends")
# Ordering: patched vector puts page 0 first and the trampoline second;
# a boot section puts page 0 last. Blank pages drop only when erased.
order = pb.covered(pages, tiny, skip_blank=False)
if order[0] != 0 or order[1] != tiny.base - 64:
fail(f"tiny order starts {order[:2]}, want page 0 then trampoline page")
if sorted(order[2:]) != order[2:]:
fail("tiny order tail not ascending")
mega_pages = pb.plan_flash(bytes((0xFF,)) * 600, mega)
morder = pb.covered(mega_pages, mega, skip_blank=False)
if morder[-1] != 0 or sorted(morder[:-1]) != morder[:-1]:
fail(f"mega order {morder}, want ascending with page 0 last")
blanky = {0: pages[0], 64: bytes((0xFF,)) * 64, 128: pages[128], tiny.base - 64: tp}
slim = pb.covered(blanky, tiny, skip_blank=True)
if 64 in slim or 0 not in slim or tiny.base - 64 not in slim:
fail(f"skip_blank order wrong: {slim}")
# Staging content: the identical image plus the through-word on a
# patched-vector chip; hard size clamps either way.
image = bytes(range(256)) * 2 # 512 B — too big for a tiny slot
expect_error("tiny staging size", lambda: pb.staging_content(image, tiny), "510")
staged = pb.staging_content(image[:508], tiny)
through = staged[510] | (staged[511] << 8)
if rjmp_decode(through, (tiny.base - 2) // 2, tiny.flash_size // 2) != tiny.base // 2:
fail("through-word misses the resident base")
if pb.staging_content(image, mega) != image:
fail("mega staging content should be the bare image")
expect_error("mega staging size", lambda: pb.staging_content(image + b"!", mega), "512")
# The image stamp: found in a synthetic binary, absent in noise. pureboot
# 5 stamps the magic, its version and the signature, and the geometry is
# looked up from there — so what comes back must equal what a live device
# of the same chip reports.
stamp = bytes((0x50, 0x42, pb.NEWEST_LOADER)) + bytes(tiny.signature)
binary = bytes((0xAA,)) * 10 + stamp + bytes((0xBB,)) * 10
found = pb.image_info(binary)
if found is None or found.raw != tiny.raw:
fail(f"image_info misreads the v{pb.NEWEST_LOADER} stamp: "
f"{found.raw.hex() if found else None} != {tiny.raw.hex()}")
if pb.image_info(bytes((0xAA,)) * 40) is not None:
fail("image_info invents a block")
# An older loader's image stays readable, so a deployed build can be
# identified and installed like any other.
old = info_of(pb, 0x1E00, 64, True, 0x2000, version=pb.OLDEST_LOADER)
found_old = pb.image_info(bytes((0xAA,)) * 10 + old.raw)
if found_old is None or found_old.version != pb.OLDEST_LOADER:
fail("image_info misses an older loader's block")
# loader_image must peel a padded image down to the slot content: a raw
# .bin padded from address 0 (or a whole-flash read-back with the loader
# resident at base) yields the same bytes as the bare slot image.
import tempfile
slot_image = bytes((0xAA,)) * 10 + tiny.raw + bytes((0xCC,)) * 40
padded = bytes((0xFF,)) * tiny.base + slot_image
with tempfile.NamedTemporaryFile(suffix=".bin", delete=False) as f:
f.write(padded)
padded_path = f.name
try:
if pb.loader_image(padded_path) != slot_image:
fail("loader_image does not peel a padded image to the slot content")
finally:
os.unlink(padded_path)
# Update preflight: the full fuse matrix, plus target mismatch.
other = info_of(pb, 0x1E00, 32, True, 0x2000)
expect_error("wrong-target image", lambda: pb.update_preflight(binary, other, None), "another target")
expect_error("mega needs fuses", lambda: pb.update_preflight(bytes((0xAA,)) * 8 + mega.raw, mega, None),
"--assume-fuses")
mega_image = bytes((0xAA,)) * 8 + mega.raw
def fuses(high):
return bytes((0xFF, 0xFF, 0xFF, high))
expect_error("BOOTSZ 512 B", lambda: pb.update_preflight(mega_image, mega, fuses(0xFE)),
"cannot self-update", "BOOTSZ")
notes = pb.update_preflight(mega_image, mega, fuses(0xFD)) # 1 KB, BOOTRST unprogrammed
if not any("BOOTRST unprogrammed" in n for n in notes):
fail(f"1K/unprogrammed notes: {notes}")
notes = pb.update_preflight(mega_image, mega, fuses(0xFC)) # 1 KB, BOOTRST programmed
if not any("staging slot" in n for n in notes):
fail(f"1K/programmed notes: {notes}")
notes = pb.update_preflight(mega_image, mega, fuses(0xFA)) # 2 KB, BOOTRST programmed
if not any("application flash" in n for n in notes):
fail(f"2K/programmed notes: {notes}")
if pb.update_preflight(bytes((0xAA,)) * 8 + tiny.raw, tiny, None) != []:
fail("tiny preflight should pass without fuses")
# The 1284s' smallest boot section (512 words) is exactly the resident
# slot plus its staging slot, so self-update is possible at the minimum
# BOOTSZ — no fuse step up, the 644's geometry. That holds only while a
# slot is 512 B: at 1 KiB the staging slot would fall outside the section
# and the preflight would refuse.
notes = pb.update_preflight(bytes((0xAA,)) * 8 + big.raw, big, fuses(0xFE))
if not any("staging slot" in n for n in notes):
fail(f"1284 minimum-BOOTSZ notes: {notes}")
# The walk-region refusal: BOOTRST aimed below the loader plus app data
# in the walk span errors without --force; erased spans and unprogrammed
# BOOTRST pass.
deep = {0x7800: bytes((1,)) * 128}
expect_error("walk region", lambda: pb.check_walk_region(deep, mega, fuses(0xFA), False), "--force")
pb.check_walk_region(deep, mega, fuses(0xFA), True)
pb.check_walk_region(deep, mega, fuses(0xFB), False) # BOOTRST unprogrammed
pb.check_walk_region({0x7800: bytes((0xFF,)) * 128}, mega, fuses(0xFA), False)
pb.check_walk_region(deep, mega, None, False) # fuses unknown: no check
# The repairing verify: a mismatched page is rewritten rather than raised,
# bounded so a fault that is not self-clearing cannot spin.
class FakeLoader:
"""A device whose first `bad` writes of any page land wrong."""
def __init__(self, info, bad):
self.info = info
self.bad = bad
self.flash = {}
self.writes = 0
def write_page(self, address, data):
self.writes += 1
self.flash[address] = bytes(len(data)) if self.bad > 0 else bytes(data)
self.bad -= 1
def read_flash(self, address, count):
return self.flash.get(address, bytes(count))
want = {0: bytes((i * 5) & 0xFF for i in range(128))}
# One bad write, then good: repaired in place, and the caller never sees
# an error. The rewrite is counted, so a silent no-op cannot pass.
device = FakeLoader(info_of(pb, 0x7E00, 128, False, 0x8000), bad=1)
device.write_page(0, want[0])
pb.verify_pages(device, want, repair=True)
if device.writes != 2:
fail(f"repairing verify made {device.writes} writes, expected 2")
# Without repair the same state raises, so the repair is what fixed it.
device = FakeLoader(info_of(pb, 0x7E00, 128, False, 0x8000), bad=1)
device.write_page(0, want[0])
expect_error("verify without repair", lambda: pb.verify_pages(device, want), "verify failed")
# A page that never comes good stops after RETRIES rewrites, and says so.
device = FakeLoader(info_of(pb, 0x7E00, 128, False, 0x8000), bad=99)
device.write_page(0, want[0])
expect_error(
"unrepairable page",
lambda: pb.verify_pages(device, want, repair=True),
"verify failed",
f"after {pb.RETRIES} retries",
)
if device.writes != pb.RETRIES + 1:
fail(f"unrepairable page took {device.writes} writes, expected {pb.RETRIES + 1}")
# The knock handshake against a device that is not listening yet — the
# state a port open leaves behind: it resets the chip into a fresh
# activation window while the previous session's prompt is still in
# flight, so the first knock is lost and a prompt arrives anyway.
class FakePort:
"""A loader in its activation window, plus `lost` leading writes the
reset swallows and one stale prompt still on the wire."""
def __init__(self, info_raw, lost=0, stale=b"", active=False):
self.info_raw = info_raw
self.lost = lost
self.inflight = bytearray(stale)
self.rx = bytearray()
self.active = active
self.last = None
def flush_input(self):
self.rx.clear()
def write(self, data):
if self.lost:
self.lost -= 1
return
for byte in bytes(data):
if not self.active:
self.active = self.last == ord("p") and byte == ord("b")
self.last = byte
if self.active:
self.rx += pb.PROMPT
elif byte == ord("b"):
self.rx += self.info_raw + pb.PROMPT
else:
self.rx += pb.PROMPT
def read_available(self, wait):
self.rx = self.inflight + self.rx # the stale prompt lands late
self.inflight.clear()
out, self.rx = bytes(self.rx), bytearray()
return out
def read_exact(self, count, timeout):
if len(self.rx) < count:
raise pb.Error(f"timeout: got {len(self.rx)} of {count} bytes")
out, self.rx = bytes(self.rx[:count]), self.rx[count:]
return out
raw = info_of(pb, 0x7E00, 128, False, 0x8000).raw
for what, port in (
("clean window", FakePort(raw)),
("stale prompt over a lost knock", FakePort(raw, lost=1, stale=pb.PROMPT)),
("live session", FakePort(raw, active=True)),
):
info = pb.Loader(port).connect(5)
if info.raw != raw:
fail(f"connect ({what}) returned {info.raw.hex()}")
# A device that never answers still says so, and a version the tool cannot
# speak is reported as such rather than retried into a timeout.
expect_error("dead device", lambda: pb.Loader(FakePort(raw, lost=99)).connect(0), "no answer")
old = bytes(raw[:2]) + bytes((pb.NEWEST_LOADER + 1,)) + bytes(raw[3:])
expect_error("unspeakable version", lambda: pb.Loader(FakePort(old)).connect(5), "needs a newer tool")
print("test_planner: all planner and policy checks pass")
if __name__ == "__main__":
main()

71
test/test_scan.py Normal file
View File

@@ -0,0 +1,71 @@
#!/usr/bin/env python3
"""--scan's walk and report logic, no simulator: the probe order, the rate
arithmetic, and the advice's direction. The rate physics itself is not
sim-testable — a pty carries bytes at any termios rate — so what the wire
would arbitrate is pinned here as logic instead.
Usage: test_scan.py <tool_py>
"""
import os
import sys
def fail(message):
print(f"FAIL: {message}")
sys.exit(1)
def main():
sys.path.insert(0, os.path.dirname(os.path.abspath(sys.argv[1])))
import pureboot as pb
walk = pb.scan_ratios()
if walk != [0, -2, 2, -4, 4, -6, 6, -8, 8, -10, 10]:
fail(f"probe walk is not built-rate-first, nearest-out: {walk}")
if pb.scan_rate(9600, 4) != 9984 or pb.scan_rate(9600, -4) != 9216:
fail("probe rate arithmetic")
if pb.scan_rate(115200, 0) != 115200:
fail("the built rate must probe unchanged")
# A loader answering fast means a fast oscillator: the trim goes down.
report = "\n".join(pb.scan_report(9600, 4, 6))
for needle in ("9984", "+4 %", "--baud 9984", "4 steps lower", "pureboot 6"):
if needle not in report:
fail(f"+4 % report lacks {needle!r}:\n{report}")
report = "\n".join(pb.scan_report(9600, -6, 6))
if "6 steps higher" not in report:
fail(f"-6 % report advises the wrong direction:\n{report}")
report = "\n".join(pb.scan_report(9600, 0, 6))
if "none" not in report or "steps" in report:
fail(f"an on-rate answer must advise no trim:\n{report}")
report = "\n".join(pb.scan_report(9600, 4, 6, clock=9600000))
if "9984000" not in report:
fail(f"the absolute clock must scale with the found ratio:\n{report}")
# The walk's rates mostly have no termios B-constant, so the POSIX port
# must set them through termios2 — probed on a pty, which accepts the
# ioctl without caring about the speed. Without this every off-nominal
# probe would abort the walk on the platform --scan matters most on.
if os.name == "posix":
import pty
master, slave = pty.openpty()
try:
port = pb.Port(os.ttyname(slave), pb.scan_rate(9600, 4))
port.set_baud(pb.scan_rate(9600, -4))
port.close()
except pb.Error as error:
fail(f"PosixPort refused an off-nominal probe rate: {error}")
finally:
os.close(master)
os.close(slave)
print("OK")
if __name__ == "__main__":
main()

167
test/test_update_link.py Executable file
View File

@@ -0,0 +1,167 @@
#!/usr/bin/env python3
"""Self-update across a link change: the host must follow the staging copy.
`--update-loader` installs the new image in the staging slot and then *enters
it* to have it rewrite the resident. That copy is the new image, so it speaks the
new image's baud and backend — but the host was talking to the *resident*. Where
the two differ, the host kept knocking at the old rate in the old mode, the
staging copy never answered, and the update stranded: staging installed, resident
untouched, and on a 1 KiB tiny the application region (which *is* the staging
slot there) already gone.
The wire cannot be probed for this — 512 bytes of position-independent code carry
no header saying what rate they were built for — so the operator declares it, and
a mismatch with nothing declared has to say so instead of reporting a bare
timeout.
Stdlib only, no device: host-tool logic, so it runs on every chip's preset beside
pureboot.planner.
"""
import importlib.util
import pathlib
PB = pathlib.Path(__file__).resolve().parents[1] / "pureboot" / "pureboot.py"
_spec = importlib.util.spec_from_file_location("pureboot", PB)
pb = importlib.util.module_from_spec(_spec)
_spec.loader.exec_module(pb)
IDENTITY = b"\x05\x1e\x95\x0f" # pureboot 5 + m328p signature
P = F = 0
def check(name, ok, detail=""):
global P, F
P, F = P + (1 if ok else 0), F + (0 if ok else 1)
print(f" [{'PASS' if ok else 'FAIL'}] {name}" + (f" — {detail}" if detail else ""))
class TwoLinkPort:
"""A board whose resident and staging copy answer on different links.
Only the rate currently set decides who can be heard, which is the physical
truth: a loader's bit timing is a cycle count, so a copy built for another
rate is unreadable until the host retunes. The knock bytes carry the mode, so
a backend mismatch is caught the same way.
"""
def __init__(self, resident=(57600, False), staged=(38400, False)):
self.resident, self.staged = resident, staged
self.baud = resident[0]
self.entered = False # a 'J' has handed control to the staging copy
self.switches = [] # every retune the host asked for
self.pending = bytearray() # what the device has queued to send
# --- the part under test needs this to exist at all
def set_baud(self, baud):
self.baud = baud
self.switches.append(baud)
def flush_input(self):
self.pending.clear()
def _audible(self, knock=None):
baud, autobaud = self.staged if self.entered else self.resident
if self.baud != baud:
return False
if knock is None:
return True
return knock == (bytes((pb.CALIBRATE, ord("p"))) if autobaud else b"pb")
def write(self, data):
data = bytes(data)
if data[:1] == b"J" and len(data) == 3:
# The resident acks the jump, then control moves to the copy.
if self._audible():
self.pending += pb.PROMPT
self.entered = True
elif data in (b"pb", bytes((pb.CALIBRATE, ord("p")))):
if self._audible(data):
self.pending += pb.PROMPT
elif data == b"b":
if self._audible():
self.pending += IDENTITY + pb.PROMPT
def read_available(self, wait):
out, self.pending = bytes(self.pending), bytearray()
return out
def read_exact(self, count, timeout):
if len(self.pending) < count:
raise pb.Error(f"timeout: got {len(self.pending)} of {count} bytes")
out, self.pending = bytes(self.pending[:count]), self.pending[count:]
return out
def connected(port):
"""A Loader already in session with the resident."""
loader = pb.Loader(port)
loader.connect(2.0)
return loader
def main():
# The control first: where the staged image keeps the resident's link, the
# flow works and needs no retune. This is the case that always passed, and
# it is what made the bug look like "self-update is broken" rather than
# "self-update cannot change the link".
port = TwoLinkPort(resident=(57600, False), staged=(57600, False))
loader = connected(port)
try:
loader.enter_copy(0x7C00, 2.0)
check("same link: staging copy entered", True)
except pb.Error as error:
check("same link: staging copy entered", False, str(error))
# A baud change, declared. The host must retune before knocking.
port = TwoLinkPort(resident=(57600, False), staged=(38400, False))
loader = connected(port)
try:
loader.enter_copy(0x7C00, 2.0, link=(38400, False))
check("baud change declared: entered after retuning", 38400 in port.switches,
f"switches={port.switches}")
except (pb.Error, TypeError) as error:
check("baud change declared: entered after retuning", False, repr(error))
# A backend change, declared: the knock itself has to become the calibration
# pulse, or an autobaud staging copy never hears a thing.
port = TwoLinkPort(resident=(57600, False), staged=(57600, True))
loader = connected(port)
try:
loader.enter_copy(0x7C00, 2.0, link=(57600, True))
check("backend change declared: entered as autobaud", True)
except (pb.Error, TypeError) as error:
check("backend change declared: entered as autobaud", False, repr(error))
# Nothing declared against a changed link: it still cannot work, but the
# error has to name the cause. A bare "no answer" sent the operator looking
# at the wiring while the application region sat erased.
port = TwoLinkPort(resident=(57600, False), staged=(38400, False))
loader = connected(port)
try:
loader.enter_copy(0x7C00, 0.3)
check("undeclared mismatch: reported", False, "unexpectedly succeeded")
except pb.Error as error:
text = str(error).lower()
check("undeclared mismatch: error names the link, not just a timeout",
"link" in text or "baud" in text or "backend" in text, str(error))
except TypeError as error:
check("undeclared mismatch: error names the link, not just a timeout",
False, repr(error))
# The resident's own link must be restored for the caller: a declared
# staging link is for the copy, and the tool talks to the new resident after.
port = TwoLinkPort(resident=(57600, False), staged=(38400, False))
loader = connected(port)
try:
loader.enter_copy(0x7C00, 2.0, link=(38400, False))
check("session records the link it is now speaking", loader.baud == 38400,
f"loader.baud={getattr(loader, 'baud', None)}")
except (pb.Error, TypeError, AttributeError) as error:
check("session records the link it is now speaking", False, repr(error))
print(f"\n {P} passed, {F} failed")
return 1 if F else 0
if __name__ == "__main__":
raise SystemExit(main())

