pureboot 3: a 512-byte slot on every chip, the 1284s included

The word-addressed 1284s were the one family deploying in a 1 KiB slot,
because the far-flash machinery (ELPM reads, RAMPZ page commands, a
word-addressed wire) did not fit 512 B. It does now: 478 B stock, 494 B in
the heaviest configuration the build can produce. They take the 644s'
geometry, where the smallest boot section holds the resident slot and its
staging slot together. The loader's version goes to 3; the host tool did
not change, so its own version stays 2 and only the window it speaks
widens.

Most of the saving is one restructure. The info block and a flash read are
the same act, so giving all four streamed commands one address-and-count
path leaves exactly one call site for the flash streamer: it inlines into
the never-returning command loop and its 24-bit cursor stops being saved
and restored around every transmit. Around it, the ack byte moved out of
line, the wire's byte pair is bit_cast into the word it already is, the
fuse loop ends on its count, the info block's in-slot offset is taken as
the one-byte relocation it is, and -fno-expensive-optimizations gives way
to -fno-move-loop-invariants -fno-tree-ter. Every chip shrank 14-18 B.

The size matrix grew the axes it was missing: the USART1 instance across
the whole clock ladder, and the shape a slow baud gives a software UART —
past 255 delay iterations libavr takes the 16-bit delay loop, which the
ladder default never selects and which was 4 B over the 1284's slot the
first time it was built.

The protocol fixture stopped deriving the loader entry from the flash
size; on the 1284s it had been jumping a slot low and reaching the loader
only because erased flash walked it up.

Docs and comments were consolidated across the port in the same pass: the
README carries a per-chip size table instead of prose, and prose that
restated the code is gone — 190 lines, no behaviour with it.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>

.clang-format

@@ -7,9 +7,8 @@ TabWidth: 4
 UseTab: ForIndentation
 AlignEscapedNewlines: DontAlign
 AllowShortFunctionsOnASingleLine: Empty
-BreakTemplateDeclarations: Yes
+AlwaysBreakTemplateDeclarations: true
 BreakBeforeBraces: Custom
 BraceWrapping:
   AfterFunction: true
-InsertBraces: true
 ...

.clangd

@@ -1,38 +0,0 @@
-# Editor accommodations for the second frontend. No compilation database is
-# named here: this repo rides as a submodule in its consumers, and this file
-# travels with it — a consumer's own database then covers these sources, with
-# that project's loader flags. The checkout that is opened as a folder names
-# its build tree in .vscode/settings.json instead.
-CompileFlags:
-  Add:
-    # clang has no 24-bit integer and GCC's are keywords, not macros, so the
-    # editor needs a stand-in for avr::uint24_t. The next width up is the only
-    # one available — clang rejects _BitInt(24) on this target.
-    - -D__uint24=unsigned long
-    - -D__int24=long
-    # clangd forwards the driver's system includes but not its own header
-    # directory, so <stdint.h> resolves to avr-libc's, which still gates the
-    # limit and constant macros on the C++98 opt-in.
-    - -D__STDC_LIMIT_MACROS
-    - -D__STDC_CONSTANT_MACROS
-    # isr::emit spells a vector number into [[gnu::signal(N)]], which clang
-    # rejects rather than ignores — enough of them in one TU to reach the
-    # default limit of 19 inside the headers and truncate the parse.
-    - -ferror-limit=0
-  Remove:
-    # Codegen shaping the loader TUs carry and clang has no spelling for.
-    - -fira-algorithm=*
-    - -fno-split-wide-types
-    - -fno-tree-ter
-    - -fno-ivopts
-    - -fno-move-loop-invariants
-    # The build promotes warnings for the compiler that has to be right about
-    # them; in the editor the flag paints a second frontend's opinions in the
-    # colour reserved for things that do not compile.
-    - -Werror
-Diagnostics:
-  Suppress:
-    # clang's AVR `signal` attribute takes no arguments and it knows none of
-    # progmem, naked or OS_main. A misspelling is what the build is for.
-    - attribute_wrong_number_arguments
-    - unknown-attributes

.gitattributes

@@ -1,11 +1,8 @@
-# Line endings are the repository's, not the editing machine's: this checkout
+*.h         eol=lf
-# is reached from two hosts, and a file rewritten by a Windows tool comes back
+*.hpp       eol=lf
-# with every line changed unless something says otherwise. Naming the source
+*.c         eol=lf
-# extensions left Markdown, Python, shell and CMake to whatever the writing
+*.cpp       eol=lf
-# tool defaulted to, which is CRLF on one of the two.
+.git*       eol=lf
-* text=auto eol=lf
-
-# Atmel Studio writes these and expects them back.
 *.vcxproj*  eol=crlf
 *.cppproj   eol=crlf
 *.sln       eol=crlf

.gitignore

@@ -12,7 +12,6 @@ Debug
 
 # CMake / clangd
 /build/
-/local/
 compile_commands.json
 .cache/
 

.gitmodules

@@ -1,3 +0,0 @@
-[submodule "libavr"]
-	path = libavr
-	url = ../libavr.git

.vscode/extensions.json

@@ -1,6 +0,0 @@
-{
-	"recommendations": [
-		"llvm-vs-code-extensions.vscode-clangd",
-		"ms-vscode.cmake-tools"
-	]
-}

.vscode/settings.json

@@ -1,36 +0,0 @@
-{
-	// clangd is the language server; the cpptools engine would parse every file
-	// a second time and disagree, since nothing tells it about a cross
-	// compiler.
-	"C_Cpp.intelliSenseEngine": "disabled",
-
-	// --query-driver lets clangd ask the cross compiler for its own system
-	// includes and target. The database is named here rather than in .clangd
-	// because that file travels with the driver into a consumer's submodule,
-	// where a build tree of this repo's own need not exist.
-	"clangd.arguments": [
-		"--compile-commands-dir=${workspaceFolder}/build/atmega328p-generated",
-		"--query-driver=**avr-g++*",
-		"--header-insertion=never"
-	],
-
-	// The presets are the build interface, and the toolchain file inside the
-	// libavr submodule is the one place the compiler is chosen. **No prefix is
-	// named here**: a committed file may not name a path that is true of one
-	// machine (libavr guidance rule 50), so the gitignored local/machine.cmake
-	// at this repository's root is where a checkout says where its toolchain
-	// is - one file, and it answers for both hosts.
-	"cmake.useCMakePresets": "always",
-	"cmake.configureOnOpen": true,
-	"cmake.options.statusBarVisibility": "compact",
-
-	"files.watcherExclude": {
-		"**/build/**": true,
-		"**/libavr/**": true
-	},
-
-	"files.associations": {
-		".clangd": "yaml",
-		".clang-format": "yaml"
-	}
-}

CMakeLists.txt

@@ -2,78 +2,61 @@ cmake_minimum_required(VERSION 3.28)
 
 project(tsb_libavr LANGUAGES CXX)
 
-# libavr rides as the pinned submodule; LIBAVR_ROOT (cache or environment)
+# libavr from a local checkout (LIBAVR_ROOT) or the forge; the toolchain file
-# overrides it for tandem development against a working tree. The toolchain
+# comes from the same checkout via CMakePresets.json.
-# file comes from the submodule via CMakePresets.json either way.
+include(FetchContent)
 if(NOT LIBAVR_ROOT AND DEFINED ENV{LIBAVR_ROOT})
 	set(LIBAVR_ROOT $ENV{LIBAVR_ROOT})
 endif()
-if(NOT LIBAVR_ROOT)
+if(LIBAVR_ROOT)
-	set(LIBAVR_ROOT ${CMAKE_CURRENT_SOURCE_DIR}/libavr)
+	FetchContent_Declare(libavr SOURCE_DIR ${LIBAVR_ROOT})
+else()
+	FetchContent_Declare(libavr GIT_REPOSITORY git@git.blackmark.me:avr/libavr.git GIT_TAG main)
 endif()
-if(NOT EXISTS ${LIBAVR_ROOT}/CMakeLists.txt)
+FetchContent_MakeAvailable(libavr)
-	message(FATAL_ERROR "libavr not found at ${LIBAVR_ROOT} - run: git submodule update --init libavr")
-endif()
-add_subdirectory(${LIBAVR_ROOT} libavr-build)
-
-include(${LIBAVR_ROOT}/cmake/checks.cmake)
 
 if(PROJECT_IS_TOP_LEVEL)
 	add_compile_options(-Werror) # warnings are errors for the port's own code
 	enable_testing()
 
-	# Rules 11 and 33 over this repo's own sources. The oracle's assembly needs
-	# no exclusion: it is neither formatted nor ASCII-checked, being in neither
-	# glob, which is the right answer for a vendored reference whose text is
-	# the artifact.
-	libavr_format_test()
-
 	# The behavioral tests drive the real wire protocols over a simavr pty
-	# (as the host tools do) and actually flash the device. The runner is a
+	# (as the host tools do) and actually flash the device. The runners are
-	# host program built at configure time against libsimavr (C++23 - what the
+	# host programs built at configure time against libsimavr; if they or
-	# distribution's compiler speaks in full).
+	# Python are missing, only the size tests run.
-	#
+	find_program(_host_cc NAMES cc gcc)
-	# **A host that cannot build it registers those tests anyway and skips
+	find_package(Python3 COMPONENTS Interpreter)
-	# them.** They used to be left out, which makes the suite a different size
+	if(_host_cc AND Python3_FOUND)
-	# on a different machine - and a suite whose size is a property of the
+		set(PB_DEVICE ${CMAKE_BINARY_DIR}/pureboot_device)
-	# machine is one nothing can be compared against.
-	set(TSB_DEVICE ${CMAKE_BINARY_DIR}/tsb_device)
-	find_program(_host_cxx NAMES c++ g++)
-	set(_tsb_absent "${LIBAVR_NO_PYTHON}")
-	if(NOT _host_cxx)
-		set(_tsb_absent "no host C++ compiler on PATH, and the simavr device is a host program")
-	elseif(NOT _tsb_absent)
 		execute_process(
-		    COMMAND ${_host_cxx} -std=c++23 -Wall -Wextra -O2
+		    COMMAND ${_host_cc} -O2 -I/usr/include/simavr -I/usr/include/simavr/parts
-		            -I/usr/include/simavr -I/usr/include/simavr/parts
+		            -o ${PB_DEVICE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pureboot_device.c
-		            -o ${TSB_DEVICE} ${CMAKE_CURRENT_SOURCE_DIR}/test/device.cpp
+		            -lsimavr -lsimavrparts -lelf -lutil
+		    RESULT_VARIABLE _pbdev_res ERROR_VARIABLE _pbdev_err)
+		if(NOT _pbdev_res EQUAL 0)
+			message(STATUS "pureboot_device not built (${_pbdev_err}) — protocol tests skipped")
+			unset(PB_DEVICE)
+		endif()
+		if(LIBAVR_MCU STREQUAL "atmega328p")
+			set(TSB_DEVICE ${CMAKE_BINARY_DIR}/tsb_device)
+			execute_process(
+			    COMMAND ${_host_cc} -O2 -I/usr/include/simavr -I/usr/include/simavr/parts
+			            -o ${TSB_DEVICE} ${CMAKE_CURRENT_SOURCE_DIR}/test/device.c
 			            -lsimavr -lsimavrparts -lelf
 			    RESULT_VARIABLE _dev_res ERROR_VARIABLE _dev_err)
 			if(NOT _dev_res EQUAL 0)
-			# One bounded line of it: this becomes a single argument on a
+				message(STATUS "tsb_device not built (${_dev_err}) — protocol tests skipped")
-			# command line, and the reading has to say what stopped the build
+				unset(TSB_DEVICE)
-			# rather than that something did.
-			string(REGEX REPLACE "[\r\n\t]+" " " _dev_err "${_dev_err}")
-			string(REPLACE ";" "," _dev_err "${_dev_err}")
-			string(LENGTH "${_dev_err}" _dev_len)
-			if(_dev_len GREATER 240)
-				string(SUBSTRING "${_dev_err}" 0 240 _dev_err)
-			endif()
-			set(_tsb_absent "test/device.cpp does not build here: ${_dev_err}")
 			endif()
 		endif()
-	libavr_launcher(_tsb_python "${_tsb_absent}" ${Python3_EXECUTABLE})
-	if(_tsb_absent)
-		message(STATUS "the protocol tests skip here - ${_tsb_absent}")
 	endif()
 endif()
 
-# The ELF is only a container (symbols, section headers) and is never flashed -
+# The ELF is only a container (symbols, section headers) and is never flashed —
 # and the host tool's load_image() dispatches on extension, so handing it one
 # would silently program the header bytes. Every loader image therefore gets
 # both flashable forms beside it at link time: .hex for avrdude, and .bin for
 # the host tool's raw path (which is what the reloc and update tests convert to
-# on the fly). .eeprom is dropped - EEPROM content is its own update.
+# on the fly). .eeprom is dropped — EEPROM content is its own update.
 function(add_image_outputs name)
 	add_custom_command(TARGET ${name} POST_BUILD
 	                   COMMAND ${CMAKE_OBJCOPY} -O ihex -R .eeprom
@@ -82,39 +65,35 @@ function(add_image_outputs name)
 	                           $<TARGET_FILE:${name}> $<TARGET_FILE:${name}>.bin)
 endfunction()
 