252
test/tsbtest.py Normal file
View File

@@ -0,0 +1,252 @@
#!/usr/bin/env python3
"""End-to-end TSB protocol test: spawn the simavr device, speak the TinySafeBoot
wire protocol over its pty (as the real host tools do), and actually flash it.
Usage: tsbtest.py <device_binary> <tsb.elf> <boot_base_hex>
Exits 0 if every scenario passes.
"""
import os
import subprocess
import sys
import time
import serial
CONFIRM = 0x21 # '!'
REQUEST = 0x3F # '?'
KNOCK = 0x40 # '@'
PAGE = 128 # ATmega328P: 64 words
class Device:
"""The simavr runner, exposing UART0 as a pty. `config` seeds the config
page (via the device's TSB_CONFIG hook) so the password gate and emergency
erase are exercisable."""
def __init__(self, binary, elf, boot_base, dump="/tmp/tsb_dump.bin", config=None):
env = dict(os.environ)
if config is not None:
env["TSB_CONFIG"] = config
self.proc = subprocess.Popen(
[binary, elf, boot_base, dump],
stdout=subprocess.PIPE, stderr=subprocess.STDOUT, text=True, env=env)
self.dump = dump
self.pty = None
deadline = time.time() + 5
while time.time() < deadline:
line = self.proc.stdout.readline()
if not line:
break
if line.startswith("TSB_PTY"):
self.pty = line.split()[1]
break
if not self.pty:
self.stop()
raise RuntimeError("device did not report a pty")
def stop(self):
self.proc.terminate()
try:
self.proc.wait(timeout=3)
except subprocess.TimeoutExpired:
self.proc.kill()
class Host:
"""A faithful TSB host, per the wire protocol."""
def __init__(self, pty):
self.s = serial.Serial(pty, 115200, timeout=1.5)
self.info = None
def _read(self, n):
data = self.s.read(n)
if len(data) != n:
raise AssertionError(f"expected {n} bytes, got {len(data)}: {data.hex()}")
return data
def activate(self):
self.s.reset_input_buffer()
self.s.write(b"@@@")
reply = self._read(17)
if reply[16] != CONFIRM:
raise AssertionError(f"activation reply not '!'-terminated: {reply.hex()}")
self.info = reply[:16]
return self.info
# Parsed info-block fields (host math from the spec).
@property
def pagesize(self):
return self.info[9] * 2
@property
def appflash(self):
return (self.info[10] | (self.info[11] << 8)) * 2
@property
def eeprom_size(self):
return (self.info[12] | (self.info[13] << 8)) + 1
def _expect(self, byte, what):
r = self._read(1)
if r[0] != byte:
raise AssertionError(f"{what}: expected {byte:#x}, got {r.hex()}")
# Host-paced page read ('f'/'e'): send '!', take a page, repeat; stop with
# anything else, then the Mainloop '!'.
def _read_pages(self, cmd, npages):
self.s.write(cmd.encode())
data = b""
for _ in range(npages):
self.s.write(bytes([CONFIRM]))
data += self._read(PAGE)
self.s.write(bytes([REQUEST])) # stop
self._expect(CONFIRM, f"{cmd} end")
return data
# Device-paced page write ('F'/'E'): device offers '?', host sends '!'+page,
# or anything else to stop.
def _write_pages(self, cmd, data):
if len(data) % PAGE:
data += b"\xff" * (PAGE - len(data) % PAGE)
self.s.write(cmd.encode())
for off in range(0, len(data), PAGE):
self._expect(REQUEST, f"{cmd} '?'")
self.s.write(bytes([CONFIRM]) + data[off:off + PAGE])
self._expect(REQUEST, f"{cmd} trailing '?'")
self.s.write(bytes([REQUEST])) # stop
self._expect(CONFIRM, f"{cmd} end")
def write_flash(self, data):
self._write_pages("F", data)
def read_flash(self, npages):
return self._read_pages("f", npages)
def write_eeprom(self, data):
self._write_pages("E", data)
def read_eeprom(self, npages):
return self._read_pages("e", npages)
def read_config(self):
self.s.write(b"c")
page = self._read(PAGE)
self._expect(CONFIRM, "c end")
return page
def write_config(self, data):
assert len(data) == PAGE
self.s.write(b"C")
self._expect(REQUEST, "C '?'")
self.s.write(bytes([CONFIRM]) + data)
echo = self._read(PAGE) # device echoes what it programmed
self._expect(CONFIRM, "C end")
return echo
# Activation when the config page carries a password: 3×'@' then the
# password bytes, then the info block + mainloop '!'.
def activate_password(self, password):
self.s.reset_input_buffer()
self.s.write(bytes([KNOCK, KNOCK, KNOCK]) + password)
reply = self._read(17)
if reply[16] != CONFIRM:
raise AssertionError(f"password activation not '!'-terminated: {reply.hex()}")
self.info = reply[:16]
return self.info
# A 0 byte where a password byte is expected requests emergency erase; the
# device asks for two confirmations, then wipes and returns to the mainloop.
def emergency_erase(self):
self.s.reset_input_buffer()
self.s.write(bytes([KNOCK, KNOCK, KNOCK, 0x00]))
self._expect(REQUEST, "emergency confirm 1")
self.s.write(bytes([CONFIRM]))
self._expect(REQUEST, "emergency confirm 2")
self.s.write(bytes([CONFIRM]))
self._expect(CONFIRM, "emergency mainloop ready")
def check(cond, msg):
if not cond:
raise AssertionError(msg)
print(f" ok: {msg}")
# A config page carrying a password "PW": appjump 0, timeout 0x40, password
# 0x50 0x57 terminated by 0xff.
PW_CONFIG = "0000405057ff"
PW_BYTES = bytes([0x50, 0x57])
def scenario_roundtrip(host):
"""Activation + info block + flash/EEPROM/config read-write round-trips, on
a device with a blank (erased) config page — the usual no-password case."""
info = host.activate()
check(info[0:3] == b"TSB", f"magic 'TSB' (got {info[0:3]!r})")
check(info[6:9] == bytes([0x1E, 0x95, 0x0F]), f"signature 1E 95 0F (got {info[6:9].hex()})")
check(info[14] == info[15], f"device-type bytes 14==15 (got {info[14]:#x},{info[15]:#x})")
check(host.pagesize == PAGE, f"page size {PAGE} (got {host.pagesize})")
check(host.eeprom_size == 1024, f"eeprom size 1024 (got {host.eeprom_size})")
print(f" info: {info.hex()} appflash={host.appflash} eeprom={host.eeprom_size}")
app = bytes(range(256)) # two pages of known data
host.write_flash(app)
check(host.read_flash(2) == app, "flash round-trip 2 pages")
edata = bytes((i * 7) & 0xFF for i in range(PAGE))
host.write_eeprom(edata)
check(host.read_eeprom(1) == edata, "eeprom round-trip 1 page")
cfg = bytes([0x00, 0x00, 0x40]) + b"\xff" * (PAGE - 3) # timeout 0x40, no password
check(host.write_config(cfg) == cfg, "config write echoes the programmed page")
check(host.read_config() == cfg, "config read-back matches")
def scenario_password(host):
"""A device whose config page carries a password activates only when the
host sends it after the knock."""
info = host.activate_password(PW_BYTES)
check(info[0:3] == b"TSB", f"password activation returns the info block (got {info[0:3]!r})")
def scenario_emergency(host):
"""Emergency erase (password 0-byte + two confirms) wipes flash, EEPROM and
the config page; the device stays alive in its boot section."""
host.emergency_erase()
check(host.read_config() == b"\xff" * PAGE, "config page wiped")
check(host.read_flash(1) == b"\xff" * PAGE, "application flash wiped")
check(host.read_eeprom(1) == b"\xff" * PAGE, "EEPROM wiped")
def main():
binary, elf, boot_base = sys.argv[1], sys.argv[2], sys.argv[3]
failures = []
# Each group runs on its own freshly-reset device (simavr reloads the ELF,
# so nothing persists between them); the password groups seed a config page.
groups = [
("round-trip", None, scenario_roundtrip),
("password activation", PW_CONFIG, scenario_password),
("emergency erase", PW_CONFIG, scenario_emergency),
]
for name, config, fn in groups:
print(f"--- {name} ---")
dev = Device(binary, elf, boot_base, config=config)
try:
fn(Host(dev.pty))
except AssertionError as e:
failures.append(f"{name}: {e}")
print(f" FAIL: {e}")
finally:
dev.stop()
if failures:
print(f"FAILED ({len(failures)})")
return 1
print("ALL PASS")
return 0
if __name__ == "__main__":
sys.exit(main())

45
tools/check.sh Executable file
View File

@@ -0,0 +1,45 @@
#!/bin/bash
# The port's gate: every chip's generated workflow — build, size matrix, and
# the simulator-driven protocol suites. --full adds the reflect-spot builds
# (libavr's rule: reflect compiles are bounded to its spot set, never the
# full matrix) and swaps the compact size matrix for the exhaustive
# clock × baud × backend cross product. libavr resolves from the `libavr/`
# submodule; LIBAVR_ROOT overrides it for a working tree.
set -e
cd "$(dirname "$0")/.."
full=0
[[ "$1" == "--full" ]] && { full=1; shift; export PUREBOOT_FULL_MATRIX=1; }
CHIPS=(attiny13 attiny13a attiny25 attiny45 attiny85
atmega8 atmega8a atmega16 atmega16a atmega32 atmega32a
atmega48 atmega48a atmega48p atmega48pa
atmega88 atmega88a atmega88p atmega88pa
atmega168 atmega168a atmega168p atmega168pa
atmega328 atmega328p
atmega164a atmega164p atmega164pa
atmega324a atmega324p atmega324pa
atmega644 atmega644a atmega644p atmega644pa
atmega1284 atmega1284p)
REFLECT_SPOT=(attiny13a attiny85 atmega8 atmega16a atmega32a atmega48pa
atmega88 atmega168pa atmega328p atmega164a atmega644p atmega1284)
for chip in "${CHIPS[@]}"; do
echo "==== $chip ===="
cmake --workflow --preset "$chip-generated" "$@"
done
if ((full)); then
for chip in "${REFLECT_SPOT[@]}"; do
echo "==== $chip reflect ===="
cmake --workflow --preset "$chip-reflect" "$@"
done
fi
# Every tree is freshly built now — the one moment the README's size table
# can be held to what the images measure (a per-preset ctest sees only its
# own chip; the table needs all of them, and ungated it drifts: a
# common-code shave moves every row at once with nothing over budget).
python3 tools/sizes.py check-readme
echo "check: every chip green"

103
tools/make_presets.py Executable file
View File

@@ -0,0 +1,103 @@
#!/usr/bin/env python3
"""Regenerate CMakePresets.json — one uniform pipeline per chip.
Every chip gets generated-mode configure/build/test presets and a workflow
running all three. Reflect-mode presets (configure + build, no tests — the
port's TUs compile identically; the sims prove nothing new there) exist for
libavr's reflect spot set only, mirroring its rule: the full reflect matrix
is never built, one chip per hardware class and pack vintage is.
Run from the repo root: tools/make_presets.py — or with --check, which
verifies the committed file matches this generator and edits nothing (the
ctest entry `presets.generated` runs that, so drift reds the gate).
"""
import json
import os
import sys
CHIPS = [
"attiny13", "attiny13a", "attiny25", "attiny45", "attiny85",
"atmega8", "atmega8a", "atmega16", "atmega16a", "atmega32", "atmega32a",
"atmega48", "atmega48a", "atmega48p", "atmega48pa",
"atmega88", "atmega88a", "atmega88p", "atmega88pa",
"atmega168", "atmega168a", "atmega168p", "atmega168pa",
"atmega328", "atmega328p",
"atmega164a", "atmega164p", "atmega164pa",
"atmega324a", "atmega324p", "atmega324pa",
"atmega644", "atmega644a", "atmega644p", "atmega644pa",
"atmega1284", "atmega1284p",
]
# libavr's REFLECT_SPOT (tools/check.sh): one chip per hardware class and
# pack vintage.
REFLECT_SPOT = [
"attiny13a", "attiny85", "atmega8", "atmega16a", "atmega32a",
"atmega48pa", "atmega88", "atmega168pa", "atmega328p", "atmega164a",
"atmega644p", "atmega1284",
]
def main():
configure = [{
"name": "base",
"hidden": True,
"generator": "Ninja",
"binaryDir": "${sourceDir}/build/${presetName}",
"toolchainFile": "${sourceDir}/libavr/cmake/avr-toolchain.cmake",
"cacheVariables": {
"CMAKE_BUILD_TYPE": "Release",
"CMAKE_EXPORT_COMPILE_COMMANDS": "ON",
"CMAKE_COLOR_DIAGNOSTICS": "ON",
},
}]
build, test, workflows = [], [], []
def add(chip, mode):
name = f"{chip}-{mode}"
configure.append({
"name": name,
"inherits": "base",
"cacheVariables": {
"LIBAVR_MCU": chip,
"LIBAVR_REFLECT": "ON" if mode == "reflect" else "OFF",
},
})
build.append({"name": name, "configurePreset": name})
steps = [{"type": "configure", "name": name}, {"type": "build", "name": name}]
if mode == "generated":
test.append({"name": name, "configurePreset": name, "output": {"outputOnFailure": True}})
steps.append({"type": "test", "name": name})
workflows.append({"name": name, "steps": steps})
for chip in CHIPS:
add(chip, "generated")
for chip in REFLECT_SPOT:
add(chip, "reflect")
# CMake rejects unknown fields in the presets root, $comment included, so
# the file cannot carry a generated-file marker; the --check ctest is the
# whole of rule 10's guard here.
presets = {
"version": 8,
"configurePresets": configure,
"buildPresets": build,
"testPresets": test,
"workflowPresets": workflows,
}
rendered = json.dumps(presets, indent=1) + "\n"
path = os.path.join(os.path.dirname(os.path.abspath(__file__)), "..", "CMakePresets.json")
if "--check" in sys.argv[1:]:
current = open(path).read() if os.path.exists(path) else ""
if current != rendered:
print("CMakePresets.json does not match its generator — run tools/make_presets.py")
return 1
return 0
with open(path, "w") as f:
f.write(rendered)
print(f"{len(CHIPS)} chips, {len(REFLECT_SPOT)} reflect: {os.path.normpath(path)}")
return 0
if __name__ == "__main__":
sys.exit(main())

265
tools/pbhw.py Executable file
View File

@@ -0,0 +1,265 @@
#!/usr/bin/env python3
"""Hardware acceptance suite for a pureboot deployment.
`tools/check.sh` proves the protocol under simavr on every chip. This proves one
*board*: that the loader actually installed on it answers, that the memories
round-trip over the real link, that the application it flashes runs afterwards,
and that the refusals which keep a 512-byte slot alive still fire. Run it once
when a board is brought up, and again whenever the deployment moves — a new
clock, a new backend, new pins.
Every check derives its bounds from the info block the loader itself reports, so
nothing here is per-chip: the same run covers a 1 KiB tiny whose application
region is 510 usable bytes and a 128 KiB mega whose flash needs a bank in the
selector.
**This overwrites the board's application flash and EEPROM.** Capture them first
with `pbrig.py backup`, which verifies what it captured.
tools/pbhw.py --programmer atmelice_isp --part t13 --port COM6 \
--autobaud --loader build/ab.bin --app build/pbapp.hex \
--marker APP
"""
from __future__ import annotations
import argparse
import pathlib
import sys
import tempfile
sys.path.insert(0, str(pathlib.Path(__file__).resolve().parent))
import pbrig # noqa: E402
class Suite:
def __init__(self, rig: pbrig.Rig, work: pathlib.Path):
self.rig = rig
self.work = work
self.results: list[tuple[str, bool, str]] = []
def check(self, name: str, ok: bool, detail: str = "") -> bool:
self.results.append((name, ok, detail))
print(f" {'PASS' if ok else 'FAIL'} {name}" + (f" {detail}" if detail else ""))
return ok
@staticmethod
def _brief(text: str, limit: int = 78) -> str:
return " | ".join(l.strip() for l in text.splitlines() if l.strip())[:limit]
# ----------------------------------------------------------------- checks
def identity(self) -> object | None:
"""The info block, which every later check takes its bounds from."""
module = pbrig.load_pureboot(self.rig.d.pureboot)
self.rig.reset()
port = self.rig.open_port() # wrapped for the echo where the line is shared
try:
loader = module.Loader(port)
if self.rig.d.autobaud:
loader.connect_autobaud(self.rig.d.wait)
else:
loader.connect(self.rig.d.wait)
info = loader.info
self.check("identity read", True, info.describe())
return info
except Exception as error: # noqa: BLE001 — a dead link is a result
self.check("identity read", False, str(error)[:70])
return None
finally:
try:
port.close()
except Exception:
pass
def scan(self) -> None:
"""The --scan walk against real termios and a real oscillator: every
probe rate must open a port (the off-nominal rates exist only through
termios2), and one probe must answer — the nominal on a healthy board,
a neighbor on a drifted one. The rig injects the one reset per probe
the operator supplies in the field; this is the rate physics the
simulator cannot arbitrate (a pty carries bytes at any rate), pinned
on silicon."""
module = pbrig.load_pureboot(self.rig.d.pureboot)
found = None
try:
for pct in module.scan_ratios():
rate = module.scan_rate(self.rig.d.baud, pct)
self.rig.reset()
try:
# Same wrap as identity(): on a shared line an undiscarded
# echo answers every rate a scan probes, so the walk would
# report the first one it tried.
port = self.rig.open_port(rate)
except module.Error as error:
self.check("scan opens every probe rate", False, f"{rate} Bd: {error}")
return
try:
module.Loader(port).connect(min(self.rig.d.wait, 6.0))
found = pct
break
except module.Error:
continue
finally:
port.close()
except Exception as error: # noqa: BLE001 — a rig hiccup is a result
self.check("scan walks the probe ladder", False, str(error)[:70])
return
self.check("scan finds the board's rate", found is not None,
"no probe answered" if found is None else f"{found:+d} % of {self.rig.d.baud} Bd")
def eeprom(self, info) -> None:
size = info.eeprom_size
if not size:
print(" skip EEPROM (this part has none)")
return
# A pattern no erase or partial write could produce by accident.
pattern = bytes((i * 7 + 3) & 0xFF for i in range(size))
image = self.work / "ee.bin"
image.write_bytes(pattern)
rc, out = self.rig.pureboot("--eeprom", str(image), "--verify-eeprom", str(image))
self.check(f"EEPROM write + verify ({size} B)", rc == 0, self._brief(out))
back = self.work / "ee-back.bin"
rc, out = self.rig.pureboot("--read-eeprom", str(back))
got = back.read_bytes() if back.exists() else b""
self.check("EEPROM reads back what was written", got == pattern, f"{len(got)} B")
self.rig.pureboot("--erase-eeprom")
erased = self.work / "ee-erased.bin"
self.rig.pureboot("--read-eeprom", str(erased))
got = erased.read_bytes() if erased.exists() else b""
self.check("EEPROM erase leaves 0xff", got == b"\xff" * size, f"{len(got)} B")
def application(self, info, app: pathlib.Path, marker: str,
marker_wait: float = 2.5) -> None:
rc, out = self.rig.pureboot("--flash", str(app), "--verify-flash", str(app))
self.check(f"application flash + verify ({app.name})", rc == 0, self._brief(out))
if marker:
# The tool hands over as it ends its session, so the application is
# already running — but only on a board whose DTR is unwired, where
# opening a port simply listens. Where DTR *is* wired to reset (an
# Arduino, most USB-serial dev boards), this open resets the part
# and the activation window comes first, so a marker emitted once at
# startup happens on the far side of a wait this cannot know the
# length of: the window is a compile-time constant and nothing on
# the wire reports it. Hence --marker-wait, and a fixture that
# repeats its banner (PUREBOOT_HEARTBEAT) rather than saying it once.
data = self.rig.capture(seconds=marker_wait)
seen = marker.encode() in data
sample = "".join(chr(b) if 32 <= b < 127 else "." for b in data[:40])
self.check(f"application runs (emits {marker!r})", seen,
f"|{sample}|" if seen or data else
f"nothing in {marker_wait:g} s — if this board resets when its port "
f"opens, that wait has to outlast the activation window")
back = self.work / "app-back.bin"
rc, out = self.rig.pureboot("--read-flash", str(back))
got = back.read_bytes() if back.exists() else b""
self.check("application flash reads back", rc == 0 and len(got) == info.base,
f"{len(got)} B of {info.base}")
def erase_and_guard(self, info, loader_image: pathlib.Path | None) -> None:
rc, out = self.rig.pureboot("--erase-flash")
self.check("application region erases", rc == 0, self._brief(out))
# The slot must be untouched by an application erase, which only an
# independent read can show — so this one goes over ISP, not the link.
whole = self.work / "whole.bin"
if not self.rig.read_memory("flash", whole, "r"):
self.check("loader slot survives the erase", False, "ISP read failed")
return
image = whole.read_bytes()
image += b"\xff" * (info.flash_size - len(image))
# Erased application flash, up to the trampoline word the host composes
# on a patched-vector part.
limit = info.base - 2 if info.patch_vector else info.base
self.check("erased application region is 0xff",
set(image[0:limit]) <= {0xFF}, f"0x0000..{limit:#06x}")
if loader_image and loader_image.exists():
want = loader_image.read_bytes()
got = image[info.base:info.base + len(want)]
self.check("loader slot survives the erase", got == want,
f"{len(want)} B at {info.base:#06x}")
else:
print(" skip loader slot comparison (pass --loader <image.bin>)")
def refusals(self, info) -> None:
# One word too many: a patched-vector part spends the slot's last word
# on the trampoline, so its application stops two bytes short.
limit = info.base - 2 if info.patch_vector else info.base
oversized = self.work / "oversized.bin"
oversized.write_bytes(bytes(limit + 2))
rc, out = self.rig.pureboot("--flash", str(oversized))
self.check(f"image over {limit} B refused", rc != 0, self._brief(out))
# ------------------------------------------------------------------- run
def run(self, app: pathlib.Path | None, loader_image: pathlib.Path | None,
marker: str, marker_wait: float = 2.5) -> int:
print("identity")
info = self.identity()
if info is None:
print("\nthe loader never answered; nothing below can be trusted")
return 1
if not self.rig.d.autobaud:
print("\nscan")
self.scan()
print("\nEEPROM")
self.eeprom(info)
if app:
print("\napplication")
self.application(info, app, marker, marker_wait)
else:
print("\nskip application checks (pass --app <image.hex>)")
print("\nerase and the write guard")
self.erase_and_guard(info, loader_image)
print("\nrefusals")
self.refusals(info)
passed = sum(1 for _, ok, _ in self.results if ok)
print(f"\n{passed}/{len(self.results)} passed")
return 0 if passed == len(self.results) else 1
def main(argv: list[str] | None = None) -> int:
parser = argparse.ArgumentParser(
description="hardware acceptance suite for one pureboot deployment",
epilog="overwrites the board's application flash and EEPROM — back them up first")
pbrig.Deployment.add_arguments(parser)
parser.add_argument("--app", type=pathlib.Path,
help="application image to flash (test/pbapp.cpp built for this deployment)")
parser.add_argument("--loader", type=pathlib.Path,
help="the resident loader's .bin, to prove the slot survives an erase")
parser.add_argument("--marker", default="",
help="text the application emits when it runs, e.g. APP")
parser.add_argument("--marker-wait", type=float, default=2.5,
help="seconds to listen for it. On a board whose DTR is wired to "
"reset, opening the port resets the part, so this must outlast "
"the activation window (default 2.5)")
args = parser.parse_args(argv)
rig = pbrig.Rig(pbrig.Deployment.from_args(args))
print(f"rig: {args.part} on {args.programmer}, link {args.port} at {args.baud} Bd"
f"{' (autobaud)' if args.autobaud else ''}")
print("this overwrites the application flash and EEPROM\n")
with tempfile.TemporaryDirectory(prefix="pbhw-") as temporary:
return Suite(rig, pathlib.Path(temporary)).run(args.app, args.loader, args.marker,
args.marker_wait)
if __name__ == "__main__":
try:
sys.exit(main())
except pbrig.Error as error:
print(f"error: {error}", file=sys.stderr)
sys.exit(2)