-# The TinySafeBoot protocol reimplemented on libavr in variants that trade
+# The TinySafeBoot protocol reimplemented on libavr in three variants that trade
 # clarity for size. Each links into the ATmega328P boot section (BOOTSZ selects
-# its size; BOOTRST vectors a reset to its base) with -nostartfiles - a polled
+# its size; BOOTRST vectors a reset to its base) with -nostartfiles — a polled
-# loader has no use for the crt or the vector table. The entry sits in
+# loader has no use for the crt or the vector table. The naked entry sits in
-# .vectors, laid first, and runs - avr::startup::entry on the policy tier,
+# .vectors, laid first, and runs. The boot base is FLASHEND+1 minus the section
-# the experiment tiers' own naked stubs elsewhere, each documented in its
+# size; the linker section-start and the source's boot_bytes agree. tsb_app is
-# source. The boot base is FLASHEND+1 minus the section size; the linker
-# section-start and the source's boot_bytes agree. tsb_app is
 # the application's reset vector, pinned to 0 here so the loaders jump to a
 # named function; --pmem-wrap-around lets relaxation turn that absolute jump
 # into the wrapped rjmp AVR's modulo-flash PC actually executes.
-# All four implement the full oracle feature set (see oracle/README.md):
+# All three implement the full oracle feature set (see oracle/README.md):
 # watchdog bail, one-wire half-duplex, config-page activation timeout, password
 # gate, emergency erase, config/flash/EEPROM read-write. They differ only in how,
-# and the size gradient is the cost of that "how".
+# and the size gradient is the cost of that "how" — see dev/lessons.md.
-#   tsb_asm    - the tricks tier's C++ with exactly two routines in asm: the
+#   tsb_asm   — the tricks tier's C++ with exactly two routines in asm (the
-#                 bounded rx and the page-store loop, the two whose remaining
+#                 bounded rx and the page-store loop — the two whose remaining
-#                 cost is the C ABI itself. Everything else, bring-up to
+#                 cost is the C ABI itself): 510 B in the 512 B section the
-#                 dispatch, is C++ on libavr.
+#                 hand-written 500 B oracle occupies. Everything else, from
-#   tsb_tricks - no asm at all: the whole-loader register allocation lives in
+#                 bring-up to dispatch, is C++ on libavr.
+#   tsb_tricks — no asm at all: the whole-loader register allocation lives in
 #                 global register variables (Y walks the page pointer), every
 #                 helper is a tiny noinline primitive placed by the
 #                 global-register store rules, pages stream straight to
-#                 SPM/EEPROM.
+#                 SPM/EEPROM, and the bring-up is the two reset-non-default
-#   tsb_pure   - pure idiomatic libavr, one function per command, TU-local
+#                 registers only. 526 B in the 1 KB section (BOOTSZ=10) — 14
-#                 (internal linkage), streaming (no SRAM page buffer).
+#                 over the oracle's section, from 168 over at this tier's first
-#   tsb_policy - the policy floor: no inline assembly and no global register
+#                 floor.
-#                 variables, which is philosophy #5's own bound, and the
+#   tsb_pure  — pure idiomatic libavr, one function per command, TU-local
-#                 measured evidence that the 512 B fit is a property of the
+#                 (internal linkage), streaming (no SRAM page buffer): 836 B in
-#                 mechanisms it bans.
+#                 the 1 KB section.
-#
-# What each measures is oracle/README.md's table, which is the one place the
-# four numbers and the hand-written loader's own are compared.
 #
 # add_tsb_variant(<name> <boot-section-bytes>)
 function(add_tsb_variant name bytes)
@@ -130,28 +109,226 @@ function(add_tsb_variant name bytes)
 		add_test(NAME ${name}.size
 		         COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:${name}>
 		                 -DLIMIT=${bytes} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
+		if(DEFINED TSB_DEVICE)
 			add_test(NAME ${name}.protocol
-		         COMMAND ${_tsb_python} ${CMAKE_CURRENT_SOURCE_DIR}/test/tsbtest.py
+			         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/tsbtest.py
 			                 ${TSB_DEVICE} $<TARGET_FILE:${name}> ${base_hex})
 		endif()
+	endif()
 endfunction()
 
-# The tiers reimplement the ATmega328P-only reference protocol, so the guard is
+# The tsb tiers reimplement the ATmega328P-only reference protocol; the other
-# the whole of what this repo builds.
+# chips build pureboot alone.
 if(LIBAVR_MCU STREQUAL "atmega328p")
 	add_tsb_variant(tsb_asm 512)
-	add_tsb_variant(tsb_policy 1024)
 	add_tsb_variant(tsb_pure 1024)
 	add_tsb_variant(tsb_tricks 1024)
-	# The policy tier's floor needs these two: a loader's loop bodies all
-	# contain calls, which is what makes hoisting an invariant out of one cost
-	# more than it saves. The other tiers keep the flag set their recorded
-	# floors were measured with - none.
-	target_compile_options(tsb_policy PRIVATE -fno-move-loop-invariants -fno-tree-ter)
 endif()
 
-# Every test registered above carries the marker a stubbed launcher prints, so
+# pureboot — the pure-constraint port (see pureboot/README.md): one source,
-# a check this host cannot run reads as Skipped rather than Failed.
+# no inline assembly, no global register variables, every libavr chip,
+# fitting each chip's smallest boot sector. The geometry and the
+# pureboot_add_loader() deployment function live in pureboot/CMakeLists.txt —
+# the unit a downstream project consumes; everything below is this port's
+# own build: the stock loaders, their tests, and the size matrix. The
+# distinct binary dir keeps the `pureboot` target's output name free.
+add_subdirectory(pureboot pureboot-cmake)
+
+# The stock loader: the family-default deployment (crystal/RC clock, the
+# chip's natural link, default pins). The activation window stays a cache
+# variable — re-timing a deployed loader is a self-update with a re-timed
+# build. pureboot9 is that re-timed build, and what the update test installs.
+set(PUREBOOT_TIMEOUT 8 CACHE STRING "pureboot activation window, seconds")
+pureboot_add_loader(pureboot TIMEOUT ${PUREBOOT_TIMEOUT})
 if(PROJECT_IS_TOP_LEVEL)
-	libavr_skip_unverified()
+	get_target_property(_pb_stock_hz pureboot PUREBOOT_HZ)
+	get_target_property(_pb_stock_baud pureboot PUREBOOT_BAUD)
+
+	add_test(NAME pureboot.size
+	         COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:pureboot>
+	                 -DLIMIT=${PUREBOOT_LIMIT} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
+	if(Python3_FOUND)
+		add_test(NAME pureboot.pi
+		         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/check_pi.py
+		                 ${CMAKE_OBJDUMP} ${CMAKE_NM} $<TARGET_FILE:pureboot> ${PUREBOOT_BASE_HEX})
+		add_test(NAME pureboot.planner
+		         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/test_planner.py
+		                 ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py)
+	endif()
+
+	# The protocol test flashes this fixture through the loader with the real
+	# host tool and expects its banner after the hand-over; a normally linked
+	# application whose reset vector is what the tinies' surgery re-homes.
+	if(DEFINED PB_DEVICE)
+		add_executable(pbapp test/pbapp.cpp)
+		target_link_libraries(pbapp PRIVATE libavr)
+		add_custom_command(TARGET pbapp POST_BUILD
+		                   COMMAND ${CMAKE_OBJCOPY} -O binary $<TARGET_FILE:pbapp> $<TARGET_FILE:pbapp>.bin)
+		add_test(NAME pureboot.protocol
+		         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
+		                 ${PB_DEVICE} $<TARGET_FILE:pureboot> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
+		                 ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud} ${PUREBOOT_EEPROM}
+		                 $<TARGET_FILE:pbapp>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
+		                 ${CMAKE_BINARY_DIR}/pbtest-work)
+		set_tests_properties(pureboot.protocol PROPERTIES TIMEOUT 180)
+
+		# The position-independence acceptance test: the identical image,
+		# installed one slot lower, must serve the full command set.
+		add_test(NAME pureboot.reloc
+		         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbreloc.py
+		                 ${PB_DEVICE} $<TARGET_FILE:pureboot> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
+		                 ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud}
+		                 ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
+		                 ${CMAKE_BINARY_DIR}/pbreloc-work)
+		set_tests_properties(pureboot.reloc PROPERTIES TIMEOUT 180
+		                     ENVIRONMENT "PB_OBJCOPY=${CMAKE_OBJCOPY}")
+
+		# Entering the loader from a running application with no reset
+		# between, over a page buffer the application dirtied — the case the
+		# loader declines to guard and the host repairs. Hardware forbids the
+		# state here (SPM runs only from the boot section); simavr does not,
+		# which is what makes it constructible.
+		if(LIBAVR_MCU STREQUAL "atmega328p")
+			add_test(NAME pureboot.dirty
+			         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbdirty.py
+			                 ${PB_DEVICE} $<TARGET_FILE:pureboot> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
+			                 ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud}
+			                 $<TARGET_FILE:pbapp>.bin
+			                 ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
+			                 ${CMAKE_BINARY_DIR}/pbdirty-work)
+			set_tests_properties(pureboot.dirty PROPERTIES TIMEOUT 180)
+		endif()
+
+		# Re-homing: a loader mistakenly programmed at address 0 (a raw .bin
+		# handed to a programmer) or sitting in the staging slot must heal
+		# into the canonical slot through the ordinary --update-loader flow.
+		# Patched-vector behavior, so one representative chip carries it.
+		if(LIBAVR_MCU STREQUAL "attiny85")
+			add_test(NAME pureboot.rehome
+			         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbrehome.py
+			                 ${PB_DEVICE} $<TARGET_FILE:pureboot> $<TARGET_FILE:pureboot9>.bin
+			                 ${PUREBOOT_SIM_MCU} ${_pb_stock_hz} ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE}
+			                 ${_pb_stock_baud} $<TARGET_FILE:pbapp>.bin
+			                 ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
+			                 ${CMAKE_BINARY_DIR}/pbrehome-work)
+			set_tests_properties(pureboot.rehome PROPERTIES TIMEOUT 180)
+		endif()
+
+		# The self-update end-to-end: the re-timed build (same source, only
+		# the timeout differs — a byte-different image) replaces the resident
+		# through --update-loader, with every power-fail phase rehearsed from
+		# the runner's flash dumps.
+		pureboot_add_loader(pureboot9 TIMEOUT 9)
+		add_test(NAME pureboot.update
+		         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbupdate.py
+		                 ${PB_DEVICE} $<TARGET_FILE:pureboot> $<TARGET_FILE:pureboot9>
+		                 ${PUREBOOT_SIM_MCU} ${_pb_stock_hz} ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE}
+		                 ${_pb_stock_baud} $<TARGET_FILE:pbapp>.bin
+		                 ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
+		                 ${CMAKE_BINARY_DIR}/pbupdate-work)
+		set_tests_properties(pureboot.update PROPERTIES TIMEOUT 600
+		                     ENVIRONMENT "PB_OBJCOPY=${CMAKE_OBJCOPY}")
+	endif()
+
+	# The size matrix: every configuration axis that could move the image
+	# size — the serial backend (different code), the USART instance
+	# (different registers), the clock (different constants), and the baud
+	# through the two shapes its bit timing takes — each combination must
+	# still fit the chip's slot budget. Pins are size-neutral (port and bit
+	# are immediate operands) and the timeout is a constant, so neither adds
+	# an axis. The stock build is one point of this matrix and already has
+	# its test.
+	function(pureboot_size_variant name)
+		pureboot_add_loader(${name} ${ARGN})
+		add_test(NAME ${name}.size
+		         COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:${name}>
+		                 -DLIMIT=${PUREBOOT_LIMIT} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
+	endfunction()
+
+	# Clock points: the shipped-fuse floor (CKDIV8), the calibrated RC, and
+	# the crystal the stock build assumes (the tiny13's ladder is its own RC
+	# menu — it has no crystal option).
+	if(LIBAVR_MCU MATCHES "^attiny13")
+		set(_matrix_clocks 1200000 4800000 9600000)
+	else()
+		set(_matrix_clocks 1000000 8000000 16000000)
+	endif()
+	foreach(_matrix_hz IN LISTS _matrix_clocks)
+		math(EXPR _matrix_khz "${_matrix_hz} / 1000")
+		if(PUREBOOT_HAS_USART OR NOT _matrix_hz EQUAL _pb_stock_hz)
+			pureboot_size_variant(pureboot_sw_${_matrix_khz}k CLOCK ${_matrix_hz} SERIAL software)
+		endif()
+		if(PUREBOOT_HAS_USART AND NOT _matrix_hz EQUAL _pb_stock_hz)
+			pureboot_size_variant(pureboot_hw_${_matrix_khz}k CLOCK ${_matrix_hz} SERIAL hardware)
+		endif()
+		if(PUREBOOT_HAS_USART1 AND NOT _matrix_hz EQUAL _pb_stock_hz)
+			pureboot_size_variant(pureboot_usart1_${_matrix_khz}k CLOCK ${_matrix_hz} USART 1)
+		endif()
+	endforeach()
+	if(PUREBOOT_HAS_USART1)
+		pureboot_size_variant(pureboot_usart1 USART 1)
+	endif()
+
+	# The baud axis, whose one size-bearing shape the ladder never picks: a
+	# software UART spins out each bit with _delay_loop_1 while the count
+	# fits a byte and with the 16-bit _delay_loop_2 beyond it, two words more
+	# setup at every one of its five sites — the largest image the
+	# configuration space produces. The ladder default takes the *fastest*
+	# rate a clock reaches, which always lands in the byte, so the wide form
+	# needs the slowest ladder rate against the fastest clock to appear. The
+	# hardware USART has no such shape: its baud is a divisor constant, and
+	# the ladder's U2X solutions are already its larger form.
+	list(GET _matrix_clocks -1 _matrix_top_hz)
+	pureboot_size_variant(pureboot_sw_wide CLOCK ${_matrix_top_hz} BAUD 9600 SERIAL software)
+
+	# One configured deployment end to end — a real board's shape rather
+	# than the stock assumption: the ATmega328P on its shipped 1 MHz fuses,
+	# the software UART on hand-picked pins (TX = PB1, RX = PB5), the ladder
+	# baud (9600). The full protocol suite runs against it, fixture
+	# application included, over the runner's GPIO bridge — proving the
+	# configuration plumbing produces a working loader, not just one that
+	# fits.
+	if(LIBAVR_MCU STREQUAL "atmega328p" AND DEFINED PB_DEVICE)
+		pureboot_size_variant(pureboot_custom CLOCK 1000000 SERIAL software RX pb5 TX pb1)
+		get_target_property(_custom_hz pureboot_custom PUREBOOT_HZ)
+		get_target_property(_custom_baud pureboot_custom PUREBOOT_BAUD)
+		get_target_property(_custom_link pureboot_custom PUREBOOT_LINK)
+		add_executable(pbapp_custom test/pbapp.cpp)
+		target_link_libraries(pbapp_custom PRIVATE libavr)
+		target_compile_definitions(pbapp_custom PRIVATE PUREBOOT_CLOCK_HZ=${_custom_hz}
+		                           PUREBOOT_BAUD=${_custom_baud} PUREBOOT_SOFT_SERIAL PUREBOOT_TX=pb1)
+		add_custom_command(TARGET pbapp_custom POST_BUILD
+		                   COMMAND ${CMAKE_OBJCOPY} -O binary
+		                           $<TARGET_FILE:pbapp_custom> $<TARGET_FILE:pbapp_custom>.bin)
+		add_test(NAME pureboot.custom
+		         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
+		                 ${PB_DEVICE} $<TARGET_FILE:pureboot_custom> ${PUREBOOT_SIM_MCU} ${_custom_hz}
+		                 ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_custom_baud} ${PUREBOOT_EEPROM}
+		                 $<TARGET_FILE:pbapp_custom>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
+		                 ${CMAKE_BINARY_DIR}/pbcustom-work ${_custom_link})
+		set_tests_properties(pureboot.custom PROPERTIES TIMEOUT 180)
+	endif()
+
+	# The second USART, driven for real on one chip: instance selection is
+	# compile-checked everywhere, but only a live session proves the loader
+	# initialized and polls the USART it claims to. The fixture application
+	# banners on the same instance.
+	if(LIBAVR_MCU STREQUAL "atmega644a" AND DEFINED PB_DEVICE)
+		get_target_property(_usart1_hz pureboot_usart1 PUREBOOT_HZ)
+		get_target_property(_usart1_baud pureboot_usart1 PUREBOOT_BAUD)
+		add_executable(pbapp_usart1 test/pbapp.cpp)
+		target_link_libraries(pbapp_usart1 PRIVATE libavr)
+		target_compile_definitions(pbapp_usart1 PRIVATE PUREBOOT_CLOCK_HZ=${_usart1_hz}
+		                           PUREBOOT_BAUD=${_usart1_baud} PUREBOOT_USART=1)
+		add_custom_command(TARGET pbapp_usart1 POST_BUILD
+		                   COMMAND ${CMAKE_OBJCOPY} -O binary
+		                           $<TARGET_FILE:pbapp_usart1> $<TARGET_FILE:pbapp_usart1>.bin)
+		add_test(NAME pureboot.usart1
+		         COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
+		                 ${PB_DEVICE} $<TARGET_FILE:pureboot_usart1> ${PUREBOOT_SIM_MCU} ${_usart1_hz}
+		                 ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_usart1_baud} ${PUREBOOT_EEPROM}
+		                 $<TARGET_FILE:pbapp_usart1>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
+		                 ${CMAKE_BINARY_DIR}/pbusart1-work usart1)
+		set_tests_properties(pureboot.usart1 PROPERTIES TIMEOUT 180)
+	endif()
 endif()