450
tools/pbrig.py Executable file
View File

@@ -0,0 +1,450 @@
#!/usr/bin/env python3
"""Hardware rig driver for pureboot: an ISP programmer beside a serial link.
The simulated suites (`test/pb*.py`) prove the protocol; this drives the same
loader on real silicon, where the things a cycle-exact simulator cannot model
live — an RC oscillator off its nominal, a reset edge that has to come from
somewhere, a serial bridge with its own idea of what a baud is.
Nothing here knows a port name, a part or a programmer. Every deployment fact
arrives from the command line or the environment, so the same script serves any
board: see `Deployment`. As a module it is the reset/flash/talk primitives that
`pbhw.py` builds its acceptance suite from; as a command it is the handful of
one-shot operations worth having on a rig — most importantly `backup`, which is
the only thing standing between a fuse experiment and an unrecoverable part.
Two rig facts are encoded here because they are not guessable and cost a
session each to learn:
* **An ISP access resets the part**, and it runs again the moment the programmer
releases it. That is the only reset edge available when the serial adapter's
DTR is not wired to reset — so a loader session begins with an ISP touch and
knocks immediately after, which is what `Rig.pureboot()` does.
* **avrdude splits `-U memory:op:file:format` on colons**, so a Windows path's
drive letter breaks the spec. Every file argument is therefore passed as a
bare filename with avrdude run in that file's own directory.
"""
from __future__ import annotations
import argparse
import dataclasses
import importlib.util
import os
import pathlib
import subprocess
import sys
import time
HERE = pathlib.Path(__file__).resolve().parent
DEFAULT_PUREBOOT = HERE.parent / "pureboot" / "pureboot.py"
# Memories worth capturing before an experiment, and the format each is read in.
# Fuses and lock are per-part: a part without an extended fuse simply fails that
# one read, which `backup` reports and steps over rather than aborting on.
BACKUP_MEMORIES = (
("flash", "i", "hex"),
("flash", "r", "bin"),
("eeprom", "i", "hex"),
("eeprom", "r", "bin"),
("lfuse", "h", "hex"),
("hfuse", "h", "hex"),
("efuse", "h", "hex"),
("lock", "h", "hex"),
("calibration", "h", "hex"),
)
class Error(Exception):
pass
def bitclock_for(hz: int) -> str:
"""A safe ISP bitclock for a part *currently running* at `hz`.
SCK must stay under a quarter of the target clock, so the bitclock follows
the clock in force — not the one about to be fused in. Halving that ceiling
again costs nothing on a link that moves a few hundred bytes and buys margin
against an oscillator that is already known to be off its nominal.
"""
ceiling = hz // 8
for candidate in (1000, 4000, 8000, 32000, 125000, 400000):
if candidate <= ceiling:
best = candidate
else:
break
else:
best = 400000
if ceiling < 1000:
raise Error(f"a part at {hz} Hz is too slow to reach over ISP safely")
return f"{best // 1000}kHz"
@dataclasses.dataclass
class Deployment:
"""Everything about one board. No default names a real device."""
port: str = "" # serial device the loader speaks on
baud: int = 57600 # host rate; for autobaud, the rate to drive
autobaud: bool = False # send the calibration pulse instead of p+b
one_wire: bool = False # shared line: the host discards its own echo
programmer: str = "" # avrdude -c
part: str = "" # avrdude -p
avrdude: str = "avrdude"
bitclock: str = "125kHz" # see bitclock_for()
pureboot: pathlib.Path = DEFAULT_PUREBOOT
wait: int = 12 # seconds the host keeps knocking
@classmethod
def from_env(cls) -> "Deployment":
"""Environment defaults, so a rig's facts live in one place per machine."""
return cls(
port=os.environ.get("PUREBOOT_PORT", ""),
baud=int(os.environ.get("PUREBOOT_BAUD", "57600")),
autobaud=os.environ.get("PUREBOOT_AUTOBAUD", "") not in ("", "0"),
one_wire=os.environ.get("PUREBOOT_ONE_WIRE", "") not in ("", "0"),
programmer=os.environ.get("PUREBOOT_PROGRAMMER", ""),
part=os.environ.get("PUREBOOT_PART", ""),
avrdude=os.environ.get("AVRDUDE", "avrdude"),
bitclock=os.environ.get("PUREBOOT_BITCLOCK", "125kHz"),
pureboot=pathlib.Path(os.environ.get("PUREBOOT_TOOL", str(DEFAULT_PUREBOOT))),
)
@staticmethod
def add_arguments(parser: argparse.ArgumentParser) -> None:
"""Deployment flags, shared by this tool and pbhw.py."""
env = Deployment.from_env()
parser.add_argument("--port", default=env.port, help="serial device the loader speaks on")
parser.add_argument("--baud", type=int, default=env.baud,
help="host rate (for autobaud, the rate to drive)")
parser.add_argument("--autobaud", action="store_true", default=env.autobaud,
help="send the calibration pulse instead of the p+b knock")
parser.add_argument("--one-wire", action="store_true", default=env.one_wire,
help="shared line: pass the tool its echo discard")
parser.add_argument("--programmer", default=env.programmer, help="avrdude -c, e.g. atmelice_isp")
parser.add_argument("--part", default=env.part, help="avrdude -p, e.g. t13 or m328p")
parser.add_argument("--avrdude", default=env.avrdude, help="path to avrdude")
parser.add_argument("--bitclock", default=env.bitclock, help="ISP bitclock, e.g. 125kHz or 8kHz")
parser.add_argument("--pureboot", type=pathlib.Path, default=env.pureboot,
help="path to pureboot.py")
parser.add_argument("--wait", type=int, default=env.wait, help="seconds to keep knocking")
@classmethod
def from_args(cls, args: argparse.Namespace) -> "Deployment":
return cls(port=args.port, baud=args.baud, autobaud=args.autobaud,
one_wire=args.one_wire,
programmer=args.programmer, part=args.part, avrdude=args.avrdude,
bitclock=args.bitclock, pureboot=args.pureboot, wait=args.wait)
def load_pureboot(path: pathlib.Path = DEFAULT_PUREBOOT):
"""The host tool as a module — its Port and Loader, not a subprocess.
Used where a subprocess cannot express what is needed: a poke followed by a
peek in the *same* session, or a raw read at an arbitrary baud.
"""
spec = importlib.util.spec_from_file_location("pureboot", path)
if spec is None or spec.loader is None:
raise Error(f"cannot load the host tool from {path}")
module = importlib.util.module_from_spec(spec)
spec.loader.exec_module(module)
return module
class Rig:
"""One board: its programmer on one side, its serial link on the other."""
def __init__(self, deployment: Deployment):
self.d = deployment
if not deployment.programmer or not deployment.part:
raise Error("a rig needs --programmer and --part")
# ------------------------------------------------------------- programmer
def avrdude(self, *args: str, cwd: pathlib.Path | None = None,
bitclock: str | None = None, timeout: int = 300) -> subprocess.CompletedProcess:
command = [self.d.avrdude, "-c", self.d.programmer, "-p", self.d.part,
"-B", bitclock or self.d.bitclock, *args]
return subprocess.run(command, capture_output=True, text=True,
cwd=None if cwd is None else str(cwd), timeout=timeout)
@staticmethod
def _ok(result: subprocess.CompletedProcess) -> bool:
return result.returncode == 0
def reset(self, bitclock: str | None = None) -> None:
"""An ISP access, which resets the part; it runs when avrdude exits."""
self.avrdude("-U", "signature:r:-:h", bitclock=bitclock)
def signature(self, bitclock: str | None = None) -> str:
result = self.avrdude("-U", "signature:r:-:h", bitclock=bitclock)
for line in reversed(result.stdout.splitlines()):
if line.strip().startswith("0x"):
return line.strip()
raise Error(f"no signature read: {(result.stderr or result.stdout).strip()[:200]}")
def read_memory(self, memory: str, destination: pathlib.Path, fmt: str = "r",
bitclock: str | None = None) -> bool:
"""Read `memory` into `destination`, whose directory avrdude runs in."""
destination = pathlib.Path(destination).resolve()
destination.parent.mkdir(parents=True, exist_ok=True)
result = self.avrdude("-U", f"{memory}:r:{destination.name}:{fmt}",
cwd=destination.parent, bitclock=bitclock)
# A memory the part does not have (a tiny's extended fuse) leaves avrdude
# happy and the file empty. An empty capture is a miss, not a backup.
return self._ok(result) and destination.exists() and destination.stat().st_size > 0
def write_memory(self, memory: str, source: pathlib.Path, fmt: str = "i",
erase: bool = False, bitclock: str | None = None) -> bool:
source = pathlib.Path(source).resolve()
args = ["-U", f"{memory}:w:{source.name}:{fmt}"]
if erase:
args.insert(0, "-e")
result = self.avrdude(*args, cwd=source.parent, bitclock=bitclock)
return "verified" in (result.stdout + result.stderr)
def flash_hex(self, image: pathlib.Path, erase: bool = True,
bitclock: str | None = None) -> bool:
return self.write_memory("flash", image, "i", erase=erase, bitclock=bitclock)
def read_fuses(self, bitclock: str | None = None) -> dict[str, str]:
out: dict[str, str] = {}
for fuse in ("lfuse", "hfuse", "efuse", "lock"):
result = self.avrdude("-U", f"{fuse}:r:-:h", bitclock=bitclock)
values = [l.strip() for l in result.stdout.splitlines() if l.strip().startswith("0x")]
if values:
out[fuse] = values[-1]
return out
def write_fuses(self, bitclock: str | None = None, **fuses: str) -> bool:
"""Write named fuses. A fuse change moves the clock the *next* access is
timed against, so pass a bitclock safe for both sides of the change."""
args: list[str] = []
for name, value in fuses.items():
args += ["-U", f"{name}:w:{value}:m"]
if not args:
return True
result = self.avrdude(*args, bitclock=bitclock)
text = result.stdout + result.stderr
return "verified" in text or "written" in text
# ------------------------------------------------------------ backup
def backup(self, directory: pathlib.Path, prefix: str = "") -> dict[str, bool]:
"""Capture every memory worth keeping, then prove it by a second read.
A backup nobody verified is a guess. Each memory is read twice and the
two reads compared; a mismatch is reported rather than quietly stored.
"""
directory = pathlib.Path(directory).resolve()
directory.mkdir(parents=True, exist_ok=True)
stem = prefix or self.d.part
status: dict[str, bool] = {}
for memory, fmt, extension in BACKUP_MEMORIES:
name = f"{stem}-{memory}.{extension}"
if not self.read_memory(memory, directory / name, fmt):
status[f"{memory}.{extension}"] = False
continue
if extension == "bin": # only the raw form is worth comparing byte-wise
again = directory / f".{name}.again"
self.read_memory(memory, again, fmt)
same = again.exists() and again.read_bytes() == (directory / name).read_bytes()
again.unlink(missing_ok=True)
status[f"{memory}.{extension}"] = same
else:
status[f"{memory}.{extension}"] = True
return status
# ------------------------------------------------------------ serial link
def pureboot(self, *args: str, reset_first: bool = True, baud: int | None = None,
autobaud: bool | None = None, timeout: int = 300,
bitclock: str | None = None) -> tuple[int, str]:
"""Reset, then knock immediately — see the module docstring.
Returns the host tool's exit status and its combined output, so a caller
can assert on what it printed as well as on whether it succeeded.
"""
if reset_first:
self.reset(bitclock=bitclock)
command = [sys.executable, str(self.d.pureboot), "--port", self.d.port,
"--baud", str(self.d.baud if baud is None else baud),
"--wait", str(self.d.wait)]
if self.d.autobaud if autobaud is None else autobaud:
command.append("--autobaud")
if self.d.one_wire:
command.append("--one-wire")
command += [str(a) for a in args]
try:
result = subprocess.run(command, capture_output=True, text=True, timeout=timeout)
except subprocess.TimeoutExpired as expired:
return 99, f"TIMEOUT after {timeout}s\n{expired.stdout or ''}{expired.stderr or ''}"
return result.returncode, (result.stdout or "") + (result.stderr or "")
def open_port(self, baud: int | None = None):
"""A port opened the way this deployment says to speak to the board.
Everything the rig runs as a *subprocess* gets its flags from
`pureboot()` above; anything that drives the protocol in-process has
to reach the same facts, and until this existed only the subprocess
path could. A shared line is the one where that gap is fatal rather
than untidy: the host reads back every byte it writes, so an
undiscarded echo answers the knock before the device does. Open
through here and a one-wire deployment cannot be silently driven as
a two-wire one.
"""
module = load_pureboot(self.d.pureboot)
port = module.Port(self.d.port, self.d.baud if baud is None else baud)
return module.OneWirePort(port) if self.d.one_wire else port
def capture(self, seconds: float = 2.0, baud: int | None = None) -> bytes:
"""Listen to whatever the board is saying, at an arbitrary rate.
Opening the port does not reset a board whose DTR is unwired, so this can
sample a running application repeatedly without disturbing it — which is
what makes the rate sweep below possible.
"""
module = load_pureboot(self.d.pureboot)
port = module.Port(self.d.port, self.d.baud if baud is None else baud)
try:
data = b""
deadline = time.monotonic() + seconds
while time.monotonic() < deadline:
chunk = port.read_available(0.2)
if chunk:
data += chunk
return data
finally:
try:
port.close()
except Exception:
pass
def measure_rate(rig: Rig, marker: bytes, built_baud: int, nominal_hz: int | None = None,
span_percent: float = 12.0, step_percent: float = 0.5,
seconds: float = 0.75) -> dict:
"""Find a transmitting board's true bit rate, using only the serial port.
The board must be emitting something recognisable at a *fixed* cycles-per-bit
— `test/pbapp.cpp` built with PUREBOOT_HEARTBEAT does. Since its bit timing is
a cycle count, its wire rate scales with its actual clock, so the host rates
at which `marker` still decodes bracket that rate; the centre of the band is
the answer, and with the clock the image was built for it gives the real one.
This is the measurement that turns "the loader is silent, so the wiring must
be wrong" into a number, and it needs no instrument beyond the adapter
already attached.
"""
steps = int(span_percent / step_percent)
clean: list[int] = []
samples: list[tuple[int, int, bool]] = []
for index in range(-steps, steps + 1):
baud = int(round(built_baud * (1 + index * step_percent / 100.0)))
if baud <= 0:
continue
data = rig.capture(seconds=seconds, baud=baud)
hit = marker in data
samples.append((baud, len(data), hit))
if hit:
clean.append(baud)
result: dict = {"samples": samples, "clean": clean, "built_baud": built_baud}
if clean:
low, high = min(clean), max(clean)
centre = (low + high) / 2.0
result |= {"low": low, "high": high, "centre": centre,
"half_width_percent": (high - low) / 2.0 / centre * 100.0,
"error_percent": (centre / built_baud - 1.0) * 100.0}
if nominal_hz:
result["measured_hz"] = nominal_hz * centre / built_baud
return result
# ------------------------------------------------------------------- command
def main(argv: list[str] | None = None) -> int:
parser = argparse.ArgumentParser(
description="pureboot hardware rig: ISP reset/flash beside the serial link")
Deployment.add_arguments(parser)
sub = parser.add_subparsers(dest="command", required=True)
sub.add_parser("signature", help="read the part signature over ISP")
sub.add_parser("reset", help="reset the part (an ISP access) and let it run")
sub.add_parser("fuses", help="read the fuse and lock bytes")
p = sub.add_parser("flash", help="program a hex image over ISP")
p.add_argument("image", type=pathlib.Path)
p.add_argument("--no-erase", action="store_true", help="do not chip-erase first")
p = sub.add_parser("backup", help="capture and verify every memory")
p.add_argument("directory", type=pathlib.Path)
p.add_argument("--prefix", default="", help="filename stem (default: the part name)")
p = sub.add_parser("rate", help="measure the board's true bit rate and clock")
p.add_argument("--marker", default="APP", help="text the board emits (default: APP)")
p.add_argument("--built-baud", type=int, required=True,
help="the baud the running image was built for")
p.add_argument("--nominal-hz", type=int, default=0,
help="the clock the image was built for, to report the real one")
p.add_argument("--span", type=float, default=12.0, help="sweep +-this many percent")
p.add_argument("--step", type=float, default=0.5, help="sweep step in percent")
p.add_argument("--verbose", action="store_true", help="print every step")
p = sub.add_parser("bitclock", help="a safe ISP bitclock for a clock in force")
p.add_argument("hz", type=int)
args = parser.parse_args(argv)
if args.command == "bitclock":
print(bitclock_for(args.hz))
return 0
rig = Rig(Deployment.from_args(args))
if args.command == "signature":
print(rig.signature())
elif args.command == "reset":
rig.reset()
print("reset")
elif args.command == "fuses":
for name, value in rig.read_fuses().items():
print(f"{name:<6} {value}")
elif args.command == "flash":
ok = rig.flash_hex(args.image, erase=not args.no_erase)
print(f"{args.image.name}: {'verified' if ok else 'FAILED'}")
return 0 if ok else 1
elif args.command == "backup":
status = rig.backup(args.directory, args.prefix)
for name, ok in status.items():
print(f" {'ok ' if ok else 'FAIL'} {name}")
missing = [n for n, ok in status.items() if not ok]
# Fuses a part does not have are expected misses, not failures.
fatal = [n for n in missing if not n.startswith(("efuse", "calibration"))]
print(f"\n{len(status) - len(missing)}/{len(status)} captured into {args.directory}")
return 1 if fatal else 0
elif args.command == "rate":
result = measure_rate(rig, args.marker.encode(), args.built_baud,
args.nominal_hz or None, args.span, args.step)
if args.verbose:
for baud, size, hit in result["samples"]:
print(f" {baud:7d} Bd {size:5d} B {'MARKER' if hit else ''}")
if not result["clean"]:
print(f"no capture contained {args.marker!r} at any rate — is the board "
f"transmitting, and on the pin this port is wired to?")
return 1
print(f"clean band {result['low']}..{result['high']} Bd")
print(f"centre {result['centre']:.0f} Bd "
f"(+-{result['half_width_percent']:.1f} %)")
print(f"vs built {result['built_baud']} Bd ({result['error_percent']:+.1f} %)")
if "measured_hz" in result:
print(f"true clock {result['measured_hz'] / 1e6:.3f} MHz")
return 0
if __name__ == "__main__":
try:
sys.exit(main())
except Error as error:
print(f"error: {error}", file=sys.stderr)
sys.exit(2)

187
tools/sizes.py Executable file
View File

@@ -0,0 +1,187 @@
#!/usr/bin/env python3
"""What the loader images actually measure, and whether the README still agrees.
The size matrix asserts every image fits its slot; it says nothing about the
numbers the README prints, and those drift. Every row of that table was eight
bytes stale once `startup::caller_page()` landed — common code, so every build
moved at once and no test noticed, because none of them was over budget.
Two questions, both answered from built trees:
sizes.py max the largest image per chip, and anything over budget
sizes.py check-readme the README's per-chip table against what is built
Nothing here knows a chip's geometry. The (image, budget) pairs come from each
build's own `CTestTestfile.cmake` — the same values the gate checks — so the
slot rules stay where they belong, in `pureboot/CMakeLists.txt`, and a chip
added or a budget changed needs no edit here. Only trees a configure preset
still owns are read: a stale directory keeps its last build, and a loader built
before a slot changed will happily report a size that was true once
(`tools/prune-build-trees.sh` in libavr removes them).
Sizes come from `avr-size`, and a target is only as current as its last build —
run the gate first if you want the table checked against today's source.
"""
from __future__ import annotations
import argparse
import pathlib
import re
import shutil
import subprocess
import sys
ROOT = pathlib.Path(__file__).resolve().parents[1]
# add_test(<name>.size ... -DELF=<path> ... -DLIMIT=<n> ...) — the gate's own
# pairing of an image with the budget it must fit.
# ctest writes the name as a bracket argument ([=[name.size]=]) and quotes the
# rest, so the name starts after the bracket and the path ends at the quote.
SIZE_TEST = re.compile(r'add_test\(\s*\[=\[(?P<name>[^\]]+?)\.size\]=\][^\n]*?'
r'-DELF=(?P<elf>[^"\s]+)[^\n]*?-DLIMIT=(?P<limit>\d+)')
def avr_size() -> str:
for env in (ROOT / "../../toolchain").resolve().glob("avr-gcc-*/bin/avr-size"):
if env.is_file():
return str(env)
found = shutil.which("avr-size")
if not found:
sys.exit("no avr-size found (build the toolchain, or put it on PATH)")
return found
def preset_dirs() -> list[pathlib.Path]:
"""Build trees a configure preset still owns, newest-listed first."""
listing = subprocess.run(["cmake", "--list-presets"], cwd=ROOT, capture_output=True, text=True)
names = re.findall(r'^\s*"(.+)"$', listing.stdout, re.MULTILINE)
if not names:
sys.exit("cmake --list-presets returned nothing — run from a configured checkout")
return [d for d in (ROOT / "build" / n for n in names) if (d / "CTestTestfile.cmake").is_file()]
def measure(paths: list[str], tool: str) -> dict[str, int]:
""".text per ELF, in one avr-size call per batch."""
sizes: dict[str, int] = {}
for start in range(0, len(paths), 400):
batch = [p for p in paths[start:start + 400] if pathlib.Path(p).is_file()]
if not batch:
continue
out = subprocess.run([tool, *batch], capture_output=True, text=True).stdout
for line in out.splitlines()[1:]:
fields = line.split()
if len(fields) >= 6 and fields[0].isdigit():
sizes[fields[5]] = int(fields[0])
return sizes
def collect() -> dict[str, list[tuple[str, int, int]]]:
"""chip -> [(target, text, limit)], from every owned build tree."""
tool = avr_size()
found: dict[str, list[tuple[str, str, int]]] = {}
for tree in preset_dirs():
chip = tree.name.split("-")[0]
for match in SIZE_TEST.finditer((tree / "CTestTestfile.cmake").read_text()):
found.setdefault(chip, []).append((match["name"], match["elf"], int(match["limit"])))
sizes = measure([elf for rows in found.values() for _, elf, _ in rows], tool)
# A chip's generated and reflect trees must answer with the same bytes
# (the identity invariant), so the same target measuring two sizes means
# a stale tree — or an identity breach. Either is a finding; picking one
# silently is how a gate reports another build's numbers as today's.
for chip, rows in found.items():
seen: dict[str, tuple[int, str]] = {}
for name, elf, _ in rows:
if elf not in sizes:
continue
if name in seen and seen[name][0] != sizes[elf]:
sys.exit(f"{chip} {name}: {seen[name][0]} B in {seen[name][1]} but "
f"{sizes[elf]} B in {elf} — a stale tree (rebuild or remove it) "
f"or a cross-mode identity breach")
seen.setdefault(name, (sizes[elf], elf))
measured = {
chip: sorted(((name, sizes[elf], limit) for name, elf, limit in rows if elf in sizes),
key=lambda row: -row[1])
for chip, rows in sorted(found.items())
}
# A configured-but-unbuilt preset registers its tests with no images behind
# them; it is not a chip with nothing to say, it is a chip not built yet.
return {chip: rows for chip, rows in measured.items() if rows}
def cmd_max(args) -> int:
measured = collect()
if not measured:
sys.exit("nothing built — configure and build a preset first")
over = []
print(f"{'chip':<13} {'largest image':<34} {'.text':>6} {'budget':>7} headroom")
for chip, rows in measured.items():
name, text, limit = rows[0]
flag = "OVER" if text > limit else f"{limit - text:>5} B"
print(f"{chip:<13} {name:<34} {text:>6} {limit:>7} {flag}")
over += [(chip, n, t, l) for n, t, l in rows if t > l]
total = sum(len(rows) for rows in measured.values())
print(f"\n{total} images across {len(measured)} chips")
if over:
print("\nOVER BUDGET:")
for chip, name, text, limit in over:
print(f" {chip} {name}: {text} > {limit}")
return 1
tightest = min(((chip, n, t, l) for chip, rows in measured.items() for n, t, l in rows),
key=lambda row: row[3] - row[2])
chip, name, text, limit = tightest
print(f"tightest fit: {chip} {name} — {text} of {limit}, {limit - text} B spare")
return 0
def cmd_check_readme(args) -> int:
"""The README's per-chip table, against the stock build and the worst
autobaud configuration (OSCCAL baked, plus the USART-pin release where
the chip has a USART; the one-wire fold of the same build is its twin
and competes for the same cell) — the config the Autobaud column
documents."""
readme = (ROOT / "pureboot" / "README.md").read_text()
measured = collect()
rows = re.findall(r"^\|\s*(AT\w+[^|]*?)\s*\|[^|]*\|[^|]*\|[^|]*\|\s*(\d+) B\s*\|\s*(\d+) B\s*\|$",
readme, re.MULTILINE)
if not rows:
sys.exit("no size table found in pureboot/README.md")
bad = skipped = 0
for chips, stock_doc, auto_doc in rows:
# "ATmega48, 48A, 48P, 48PA †" — the first name is the family's base.
chip = re.sub(r"[^a-z0-9]", "", chips.split(",")[0].strip().lower())
built = {name: text for name, text, _ in measured.get(chip, [])}
# The on-USART pair defines the column where the chip has a USART;
# the default-pin pair is the whole space elsewhere. Whichever twin
# measures larger is the number the cell must state.
candidates = [name for name in ("pureboot_autobaud_osccal_on_usart0",
"pureboot_1w_autobaud_osccal_on_usart0") if name in built]
if not candidates:
candidates = [name for name in ("pureboot_autobaud_osccal",
"pureboot_1w_autobaud_osccal") if name in built]
worst = max(candidates, key=lambda name: built[name], default="pureboot_autobaud_osccal")
for target, documented in (("pureboot", stock_doc), (worst, auto_doc)):
if target not in built:
skipped += 1
continue
if built[target] != int(documented):
print(f" {chip:<12} {target:<18} README says {documented} B, built is {built[target]} B")
bad += 1
if bad:
print(f"\n{bad} row(s) stale — update pureboot/README.md")
return 1
print(f"README size table matches every built image ({len(rows)} rows"
+ (f", {skipped} not built" if skipped else "") + ")")
return 0
def main() -> int:
parser = argparse.ArgumentParser(description=__doc__.splitlines()[0])
subs = parser.add_subparsers(dest="cmd", required=True)
subs.add_parser("max", help="largest image per chip, and anything over budget")
subs.add_parser("check-readme", help="the README's size table against what is built")
args = parser.parse_args()
return {"max": cmd_max, "check-readme": cmd_check_readme}[args.cmd](args)
if __name__ == "__main__":
raise SystemExit(main())

4
tsb/clock.hpp
View File

@@ -1,4 +0,0 @@
#pragma once
#define F_CPU 18'432'000
#include <util/delay.h>

1
tsb/flash

Submodule tsb/flash deleted from 6edb2e5a21

1
tsb/io

Submodule tsb/io deleted from 80de36ee7e

102
tsb/main.cpp
View File

@@ -1,102 +0,0 @@
#include "clock.hpp"
#include "uart/uart.hpp"
constexpr auto READ_FLASH_CMD = 'f';
constexpr auto WRITE_FLASH_CMD = 'F';
constexpr auto READ_EEPROM_CMD = 'e';
constexpr auto WRITE_EEPROM_CMD = 'E';
constexpr auto READ_USERDATA_CMD = 'c';
constexpr auto WRITE_USERDATA_CMD = 'C';
constexpr auto REQUEST_CMD = '?';
constexpr auto CONFIRM_CMD = '!';
constexpr auto AUTO_BAUDING_CMD = '@';
using uart_interface = uart::Hardware0<uart::Config<115200>, uart::Driven::BLOCKING>;
enum class State {
WAITING,
ACTIVE,
};
struct DeviceInfo {
char name[3] = {'T', 'S', 'B'};
uint8_t date[2] = {0x1a, 0x1f};
uint8_t status = 0xf0;
uint8_t signature[3] = {0x1e, 0x95, 0x0f};
uint8_t pageSize = 0x40;
uint16_t flashSize = 0x3ec0;
uint16_t eepromSize = 0x03ff;
};
struct UserData {
uint16_t jumpAddress = 0xAAAA;
uint8_t timeout = 0x21;
};
static inline void sendDeviceInfo()
{
uart::Uart<uart_interface> serial;
constexpr DeviceInfo deviceInfo;
constexpr UserData userData;
for (uint8_t i = 0; i < sizeof(deviceInfo); ++i) {
serial.txByte(*(reinterpret_cast<const uint8_t *>(&deviceInfo) + i));
}
for (uint8_t i = 0; i < sizeof(userData); ++i) {
serial.txByte(*(reinterpret_cast<const uint8_t *>(&userData) + i));
}
}
static uint8_t g_lastPage[128] = {};
static inline void sendUserData()
{
uart::Uart<uart_interface> serial;
for (uint8_t i = 0; i < sizeof(g_lastPage); ++i) {
serial.txByte(*(reinterpret_cast<const uint8_t *>(&g_lastPage) + i));
}
}
static inline void sendConfirm()
{
uart::Uart<uart_interface> serial;
serial.txByte(CONFIRM_CMD);
}
int main()
{
uart::Uart<uart_interface> serial;
serial.init();
State state = State::WAITING;
uint8_t receivedByte = 0;
uint8_t autoBaudingCounter = 0;
while (true) {
if (serial.rxByte(receivedByte)) {
if (state == State::WAITING) {
if (receivedByte == AUTO_BAUDING_CMD) {
++autoBaudingCounter;
}
if (autoBaudingCounter == 3) {
autoBaudingCounter = 0;
state = State::ACTIVE;
sendDeviceInfo();
}
} else if (state == State::ACTIVE) {
if (receivedByte == READ_USERDATA_CMD) {
sendUserData();
sendConfirm();
state = State::WAITING;
}
}
}
}
return 0;
}

263
tsb/tsb.cppproj
View File

@@ -1,263 +0,0 @@
<?xml version="1.0" encoding="utf-8"?>
<Project DefaultTargets="Build" xmlns="http://schemas.microsoft.com/developer/msbuild/2003" ToolsVersion="14.0">
<PropertyGroup>
<SchemaVersion>2.0</SchemaVersion>
<ProjectVersion>7.0</ProjectVersion>
<ToolchainName>com.Atmel.AVRGCC8.CPP</ToolchainName>
<ProjectGuid>dce6c7e3-ee26-4d79-826b-08594b9ad897</ProjectGuid>
<avrdevice>ATmega328P</avrdevice>
<avrdeviceseries>none</avrdeviceseries>
<OutputType>Executable</OutputType>
<Language>CPP</Language>
<OutputFileName>$(MSBuildProjectName)</OutputFileName>
<OutputFileExtension>.elf</OutputFileExtension>
<OutputDirectory>$(MSBuildProjectDirectory)\$(Configuration)</OutputDirectory>
<AssemblyName>tsb</AssemblyName>
<Name>tsb</Name>
<RootNamespace>tsb</RootNamespace>
<ToolchainFlavour>avr-g++-9.1.0</ToolchainFlavour>
<KeepTimersRunning>true</KeepTimersRunning>
<OverrideVtor>false</OverrideVtor>
<CacheFlash>true</CacheFlash>
<ProgFlashFromRam>true</ProgFlashFromRam>
<RamSnippetAddress>0x20000000</RamSnippetAddress>
<UncachedRange />
<preserveEEPROM>true</preserveEEPROM>
<OverrideVtorValue>exception_table</OverrideVtorValue>
<BootSegment>2</BootSegment>
<ResetRule>0</ResetRule>
<eraseonlaunchrule>0</eraseonlaunchrule>
<EraseKey />
<avrtool>
</avrtool>
<avrtoolserialnumber>J41800099437</avrtoolserialnumber>
<avrdeviceexpectedsignature>0x1E9705</avrdeviceexpectedsignature>
<com_atmel_avrdbg_tool_stk500>
<ToolOptions>
<InterfaceProperties>
<IspClock>125000</IspClock>
</InterfaceProperties>
<InterfaceName>ISP</InterfaceName>
</ToolOptions>
<ToolType>com.atmel.avrdbg.tool.stk500</ToolType>
<ToolNumber>
</ToolNumber>
<ToolName>STK500</ToolName>
</com_atmel_avrdbg_tool_stk500>
<avrtoolinterface>ISP</avrtoolinterface>
<avrtoolinterfaceclock>125000</avrtoolinterfaceclock>
<AsfFrameworkConfig>
<framework-data xmlns="">
<options />
<configurations />
<files />
<documentation help="" />
<offline-documentation help="" />
<dependencies>
<content-extension eid="atmel.asf" uuidref="Atmel.ASF" version="3.47.0" />
</dependencies>
</framework-data>
</AsfFrameworkConfig>
<com_atmel_avrdbg_tool_atmelice>
<ToolOptions>
<InterfaceProperties>
<IspClock>125000</IspClock>
</InterfaceProperties>
<InterfaceName>ISP</InterfaceName>
</ToolOptions>
<ToolType>com.atmel.avrdbg.tool.atmelice</ToolType>
<ToolNumber>J41800099437</ToolNumber>
<ToolName>Atmel-ICE</ToolName>
</com_atmel_avrdbg_tool_atmelice>
<custom>
<ToolOptions>
<InterfaceProperties>
<IspClock>125000</IspClock>
</InterfaceProperties>
<InterfaceName>
</InterfaceName>
</ToolOptions>
<ToolType>custom</ToolType>
<ToolNumber>
</ToolNumber>
<ToolName>Custom Programming Tool</ToolName>
</custom>
<com_atmel_avrdbg_tool_simulator>
<ToolOptions xmlns="">
<InterfaceProperties>
</InterfaceProperties>
<InterfaceName>
</InterfaceName>
</ToolOptions>
<ToolType xmlns="">com.atmel.avrdbg.tool.simulator</ToolType>
<ToolNumber xmlns="">
</ToolNumber>
<ToolName xmlns="">Simulator</ToolName>
</com_atmel_avrdbg_tool_simulator>
<AAFDebugger>
<AAFDebugFiles>
</AAFDebugFiles>
</AAFDebugger>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Release' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega1284p</avrgcc.common.Device>
<avrgcc.common.optimization.RelaxBranches>True</avrgcc.common.optimization.RelaxBranches>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcc.compiler.symbols.DefSymbols>
<ListValues>
<Value>NDEBUG</Value>
</ListValues>
</avrgcc.compiler.symbols.DefSymbols>
<avrgcc.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcc.compiler.directories.IncludePaths>
<avrgcc.compiler.optimization.level>Optimize for size (-Os)</avrgcc.compiler.optimization.level>
<avrgcc.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcc.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcc.compiler.warnings.AllWarnings>True</avrgcc.compiler.warnings.AllWarnings>
<avrgcc.compiler.warnings.ExtraWarnings>True</avrgcc.compiler.warnings.ExtraWarnings>
<avrgcc.compiler.warnings.Pedantic>True</avrgcc.compiler.warnings.Pedantic>
<avrgcc.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -std=c11</avrgcc.compiler.miscellaneous.OtherFlags>
<avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>NDEBUG</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize for size (-Os)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.warnings.Pedantic>True</avrgcccpp.compiler.warnings.Pedantic>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -Wextra -std=c++17</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.libraries.Libraries>
<ListValues>
<Value>libm</Value>
</ListValues>
</avrgcccpp.linker.libraries.Libraries>
<avrgcccpp.assembler.general.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.assembler.general.IncludePaths>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<PropertyGroup Condition=" '$(Configuration)' == 'Debug' ">
<ToolchainSettings>
<AvrGccCpp>
<avrgcc.common.Device>-mmcu=atmega1284p</avrgcc.common.Device>
<avrgcc.common.optimization.RelaxBranches>True</avrgcc.common.optimization.RelaxBranches>
<avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
<avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
<avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
<avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
<avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
<avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcc.compiler.symbols.DefSymbols>
<ListValues>
<Value>DEBUG</Value>
</ListValues>
</avrgcc.compiler.symbols.DefSymbols>
<avrgcc.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcc.compiler.directories.IncludePaths>
<avrgcc.compiler.optimization.level>Optimize (-O1)</avrgcc.compiler.optimization.level>
<avrgcc.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcc.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcc.compiler.optimization.DebugLevel>Maximum (-g3)</avrgcc.compiler.optimization.DebugLevel>
<avrgcc.compiler.warnings.AllWarnings>True</avrgcc.compiler.warnings.AllWarnings>
<avrgcc.compiler.warnings.ExtraWarnings>True</avrgcc.compiler.warnings.ExtraWarnings>
<avrgcc.compiler.warnings.Pedantic>True</avrgcc.compiler.warnings.Pedantic>
<avrgcc.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -std=c11</avrgcc.compiler.miscellaneous.OtherFlags>
<avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultCharTypeUnsigned>
<avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcccpp.compiler.general.ChangeDefaultBitFieldUnsigned>
<avrgcccpp.compiler.symbols.DefSymbols>
<ListValues>
<Value>DEBUG</Value>
</ListValues>
</avrgcccpp.compiler.symbols.DefSymbols>
<avrgcccpp.compiler.directories.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.compiler.directories.IncludePaths>
<avrgcccpp.compiler.optimization.level>Optimize (-O1)</avrgcccpp.compiler.optimization.level>
<avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcccpp.compiler.optimization.AllocateBytesNeededForEnum>
<avrgcccpp.compiler.optimization.DebugLevel>Maximum (-g3)</avrgcccpp.compiler.optimization.DebugLevel>
<avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
<avrgcccpp.compiler.warnings.Pedantic>True</avrgcccpp.compiler.warnings.Pedantic>
<avrgcccpp.compiler.miscellaneous.OtherFlags>-fno-threadsafe-statics -Wextra -std=c++17</avrgcccpp.compiler.miscellaneous.OtherFlags>
<avrgcccpp.linker.libraries.Libraries>
<ListValues>
<Value>libm</Value>
</ListValues>
</avrgcccpp.linker.libraries.Libraries>
<avrgcccpp.assembler.general.IncludePaths>
<ListValues>
<Value>%24(PackRepoDir)\Atmel\ATmega_DFP\1.4.346\include</Value>
</ListValues>
</avrgcccpp.assembler.general.IncludePaths>
<avrgcccpp.assembler.debugging.DebugLevel>Default (-Wa,-g)</avrgcccpp.assembler.debugging.DebugLevel>
</AvrGccCpp>
</ToolchainSettings>
</PropertyGroup>
<ItemGroup>
<Compile Include="clock.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="flash\flash.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="io\io.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="main.cpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="type\type.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\config.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\hardware.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\hardware0.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\hardware1.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\software.hpp">
<SubType>compile</SubType>
</Compile>
<Compile Include="uart\uart.hpp">
<SubType>compile</SubType>
</Compile>
</ItemGroup>
<ItemGroup>
<Folder Include="flash" />
<Folder Include="io" />
<Folder Include="uart" />
<Folder Include="type" />
</ItemGroup>
<Import Project="$(AVRSTUDIO_EXE_PATH)\\Vs\\Compiler.targets" />
</Project>