ide/README.md

@@ -1,67 +0,0 @@
-# Atmel Studio
-
-`master` carries `bootloader.atsln`, so this branch does too: `ide/bootloader.atsln`
-builds the loader from the same source Ninja does, to a **byte-identical
-`.text`** — the `tsb_asm` tier in its 512-byte section (`check-flags.py` below
-is what holds the flag sets equal, so the size is Ninja's own). CMake remains
-the build system; the solution is here so the port opens in Studio as its
-predecessor did.
-
-## One project, of four tiers
-
-A `.cppproj` is one binary at one set of flags. `tsb_asm` is the tier that
-occupies the same 512-byte section `master`'s `tsb` project targeted, which is
-the one worth opening in Studio.
-
-The other three tiers (`tsb_pure`, `tsb_tricks`, `tsb_policy`) are not here.
-They differ from `tsb_asm` in their source file, their section size, and — for
-`tsb_policy` — two loop flags; nothing about that is a Studio concern, and what
-they exist to demonstrate is a size gradient only the CMake size tests measure.
-Adding one is a copy of `tsb_asm/tsb_asm.cppproj` in its own directory, with its
-name, its GUID, its source path and its `--section-start` changed (`0x7c00` for
-the 1 KiB tiers), plus four lines in the solution.
-
-`avrdevice` is a project property, so each project gets its own directory:
-Studio builds into `<project dir>/<Configuration>` whatever `OutputDirectory`
-says, and two projects sharing a directory would share one object file.
-
-## Debug keeps `-Os`
-
-Both configurations compile at `-Os`; Debug adds only `-gdwarf-4`. The `.text`
-is therefore identical in both, which is the point — a loader's section is a
-**correctness** bound and not a budget. A debug configuration that silently
-overruns the section is worse than none, and DWARF costs no flash, so the
-optimisation level stays where correctness needs it.
-
-## What Studio needs from the machine
-
-libavr from the **submodule**, found at
-`$(MSBuildProjectDirectory)\..\..\libavr\include` — correct by construction, and
-anchored to the project because a plain relative path resolves against the
-generated makefile's directory (the configuration's output directory), not the
-project's. There is no `LIBAVR_ROOT` escape hatch: a variable exported in a
-shell is invisible to Studio launched from the Start menu, and the failure reads
-as a missing `libavr/libavr.hpp` — which is what the submodule answers.
-
-A GCC 16.1 toolchain registered as flavour `avr-g++-16.1.0`, nothing older
-reaching `-std=c++26`.
-
-## Generating and gating
-
-One generated file is required before the project will load at all, and one
-command checks the flags have not drifted (both from libavr's
-`tools/atmelstudio/`):
-
-```sh
-python libavr/tools/atmelstudio/componentinfo.py \
-    ide/tsb_asm/tsb_asm.componentinfo.xml --device ATmega328P
-python libavr/tools/atmelstudio/check-flags.py \
-    --solution ide/bootloader.atsln --project tsb_asm --target tsb_asm \
-    --compile-commands build/atmega328p-generated/compile_commands.json \
-    --log build/as-tsb_asm.log
-```
-
-Release is what the gate compares — the presets define no debug build, and
-Debug differs from Release only in `-gdwarf-4`.
-
-Legacy (the yazoalfa-era submodules) stays on `master`.

ide/bootloader.atsln

@@ -1,22 +0,0 @@
-
-Microsoft Visual Studio Solution File, Format Version 12.00
-# Atmel Studio Solution File, Format Version 11.00
-VisualStudioVersion = 14.0.23107.0
-MinimumVisualStudioVersion = 10.0.40219.1
-Project("{E66E83B9-2572-4076-B26E-6BE79FF3018A}") = "tsb_asm", "tsb_asm\tsb_asm.cppproj", "{6618D3BE-7EB3-49A2-9113-F128E396FF06}"
-EndProject
-Global
-	GlobalSection(SolutionConfigurationPlatforms) = preSolution
-		Debug|AVR = Debug|AVR
-		Release|AVR = Release|AVR
-	EndGlobalSection
-	GlobalSection(ProjectConfigurationPlatforms) = postSolution
-		{6618D3BE-7EB3-49A2-9113-F128E396FF06}.Debug|AVR.ActiveCfg = Debug|AVR
-		{6618D3BE-7EB3-49A2-9113-F128E396FF06}.Debug|AVR.Build.0 = Debug|AVR
-		{6618D3BE-7EB3-49A2-9113-F128E396FF06}.Release|AVR.ActiveCfg = Release|AVR
-		{6618D3BE-7EB3-49A2-9113-F128E396FF06}.Release|AVR.Build.0 = Release|AVR
-	EndGlobalSection
-	GlobalSection(SolutionProperties) = preSolution
-		HideSolutionNode = FALSE
-	EndGlobalSection
-EndGlobal

ide/tsb_asm/tsb_asm.cppproj

@@ -1,112 +0,0 @@
-<?xml version="1.0" encoding="utf-8"?>
-<Project DefaultTargets="Build" xmlns="http://schemas.microsoft.com/developer/msbuild/2003" ToolsVersion="14.0">
-  <PropertyGroup>
-    <SchemaVersion>2.0</SchemaVersion>
-    <ProjectVersion>7.0</ProjectVersion>
-    <ToolchainName>com.Atmel.AVRGCC8.CPP</ToolchainName>
-    <ProjectGuid>6618d3be-7eb3-49a2-9113-f128e396ff06</ProjectGuid>
-    <avrdevice>ATmega328P</avrdevice>
-    <avrdeviceseries>none</avrdeviceseries>
-    <OutputType>Executable</OutputType>
-    <Language>CPP</Language>
-    <OutputFileName>$(MSBuildProjectName)</OutputFileName>
-    <OutputFileExtension>.elf</OutputFileExtension>
-    <OutputDirectory>$(MSBuildProjectDirectory)\$(Configuration)</OutputDirectory>
-    <AssemblyName>tsb_asm</AssemblyName>
-    <Name>tsb_asm</Name>
-    <RootNamespace>tsb_asm</RootNamespace>
-    <ToolchainFlavour>avr-g++-16.1.0</ToolchainFlavour>
-    <KeepTimersRunning>true</KeepTimersRunning>
-    <OverrideVtor>false</OverrideVtor>
-    <CacheFlash>true</CacheFlash>
-    <ProgFlashFromRam>true</ProgFlashFromRam>
-    <RamSnippetAddress>0x20000000</RamSnippetAddress>
-    <UncachedRange />
-    <preserveEEPROM>true</preserveEEPROM>
-    <OverrideVtorValue>exception_table</OverrideVtorValue>
-    <BootSegment>2</BootSegment>
-    <ResetRule>0</ResetRule>
-    <eraseonlaunchrule>0</eraseonlaunchrule>
-    <EraseKey />
-    <AsfFrameworkConfig>
-      <framework-data xmlns="">
-  <options />
-  <configurations />
-  <files />
-  <documentation help="" />
-  <offline-documentation help="" />
-  <dependencies>
-    <content-extension eid="atmel.asf" uuidref="Atmel.ASF" version="3.52.0" />
-  </dependencies>
-</framework-data>
-    </AsfFrameworkConfig>
-  </PropertyGroup>
-  <PropertyGroup Condition=" '$(Configuration)' == 'Release' ">
-    <ToolchainSettings>
-      <AvrGccCpp>
-        <avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
-        <avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
-        <avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
-        <avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
-        <avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
-        <avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
-        <avrgcccpp.compiler.symbols.DefSymbols>
-          <ListValues>
-            <Value>NDEBUG</Value>
-          </ListValues>
-        </avrgcccpp.compiler.symbols.DefSymbols>
-        <avrgcccpp.compiler.directories.IncludePaths>
-          <ListValues>
-            <Value>$(MSBuildProjectDirectory)\..\..\libavr\include</Value>
-          </ListValues>
-        </avrgcccpp.compiler.directories.IncludePaths>
-        <avrgcccpp.compiler.optimization.level>Optimize for size (-Os)</avrgcccpp.compiler.optimization.level>
-        <avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>
-        <avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>
-        <avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
-        <avrgcccpp.compiler.miscellaneous.OtherFlags>-std=c++26 -Wextra -Werror -mrelax -fno-exceptions -fno-rtti -fno-threadsafe-statics</avrgcccpp.compiler.miscellaneous.OtherFlags>
-        <avrgcccpp.linker.optimization.GarbageCollectUnusedSections>True</avrgcccpp.linker.optimization.GarbageCollectUnusedSections>
-        <avrgcccpp.linker.miscellaneous.LinkerFlags>-mrelax -nostartfiles -Wl,--section-start=.text=0x7e00 -Wl,--defsym=tsb_app=0 -Wl,--pmem-wrap-around=32k</avrgcccpp.linker.miscellaneous.LinkerFlags>
-      </AvrGccCpp>
-    </ToolchainSettings>
-  </PropertyGroup>
-  <PropertyGroup Condition=" '$(Configuration)' == 'Debug' ">
-    <ToolchainSettings>
-      <AvrGccCpp>
-        <avrgcc.common.Device>-mmcu=atmega328p</avrgcc.common.Device>
-        <avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
-        <avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
-        <avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
-        <avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
-        <avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
-        <avrgcccpp.compiler.symbols.DefSymbols>
-          <ListValues>
-            <Value>DEBUG</Value>
-          </ListValues>
-        </avrgcccpp.compiler.symbols.DefSymbols>
-        <avrgcccpp.compiler.directories.IncludePaths>
-          <ListValues>
-            <Value>$(MSBuildProjectDirectory)\..\..\libavr\include</Value>
-          </ListValues>
-        </avrgcccpp.compiler.directories.IncludePaths>
-        <avrgcccpp.compiler.optimization.level>Optimize for size (-Os)</avrgcccpp.compiler.optimization.level>
-        <avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareFunctionsForGarbageCollection>
-        <avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>True</avrgcccpp.compiler.optimization.PrepareDataForGarbageCollection>
-        <avrgcccpp.compiler.warnings.AllWarnings>True</avrgcccpp.compiler.warnings.AllWarnings>
-        <avrgcccpp.compiler.miscellaneous.OtherFlags>-std=c++26 -Wextra -Werror -mrelax -fno-exceptions -fno-rtti -fno-threadsafe-statics -gdwarf-4</avrgcccpp.compiler.miscellaneous.OtherFlags>
-        <avrgcccpp.linker.optimization.GarbageCollectUnusedSections>True</avrgcccpp.linker.optimization.GarbageCollectUnusedSections>
-        <avrgcccpp.linker.miscellaneous.LinkerFlags>-mrelax -nostartfiles -Wl,--section-start=.text=0x7e00 -Wl,--defsym=tsb_app=0 -Wl,--pmem-wrap-around=32k</avrgcccpp.linker.miscellaneous.LinkerFlags>
-      </AvrGccCpp>
-    </ToolchainSettings>
-  </PropertyGroup>
-  <ItemGroup>
-    <Compile Include="..\..\tsb\tsb_asm.cpp">
-      <SubType>compile</SubType>
-      <Link>tsb\tsb_asm.cpp</Link>
-    </Compile>
-  </ItemGroup>
-  <ItemGroup>
-    <Folder Include="tsb" />
-  </ItemGroup>
-  <Import Project="$(AVRSTUDIO_EXE_PATH)\Vs\Compiler.targets" />
-</Project>

oracle/README.md

@@ -38,23 +38,11 @@ avra -I /usr/share/avra tsb-fixedbaud.asm   # after uncommenting .include "m328P
 ```
 
 **500 bytes with every feature** — the proof that ≤512 B and full feature parity
-are simultaneously reachable. The port's four tiers reach it from the other
+are simultaneously reachable. The port's `tsb_asm` tier meets the same bar at
-side, and the gradient between them is the cost of the mechanisms each is
+510 B in the same 512 B section, written in C++ on libavr except the two
-allowed:
+routines whose remaining cost is the calling convention itself (the bounded rx
-
+and the page-store loop); `tsb_tricks` needs no assembly at all at 526 B, and
-| tier | bytes | section | what it is allowed |
+`tsb_pure` stays fully idiomatic at 836 B, both in the 1 KB section.
-|---|---|---|---|
-| oracle | 500 | 512 B | hand-written assembly, the reference |
-| `tsb_asm` | 512 | 512 B | C++ on libavr, two routines in asm |
-| `tsb_tricks` | 528 | 1 KB | no asm; global register variables |
-| `tsb_policy` | 630 | 1 KB | pureboot's rules: no asm, no register variables |
-| `tsb_pure` | 776 | 1 KB | idiomatic libavr throughout |
-
-The two routines `tsb_asm` keeps are the ones whose remaining cost is the
-calling convention itself: the bounded rx and the page-store loop. It fills
-its section exactly, with the same one-bit-time turn-around guard the oracle
-spends six bytes on - every tier implements the whole feature set, which is
-what makes the column a gradient rather than four different loaders.
 
 The oracle targets 20 MHz / 33333 baud; the port targets 16 MHz / 115200 baud
 (what the simavr protocol test drives). Baud and geometry differ, code size and

pureboot/CMakeLists.txt

@@ -0,0 +1,297 @@
+# pureboot as a consumable CMake unit: the per-chip geometry, the default baud
+# ladder, and pureboot_add_loader() — the one way a loader target is created.
+# A downstream project brings its usual libavr setup (the `libavr` target and
+# the LIBAVR_MCU toolchain preset), adds this directory, and states its
+# deployment; every argument is optional (README.md):
+#
+#   add_subdirectory(bootloader/pureboot)
+#   pureboot_add_loader(myboot CLOCK 1000000 SERIAL software TX pb1 RX pb5)
+
+# Per-family geometry, deployment defaults, and the linker wrap the PC modulo
+# needs. The slot is 512 bytes on every chip. The USART flags mirror the
+# hardware inventory the loader's own static asserts check — the plain 644 is
+# the x4 family's one single-USART die (Atmel-2593).
+set(_pb_has_usart 1)
+set(_pb_has_usart1 0)
+if(LIBAVR_MCU MATCHES "^attiny13a?$")
+	set(_pb_flash 1024)
+	set(_pb_wrap "")
+	set(_pb_page 32)
+	set(_pb_hz 9600000)
+	set(_pb_eeprom 64)
+	set(_pb_has_usart 0)
+elseif(LIBAVR_MCU STREQUAL "attiny25")
+	set(_pb_flash 2048)
+	set(_pb_wrap "")
+	set(_pb_page 32)
+	set(_pb_hz 8000000)
+	set(_pb_eeprom 128)
+	set(_pb_has_usart 0)
+elseif(LIBAVR_MCU STREQUAL "attiny45")
+	set(_pb_flash 4096)
+	set(_pb_wrap "")
+	set(_pb_page 64)
+	set(_pb_hz 8000000)
+	set(_pb_eeprom 256)
+	set(_pb_has_usart 0)
+elseif(LIBAVR_MCU STREQUAL "attiny85")
+	set(_pb_flash 8192)
+	set(_pb_wrap -Wl,--pmem-wrap-around=8k)
+	set(_pb_page 64)
+	set(_pb_hz 8000000)
+	set(_pb_eeprom 512)
+	set(_pb_has_usart 0)
+elseif(LIBAVR_MCU MATCHES "^atmega48(a|p|pa)?$")
+	set(_pb_flash 4096)
+	set(_pb_wrap "")
+	set(_pb_page 64)
+	set(_pb_hz 16000000)
+	set(_pb_eeprom 256)
+elseif(LIBAVR_MCU MATCHES "^atmega8a?$" OR LIBAVR_MCU MATCHES "^atmega88(a|p|pa)?$")
+	set(_pb_flash 8192)
+	set(_pb_wrap -Wl,--pmem-wrap-around=8k)
+	set(_pb_page 64)
+	set(_pb_hz 16000000)
+	set(_pb_eeprom 512)
+elseif(LIBAVR_MCU MATCHES "^atmega16a?$" OR LIBAVR_MCU MATCHES "^atmega168(a|p|pa)?$")
+	set(_pb_flash 16384)
+	set(_pb_wrap -Wl,--pmem-wrap-around=16k)
+	set(_pb_page 128)
+	set(_pb_hz 16000000)
+	set(_pb_eeprom 512)
+elseif(LIBAVR_MCU MATCHES "^atmega164(a|p|pa)$")
+	set(_pb_flash 16384)
+	set(_pb_wrap -Wl,--pmem-wrap-around=16k)
+	set(_pb_page 128)
+	set(_pb_hz 16000000)
+	set(_pb_eeprom 512)
+	set(_pb_has_usart1 1)
+elseif(LIBAVR_MCU MATCHES "^atmega32a?$" OR LIBAVR_MCU MATCHES "^atmega328p?$")
+	set(_pb_flash 32768)
+	set(_pb_wrap -Wl,--pmem-wrap-around=32k)
+	set(_pb_page 128)
+	set(_pb_hz 16000000)
+	set(_pb_eeprom 1024)
+elseif(LIBAVR_MCU MATCHES "^atmega324(a|p|pa)$")
+	set(_pb_flash 32768)
+	set(_pb_wrap -Wl,--pmem-wrap-around=32k)
+	set(_pb_page 128)
+	set(_pb_hz 16000000)
+	set(_pb_eeprom 1024)
+	set(_pb_has_usart1 1)
+elseif(LIBAVR_MCU MATCHES "^atmega644(a|p|pa)?$")
+	# 64 KiB is exactly the 16-bit byte space, so plain LPM still reaches
+	# everything and the wire stays byte-addressed. The plain 644 is the
+	# family's one single-USART die.
+	set(_pb_flash 65536)
+	set(_pb_wrap -Wl,--pmem-wrap-around=64k)
+	set(_pb_page 256)
+	set(_pb_hz 16000000)
+	set(_pb_eeprom 2048)
+	if(NOT LIBAVR_MCU STREQUAL "atmega644")
+		set(_pb_has_usart1 1)
+	endif()
+elseif(LIBAVR_MCU MATCHES "^atmega1284p?$")
+	# 128 KiB: wire addresses are words, reads go through ELPM, and the PC's
+	# modulo wrap exceeds what --pmem-wrap-around models.
+	set(_pb_flash 131072)
+	set(_pb_wrap "")
+	set(_pb_page 256)
+	set(_pb_hz 16000000)
+	set(_pb_eeprom 4096)
+	set(_pb_has_usart1 1)
+else()
+	message(FATAL_ERROR "pureboot: no geometry for ${LIBAVR_MCU}")
+endif()
+set(_pb_slot 512)
+math(EXPR _pb_base "${_pb_flash} - ${_pb_slot}")
+math(EXPR _pb_base_hex "${_pb_base}" OUTPUT_FORMAT HEXADECIMAL)
+# Patched-vector chips hand over through the trampoline word below the slot,
+# which is also the slot's own last word — their budget is slot − 2.
+if(LIBAVR_MCU MATCHES "^atmega" AND NOT LIBAVR_MCU MATCHES "^atmega48")
+	set(_pb_app 0)
+	set(_pb_limit ${_pb_slot})
+else()
+	math(EXPR _pb_app "${_pb_base} - 2")
+	math(EXPR _pb_limit "${_pb_slot} - 2")
+endif()
+
+# simavr names its cores after the base dies; the A revisions run on them
+# (the 644PA on the 644P core).
+set(_pb_sim_mcu ${LIBAVR_MCU})
+if(LIBAVR_MCU MATCHES "^atmega(8|16|32|48|88|164|168|644)a$")
+	string(REGEX REPLACE "a$" "" _pb_sim_mcu ${LIBAVR_MCU})
+elseif(LIBAVR_MCU STREQUAL "atmega644pa")
+	set(_pb_sim_mcu atmega644p)
+endif()
+
+# The function runs in its caller's scope, so everything it needs crosses
+# scopes as global properties.
+set_property(GLOBAL PROPERTY PUREBOOT_BASE_HEX ${_pb_base_hex})
+set_property(GLOBAL PROPERTY PUREBOOT_APP ${_pb_app})
+set_property(GLOBAL PROPERTY PUREBOOT_WRAP "${_pb_wrap}")
+set_property(GLOBAL PROPERTY PUREBOOT_DEFAULT_HZ ${_pb_hz})
+set_property(GLOBAL PROPERTY PUREBOOT_HAS_USART ${_pb_has_usart})
+set_property(GLOBAL PROPERTY PUREBOOT_HAS_USART1 ${_pb_has_usart1})
+
+# The port's own build (tests, the size matrix) reads the geometry from the
+# parent scope; a downstream consumer gets the same variables for free.
+set(PUREBOOT_BASE_HEX ${_pb_base_hex} PARENT_SCOPE)
+set(PUREBOOT_PAGE ${_pb_page} PARENT_SCOPE)
+set(PUREBOOT_SLOT ${_pb_slot} PARENT_SCOPE)
+set(PUREBOOT_LIMIT ${_pb_limit} PARENT_SCOPE)
+set(PUREBOOT_EEPROM ${_pb_eeprom} PARENT_SCOPE)
+set(PUREBOOT_DEFAULT_HZ ${_pb_hz} PARENT_SCOPE)
+set(PUREBOOT_HAS_USART ${_pb_has_usart} PARENT_SCOPE)
+set(PUREBOOT_HAS_USART1 ${_pb_has_usart1} PARENT_SCOPE)
+set(PUREBOOT_SIM_MCU ${_pb_sim_mcu} PARENT_SCOPE)
+
+# The fastest standard rate the clock reaches within 2.5 %, by the same
+# best-of-U2X-and-plain divisor search libavr's solve_baud runs, so a default
+# never trips the compile-time error it is checked against. A software build
+# also needs the polled receiver's 100-cycles-a-bit floor: at low clocks the
+# U2X divisor reaches rates the bit-banged sampler cannot.
+function(pureboot_default_baud clock software outvar)
+	foreach(baud 115200 57600 38400 19200 9600)
+		math(EXPR _cycles "${clock} / ${baud}")
+		if(software AND _cycles LESS 100)
+			continue()
+		endif()
+		foreach(divisor 8 16)
+			math(EXPR _step "${divisor} * ${baud}")
+			math(EXPR _n "(${clock} + ${_step} / 2) / ${_step}")
+			if(_n LESS 1 OR _n GREATER 4096)
+				continue()
+			endif()
+			math(EXPR _actual "${clock} / (${divisor} * ${_n})")
+			math(EXPR _delta "${_actual} - ${baud}")
+			if(_delta LESS 0)
+				math(EXPR _delta "-(${_delta})")
+			endif()
+			math(EXPR _error_bp "${_delta} * 10000 / ${baud}")
+			if(_error_bp LESS_EQUAL 250)
+				set(${outvar} ${baud} PARENT_SCOPE)
+				return()
+			endif()
+		endforeach()
+	endforeach()
+	message(FATAL_ERROR "pureboot: no standard baud rate fits a ${clock} Hz clock within 2.5 %")
+endfunction()
+
+# pureboot_add_loader(<name> [CLOCK <hz>] [BAUD <bd>]
+#                     [SERIAL auto|hardware|software] [USART <n>]
+#                     [RX <pin>] [TX <pin>] [TIMEOUT <s>])
+#
+# The loader target plus its flashable images (<name>.hex for a programmer,
+# <name>.bin for --update-loader). The resolved deployment is stamped on the
+# target as PUREBOOT_HZ / PUREBOOT_BAUD / PUREBOOT_LINK (the link spelled
+# usart0, usart1 or sw:<RX>,<TX>) — what a test harness speaks to it with.
+function(pureboot_add_loader name)
+	cmake_parse_arguments(PB "" "CLOCK;BAUD;SERIAL;USART;RX;TX;TIMEOUT" "" ${ARGN})
+	if(PB_UNPARSED_ARGUMENTS)
+		message(FATAL_ERROR "pureboot_add_loader(${name}): unknown arguments ${PB_UNPARSED_ARGUMENTS}")
+	endif()
+	get_property(_hz GLOBAL PROPERTY PUREBOOT_DEFAULT_HZ)
+	get_property(_base_hex GLOBAL PROPERTY PUREBOOT_BASE_HEX)
+	get_property(_app GLOBAL PROPERTY PUREBOOT_APP)
+	get_property(_wrap GLOBAL PROPERTY PUREBOOT_WRAP)
+	get_property(_usart GLOBAL PROPERTY PUREBOOT_HAS_USART)
+	get_property(_usart1 GLOBAL PROPERTY PUREBOOT_HAS_USART1)
+
+	if(NOT PB_CLOCK)
+		set(PB_CLOCK ${_hz})
+	endif()
+	if(NOT PB_TIMEOUT)
+		set(PB_TIMEOUT 8)
+	endif()
+	if(NOT PB_SERIAL)
+		set(PB_SERIAL auto)
+	endif()
+	if(DEFINED PB_USART AND PB_SERIAL STREQUAL "software")
+		message(FATAL_ERROR "pureboot_add_loader(${name}): USART ${PB_USART} contradicts SERIAL software")
+	endif()
+	if(DEFINED PB_USART)
+		set(PB_SERIAL hardware)
+	elseif(PB_SERIAL STREQUAL "hardware")
+		set(PB_USART 0)
+	endif()
+
+	set(_serial_defines "")
+	if(PB_SERIAL STREQUAL "hardware")
+		if(PB_USART EQUAL 1 AND NOT _usart1)
+			message(FATAL_ERROR "pureboot_add_loader(${name}): ${LIBAVR_MCU} has no USART1")
+		elseif(NOT _usart)
+			message(FATAL_ERROR "pureboot_add_loader(${name}): ${LIBAVR_MCU} has no hardware USART")
+		endif()
+		set(_serial_defines PUREBOOT_USART=${PB_USART})
+		set(_link usart${PB_USART})
+	else()
+		if(PB_SERIAL STREQUAL "auto")
+			if(_usart AND (PB_RX OR PB_TX))
+				message(WARNING "pureboot_add_loader(${name}): RX/TX apply to the software UART, "
+				        "which auto does not pick on ${LIBAVR_MCU} — SERIAL software to force it")
+			endif()
+			if(_usart)
+				set(_link usart0)
+			else()
+				set(PB_SERIAL software)
+			endif()
+		endif()
+		if(PB_SERIAL STREQUAL "software")
+			if(NOT PB_RX)
+				set(PB_RX pb0)
+			endif()
+			if(NOT PB_TX)
+				set(PB_TX pb1)
+			endif()
+			foreach(_pin ${PB_RX} ${PB_TX})
+				if(NOT _pin MATCHES "^p[a-h][0-7]$")
+					message(FATAL_ERROR "pureboot_add_loader(${name}): pin '${_pin}' is not of the form pb1")
+				endif()
+			endforeach()
+			set(_serial_defines PUREBOOT_SOFT_SERIAL PUREBOOT_RX=${PB_RX} PUREBOOT_TX=${PB_TX})
+			# sw:<RX>,<TX> as port letter and bit, upcased.
+			string(SUBSTRING ${PB_RX} 1 2 _rx_pin)
+			string(SUBSTRING ${PB_TX} 1 2 _tx_pin)
+			string(TOUPPER "sw:${_rx_pin},${_tx_pin}" _link)
+			string(REPLACE "SW" "sw" _link ${_link})
+		endif()
+	endif()
+	if(NOT PB_BAUD)
+		if(PB_SERIAL STREQUAL "software")
+			pureboot_default_baud(${PB_CLOCK} 1 PB_BAUD)
+		else()
+			pureboot_default_baud(${PB_CLOCK} 0 PB_BAUD)
+		endif()
+	endif()
+
+	set(_defines PUREBOOT_CLOCK_HZ=${PB_CLOCK} PUREBOOT_BAUD=${PB_BAUD} PUREBOOT_TIMEOUT=${PB_TIMEOUT}
+	    ${_serial_defines})
+
+	add_executable(${name} ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/pureboot.cpp)
+	target_link_libraries(${name} PRIVATE libavr)
+	target_compile_definitions(${name} PRIVATE ${_defines})
+	# Codegen shaping for the loader TU only, worth 14–36 B depending on the
+	# chip. At -Os GCC otherwise rewrites the byte-stream loops' counters into
+	# end-pointer forms that cost registers (-fno-ivopts,
+	# -fno-split-wide-types), leaves register pressure on the table with the
+	# default allocator (-fira-algorithm=priority), and keeps loop-invariant
+	# immediates and expression temporaries in registers
+	# (-fno-move-loop-invariants, -fno-tree-ter) — but every loop body here
+	# contains a call, so a register held across it costs more than the
+	# load-immediate it saves.
+	target_compile_options(${name} PRIVATE
+	    -fno-ivopts -fira-algorithm=priority -fno-move-loop-invariants -fno-tree-ter -fno-split-wide-types)
+	target_link_options(${name} PRIVATE -nostartfiles -Wl,--section-start=.text=${_base_hex}
+	                    -Wl,--defsym=pureboot_app=${_app} ${_wrap})
+	add_custom_command(TARGET ${name} POST_BUILD COMMAND ${CMAKE_SIZE} $<TARGET_FILE:${name}>)
+	# The ELF is a container, never flashed: .hex for a programmer, .bin (the
+	# slot's bare bytes) for --update-loader.
+	add_custom_command(TARGET ${name} POST_BUILD
+	                   COMMAND ${CMAKE_OBJCOPY} -O ihex -R .eeprom
+	                           $<TARGET_FILE:${name}> $<TARGET_FILE:${name}>.hex
+	                   COMMAND ${CMAKE_OBJCOPY} -O binary -R .eeprom