386
tsb/tsb_asm.cpp Normal file
View File

@@ -0,0 +1,386 @@
// TinySafeBoot on libavr — tier 3: full feature parity in the 512-byte boot
// section, in C++ except where the C ABI itself is the cost.
//
// The complete TinySafeBoot feature set — watchdog-reset bail, one-wire
// half-duplex UART, a config-page activation timeout, the password gate,
// emergency erase, and config/flash/EEPROM read-write — at 510 bytes in the
// 512-byte BOOTSZ=11 section the hand-written oracle occupies (500 B). This tier used to be one
// monolithic inline-asm routine; it is now the tricks tier's C++ (same
// register protocol, same structure — see tsb_tricks.cpp, including the
// global-register miscompile rules) with exactly two routines kept in
// assembly, the two whose remaining cost *is* the calling convention:
//
// rx the bounded receive: C++ must re-floor the timeout window on every
// call (the global-register-store miscompile) and split it across
// call-saved registers; the asm keeps the oracle's X-register nested
// countdown.
// store the page-store loop: C++ cannot hold the receive byte pair and the
// walked Z pointer across the rx calls without call-saved staging
// (push/pop + a Y→Z copy per word); the asm calls rx knowing exactly
// which registers it touches and walks Z live across the whole page.
//
// Everything else — bring-up, activation, password gate, emergency erase,
// dispatch, every SPM/EEPROM/flash primitive, every geometry/baud/info
// constant — is C++ on libavr, and the two asm routines splice into the same
// global-register protocol the C++ uses (g_addr in Y, g_cnt in r16, g_window
// in r7, g_receiving in r6), so calls cross the boundary with no marshalling.
//
// The wire protocol is strict request/response, which is what makes the shared
// line safe: the device drives it only between a received command and its
// reply, and releases it (RXEN0 only) whenever it waits.
#include <libavr/libavr.hpp>
#include <avr/io.h> // SP / RAMEND for the crt-free boot entry, SFR addresses for the asm routines
using namespace avr::literals;
namespace spm = avr::spm;
namespace ee = avr::eeprom;
namespace hw = avr::hw;
namespace tsb {
namespace {
// The loader is purely polled — it never enables interrupts — so every SPM and
// EEPROM lock folds to nothing under this posture.
constexpr auto off = avr::irq::guard_policy::unused;
constexpr std::uint8_t confirm = '!';
constexpr std::uint8_t request = '?';
constexpr std::uint8_t knock = '@';
// Boot geometry for the 512 B boot section (BOOTSZ=11); the page size and the
// flash/EEPROM extents are the chip database's to know. app_end is the config
// page (TSB's LASTPAGE), one page below the boot section.
constexpr std::uint16_t page = spm::page_bytes;
constexpr std::uint16_t boot_bytes = 512;
constexpr std::uint16_t app_end = spm::flash_bytes - boot_bytes - page;
constexpr std::uint16_t eeprom_end = avr::hw::db.mem.eeprom_size - 1;
// Lockout-proof floor for the activation window (the oracle's F_CPU/1MHz).
constexpr std::uint8_t act_min = 16;
// Post-activation window: the host gets seconds, not milliseconds, mid-session.
constexpr std::uint8_t comm_window = 200;
constexpr std::uint16_t build_date = 26 * 512 + 7 * 32 + 20;
// Fixed 115200 8N1; the library solves UBRR + U2X from clock and baud.
constexpr auto baud = avr::uart::solve_baud(16_MHz, 115200_Bd);
// The 16-byte device-info block, streamed out on activation.
// clang-format off
[[gnu::progmem]] constexpr std::uint8_t info[16] = {
'T', 'S', 'B',
build_date & 0xFF, build_date >> 8,
0xF3, // status: native-UART fixed-baud lineage
0x1E, 0x95, 0x0F, // ATmega328P signature
page / 2, // page size in words
(app_end / 2) & 0xFF, (app_end / 2) >> 8,
eeprom_end & 0xFF, eeprom_end >> 8,
0xAA, 0xAA,
};
// clang-format on
register std::uint16_t g_addr asm("r28");
register std::uint8_t g_cnt asm("r16");
register std::uint8_t g_window asm("r7");
register std::uint8_t g_receiving asm("r6");
const std::uint8_t *flash_ptr(std::uint16_t addr)
{
return reinterpret_cast<const std::uint8_t *>(addr);
}
// Bounded byte receive (asm 1 of 2): release the one-wire line on a direction
// change, poll RXC0 under the oracle's nested X-register countdown seeded from
// g_window (floored against lockout), byte or 0-on-silence in r24. Z survives
// — the property the store's word loop rides on.
[[gnu::noinline, gnu::noclone]] std::uint8_t rx()
{
std::uint8_t byte;
asm volatile(" tst %[dir] \n\t" // already receiving? keep the line released
" brne 1f \n\t"
" ldi %[b], 0x10 \n\t" // RXEN0 alone: release the line and listen
" sts %[ucsr0b], %[b] \n\t"
" ser %[b] \n\t"
" mov %[dir], %[b] \n\t"
"1: mov r27, %[to] \n\t" // outer countdown high byte = window
" ori r27, %[actmin] \n\t" // lockout-proof floor
" clr r26 \n\t"
"2: ser %[b] \n\t"
"3: lds %[b], %[ucsr0a] \n\t"
" sbrc %[b], 7 \n\t" // RXC0
" rjmp 4f \n\t"
" dec %[b] \n\t"
" brne 3b \n\t"
" sbiw r26, 1 \n\t"
" brcc 2b \n\t"
" clr %[b] \n\t" // silence → 0, which no compare accepts
" rjmp 5f \n\t"
"4: lds %[b], %[udr0] \n\t"
"5: \n\t"
: [b] "=&d"(byte), [dir] "+r"(g_receiving)
: [to] "r"(g_window), [actmin] "M"(act_min), [ucsr0a] "n"(_SFR_MEM_ADDR(UCSR0A)),
[ucsr0b] "n"(_SFR_MEM_ADDR(UCSR0B)), [udr0] "n"(_SFR_MEM_ADDR(UDR0))
: "r26", "r27", "cc");
return byte;
}
// One-wire transmit: take the line (TXEN0 alone) on a direction change with a
// turn-around guard, put the byte out, hold the line until the whole frame is
// out (TXC0, not UDRE0), W1C TXC0 by storing the sampled status back (keeps
// U2X0). Plain C++ — it compiles *smaller* than the oracle's routine.
[[gnu::noinline, gnu::noclone]] void tx(std::uint8_t byte)
{
if (g_receiving) {
g_receiving = 0;
hw::ucsr0b::write(hw::ucsr0b::txen0(1));
for (std::uint8_t guard = 46; guard; --guard)
;
}
hw::udr0::write(byte);
std::uint8_t status;
do {
status = hw::ucsr0a::read();
} while (!(status & hw::ucsr0a::txc0(1).value));
hw::ucsr0a::write(status);
}
// '?', then hand back the host's reply for the callers' one-byte compare.
[[gnu::noinline, gnu::noclone]] std::uint8_t rcnf()
{
tx(request);
return rx();
}
// One flash byte ← [g_addr++] (the advance right before ret — the
// global-register rule, see tsb_tricks.cpp).
[[gnu::noinline, gnu::noclone]] std::uint8_t sflash()
{
std::uint8_t byte = avr::flash_load(flash_ptr(g_addr));
++g_addr;
return byte;
}
// One EEPROM byte ← [g_addr++].
[[gnu::noinline, gnu::noclone]] std::uint8_t eerd()
{
std::uint8_t byte = ee::read(g_addr);
++g_addr;
return byte;
}
// One EEPROM byte → [g_addr++].
[[gnu::noinline, gnu::noclone]] void eewr(std::uint8_t byte)
{
ee::write<off>(g_addr, byte);
++g_addr;
}
// Stream g_cnt flash bytes from g_addr to the host.
[[gnu::noinline, gnu::noclone]] void sendf()
{
do {
tx(sflash());
} while (--g_cnt);
}
// Wait out a running SPM op, then re-open the RWW section — after every page
// op and before handing over, as the oracle does.
[[gnu::noinline, gnu::noclone]] void settle()
{
spm::wait();
spm::rww_enable<off>();
}
extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --defsym=tsb_app=0
[[noreturn]] void appjump()
{
settle();
tsb_app();
}
// Step g_addr one page down and erase that page (the decrement lives here —
// the global-register rule).
[[gnu::noinline, gnu::noclone]] void erase_below()
{
g_addr -= page;
spm::erase_page<off>(g_addr);
settle();
}
// Erase the whole application, top-down like the oracle: the loop bound is a
// compare with zero, and g_addr = 0 is handed back for free.
[[gnu::noinline, gnu::noclone]] void erase_application()
{
g_addr = app_end;
do {
erase_below();
} while (g_addr != 0);
}
// Stream one host page into the erased flash page at g_addr (asm 2 of 2): the
// word pair stages in r0:r1 straight from rx (whose register set is known —
// the cross-call liveness C++ cannot express), Z walks the page and PGWRT
// programs it. g_addr is left at the next page base.
[[gnu::noinline, gnu::noclone]] void store_flash()
{
asm volatile(" movw r30, r28 \n\t" // Z = page base; rx leaves Z live
" ldi r20, %[words] \n\t"
"1: rcall %x[rx] \n\t"
" mov r0, r24 \n\t" // word low byte
" rcall %x[rx] \n\t"
" mov r1, r24 \n\t" // word high byte
" ldi r24, 0x01 \n\t" // SPMEN: buffer the word at Z
" out %[spmcsr], r24 \n\t"
" spm \n\t"
" clr r1 \n\t"
" adiw r30, 2 \n\t"
" dec r20 \n\t"
" brne 1b \n\t"
" movw %[base], r30 \n\t" // g_addr = the next page base
" subi r30, %[pagelo] \n\t" // Z back to this page's base
" sbci r31, %[pagehi] \n\t"
" ldi r24, 0x05 \n\t" // PGWRT | SPMEN: program the page
" out %[spmcsr], r24 \n\t"
" spm \n\t"
: [base] "+r"(g_addr)
: [rx] "i"(&rx), [spmcsr] "I"(_SFR_IO_ADDR(SPMCSR)), [words] "M"(page / 2), [pagelo] "M"(page & 0xff),
[pagehi] "M"(page >> 8)
: "r0", "r1", "r20", "r24", "r26", "r27", "r30", "r31", "cc", "memory");
settle();
}
[[noreturn, gnu::noinline]] void run()
{
// A watchdog reset hands straight back to the application, as the
// reference loader does, rather than re-entering the bootloader.
if (hw::mcusr::wdrf.test())
appjump();
// Lean bring-up from reset state: UCSR0C already reads 8N1, UBRR0H reads
// 0, and rx()/tx() raise RXEN0/TXEN0 on first use — only the divisor low
// byte and U2X0 need a store. The library still does the datasheet work.
static_assert(baud.u2x && baud.ubrr < 256, "lean bring-up writes UBRR0L only, with U2X0");
hw::ubrr0::write(static_cast<std::uint8_t>(baud.ubrr));
hw::ucsr0a::write(hw::ucsr0a::u2x0(1));
// General-purpose registers are undefined at power-on (no crt zeroes them);
// the direction latch must start "not receiving" so the first rx() enables
// the receiver. The reference loader clears its shadow register for the
// same reason.
g_receiving = 0;
// Activation: 3×'@', each inside the config page's timeout window (rx
// floors it so a corrupt page cannot lock the loader out); anything else —
// including silence — hands over.
g_window = avr::flash_load(flash_ptr(app_end + 2));
for (std::uint8_t k = 3; k; --k)
if (rx() != knock)
appjump();
g_window = comm_window;
// Password gate (config page from app_end+3, 0xff-terminated; a blank
// page is no password). A wrong byte blanks the comparison and drains the
// line forever, so a wrong password can never fall through; a 0 requests
// emergency erase behind two confirms. On pass the info block goes out;
// the emergency path skips it and drops into the command loop.
g_addr = app_end + 3;
std::uint8_t mask = 0xff;
for (;;) {
std::uint8_t expected = avr::flash_load(flash_ptr(g_addr)) & mask;
++g_addr;
if (expected == 0xff) {
g_addr = reinterpret_cast<std::uint16_t>(&info[0]);
g_cnt = sizeof(info);
sendf();
break;
}
std::uint8_t got = rx();
if (got == 0) {
if (mask == 0)
continue;
if (rcnf() != confirm || rcnf() != confirm)
appjump();
erase_application(); // leaves g_addr = 0 for the EEPROM walk
do {
eewr(0xff);
} while (g_addr <= eeprom_end);
g_addr = app_end + page;
erase_below();
break;
}
if (got != expected)
mask = 0;
}
for (;;) {
tx(confirm); // Mainloop ready
g_addr = 0;
switch (rx()) {
case 'f': // read application flash, one page per host '!'
for (;;) {
if (rx() != confirm)
break;
g_cnt = page;
sendf();
if (g_addr >= app_end)
break;
}
break;
case 'F': // erase the application, then take pages behind '?'
erase_application(); // leaves g_addr = 0, the write start
while (rcnf() == confirm)
store_flash();
break;
case 'e': // read EEPROM, one page per host '!', until the host stops
for (;;) {
if (rx() != confirm)
break;
g_cnt = page;
do {
tx(eerd());
} while (--g_cnt);
}
break;
case 'E': // take EEPROM pages behind '?'
while (rcnf() == confirm) {
g_cnt = page;
do {
eewr(rx());
} while (--g_cnt);
}
break;
case 'c': // read the config page
read_config:
g_addr = app_end;
g_cnt = page;
sendf();
break;
case 'C': // replace the config page, then echo it back to verify
if (rcnf() != confirm)
break;
g_addr = app_end + page;
erase_below(); // leaves g_addr = app_end, the store target
store_flash();
goto read_config;
default: // 'q' or any other byte runs the application
appjump();
}
}
}
} // namespace
} // namespace tsb
// Reset lands here: BOOTRST vectors to the boot section base and .vectors is
// laid first, so this is the first instruction executed. No crt ran, so set
// the stack pointer before anything is called.
extern "C" [[gnu::naked, gnu::used, gnu::section(".vectors")]] void __boot_entry()
{
SP = RAMEND;
// The one line of crt this loader needs: compiled code assumes
// __zero_reg__ (r1) is 0, and power-on registers are undefined.
asm volatile("clr __zero_reg__");
tsb::run();
}