+	                           $<TARGET_FILE:${name}> $<TARGET_FILE:${name}>.bin)
+	set_target_properties(${name} PROPERTIES PUREBOOT_HZ ${PB_CLOCK} PUREBOOT_BAUD ${PB_BAUD}
+	                      PUREBOOT_LINK ${_link})
+endfunction()

pureboot/README.md

@@ -0,0 +1,346 @@
+# pureboot
+
+A serial bootloader on [libavr](https://git.blackmark.me/avr/libavr), pure by
+constraint: one C++ source, no inline assembly, no global register variables
+(attributes and compiler flags allowed), **512 bytes on every chip libavr
+targets — all 37**. The device speaks primitives; every composite — verify,
+erase, reset-vector surgery, updating the loader itself — lives in the host
+tool (`pureboot.py`).
+
+The image is **position-independent**: control flow is PC-relative, the
+read/write paths take wire addresses, the write guard protects the slot the
+code is *running* in (from the runtime return address), the info block is
+addressed from that same anchor, and the application jump is an indirect call
+to an absolute entry. The identical binary therefore runs from any slot with
+every command intact, which makes pureboot **its own staging loader**: the
+host installs the same binary one slot below the resident, jumps into it, and
+lets it rewrite the resident.
+
+## Chips
+
+Sizes are the default configuration: the hardware USART0 at 115200 8N1 on a
+16 MHz crystal, or the software UART on RX = PB0 / TX = PB1 at 57600 8N1 on
+the tinies' RC oscillator (9.6 MHz on the t13s, 8 MHz above). Every axis moves
+per build — see *Configuration*; the largest image any of them produces is a
+software UART at a slow baud, which on the 1284s is 494 B, the tightest fit in
+the whole matrix at 18 B spare.
+
+| Chip | Flash | Loader at | Link | Size |
+|---|---|---|---|---|
+| ATtiny13, ATtiny13A † | 1 KiB | 0x0200 | software | 416 B |
+| ATtiny25 † | 2 KiB | 0x0600 | software | 420 B |
+| ATtiny45 † | 4 KiB | 0x0e00 | software | 424 B |
+| ATtiny85 † | 8 KiB | 0x1e00 | software | 424 B |
+| ATmega8, 8A | 8 KiB | 0x1e00 | USART0 | 396 B |
+| ATmega16, 16A | 16 KiB | 0x3e00 | USART0 | 400 B |
+| ATmega32, 32A | 32 KiB | 0x7e00 | USART0 | 400 B |
+| ATmega48, 48A, 48P, 48PA † | 4 KiB | 0x0e00 | USART0 | 414 B |
+| ATmega88, 88A, 88P, 88PA | 8 KiB | 0x1e00 | USART0 | 434 B |
+| ATmega168, 168A, 168P, 168PA | 16 KiB | 0x3e00 | USART0 | 438 B |
+| ATmega328, 328P | 32 KiB | 0x7e00 | USART0 | 438 B |
+| ATmega164A, 164P, 164PA | 16 KiB | 0x3e00 | USART0 | 438 B |
+| ATmega324A, 324P, 324PA | 32 KiB | 0x7e00 | USART0 | 438 B |
+| ATmega644, 644A, 644P, 644PA | 64 KiB | 0xfe00 | USART0 | 432 B |
+| ATmega1284, 1284P | 128 KiB | 0x1fe00 | USART0 | 478 B |
+
+† No hardware boot section: the host patches the reset vector, and the budget
+is 510 bytes, since the slot's last word is the trampoline.
+
+The 1284s are the heaviest because they alone carry the far-flash machinery —
+ELPM reads, RAMPZ page commands, a word-addressed wire.
+
+The software UART enables the RX pull-up; TX idles high. All multi-byte wire
+quantities are little-endian.
+
+## Configuration
+
+Every deployment axis is a build parameter of `pureboot_add_loader()` (in
+`pureboot/CMakeLists.txt`) — the one way a loader target is created, by this
+repo's build and by a downstream project alike:
+
+| Argument | Meaning | Default |
+|---|---|---|
+| `CLOCK <hz>` | the clock the board runs | 16 MHz megas, 8 MHz t25/45/85, 9.6 MHz t13s |
+| `BAUD <bd>` | the wire rate | the ladder below |
+| `SERIAL auto\|hardware\|software` | the link backend | `auto`: the hardware USART where the chip has one |
+| `USART <n>` | the USART instance (x4 megas carry two) | 0 |
+| `RX <pin>`, `TX <pin>` | software-UART pins | `pb0`, `pb1` |
+| `TIMEOUT <s>` | the activation window | 8 |
+
+The default baud is the fastest of 115200/57600/38400/19200/9600 the clock
+reaches within 2.5 % — the same U2X-included divisor search libavr's baud
+solver runs — and on a software build additionally within the polled
+receiver's 100-cycles-a-bit floor. Whatever is picked or overridden is
+re-checked in the compile: an infeasible combination, or a USART the chip does
+not have, fails with a named static assert.
+
+A downstream project brings its usual libavr setup (the `libavr` target, the
+chip via the `LIBAVR_MCU` toolchain preset), consumes this directory, and
+states its deployment — an ATmega328P on its shipped 1 MHz fuses with the
+software UART on hand-picked pins, say:
+
+```cmake
+FetchContent_Declare(bootloader GIT_REPOSITORY git@git.blackmark.me:avr/bootloader.git GIT_TAG main)
+FetchContent_MakeAvailable(bootloader)
+add_subdirectory(${bootloader_SOURCE_DIR}/pureboot pureboot)
+
+pureboot_add_loader(myboot CLOCK 1000000 SERIAL software TX pb1 RX pb5)
+```
+
+The function emits the ELF plus `myboot.hex` (the programmer artifact) and
+`myboot.bin` (the self-update image), prints the size, and stamps the resolved
+deployment on the target as the `PUREBOOT_HZ`, `PUREBOOT_BAUD` and
+`PUREBOOT_LINK` properties — what a flashing script or test harness needs to
+speak to the build. This exact deployment runs the full protocol suite in CI
+(`pureboot.custom`).
+
+## Activation
+
+Reset enters the loader (BOOTRST on the boot-sectioned megas, the patched
+reset vector elsewhere) — except a watchdog reset, which hands straight to the
+application, since the application owns its watchdog and must clear WDRF
+itself.
+
+The host then knocks `p` then `b`, each awaited byte under a fresh activation
+window; any other byte is discarded and awaited again, so line noise can delay
+the loader but never lock it. A window expiring on an idle line boots the
+application.
+
+The window is a compile-time constant (`TIMEOUT`, 8 s by default), so the whole
+EEPROM belongs to the application — pureboot keeps no state of its own.
+Re-timing a deployed loader is a self-update with a re-timed build.
+
+## Session
+
+After the knock the loader stays in its command loop until `J` jumps away or
+the chip resets. Before reading each command it waits for any pending EEPROM
+write and sends the prompt `+` (0x2b), which is therefore also the previous
+command's completion ack. A session is: await `+`, send a command, read its
+reply, repeat.
+
+On chips whose flash exceeds 64 KiB (the 1284s — info-block flag bit 1) the
+`R`/`W` flash addresses are **word** addresses; everywhere else they are byte
+addresses (the 644s' 64 KiB is exactly the 16-bit byte space). EEPROM
+addresses and all counts are bytes.
+
+| Cmd | Arguments | Reply |
+|---|---|---|
+| `b` | — | the 12-byte info block |
+| `R` | addr16, n8 | n flash bytes (n = 0 means 256) |
+| `W` | addr16, then one page of data | — (completion = next prompt) |
+| `r` | addr16, n8 | n EEPROM bytes (n = 0 means 256) |
+| `w` | addr16, n8, then n data bytes | `+` per byte, sent once its write has begun |
+| `F` | — | 4 bytes: low fuse, lock, extended fuse, high fuse |
+| `J` | word address (16-bit) | `+`, then execution continues there |
+| other | — | ignored; the loop re-prompts (send a junk byte, await `+`, to resync) |
+
+`W` streams exactly one page-aligned SPM page (size from the info block) into
+the buffer, then erases and programs — except pages inside the 512-byte slot
+the loader is *running* in, which are drained and left alone, so a broken host
+cannot brick the running copy and a staged copy may rewrite the resident.
+
+The loader never clears the SPM buffer before a fill, so **one `W` may program
+the wrong bytes, and the host is what fixes it**. The buffer is write-once per
+word until cleared, and two things leave words in it: a refused page, and —
+where SPM runs from anywhere, the tinies and the m48s — an application that
+self-programmed before entering. The next `W` takes those stale words and
+clears them, since a page write auto-erases the buffer (§26.2.1; §19.2 on the
+tinies), so repeating it programs correctly. The host therefore verifies every
+page it writes and rewrites what comes back wrong (three retries, then it
+stops).
+
+`w` is host-paced: send the next byte only after the previous byte's `+`. `F`
+returns the bytes in the hardware's Z order; on a chip without an extended
+fuse byte that slot carries no meaning. Fuse *writing* does not exist — SPM
+reaches flash and boot lock bits only.
+
+`J` is the one control-transfer primitive: it runs the application (word 0 or
+the trampoline word, both known from the info block) and moves between loader
+copies during a self-update. A jump to a slot's base re-enters that copy's own
+startup, which must then be knocked afresh.
+
+The info block (`b`):
+
+| Offset | Content |
+|---|---|
+| 0–2 | `'P'`, `'B'`, pureboot version (3) |
+| 3–5 | device signature |
+| 6 | SPM page size in bytes (0 means 256) |
+| 7–8 | loader base — application flash ends here (a word address when bit 1 is set) |
+| 9–10 | EEPROM size |
+| 11 | bit 0: host must patch the reset vector (no hardware boot section); bit 1: flash wire addresses are word addresses |
+
+## Version
+
+The info block's third byte is the **pureboot version** — the loader's one
+identity number, and the only way to tell what a deployed loader is. Nothing
+else is numbered: the wire protocol has no version, a pureboot version implies
+it, and the host tool holds that map. The tool states the window of loader
+versions it speaks (`OLDEST_LOADER`/`NEWEST_LOADER` in `pureboot.py`), and a
+version that changes the protocol becomes the new floor there. None has so
+far: 1 through 3 speak the identical session. A loader newer than the tool is
+refused by name rather than decoded on the assumption that nothing moved.
+
+The tool carries its own version, free to drift; `--version` prints it and the
+window.
+
+## Deployment
+
+The build leaves three artifacts per chip. The ELF is a container for the
+tests and objcopy, never flashed. The **.hex is the programmer artifact**: it
+carries its own addresses and lands the loader in its top slot, touching
+nothing else. The **.bin is the self-update image** — the slot's bare bytes.
+
+**Boot-sectioned megas**: program the loader at `flash − 512` with an external
+programmer. Every such mega has a BOOTSZ step whose boot section is exactly
+the 512-byte slot — the second-smallest step on the 8 KiB and 16 KiB chips,
+the smallest on the 32 KiB ones — so the ATmega328P profiles below apply to
+every one of them with its own addresses; the per-chip BOOTSZ ladders live in
+the host tool (`BOOT_FUSE`).
+
+The **644s and 1284s** are the geometry's sweet spot: their smallest boot
+section (512 words = 1 KiB) is exactly *two* slots, so the resident and its
+staging slot both live inside the minimum section. Self-update needs no fuse
+step up, and the standalone profile does not exist — reset lands one erased
+slot below the loader (0xfc00 / 0x1fc00) and walks up into it.
+
+ATmega328P profiles (addresses for its 32 KiB):
+
+| BOOTSZ | BOOTRST | Behavior |
+|---|---|---|
+| 256 words (512 B) | programmed | *Standalone*: reset always enters the loader; **self-update impossible** (the staging slot lies outside the boot section, where SPM is disabled). |
+| 512 words (1 KB) | unprogrammed | *Self-update, app-first*: reset always boots the application, which owns all 31.5 KB and must offer its own jump to 0x7e00 to reach the loader (a virgin chip reaches it by reset across erased flash). Updates are power-fail-safe except mid-rewrite of the resident slot itself (no reset path leads to the staging copy then). |
+| 512 words (1 KB) | programmed | *Self-update, loader-first*: reset lands at 0x7c00 — the staging slot, normally erased, so execution walks up into the loader; during an update it is the staging copy itself, so a mid-rewrite power loss recovers by reset. The loss windows move to the staging install/retire page writes instead (page-write scale). The host keeps `[0x7c00, 0x7e00)` clear of application data (`--force` overrides). |
+
+Applications are flashed unmodified here — word 0 stays the application's own
+reset vector, and the hand-over jumps to 0.
+
+**Patched-vector chips — the tinies and the m48s** (no boot section; the m48s'
+SPM runs from the entire flash, Atmel-8271 §26): program the loader at
+`flash − 512`; erased flash below it walks up into the loader, so a virgin
+chip activates. Flashing an application then takes reset-vector surgery: word
+0 becomes an `rjmp` to the loader base, and the application's own entry is
+re-encoded as a trampoline `rjmp` in the word just below the loader
+(`base − 2`, where the hand-over jumps). Every other vector stays the
+application's. The patched page 0 and the trampoline page are written *first*
+and an erase runs top-down, so from the first write on an interruption still
+resets into the loader.
+
+A .bin programmed at address 0 by mistake is dead weight on a boot-sectioned
+mega (SPM only executes from the boot section — reflash the .hex), but *runs*
+on a patched-vector chip, and the ordinary `--update-loader` flow re-homes it
+into the top slot from there (`pureboot.rehome`).
+
+## Updating the loader
+
+`pureboot.py --update-loader new_pureboot.bin` replaces the resident loader
+with any pureboot build — a re-timed window, a newer version — using the
+loader itself as its own staging loader. The image is the loader's own 512
+bytes as a raw binary, or the Intel HEX the build emits beside it.
+
+The preflight refuses an image built for another chip: the info block embedded
+in every pureboot binary (signature, page size, loader base, EEPROM size,
+flags) must match the device's own, and the error names both. Die revisions
+share their base signature and geometry, so their images are interchangeable —
+as the silicon is.
+
+1. The staging slot `[base−512, base)` is saved to a host-side state file (on
+   the 1 KB tiny13s that is the whole application, vectors included).
+2. The resident installs the update image there. On the patched-vector chips
+   the host composes the slot's last word as a jump to the resident base, so
+   even an abandoned staging copy times out into a loader. A loader already
+   sitting whole in the staging slot is left as the staging copy instead —
+   rewriting it would only meet its own running-slot guard.
+3. `J` enters the staging copy, which rewrites the resident slot. Where a
+   patched reset vector routes through the resident, the host first re-aims
+   word 0 at the staging copy, so a power loss mid-rewrite still resets into a
+   loader; on the tiny13s the staging slot carries the reset vector itself.
+4. `J` enters the new resident, which restores the staging slot's saved
+   content, and the state file is discarded.
+
+Every phase is idempotent and keyed off the actual flash state, so re-running
+the same command after any interruption resumes and completes. The state file
+carries the only bytes not recoverable from the device; losing it mid-update
+still completes the update, and the staging region comes back by reflashing
+the application. A boot-sectioned mega needs its fuses for the preflight — read
+from the device, or supplied with `--assume-fuses` where reading is impossible
+(simulators).
+
+## Host tool
+
+`pureboot.py` — Python 3, standard library only. The port layer is the one
+platform-specific part: termios drives any tty on POSIX (a USB adapter as well
+as a simavr pty), the Win32 serial API through `ctypes` drives a COM port on
+Windows (`--port COM6`; the `\\.\` form for two-digit ports is supplied by the
+tool). Opening the port asserts DTR and RTS on both, so a board that wires DTR
+to reset gets its reset pulse and opens the activation window by itself.
+
+    pureboot.py --port /dev/ttyUSB0 --baud 57600 \
+        --info --fuses --flash app.hex
+
+Operations run in a fixed order within one session: info, fuses, loader
+update, flash (erase / program / read / verify), EEPROM (the same) — then the
+loader hands over to the application. `--stay` keeps the session alive
+instead, and a later invocation reconnects into it. `--flash` and `--eeprom`
+verify by read-back unless `--no-verify`, and a flash page that reads back
+wrong is rewritten up to three times before the run stops (see `W` above).
+`--verify-flash` only reports. Images are raw binary, or Intel HEX by
+extension. `--force` overrides the refusable safety checks — today, flashing
+application data into a mega's reset walk region.
+
+Readouts come one fact per line: `--info` decodes the info block field by
+field, `--fuses` each fuse byte plus, on a boot-sectioned mega, its decoded
+meaning. Transfers that take wire time draw a transient progress bar on stderr
+when it is a tty. `-v`/`--verbose` adds the decisions as they happen: knock
+counts, the programming plan, update state handling and per-phase page counts.
+
+## Tests
+
+`tools/check.sh` runs every chip's workflow (`--full` adds the reflect-mode
+builds of libavr's spot set; `tools/make_presets.py` regenerates the presets).
+Per chip preset, `ctest` runs:
+
+- `pureboot.size` — the 510-byte (patched-vector) / 512-byte budget;
+- `pureboot_*.size` — the size matrix: the serial backends × the clock ladder
+  (1/8/16 MHz; the t13s' own RC menu), the USART1 instance across that same
+  ladder on the x4 chips, and `pureboot_sw_wide`, the slowest ladder rate at
+  the fastest clock — where a software UART's per-bit spin outgrows its
+  one-register delay loop and takes the 16-bit one. That is the largest image
+  the configuration space produces, and a shape the ladder default (always the
+  *fastest* rate a clock reaches) never picks. Pins are immediate operands and
+  the timeout is a constant: neither is an axis;
+- `pureboot.pi` — the position-independence lint: no absolute `jmp`/`call`, the
+  info block within the image's first 256 bytes;
+- `pureboot.planner` — the host tool's pure logic: programming orders and their
+  recovery properties, the surgery, the staging composition, the boot-fuse
+  decode, the update preflight over synthetic fuse bytes, and the repairing
+  verify against a fake device;
+- `pureboot.protocol` — end to end against a simavr device
+  (`test/pureboot_device.c`: a hardware USART as a pty, or a cycle-timed
+  GPIO⇄pty bridge for a software-UART build, plus the SPM/NVM module simavr's
+  tiny cores lack) driven by the real host tool through knock-from-reset,
+  program + verify of both memories, session reconnect, an external reset
+  through the patched vector, and the hand-over to a fixture application whose
+  banner proves the launch — cross-checked against the simulator's
+  ground-truth memory dumps and an independent decode of the surgery;
+- `pureboot.reloc` — the identical image one slot below the resident serves the
+  complete command set from there;
+- `pureboot.rehome` (t85) — a loader programmed at address 0 or in the staging
+  slot re-homes into the top slot through the ordinary update flow;
+- `pureboot.custom` (328P) — the configuration example's 1 MHz software-serial
+  build driving the full protocol suite, proving the plumbing produces a
+  working loader and not just one that fits;
+- `pureboot.usart1` (644A) — the same suite over the second hardware USART:
+  instance selection is compile-checked everywhere, but only a live session
+  proves the loader polls the USART it claims;
+- `pureboot.dirty` (328P) — entering the loader from a running application over
+  an SPM buffer it deliberately dirtied, the case the loader declines to guard:
+  a bare verify must see the corruption and the repairing verify must fix it in
+  one rewrite. Hardware forbids the state here, but simavr dispatches SPM from
+  anywhere, which is what makes the path constructible;
+- `pureboot.update` — the full `--update-loader` flow, then every power-fail
+  phase: the device is killed mid-write, restarted from its flash dump, and a
+  re-run must complete the update with the application intact.
+
+`size`, `pi` and `planner` are host logic and run anywhere; the
+simulator-driven targets need simavr and a pty, so they are POSIX-only.

pureboot/pureboot.cpp

@@ -0,0 +1,457 @@
+// pureboot — a serial bootloader on libavr: one C++ source, no inline
+// assembly, no global register variables, 512 bytes on every chip libavr
+// targets. The device speaks primitives; every composite (verify, erase,
+// reset-vector surgery, self-update) lives in the host tool. Protocol,
+// deployment and configuration: README.md next to this file.
+//
+// The image is position-independent — PC-relative control flow, wire
+// addresses in, the write guard and the info block both anchored on the
+// runtime return address — so the identical binary runs from any slot. That
+// is what makes a copy one slot below able to rewrite the resident one, and
+// every change here has to keep it (test/check_pi.py).
+
+#include <libavr/libavr.hpp>
+
+using namespace avr::literals;
+namespace spm = avr::spm;
+namespace ee = avr::eeprom;
+
+namespace pureboot {
+namespace {
+
+// Purely polled: every interrupt guard folds to nothing.
+constexpr auto off = avr::irq::guard_policy::unused;
+
+constexpr std::uint8_t ack = '+';
+
+// Deployment parameters come from the build (pureboot_add_loader()). The
+// signature is not one of them: the chip database is the only universal
+// source — a tiny13A cannot read its own signature row from code.
+#if !defined(PUREBOOT_CLOCK_HZ) || !defined(PUREBOOT_BAUD)
+#error \
+    "PUREBOOT_CLOCK_HZ and PUREBOOT_BAUD select this build's clock and baud — create loader targets with pureboot_add_loader() (README.md)"
+#endif
+
+using dev = avr::device<{.clock = avr::hertz_t{PUREBOOT_CLOCK_HZ}}>;
+constexpr avr::baud_t wire_baud{PUREBOOT_BAUD};
+
+// The watchdog reset flag's home: MCUSR, or the classic megas' MCUCSR.
+consteval std::int16_t wdrf_field()
+{
+	auto reg = std::string_view{avr::hw::db.regs[static_cast<std::size_t>(avr::power::detail::reset_reg())].name};
+	return avr::hw::db.field_index(reg, "WDRF");
+}
+
+// The loader owns the top 512 bytes; a staging copy goes in the slot below.
+// Chips without a hardware boot section — the tinies and the m48s, whose SPM
+// runs from anywhere (Atmel-8271 §26) — keep the application's relocated
+// reset vector in the word under the slot.
+constexpr std::uint16_t slot_bytes = 512;
+constexpr std::uint32_t base = spm::flash_bytes - slot_bytes;
+constexpr std::uint16_t page = spm::page_bytes;
+constexpr bool boot_section = avr::hw::curated::has_boot_section();
+
+// Past 64 KiB a byte address no longer fits the wire's 16 bits, so flash
+// addresses there are word addresses ('J' always was one). A slot is 256 of
+// those — one value of a wire address's high byte, where 512 bytes span two.
+constexpr bool word_flash = spm::flash_bytes > 65536;
+constexpr std::uint16_t wire_base =
+    word_flash ? static_cast<std::uint16_t>(base / 2) : static_cast<std::uint16_t>(base);
+
+// A compile-time window, so the whole EEPROM belongs to the application;
+// re-timing a deployed loader is a self-update with a re-timed build.
+#if !defined(PUREBOOT_TIMEOUT)
+#define PUREBOOT_TIMEOUT 8
+#endif
+constexpr std::uint8_t timeout_seconds = PUREBOOT_TIMEOUT;
+
+// The loader's one identity number. The protocol carries none of its own —
+// a version implies it, and the host tool holds that map (README.md).
+constexpr std::uint8_t version = 3;
+
+// The 'b' reply, byte for byte (layout: README.md). Flash-resident because
+// no crt copies a .data image — and flash_table's storage carries the word
+// alignment 'b' needs to halve the address on the large chips.
+inline constexpr avr::flash_table<std::array<std::uint8_t, 12>{
+    'P', 'B', version, avr::hw::db.signature[0], avr::hw::db.signature[1], avr::hw::db.signature[2],
+    static_cast<std::uint8_t>(page), // 0 means 256
+    wire_base & 0xff, wire_base >> 8, avr::hw::db.mem.eeprom_size & 0xff, avr::hw::db.mem.eeprom_size >> 8,
+    static_cast<std::uint8_t>((boot_section ? 0 : 1) | (word_flash ? 2 : 0)), // patch-vector, word-addressed
+}>
+    info_data;
+
+// The serial link, per the build's PUREBOOT_USART / PUREBOOT_SOFT_SERIAL,
+// defaulting to the chip's USART0 where it has one. The software receiver is
+// the polled one: the vector table belongs to the application. Templates on
+// the clock, so only the selected backend instantiates. pending() is the
+// cheap line test the activation window polls; drain() holds until the last
+// frame is off the wire, so a hand-over cannot let the target's re-init clip
+// the ack.
+#if defined(PUREBOOT_SOFT_SERIAL) && defined(PUREBOOT_USART)
+#error "PUREBOOT_SOFT_SERIAL and PUREBOOT_USART select opposing serial backends"
+#endif
+#if !defined(PUREBOOT_RX)
+#define PUREBOOT_RX pb0
+#endif
+#if !defined(PUREBOOT_TX)
+#define PUREBOOT_TX pb1
+#endif
+#if defined(PUREBOOT_USART)
+constexpr char usart_digit = '0' + PUREBOOT_USART;
+#else
+constexpr char usart_digit = '0';
+#endif
+
+template <avr::hertz_t C>
+struct hardware_link {
+	using uart = avr::uart::usart<usart_digit, C, {.baud = wire_baud, .max_baud_error = 2.5_pct}>;
+
+	// The compiled idle poll: lds UCSR0A (2), sbrc skipping the exit (2),
+	// sbiw + sbci + sbci + brne (6).
+	static constexpr std::uint8_t poll_cycles = 10;
+
+	static void init()
+	{
+		avr::init<uart>();
+	}
+
+	static bool pending()
+	{
+		return uart::rx_ready();
+	}
+
+	static std::uint8_t rx()
+	{
+		return uart::read_blocking();
+	}
+
+	static void tx(std::uint8_t byte)
+	{
+		uart::write(byte);
+	}
+
+	static void drain()
+	{
+		uart::drain();
+	}
+};
+
+template <avr::hertz_t C>
+struct software_link {
+	using rx_t = avr::uart::software_rx_polled<C, avr::PUREBOOT_RX, wire_baud>;
+	using tx_t = avr::uart::software_tx<C, avr::PUREBOOT_TX, wire_baud>;
+
+	// The compiled idle poll: sbis skipping the exit (2), sbiw + sbci +
+	// sbci + brne (6).
+	static constexpr std::uint8_t poll_cycles = 8;
+
+	static void init()
+	{
+		avr::init<rx_t, tx_t>();
+	}
+
+	static bool pending()
+	{
+		return rx_t::start_pending();
+	}
+
+	static std::uint8_t rx()
+	{
+		return rx_t::template read_blocking<off>();
+	}
+
+	static void tx(std::uint8_t byte)
+	{
+		tx_t::template write<off>(byte);
+	}
+
+	static void drain()
+	{
+		// The software transmitter returns only after the stop bit.
+	}
+};
+
+#if defined(PUREBOOT_USART)
+static_assert(avr::uart::has_usart<usart_digit>(), "PUREBOOT_USART selects a hardware USART this chip does not have");
+using link = hardware_link<dev::clock>;
+#elif defined(PUREBOOT_SOFT_SERIAL)
+using link = software_link<dev::clock>;
+#else
+using link =
+    std::conditional_t<avr::uart::has_usart<usart_digit>(), hardware_link<dev::clock>, software_link<dev::clock>>;
+#endif
+
+// The application's entry, pinned by the linker (--defsym): word 0 on a