302
tsb/tsb_policy.cpp Normal file
View File

@@ -0,0 +1,302 @@
// TinySafeBoot on libavr — the policy floor: pureboot's rules, measured.
//
// The full TinySafeBoot feature set — watchdog bail, one-wire half-duplex,
// config-page activation timeout, password gate, emergency erase, and
// config/flash/EEPROM read-write — under philosophy #5 exactly as pureboot
// obeys it: no assembly, no register variables; code, attributes, and flags
// only. Every lesson pureboot's development produced is applied — the
// library's half-duplex serial and startup entry, lean bring-up from reset
// state, one merged send loop over both memories, oracle-shaped loop bounds,
// locals threaded through noinline primitives, pureboot's codegen flags —
// and the result is 638 bytes: 198 below the idiomatic tier, and 126 above
// the 512 B boot section the tricks/asm tiers reach with the banned
// mechanisms (526/510). This tier exists to keep that number an artifact
// rather than a claim: the gap to 512 is the rent of policy-clean C++ —
// helpers that hold a cursor across rx()/tx() pay push/pop and argument
// threading where a global-register protocol pays nothing, and both
// control-flow merges tried (a parametrized paged session, a merged store
// loop) measured larger than the split cases they replaced. TSB's wire fixes
// the per-command loop shapes on the device, so pureboot 5's one-transfer-
// loop collapse has no purchase here.
//
// The wire protocol is strict request/response, which is what makes the
// shared line safe: the device drives it only between a received command and
// its reply, and releases it (the library's half-duplex choreography)
// whenever it waits.
#include <libavr/libavr.hpp>
using namespace avr::literals;
namespace spm = avr::spm;
namespace ee = avr::eeprom;
using dev = avr::device<{.clock = 16_MHz}>;
// One-wire: RX and TX share the line, exactly as the native-UART TSB expects.
using serial_t = dev::uart0<{.baud = 115200_Bd, .max_baud_error = 3_pct, .half_duplex = true}>;
inline constexpr serial_t serial{};
namespace tsb {
namespace {
// The loader is purely polled — it never enables interrupts — so every SPM and
// EEPROM lock folds to nothing under this posture.
constexpr auto off = avr::irq::guard_policy::unused;
// The handshake bytes, identical across every TSB host.
constexpr std::uint8_t confirm = '!';
constexpr std::uint8_t request = '?';
constexpr std::uint8_t knock = '@';
// Boot geometry for the 1 KB boot section (BOOTSZ=10); the page size and the
// flash/EEPROM extents are the chip database's to know. app_end is the config
// page (TSB's LASTPAGE), one page below the boot section.
constexpr std::uint16_t page = spm::page_bytes;
constexpr std::uint16_t boot_bytes = 1024;
constexpr std::uint16_t app_end = spm::flash_bytes - boot_bytes - page;
constexpr std::uint16_t eeprom_end = avr::hw::db.mem.eeprom_size - 1;
// Lockout-proof floor for the activation window (the oracle's F_CPU/1MHz).
constexpr std::uint8_t act_min = 16;
// Post-activation window: the host gets seconds, not milliseconds, mid-session.
constexpr std::uint8_t comm_window = 200;
// Firmware version stamp: YY*512 + MM*32 + DD, the encoding the host decodes.
constexpr std::uint16_t build_date = 26 * 512 + 7 * 32 + 27;
// The 16-byte device-info block, streamed out on activation.
// clang-format off
[[gnu::progmem]] constexpr std::uint8_t info[16] = {
'T', 'S', 'B',
build_date & 0xFF, build_date >> 8,
0xF3, // status: native-UART fixed-baud lineage
avr::hw::db.signature[0], avr::hw::db.signature[1], avr::hw::db.signature[2],
page / 2, // page size in words
(app_end / 2) & 0xFF, (app_end / 2) >> 8, // app-flash boundary, words
eeprom_end & 0xFF, eeprom_end >> 8,
0xAA, 0xAA, // ATmega processor-type marker (bytes 14 == 15)
};
// clang-format on
// The receive window, pre-floored where it is set. In .noinit: there is no
// crt to clear a .bss image, and run() stores it before the first receive.
[[gnu::section(".noinit")]] std::uint8_t window;
const std::uint8_t *flash_ptr(std::uint16_t addr)
{
return reinterpret_cast<const std::uint8_t *>(addr);
}
// Bounded byte receive: poll under nested countdowns, 0 on silence. The 0
// then falls through every compare — not a knock, not a confirm, not a
// command — so a silent host unwinds the loader to the application from
// anywhere, and a mid-session cable pull cannot wedge it. The line release on
// a direction change is the serial backend's.
[[gnu::noinline]] std::uint8_t rx()
{
std::uint16_t outer = static_cast<std::uint16_t>(window) << 8;
do {
std::uint8_t fine = 0;
do {
if (auto byte = serial.read())
return *byte;
} while (--fine);
} while (--outer);
return 0;
}
// One-wire transmit: the backend takes the line with a turn-around guard and
// holds it until the whole frame is out.
[[gnu::noinline]] void tx(std::uint8_t byte)
{
serial.write(byte);
}
// '?', then hand back the host's reply for the callers' one-byte compare.
[[gnu::noinline]] std::uint8_t rcnf()
{
tx(request);
return rx();
}
// The one send loop: the info block, the config page, application flash and
// EEPROM pages all stream through here.
[[gnu::noinline]] void send_block(bool eep, std::uint16_t at, std::uint8_t count)
{
do {
tx(eep ? ee::read(at) : avr::flash_load(flash_ptr(at)));
++at;
} while (--count);
}
// One EEPROM byte in — shared by the emergency wipe and the 'E' stream.
[[gnu::noinline]] void eeput(std::uint16_t at, std::uint8_t value)
{
ee::write<off>(at, value);
}
// Wait out a running SPM op, then re-open the RWW section — after every page
// op and before handing over, as the oracle does.
[[gnu::noinline]] void settle()
{
spm::wait();
spm::rww_enable<off>();
}
// One host page straight into the erased flash page at `at` — through the SPM
// word buffer (low byte then high), no SRAM staging — then committed. `at`
// names a page base, so the cursor's low byte reaching the boundary ends the
// walk.
[[gnu::noinline]] void store_flash_page(std::uint16_t at)
{
do {
std::uint8_t low = rx();
std::uint8_t high = rx();
spm::fill<off>(at, std::bit_cast<std::uint16_t>(std::array{low, high}));
at += 2;
} while (static_cast<std::uint8_t>(at) & (page - 1));
spm::write_page<off>(at - page);
settle();
}
extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --defsym=tsb_app=0
[[noreturn]] void appjump()
{
settle();
tsb_app();
}
// Step one page down and erase it — the erase shared by the whole-app walk,
// the config rewrite and the emergency wipe; hands the stepped address back.
[[gnu::noinline]] std::uint16_t erase_below(std::uint16_t at)
{
at -= page;
spm::erase_page<off>(at);
settle();
return at;
}
// Erase the whole application, top-down like the oracle: the loop bound is a
// compare with zero, and the returned 0 is the address every caller wants
// next.
[[gnu::noinline]] std::uint16_t erase_application()
{
std::uint16_t at = app_end;
do {
at = erase_below(at);
} while (at != 0);
return at;
}
[[noreturn]] void run()
{
// A watchdog reset hands straight back to the application, as the
// reference loader does, rather than re-entering the bootloader.
if (avr::hw::mcusr::wdrf.test())
appjump();
// Lean bring-up from reset state: UCSR0C already reads 8N1, UBRR0H reads
// 0, and the half-duplex write()/read() raise TXEN0/RXEN0 on first use —
// only the divisor low byte and U2X0 need a store. The solver still does
// the datasheet work; the asserts pin the reset-state assumptions.
{
constexpr auto sol = avr::uart::solve_baud(dev::clock, 115200_Bd);
static_assert(sol.u2x && sol.ubrr < 256, "lean bring-up writes UBRR0L only, with U2X0");
avr::hw::ubrr0::write(static_cast<std::uint8_t>(sol.ubrr));
avr::hw::ucsr0a::write(avr::hw::ucsr0a::u2x0(1));
}
// Activation: 3×'@', each inside the config page's timeout window
// (floored so a corrupt page cannot lock the loader out); anything else —
// including silence — hands over.
window = avr::flash_load(flash_ptr(app_end + 2)) | act_min;
for (std::uint8_t k = 3; k; --k)
if (rx() != knock)
appjump();
window = comm_window;
// Password gate (config page from app_end+3, 0xff-terminated; a blank
// page is no password). A wrong byte blanks the comparison and drains the
// line forever, so a wrong password can never fall through; a 0 requests
// emergency erase behind two confirms. On pass the info block goes out;
// the emergency path skips it and drops into the command loop.
std::uint16_t at = app_end + 3;
std::uint8_t mask = 0xff;
for (;;) {
std::uint8_t expected = avr::flash_load(flash_ptr(at)) & mask;
++at;
if (expected == 0xff) {
send_block(false, reinterpret_cast<std::uint16_t>(&info[0]), sizeof info);
break;
}
std::uint8_t got = rx();
if (got == 0) {
if (mask == 0)
continue;
if (rcnf() != confirm || rcnf() != confirm)
appjump();
std::uint16_t a = erase_application();
do {
eeput(a, 0xff);
} while (++a <= eeprom_end);
erase_below(app_end + page);
break;
}
if (got != expected)
mask = 0;
}
for (;;) {
tx(confirm); // Mainloop ready
const std::uint8_t command = rx();
switch (command) {
case 'f': // read application flash, one page per host '!'
for (std::uint16_t a = 0; a < app_end; a += page) {
if (rx() != confirm)
break;
send_block(false, a, page);
}
break;
case 'e': // read EEPROM, one page per host '!', until the host stops
for (std::uint16_t a = 0;; a += page) {
if (rx() != confirm)
break;
send_block(true, a, page);
}
break;
case 'F': { // erase the application, then take pages behind '?'
std::uint16_t a = erase_application();
for (; rcnf() == confirm; a += page)
store_flash_page(a);
break;
}
case 'E': // take EEPROM pages behind '?', each write host-paced
for (std::uint16_t a = 0; rcnf() == confirm;) {
std::uint8_t count = page;
do {
eeput(a, rx());
++a;
} while (--count);
}
break;
case 'c': // read the config page
read_config:
send_block(false, app_end, page);
break;
case 'C': // replace the config page, then echo it back to verify
if (rcnf() != confirm)
break;
store_flash_page(erase_below(app_end + page));
goto read_config;
default: // 'q' or any other byte runs the application
appjump();
}
}
}
} // namespace
} // namespace tsb
// Reset lands at the boot section base (BOOTRST): the entry stub in .vectors
// is laid first and does the one line of crt a crt-less image needs.
template struct avr::startup::entry<tsb::run>;

308
tsb/tsb_pure.cpp Normal file
View File

@@ -0,0 +1,308 @@
// TinySafeBoot on libavr — tier 1: pure, idiomatic C++.
//
// A serial flash bootloader for the ATmega328P boot section, reimplementing the
// TinySafeBoot native-UART fixed-baud protocol on libavr with the full feature
// set of the hand-written oracle: a watchdog-reset bail, one-wire half-duplex,
// a config-page activation timeout, the password gate, emergency erase, and
// config/flash/EEPROM read-write. This variant is written for clarity —
// well-factored functions, no compiler-specific size hacks, no inline assembly.
// The one-wire wiring, the flash-resident info block and every SPM/EEPROM lock
// are libavr's to handle; the only attribute is the naked reset entry that
// stands in for the absent C runtime.
#include <libavr/libavr.hpp>
#include <avr/io.h> // SP / RAMEND for the crt-free boot entry
using namespace avr::literals;
namespace spm = avr::spm;
namespace ee = avr::eeprom;
using dev = avr::device<{.clock = 16_MHz}>;
// One-wire: RX and TX share the line, exactly as the native-UART TSB expects.
using serial_t = dev::uart0<{.baud = 115200_Bd, .max_baud_error = 3_pct, .half_duplex = true}>;
inline constexpr serial_t serial{};
namespace tsb {
namespace {
// The loader is purely polled — it never enables interrupts — so every SPM and
// EEPROM lock folds to nothing under this posture.
constexpr auto off = avr::irq::guard_policy::unused;
// The handshake bytes, identical across every TSB host.
constexpr std::uint8_t confirm = '!';
constexpr std::uint8_t request = '?';
constexpr std::uint8_t knock = '@';
// Boot geometry for the 1 KB boot section (BOOTSZ=10). The page size and the
// flash/EEPROM extents are the chip database's to know. app_end is the config
// page (the LASTPAGE holding the app-jump vector, activation timeout and
// password), one page below the boot section.
constexpr std::uint16_t page = spm::page_bytes;
constexpr std::uint16_t boot_bytes = 1024;
constexpr std::uint16_t app_end = spm::flash_bytes - boot_bytes - page;
constexpr std::uint16_t eeprom_end = avr::hw::db.mem.eeprom_size - 1;
// Firmware version stamp: YY*512 + MM*32 + DD, the encoding the host decodes.
constexpr std::uint16_t build_date = 26 * 512 + 7 * 32 + 20;
// The 16-byte device-info block the host reads on activation. A flash_table
// keeps it in progmem with no .data image (there is no crt to copy one).
// clang-format off
inline constexpr std::array<std::uint8_t, 16> info_data = {
'T', 'S', 'B',
build_date & 0xFF, build_date >> 8,
0xF3, // status byte (native-UART fixed-baud lineage)
0x1E, 0x95, 0x0F, // ATmega328P signature
page / 2, // page size in words
(app_end / 2) & 0xFF, (app_end / 2) >> 8, // app-flash boundary, words
eeprom_end & 0xFF, eeprom_end >> 8,
0xAA, 0xAA, // ATmega processor-type marker (bytes 14 == 15)
};
// clang-format on
using info = avr::flash_table<info_data>;
// Blocking byte read/write over the one-wire line: read() releases the line to
// the receiver, write() takes it and holds it until the frame is out.
std::uint8_t rx()
{
return serial.read_blocking();
}
void tx(std::uint8_t byte)
{
serial.write(byte);
}
const std::uint8_t *flash_ptr(std::uint16_t addr)
{
return reinterpret_cast<const std::uint8_t *>(addr);
}
// Stream `count` bytes to the host, from flash (LPM) or from EEPROM.
void send_flash(std::uint16_t addr, std::uint8_t count)
{
while (count--)
tx(avr::flash_load(flash_ptr(addr++)));
}
void send_eeprom(std::uint16_t addr, std::uint8_t count)
{
while (count--)
tx(ee::read(addr++));
}
// Prompt the host with '?' and report whether it answered '!'.
bool request_confirm()
{
tx(request);
return rx() == confirm;
}
// Stream one page from the host straight into the already-erased flash page at
// `addr`, filling the SPM word buffer low byte then high — no SRAM staging, so
// receiving and programming are the same loop.
void store_flash_page(std::uint16_t addr)
{
for (std::uint16_t i = 0; i < page; i += 2) {
std::uint8_t lo = rx();
std::uint8_t hi = rx();
spm::fill<off>(addr + i, static_cast<std::uint16_t>(lo | (hi << 8)));
}
spm::write_page<off>(addr);
spm::wait();
}
// Stream one page from the host straight into EEPROM, byte by byte.
void store_eeprom_page(std::uint16_t addr)
{
for (std::uint16_t i = 0; i < page; ++i)
ee::write<off>(addr + i, rx());
}
// Erase one flash page and wait it out — the erase step shared by the whole-app
// erase, the config-page rewrite and the emergency wipe.
void erase_page(std::uint16_t addr)
{
spm::erase_page<off>(addr);
spm::wait();
}
// Erase the whole application, one page at a time, top-down as the reference
// loader does (unwritten pages stay erased and the host cannot observe the
// order; the loop bound becomes a compare with zero).
void erase_application()
{
for (std::uint16_t a = app_end; a != 0;) {
a -= page;
erase_page(a);
}
spm::rww_enable<off>();
}
// The application's reset vector; the linker pins it to 0x0000 (--defsym).
extern "C" [[noreturn]] void tsb_app();
// Run the application. Any non-command byte, a wrong password, or an idle
// programmer port lands here.
[[noreturn]] void appjump()
{
spm::wait(); // make sure any pending SPM finished before handing over
tsb_app();
}
// 'f': stream the application flash back, one page per host '!'. Self-terminates
// at the application boundary; the host normally stops earlier with a non-'!'.
void read_flash()
{
for (std::uint16_t a = 0; a < app_end; a += page) {
if (rx() != confirm)
return;
send_flash(a, page);
}
}
// 'e': stream EEPROM back, one page per host '!', until the host stops.
void read_eeprom()
{
for (std::uint16_t a = 0;; a += page) {
if (rx() != confirm)
return;
send_eeprom(a, page);
}
}
// 'F': erase the whole application first, then take pages the host offers
// behind '?'.
void write_flash()
{
erase_application();
for (std::uint16_t a = 0; request_confirm(); a += page)
store_flash_page(a);
}
// 'E': take pages the host offers behind '?' into EEPROM.
void write_eeprom()
{
for (std::uint16_t a = 0; request_confirm(); a += page)
store_eeprom_page(a);
}
// 'C': replace the config page, then echo it back for the host to verify.
void write_config()
{
if (!request_confirm())
return;
erase_page(app_end);
store_flash_page(app_end);
spm::rww_enable<off>();
send_flash(app_end, page);
}
// Emergency erase: wipe the application flash, the EEPROM and the config page.
// Reachable only from the password gate (a wrong byte can never reach it), so a
// blank config still leaves the loader recoverable.
void emergency_erase()
{
erase_application();
for (std::uint16_t a = 0; a <= eeprom_end; ++a)
ee::write<off>(a, 0xff);
erase_page(app_end);
spm::rww_enable<off>();
}
// The password gate. The config page holds the password at app_end+3,
// terminated by 0xff (a blank page means no password). A byte of 0 requests
// emergency erase; a wrong byte hangs the loader, still draining the line, so a
// wrong password can never fall through to the erase.
enum class gate : std::uint8_t { pass, emergency };
gate password_gate()
{
for (const std::uint8_t *pw = flash_ptr(app_end + 3);; ++pw) {
std::uint8_t expected = avr::flash_load(pw);
if (expected == 0xff)
return gate::pass;
std::uint8_t got = rx();
if (got == 0)
return gate::emergency;
if (got != expected)
for (;;)
rx();
}
}
[[noreturn]] void run()
{
// A watchdog reset hands straight back to the application, as the reference
// loader does, rather than re-entering the bootloader.
if (avr::hw::mcusr::wdrf.test())
appjump();
avr::init<serial_t>();
// Activation: the host knocks three '@' inside a window whose length is the
// config page's timeout byte (floored so a corrupt page can never lock the
// loader out). An idle port times out and boots the application.
__uint24 idle = static_cast<__uint24>(avr::flash_load(flash_ptr(app_end + 2)) | 16) << 16;
std::uint8_t knocks = 0;
while (knocks < 3) {
if (auto byte = serial.read())
knocks = *byte == knock ? knocks + 1 : 0;
else if (--idle == 0)
appjump();
}
switch (password_gate()) {
case gate::pass:
send_flash(reinterpret_cast<std::uint16_t>(info::storage.data()), info::size());
break;
case gate::emergency:
if (!request_confirm() || !request_confirm())
appjump();
emergency_erase();
break;
}
for (;;) {
tx(confirm); // Mainloop ready
switch (rx()) {
case 'f':
read_flash();
break;
case 'F':
write_flash();
break;
case 'e':
read_eeprom();
break;
case 'E':
write_eeprom();
break;
case 'c':
send_flash(app_end, page);
break;
case 'C':
write_config();
break;
default:
appjump(); // 'q' or any other byte runs the application
}
}
}
} // namespace
} // namespace tsb
// Reset lands here: BOOTRST vectors to the boot section base and .vectors is
// laid first, so this is the first instruction executed. No crt ran, so set the
// stack pointer before anything is called.
extern "C" [[gnu::naked, gnu::used, gnu::section(".vectors")]] void __boot_entry()
{
SP = RAMEND;
// The one line of crt this loader needs: compiled code assumes
// __zero_reg__ (r1) is 0, and power-on registers are undefined.
asm volatile("clr __zero_reg__");
tsb::run();
}