+// boot-sectioned mega, the trampoline at base − 2 elsewhere. Reaching it must
+// not depend on where this copy runs, so the jump goes through a pointer, and
+// [[gnu::noipa]] keeps the constant from folding back into a relative call.
+extern "C" [[noreturn]] void pureboot_app();
+
+[[gnu::noipa, noreturn]] void jump(void (*target)())
+{
+	target();
+	__builtin_unreachable();
+}
+
+[[gnu::noinline, noreturn]] void run_app()
+{
+	jump(pureboot_app);
+}
+
+// The window as one 32-bit countdown, divided by the backend's counted
+// poll-loop cycles. Whole seconds is all it promises.
+consteval std::uint32_t window_polls()
+{
+	return timeout_seconds * static_cast<std::uint32_t>(dev::clock.hz / link::poll_cycles);
+}
+
+bool pending_before_deadline()
+{
+	std::uint32_t polls = window_polls();
+	do {
+		if (link::pending())
+			return true;
+	} while (--polls);
+	return false;
+}
+
+// A knock byte under the deadline: an idle window means no host, so the
+// application runs.
+std::uint8_t rx_deadline()
+{
+	if (!pending_before_deadline())
+		run_app();
+	return link::rx();
+}
+
+// Inlined: read across a call, the first byte strands in a call-saved
+// register the caller has to push and pop.
+[[gnu::always_inline]] inline std::uint16_t rx16()
+{
+	std::uint16_t low = link::rx();
+	return static_cast<std::uint16_t>(low | (link::rx() << 8));
+}
+
+// The wire's byte pair as the word it is — AVR is little-endian too, so the
+// cast is the identity a shift-and-or spelling makes the compiler rediscover.
+// Callers read into named variables first: the wire order is a sequence of
+// reads, not an argument order.
+[[gnu::always_inline]] inline std::uint16_t word_of(std::array<std::uint8_t, 2> pair)
+{
+	return std::bit_cast<std::uint16_t>(pair);
+}
+
+// Counts arrive in the wire's 8-bit form: 0 means 256. Both streamers fold
+// into the one command that reads flash, which is what lets the far one's
+// 24-bit cursor sit in the command loop's own call-saved registers.
+[[maybe_unused, gnu::always_inline]] inline void send_flash_near(std::uint16_t address, std::uint8_t count)
+{
+	do
+		link::tx(avr::flash_load(reinterpret_cast<const std::uint8_t *>(address++)));
+	while (--count);
+}
+
+// The 24-bit cursor as the machine holds it — the RAMPZ byte and a 16-bit Z,
+// carried apart; the reassembled address folds away inside the far load.
+[[maybe_unused, gnu::always_inline]] inline void send_flash_far(std::uint16_t address, std::uint8_t count)
+{
+	std::uint8_t rampz = static_cast<std::uint8_t>(address >> 15);
+	std::uint16_t z = static_cast<std::uint16_t>(address << 1);
+	do {
+		link::tx(avr::flash_load_far<std::uint8_t>((static_cast<std::uint32_t>(rampz) << 16) | z));
+		// Carrying the wrap is smaller than the flat 32-bit cursor GCC
+		// builds without it.
+		if (++z == 0)
+			++rampz;
+	} while (--count);
+}
+
+[[gnu::always_inline]] inline void send_flash(std::uint16_t address, std::uint8_t count)
+{
+	if constexpr (word_flash)
+		send_flash_far(address, count);
+	else
+		send_flash_near(address, count);
+}
+
+// Out of line: three sites send it, and a call is shorter than three
+// load-immediates.
+[[gnu::noinline]] void tx_ack()
+{
+	link::tx(ack);
+}
+
+void send_eeprom(std::uint16_t address, std::uint8_t count)
+{
+	do
+		link::tx(ee::read(address++));
+	while (--count);
+}
+
+// Host-paced: the ack goes out once the write has begun, so the next byte
+// arrives while it completes and nothing is missed without a buffer.
+void store_eeprom(std::uint16_t address, std::uint8_t count)
+{
+	do {
+		ee::write<off>(address++, link::rx());
+		tx_ack();
+	} while (--count);
+}
+
+// One page into the SPM buffer, then erase and program — except the slot
+// this code is running in (`slot_high`, from run()), which is drained and
+// left alone. A broken host therefore cannot brick the running loader, and a
+// copy one slot lower may rewrite the resident one.
+//
+// Nothing discards the buffer first: it is write-once per word (§26.2.1), so
+// filling over a refused page or an application's leavings programs stale
+// words — but a page write auto-erases it (§26.2.1; §19.2 on the tinies), so
+// that write clears the condition and the host's read-back rewrites the page.
+void program_flash(std::uint16_t wire_address, std::uint8_t slot_high)
+{
+	// One induction either way: a byte-addressed wire address walks the page
+	// itself (aligned, so the offset bits wrap to zero), while a word one
+	// becomes a byte cursor once. The slot index is the wire address's high
+	// byte — on byte-addressed chips the byte address's, with the low bit
+	// dropped, since a slot is two of those.
+	spm::flash_address_t address;
+	std::uint8_t page_high;
+	if constexpr (word_flash) {
+		// A page is aligned, so it never crosses 64 KiB: RAMPZ is a per-page
+		// constant and the 16-bit Z's low byte is the whole in-page offset.
+		const std::uint8_t rampz = static_cast<std::uint8_t>(wire_address >> 15);
+		const std::uint16_t z0 = static_cast<std::uint16_t>(wire_address << 1);
+		std::uint16_t z = z0;
+		do {
+			std::uint8_t low = link::rx();
+			std::uint8_t high = link::rx();
+			spm::fill<off>((static_cast<spm::flash_address_t>(rampz) << 16) | z, word_of({low, high}));
+			z += 2;
+		} while (static_cast<std::uint8_t>(z));
+		address = (static_cast<spm::flash_address_t>(rampz) << 16) | z0;
+		page_high = static_cast<std::uint8_t>(wire_address >> 8);
+	} else {
+		address = static_cast<spm::flash_address_t>(wire_address);
+		do {
+			std::uint8_t low = link::rx();
+			std::uint8_t high = link::rx();
+			spm::fill<off>(address, word_of({low, high}));
+			address += 2;
+		} while (static_cast<std::uint8_t>(address) & (page - 1));
+		address -= 2; // back inside the page — erase and write ignore the word bits
+		page_high = static_cast<std::uint8_t>(address >> 8) & 0xfe;
+	}
+	if (page_high != slot_high) {
+		// Only a boot-sectioned mega runs on while its RWW section programs;
+		// everywhere else the CPU halts through erase and write.
+		spm::erase_page<off>(address);
+		if constexpr (boot_section)
+			spm::wait();
+		spm::write_page<off>(address);
+		if constexpr (boot_section)
+			spm::wait();
+	}
+	// Programming leaves the RWW section disabled; reads need it back on. The
+	// same store discards the buffer (§26.2.2), so a boot-sectioned mega never
+	// meets the stale-word case above.
+	if constexpr (boot_section)
+		spm::rww_enable<off>();
+}
+
+// The four fuse and lock bytes in the hardware's own Z order: low, lock,
+// extended, high.
+void send_fuses()
+{
+	std::uint8_t which = 0;
+	do
+		link::tx(spm::read_fuse<off>(static_cast<spm::fuse>(which)));
+	while (++which != 4);
+}
+
+[[noreturn]] void run()
+{
+	// A watchdog reset belongs to the application, whose watchdog stays forced
+	// on until it clears WDRF — no activation window in its way.
+	if (avr::hw::field_impl<wdrf_field()>::test())
+		run_app();
+
+	link::init();
+
+	// The high byte of the slot this copy runs at, which the write guard and
+	// the info block both follow: the return address is a word address, so its
+	// high byte is the 256-word slot index, doubled back into byte terms where
+	// the wire counts bytes. Taken as byteswap's low byte — the builtin already
+	// swaps the two stacked bytes, and the double swap folds away, where `>> 8`
+	// would leave the swap materialized.
+	const std::uint16_t ra_words = reinterpret_cast<std::uint16_t>(__builtin_return_address(0));
+	const std::uint8_t ra_high = static_cast<std::uint8_t>(std::byteswap(ra_words));
+	const std::uint8_t slot_high = word_flash ? ra_high : static_cast<std::uint8_t>(ra_high << 1);
+
+	// 'p' then 'b', each under a fresh window; anything else is line noise.
+	while (rx_deadline() != 'p' || rx_deadline() != 'b') {
+	}
+
+	for (;;) {
+		// No prompt while an EEPROM write runs: it blocks SPM and fuse reads
+		// (§26.2.1), and the prompt is the previous command's completion ack.
+		ee::wait();
+		tx_ack();
+		const std::uint8_t command = link::rx();
+		switch (command) {
+		case 'J': { // jump to a wire word address: hand-over and staging transfer
+			auto target = reinterpret_cast<void (*)()>(rx16());
+			tx_ack();
+			link::drain();
+			jump(target);
+		}
+		case 'b':   // info block, read relative to the running slot
+		case 'R':   // read flash: addr16, n8 (0 = 256)
+		case 'r':   // read EEPROM: addr16, n8
+		case 'w': { // write EEPROM: addr16, n8, then n bytes each acked
+			// One address-and-count path for all four: 'b' is a flash read
+			// whose arguments the loader already knows, so it joins the
+			// wire-argument three rather than streaming from a call site of its
+			// own. That leaves one flash streamer in the image, and lets its
+			// cursor live in this never-returning loop's own call-saved
+			// registers instead of being saved and restored around a call.
+			std::uint16_t address;
+			std::uint8_t count;
+			if (command == 'b') {
+				// The block sits in the image's first 256 bytes (check_pi.py
+				// asserts it) and slots are 512-aligned, so the low byte of its
+				// link address is its offset in any slot — halved where wire
+				// units are words. The high byte is runtime data, so no
+				// absolute address is ever materialized.
+				const auto link_byte =
+				    static_cast<std::uint8_t>(reinterpret_cast<std::uint16_t>(info_data.storage.data()));
+				const std::uint8_t low = word_flash ? static_cast<std::uint8_t>(link_byte >> 1) : link_byte;
+				address = static_cast<std::uint16_t>(low | (slot_high << 8));
+				count = static_cast<std::uint8_t>(info_data.size());
+			} else {
+				address = rx16();
+				count = link::rx();
+			}
+			if (command == 'r')
+				send_eeprom(address, count);
+			else if (command == 'w')
+				store_eeprom(address, count);
+			else
+				send_flash(address, count);
+			break;
+		}
+		case 'W': // program one flash page: addr16, page bytes
+			program_flash(rx16(), slot_high);
+			break;
+		case 'F': // fuse and lock bytes
+			send_fuses();
+			break;
+		default: // unknown bytes are ignored; the loop re-acks
+			break;
+		}
+	}
+}
+
+} // namespace
+} // namespace pureboot
+
+template struct avr::startup::entry<pureboot::run>;

test/check_pi.py

@@ -0,0 +1,48 @@
+#!/usr/bin/env python3
+"""Position-independence lint: the two link-time facts that let the identical
+image run from any slot, asserted from the built ELF.
+
+  1. No absolute jmp/call — -mrelax normally guarantees it, but a branch that
+     grows out of relaxation range would break it silently.
+  2. The info block within the image's first 256 bytes: 'b' rebuilds its
+     address as (running slot high byte : link address low byte).
+
+Usage: check_pi.py <objdump> <nm> <elf> <text_start_hex>
+"""
+
+import re
+import subprocess
+import sys
+
+
+def main():
+    objdump, nm, elf, text_start = sys.argv[1:]
+    text_start = int(text_start, 0)
+
+    listing = subprocess.run([objdump, "-d", elf], capture_output=True, text=True, check=True).stdout
+    absolute = [
+        line
+        for line in listing.splitlines()
+        if re.search(r"\t(jmp|call)\t", line)
+    ]
+    if absolute:
+        print("FAIL: absolute control flow in the image:")
+        print("\n".join(absolute))
+        sys.exit(1)
+
+    symbols = subprocess.run([nm, "-C", elf], capture_output=True, text=True, check=True).stdout
+    info = [line for line in symbols.splitlines() if "flash_table" in line and "::storage" in line]
+    if len(info) != 1:
+        print(f"FAIL: expected one info-block storage symbol, found {len(info)}")
+        sys.exit(1)
+    address = int(info[0].split()[0], 16)
+    offset = address - text_start
+    if not 0 <= offset < 256:
+        print(f"FAIL: info block at image offset {offset:#x}, must sit in the first 256 bytes")
+        sys.exit(1)
+
+    print(f"PI lint: control flow PC-relative, info block at offset {offset:#x}")
+
+
+if __name__ == "__main__":
+    main()

test/check_size.cmake

@@ -4,9 +4,6 @@ if(NOT _res EQUAL 0)
 endif()
 # avr-size line 2 is "<text> <data> <bss> <dec> <hex> <file>".
 string(REGEX MATCH "\n[ \t]*([0-9]+)" _m "${_out}")
-if(NOT _m)
-	message(FATAL_ERROR "could not read a .text size out of ${SIZE_TOOL}'s output for ${ELF}:\n${_out}")
-endif()
 set(_text ${CMAKE_MATCH_1})
 if(_text GREATER LIMIT)
 	message(FATAL_ERROR ".text is ${_text} bytes, over the ${LIMIT}-byte boot section")

test/device.c

@@ -7,122 +7,103 @@
 // SPM genuinely writes avr->flash on the mega cores, so on exit (or SIGTERM)
 // we dump the flash image to a file for a ground-truth cross-check against
 // what the client read back through the bootloader.
-#include <array>
+#include <signal.h>
-#include <csignal>
+#include <stdint.h>
-#include <cstdint>
+#include <stdio.h>
-#include <cstdio>
+#include <stdlib.h>
-#include <cstdlib>
+#include <string.h>
-#include <cstring>
-#include <print>
-
 #include <unistd.h>
 
-// The parts headers (uart_pty.h) carry no C++ linkage guards of their own,
-// unlike simavr's core headers - the block covers both harmlessly.
-extern "C" {
 #include "avr_uart.h"
 #include "sim_avr.h"
 #include "sim_elf.h"
 #include "uart_pty.h"
-}
 
-namespace {
+static avr_t *avr;
+static uart_pty_t uart_pty;
+static const char *dump_path;
 
-avr_t *avr;
+static void finish(int sig)
-uart_pty_t uart_pty;
-const char *dump_path;
-
-[[noreturn]] void finish(int)
 {