363
tsb/tsb_tricks.cpp Normal file
View File

@@ -0,0 +1,363 @@
// TinySafeBoot on libavr — tier 2: C++ with compiler trickery, no assembly.
//
// The full TinySafeBoot feature set — watchdog bail, one-wire half-duplex,
// config-page activation timeout, password gate, emergency erase, and
// config/flash/EEPROM read-write — in pure C++, 526 bytes: 14 over the 512-byte
// boot section the hand-written oracle fits, from 168 over at this tier's first
// floor. The structure mirrors the oracle's: a handful of tiny noinline
// primitives sharing one whole-loader register allocation, expressed as global
// register variables so no helper ever saves, spills, or reloads any of it.
//
// The register protocol (all call-saved, so calls preserve them by ABI):
// Y (r28:r29) g_addr the walked flash/EEPROM address — adiw-able
// r16 g_cnt byte countdown of the running block — ldi-able
// r7 g_window rx timeout, roughly 30 ms units at 16 MHz
// r6 g_receiving one-wire direction latch, cleared at bring-up
// (power-on registers are undefined)
//
// GCC 16.1 miscompiles stores into global register variables: an update whose
// remaining uses all hide inside callees is deleted whenever a CALL follows it
// before any jump/ret (the backend's liveness walk lumps fixed registers with
// call-clobbered ones — minimal repro in libavr's
// local/scratch/probes/gcc-avr-globalreg-repro.cpp, lessons.md entry). Every
// g_* update below therefore sits where a *local* read or a jump/ret follows
// it — the helpers advance g_addr immediately before returning, and rx()
// re-floors the window on every call instead of storing the floored value
// once. The layout is load-bearing; do not "simplify" it.
//
// The wire protocol is strict request/response, which is what makes the shared
// line safe: the device drives it only between a received command and its
// reply, and releases it (RXEN0 only) whenever it waits.
#include <libavr/libavr.hpp>
#include <avr/io.h> // SP / RAMEND for the crt-free boot entry
using namespace avr::literals;
namespace spm = avr::spm;
namespace ee = avr::eeprom;
namespace hw = avr::hw;
namespace tsb {
namespace {
// The loader is purely polled — it never enables interrupts — so every SPM and
// EEPROM lock folds to nothing under this posture.
constexpr auto off = avr::irq::guard_policy::unused;
constexpr std::uint8_t confirm = '!';
constexpr std::uint8_t request = '?';
constexpr std::uint8_t knock = '@';
// Boot geometry for the 1 KB boot section (BOOTSZ=10); the page size and the
// flash/EEPROM extents are the chip database's to know. app_end is the config
// page (TSB's LASTPAGE), one page below the boot section.
constexpr std::uint16_t page = spm::page_bytes;
constexpr std::uint16_t boot_bytes = 1024;
constexpr std::uint16_t app_end = spm::flash_bytes - boot_bytes - page;
constexpr std::uint16_t eeprom_end = avr::hw::db.mem.eeprom_size - 1;
// Lockout-proof floor for the activation window (the oracle's F_CPU/1MHz).
constexpr std::uint8_t act_min = 16;
// Post-activation window: the host gets seconds, not milliseconds, mid-session.
constexpr std::uint8_t comm_window = 200;
constexpr std::uint16_t build_date = 26 * 512 + 7 * 32 + 20;
// Fixed 115200 8N1; the library solves UBRR + U2X from clock and baud.
constexpr auto baud = avr::uart::solve_baud(16_MHz, 115200_Bd);
// The 16-byte device-info block, streamed out on activation.
// clang-format off
[[gnu::progmem]] constexpr std::uint8_t info[16] = {
'T', 'S', 'B',
build_date & 0xFF, build_date >> 8,
0xF3, // status: native-UART fixed-baud lineage
0x1E, 0x95, 0x0F, // ATmega328P signature
page / 2, // page size in words
(app_end / 2) & 0xFF, (app_end / 2) >> 8,
eeprom_end & 0xFF, eeprom_end >> 8,
0xAA, 0xAA,
};
// clang-format on
register std::uint16_t g_addr asm("r28");
register std::uint8_t g_cnt asm("r16");
register std::uint8_t g_window asm("r7");
register std::uint8_t g_receiving asm("r6");
const std::uint8_t *flash_ptr(std::uint16_t addr)
{
return reinterpret_cast<const std::uint8_t *>(addr);
}
// Bounded byte receive, the oracle's shape: release the one-wire line on a
// direction change, poll RXC0 under nested countdowns, 0 on silence. The 0
// then falls through every compare — not a knock, not a confirm, not a
// command — so a silent host unwinds the loader to the application from
// anywhere, and a mid-session cable pull cannot wedge it.
[[gnu::noinline, gnu::noclone]] std::uint8_t rx()
{
if (!g_receiving) {
g_receiving = 1;
hw::ucsr0b::write(hw::ucsr0b::rxen0(1)); // RXEN0 alone: release and listen
}
// act_min ORs in here, per call, not once into g_window at setup — the
// one placement the global-register-store miscompile cannot delete.
std::uint16_t outer = static_cast<std::uint16_t>(g_window | act_min) << 8;
do {
std::uint8_t fine = 0;
do {
auto status = hw::ucsr0a::read();
if (status & hw::ucsr0a::rxc0(1).value)
return hw::udr0::read();
} while (--fine);
} while (--outer);
return 0;
}
// One-wire transmit: take the line (TXEN0 alone — the receiver must be off
// while driving) on a direction change, with a turn-around guard so a shorted
// peer can switch first; then hold the line until the whole frame is out
// (TXC0, not UDRE0 — the stop bit must be on the wire before a caller may
// release the line), and W1C TXC0 by storing the sampled status back, which
// keeps U2X0.
[[gnu::noinline, gnu::noclone]] void tx(std::uint8_t byte)
{
if (g_receiving) {
g_receiving = 0;
hw::ucsr0b::write(hw::ucsr0b::txen0(1));
for (std::uint8_t guard = 46; guard; --guard)
;
}
hw::udr0::write(byte);
std::uint8_t status;
do {
status = hw::ucsr0a::read();
} while (!(status & hw::ucsr0a::txc0(1).value));
hw::ucsr0a::write(status);
}
// '?', then hand back the host's reply for the callers' one-byte compare.
[[gnu::noinline, gnu::noclone]] std::uint8_t rcnf()
{
tx(request);
return rx();
}
// One flash byte ← [g_addr++] (the advance right before ret — see header).
[[gnu::noinline, gnu::noclone]] std::uint8_t sflash()
{
std::uint8_t byte = avr::flash_load(flash_ptr(g_addr));
++g_addr;
return byte;
}
// One EEPROM byte ← [g_addr++].
[[gnu::noinline, gnu::noclone]] std::uint8_t eerd()
{
std::uint8_t byte = ee::read(g_addr);
++g_addr;
return byte;
}
// One EEPROM byte → [g_addr++].
[[gnu::noinline, gnu::noclone]] void eewr(std::uint8_t byte)
{
ee::write<off>(g_addr, byte);
++g_addr;
}
// Stream g_cnt flash bytes from g_addr to the host.
[[gnu::noinline, gnu::noclone]] void sendf()
{
do {
tx(sflash());
} while (--g_cnt);
}
// Wait out a running SPM op, then re-open the RWW section — after every page
// op and before handing over, as the oracle does.
[[gnu::noinline, gnu::noclone]] void settle()
{
spm::wait();
spm::rww_enable<off>();
}
extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --defsym=tsb_app=0
[[noreturn]] void appjump()
{
settle();
tsb_app();
}
// Step g_addr one page down and erase that page. The decrement lives in here,
// before the erase's own use of it, not in the caller's loop where a following
// call would get it deleted (see header).
[[gnu::noinline, gnu::noclone]] void erase_below()
{
g_addr -= page;
spm::erase_page<off>(g_addr);
settle();
}
// Erase the whole application, top-down like the oracle: the loop bound is a
// compare with zero, and g_addr = 0 — the value every caller wants next — is
// handed back for free.
[[gnu::noinline, gnu::noclone]] void erase_application()
{
g_addr = app_end;
do {
erase_below();
} while (g_addr != 0);
}
// Stream one host page into the erased flash page at g_addr (SPM word buffer,
// low byte then high) — no SRAM staging, receive and program are one loop.
// g_addr is left at the next page base.
[[gnu::noinline, gnu::noclone]] void store_flash()
{
g_cnt = page / 2;
do {
std::uint16_t word = rx();
word |= static_cast<std::uint16_t>(rx()) << 8;
spm::fill<off>(g_addr, word);
g_addr += 2;
} while (--g_cnt);
spm::write_page<off>(g_addr - page);
settle();
}
[[noreturn, gnu::noinline]] void run()
{
// A watchdog reset hands straight back to the application, as the
// reference loader does, rather than re-entering the bootloader.
if (hw::mcusr::wdrf.test())
appjump();
// Lean bring-up from reset state: UCSR0C already reads 8N1, UBRR0H reads
// 0, and rx()/tx() raise RXEN0/TXEN0 on first use — only the divisor low
// byte and U2X0 need a store. The library still does the datasheet work.
static_assert(baud.u2x && baud.ubrr < 256, "lean bring-up writes UBRR0L only, with U2X0");
hw::ubrr0::write(static_cast<std::uint8_t>(baud.ubrr));
hw::ucsr0a::write(hw::ucsr0a::u2x0(1));
// General-purpose registers are undefined at power-on (no crt zeroes them);
// the direction latch must start "not receiving" so the first rx() enables
// the receiver. The reference loader clears its shadow register for the
// same reason.
g_receiving = 0;
// Activation: 3×'@', each inside the config page's timeout window (rx
// floors it so a corrupt page cannot lock the loader out); anything else —
// including silence — hands over.
g_window = avr::flash_load(flash_ptr(app_end + 2));
for (std::uint8_t k = 3; k; --k)
if (rx() != knock)
appjump();
g_window = comm_window;
// Password gate (config page from app_end+3, 0xff-terminated; a blank
// page is no password). A wrong byte blanks the comparison and drains the
// line forever, so a wrong password can never fall through; a 0 requests
// emergency erase behind two confirms. On pass the info block goes out;
// the emergency path skips it and drops into the command loop.
g_addr = app_end + 3;
std::uint8_t mask = 0xff;
for (;;) {
std::uint8_t expected = avr::flash_load(flash_ptr(g_addr)) & mask;
++g_addr;
if (expected == 0xff) {
g_addr = reinterpret_cast<std::uint16_t>(&info[0]);
g_cnt = sizeof(info);
sendf();
break;
}
std::uint8_t got = rx();
if (got == 0) {
if (mask == 0)
continue;
if (rcnf() != confirm || rcnf() != confirm)
appjump();
erase_application(); // leaves g_addr = 0 for the EEPROM walk
do {
eewr(0xff);
} while (g_addr <= eeprom_end);
g_addr = app_end + page;
erase_below();
break;
}
if (got != expected)
mask = 0;
}
for (;;) {
tx(confirm); // Mainloop ready
g_addr = 0;
switch (rx()) {
case 'f': // read application flash, one page per host '!'
for (;;) {
if (rx() != confirm)
break;
g_cnt = page;
sendf();
if (g_addr >= app_end)
break;
}
break;
case 'F': // erase the application, then take pages behind '?'
erase_application(); // leaves g_addr = 0, the write start
while (rcnf() == confirm)
store_flash();
break;
case 'e': // read EEPROM, one page per host '!', until the host stops
for (;;) {
if (rx() != confirm)
break;
g_cnt = page;
do {
tx(eerd());
} while (--g_cnt);
}
break;
case 'E': // take EEPROM pages behind '?'
while (rcnf() == confirm) {
g_cnt = page;
do {
eewr(rx());
} while (--g_cnt);
}
break;
case 'c': // read the config page
read_config:
g_addr = app_end;
g_cnt = page;
sendf();
break;
case 'C': // replace the config page, then echo it back to verify
if (rcnf() != confirm)
break;
g_addr = app_end + page;
erase_below(); // leaves g_addr = app_end, the store target
store_flash();
goto read_config;
default: // 'q' or any other byte runs the application
appjump();
}
}
}
} // namespace
} // namespace tsb
// Reset lands here: BOOTRST vectors to the boot section base and .vectors is
// laid first, so this is the first instruction executed. No crt ran, so set
// the stack pointer before anything is called.
extern "C" [[gnu::naked, gnu::used, gnu::section(".vectors")]] void __boot_entry()
{
SP = RAMEND;
// The one line of crt this loader needs: compiled code assumes
// __zero_reg__ (r1) is 0, and power-on registers are undefined.
asm volatile("clr __zero_reg__");
tsb::run();
}

1
tsb/type

Submodule tsb/type deleted from ce31ef017f

1
tsb/uart

Submodule tsb/uart deleted from 8f88cdccea