+	(void)sig;
 	if (dump_path) {
-		std::FILE *f = std::fopen(dump_path, "wb");
+		FILE *f = fopen(dump_path, "wb");
 		if (f) {
-			std::fwrite(avr->flash, 1, avr->flashend + 1, f);
+			fwrite(avr->flash, 1, avr->flashend + 1, f);
-			std::fclose(f);
+			fclose(f);
 		}
 	}
 	uart_pty_stop(&uart_pty);
 	_exit(0);
 }
 
-} // namespace
-
 int main(int argc, char *argv[])
 {
 	if (argc < 3) {
-		std::println(stderr, "usage: {} <tsb.elf> <boot_base_hex> [flash_dump.bin]", argv[0]);
+		fprintf(stderr, "usage: %s <tsb.elf> <boot_base_hex> [flash_dump.bin]\n", argv[0]);
 		return 2;
 	}
-	auto boot_base = static_cast<std::uint32_t>(std::strtoul(argv[2], nullptr, 0));
+	uint32_t boot_base = (uint32_t)strtoul(argv[2], NULL, 0);
-	dump_path = argc >= 4 ? argv[3] : nullptr;
+	dump_path = argc >= 4 ? argv[3] : NULL;
 
 	avr = avr_make_mcu_by_name("atmega328p");
 	if (!avr) {
-		std::println(stderr, "device: no ATmega328P core");
+		fprintf(stderr, "device: no ATmega328P core\n");
 		return 1;
 	}
 	avr_init(avr);
 	avr->frequency = 16000000;
 	// Real flash powers up erased (0xff); the app region must look erased
 	// before the bootloader programs it.
-	std::memset(avr->flash, 0xff, avr->flashend + 1);
+	memset(avr->flash, 0xff, avr->flashend + 1);
 
 	// simavr's ELF loader flattens the flash base to 0 (it expects an app at
 	// 0x0), but it hands back the boot code in fw.flash; place it at the boot
 	// section base ourselves and enter there (BOOTRST is not modelled).
-	elf_firmware_t fw{};
+	elf_firmware_t fw = {0};
 	if (elf_read_firmware(argv[1], &fw) != 0) {
-		std::println(stderr, "device: cannot read {}", argv[1]);
+		fprintf(stderr, "device: cannot read %s\n", argv[1]);
 		return 1;
 	}
-	// An image that runs past flash end cannot execute on hardware, and a
+	memcpy(avr->flash + boot_base, fw.flash, fw.flashsize);
-	// naive copy of it would smash the heap beyond avr->flash - after which
-	// the simulation misbehaves in ways that point everywhere but here.
-	// Refuse it loudly instead.
-	if (boot_base + fw.flashsize > avr->flashend + 1) {
-		std::println(stderr, "device: {} B at {:#x} runs past flash end {:#x} - image does not fit its slot",
-		             fw.flashsize, boot_base, avr->flashend);
-		return 1;
-	}
-	std::memcpy(avr->flash + boot_base, fw.flash, fw.flashsize);
 	avr->pc = boot_base;
 	avr->codeend = avr->flashend;
 
 	// Optional: seed the config page (one page below the boot section) with a
 	// hex byte string, so the password gate and emergency erase can be tested.
 	// Layout: [appjump lo][appjump hi][timeout][password...][0xff].
-	const char *cfg = std::getenv("TSB_CONFIG");
+	const char *cfg = getenv("TSB_CONFIG");
 	if (cfg) {
-		std::uint32_t app_end = boot_base - 128; // config page sits directly below the boot code
+		uint32_t app_end = boot_base - 128; // config page sits directly below the boot code
 		for (int i = 0; cfg[i] && cfg[i + 1]; i += 2) {
-			const std::array pair{cfg[i], cfg[i + 1], '\0'};
+			char b[3] = {cfg[i], cfg[i + 1], 0};
-			avr->flash[app_end + i / 2] = static_cast<std::uint8_t>(std::strtoul(pair.data(), nullptr, 16));
+			avr->flash[app_end + i / 2] = (uint8_t)strtoul(b, NULL, 16);
 		}
 	}
 
 	// POLL_SLEEP makes simavr usleep(1) on every status-register read while the
-	// UART is idle - a host-CPU-saving hack that models no hardware and paces a
+	// UART is idle — a host-CPU-saving hack that models no hardware and paces a
 	// tight-polling loader (one that releases TX between bytes, as one-wire does)
 	// in real time, distorting protocol timing. Clear it so the loader runs at
 	// true cycle speed.
-	std::uint32_t uflags = 0;
+	uint32_t uflags = 0;
 	avr_ioctl(avr, AVR_IOCTL_UART_GET_FLAGS('0'), &uflags);
 	uflags &= ~AVR_UART_FLAG_POLL_SLEEP;
 	avr_ioctl(avr, AVR_IOCTL_UART_SET_FLAGS('0'), &uflags);
 
 	uart_pty_init(avr, &uart_pty);
 	uart_pty_connect(&uart_pty, '0');
-	std::println("TSB_PTY {}", uart_pty.pty.slavename);
+	printf("TSB_PTY %s\n", uart_pty.pty.slavename);
-	std::fflush(stdout);
+	fflush(stdout);
 
-	std::signal(SIGTERM, finish);
+	signal(SIGTERM, finish);
-	std::signal(SIGINT, finish);
+	signal(SIGINT, finish);
 
 	for (;;) {
 		int state = avr_run(avr);
-		if (state == cpu_Done || state == cpu_Crashed) {
+		if (state == cpu_Done || state == cpu_Crashed)
 			break;
 	}
-	}
 	finish(0);
+	return 0;
 }

test/pbapp.cpp

@@ -0,0 +1,116 @@
+// Test-fixture application for the pureboot protocol tests: prints "APP" on
+// the chip's serial link (the same link the loader uses) — the proof that
+// the loader's hand-over, and on the tinies the host's reset-vector
+// surgery, actually launched it. Linked normally (crt, vectors at 0); on
+// the tinies its reset vector is the rjmp the host re-homes.
+//
+// On the hardware-USART link it then listens, and an 'L' makes it jump into
+// the resident loader — the application-owned loader entry a
+// BOOTRST-unprogrammed mega relies on (reset always boots the application
+// there), exercised by the self-update tests. The software link idles:
+// reset reaches those loaders through the patched vector (or the runner
+// models BOOTRST), so the application owes them nothing.
+//
+// The fixture speaks the deployment its loader was built for: the same
+// PUREBOOT_* defines configure it, and without them it assumes the stock
+// deployment (the crystal/RC clock table below, the chip's natural link).
+#include <libavr/libavr.hpp>
+
+using namespace avr::literals;
+
+namespace {
+
+consteval avr::hertz_t clock()
+{
+#if defined(PUREBOOT_CLOCK_HZ)
+	return avr::hertz_t{PUREBOOT_CLOCK_HZ};
+#else
+	auto name = std::string_view{avr::hw::db.name};
+	if (name.starts_with("ATtiny13"))
+		return 9.6_MHz;
+	if (name.starts_with("ATtiny"))
+		return 8_MHz;
+	return 16_MHz;
+#endif
+}
+
+#if !defined(PUREBOOT_TX)
+#define PUREBOOT_TX pb1
+#endif
+#if !defined(PUREBOOT_USART)
+#define PUREBOOT_USART 0
+#endif
+
+consteval bool use_hardware()
+{
+#if defined(PUREBOOT_SOFT_SERIAL)
+	return false;
+#else
+	return avr::hw::db.has_instance("USART0") || avr::hw::db.has_instance("USART");
+#endif
+}
+
+using dev = avr::device<{.clock = clock()}>;
+
+template <avr::hertz_t C, bool Hardware = use_hardware()>
+struct link {
+#if defined(PUREBOOT_BAUD)
+	static constexpr avr::baud_t baud{PUREBOOT_BAUD};
+#else
+	static constexpr avr::baud_t baud{115200};
+#endif
+	using tx_t = avr::uart::usart<'0' + PUREBOOT_USART, C, {.baud = baud, .max_baud_error = 2.5_pct}>;
+	static void tx(char c)
+	{
+		tx_t::write(static_cast<std::uint8_t>(c));
+	}
+	[[noreturn]] static void idle()
+	{
+		// 'L' hands back to the loader in the top slot — 512 bytes on every
+		// chip. The jump takes a word address, which is what makes the
+		// >64 KiB chips' entry reachable through a 16-bit pointer at all.
+		constexpr std::uint32_t slot = 512;
+		for (;;) {
+			auto command = tx_t::read_blocking();
+			if (command == 'L')
+				reinterpret_cast<void (*)()>(static_cast<std::uint16_t>((avr::hw::db.mem.flash_size - slot) / 2))();
+			// 'D' leaves every word of the SPM page buffer dirty, so that a
+			// following 'L' enters the loader with the buffer it never clears.
+			if (command == 'D') {
+				for (std::uint16_t at = 0; at < avr::spm::page_bytes; at += 2)
+					avr::spm::fill(at, 0xdead);
+				tx('D');
+			}
+		}
+	}
+};
+
+template <avr::hertz_t C>
+struct link<C, false> {
+#if defined(PUREBOOT_BAUD)
+	static constexpr avr::baud_t baud{PUREBOOT_BAUD};
+#else
+	static constexpr avr::baud_t baud{57600};
+#endif
+	using tx_t = avr::uart::software_tx<C, avr::PUREBOOT_TX, baud>;
+	static void tx(char c)
+	{
+		tx_t::write(static_cast<std::uint8_t>(c));
+	}
+	[[noreturn]] static void idle()
+	{
+		while (true) {
+		}
+	}
+};
+
+} // namespace
+
+int main()
+{
+	avr::init<typename link<dev::clock>::tx_t>();
+	link<dev::clock>::tx('A');
+	link<dev::clock>::tx('P');
+	link<dev::clock>::tx('P');
+	link<dev::clock>::idle();
+}

test/pbdirty.py

@@ -0,0 +1,88 @@
+#!/usr/bin/env python3
+"""Dirty-page-buffer acceptance test: with no discard in the loader, a page
+filled over words an earlier writer left takes those instead. The whole
+contract is asserted — a bare verify sees the corruption, the repairing
+verify fixes it in one rewrite, and it stays fixed.
+
+The state is reached the one way the loader cannot prevent: an application
+dirties the buffer and jumps in with no reset between. Boot-sectioned megas
+forbid that outright (SPM runs only from the boot section, Atmel-8271 §26.2),
+but simavr dispatches SPM from anywhere, which is what makes it constructible.
+
+Usage: pbdirty.py <device_bin> <pureboot_elf> <mcu> <hz> <base_hex> <page>
+                  <baud> <app_bin> <tool_py> <workdir>
+"""
+
+import os
+import sys
+
+
+def fail(message):
+    print(f"FAIL: {message}")
+    sys.exit(1)
+
+
+def main():
+    device_bin, elf, mcu, hz, base_hex, page, baud, app_bin, tool, workdir = sys.argv[1:]
+    page, baud = int(page), int(baud)
+    sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
+    sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
+    import pbsim
+    import pureboot as pb
+
+    os.makedirs(workdir, exist_ok=True)
+    dump = os.path.join(workdir, "dump.bin")
+
+    # Reset boots the application on a BOOTRST-unprogrammed mega; its 'L' is
+    # the loader entry this test needs, reached without a reset.
+    device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump, reset_hex="0")
+    try:
+        port = pb.Port(device.pty, baud)
+        loader = pb.Loader(port)
+        loader.connect(25)
+
+        # Install the application and hand over to it.
+        pb.op_flash(loader, app_bin, erase=False, verify=True)
+        loader.run_application()
+        if port.read_exact(3, 5.0) != b"APP":
+            fail("the application did not start")
+
+        port.write(b"D")
+        if port.read_exact(1, 5.0) != b"D":
+            fail("the application did not acknowledge dirtying the page buffer")
+        port.write(b"L")
+        loader = pb.Loader(port)
+        loader.connect(25)
+
+        # Program by hand, so the corruption is observable before anything
+        # repairs it.
+        pages = pb.plan_flash(open(app_bin, "rb").read(), loader.info)
+        for address in sorted(pages):
+            loader.write_page(address, pages[address])
+        try:
+            pb.verify_pages(loader, pages)
+        except pb.Error as error:
+            if "verify failed" not in str(error):
+                fail(f"the read-back failed, but not at verify: {error}")
+        else:
+            # Either the fixture no longer dirties the buffer, or the loader
+            # clears it again — in which case this test's premise is gone.
+            fail("programming over a dirty page buffer came back clean")
+
+        # What the programming path uses: one rewrite settles it, and it stays
+        # settled.
+        pb.verify_pages(loader, pages, repair=True)
+        pb.verify_pages(loader, pages)
+
+        # Ground truth beyond the loader's own read-back.
+        loader.run_application()
+        if port.read_exact(3, 5.0) != b"APP":
+            fail("the application did not start after the recovered write")
+        port.close()
+    finally:
+        device.stop()
+    print("pbdirty: a dirty page buffer is caught by verify and cleared by the retry")
+
+
+if __name__ == "__main__":
+    main()

test/pbrehome.py

@@ -0,0 +1,96 @@
+#!/usr/bin/env python3
+"""Re-homing acceptance test: an image programmed somewhere other than its
+canonical slot must still be a working loader, and the ordinary
+--update-loader flow must put a build into the top slot from there.
+
+Two positions. Address 0, a raw .bin handed to a programmer: the staging
+install and the word-0 redirect run from copies outside page 0's slot, so the
+running-slot guard never blocks them. And the staging slot itself, where a
+loader already sitting there IS the staging copy — recognized by its embedded
+block and left in place, then streaming the new resident like any staged copy.
+
+Usage: pbrehome.py <device_bin> <pureboot_elf> <update_bin> <mcu> <hz>
+                   <base_hex> <page> <baud> <app_bin> <tool_py> <workdir>
+"""
+
+import os
+import sys
+
+
+def fail(message):
+    print(f"FAIL: {message}")
+    sys.exit(1)
+
+
+def rehome_from(pbsim, pb, device_bin, elf, place_hex, guard_probe, update_bin, base, page, baud, app_bin, workdir,
+                mcu, hz):
+    """Place the loader at `place_hex`, heal through --update-loader, flash
+    the application, expect the banner."""
+    dump = os.path.join(workdir, f"dump-{place_hex}.bin")
+    state = os.path.join(workdir, f"rehome-{place_hex}.pbstate")
+    if os.path.exists(state):
+        os.unlink(state)
+    device = pbsim.Device(device_bin, elf, mcu, hz, place_hex, page, baud, dump, reset_hex="0")
+    try:
+        port = pb.Port(device.pty, baud)
+        loader = pb.Loader(port)
+        info = loader.connect(25)
+        if info.base != base:
+            fail(f"the misplaced copy reports base {info.base:#06x} — the info block must stay canonical")
+
+        # The accidental slot still guards itself; re-homing rides on the
+        # canonical slots being writable from it.
+        probe = int(guard_probe, 0)
+        before = loader.read_flash(probe, info.page)
+        loader.write_page(probe, bytes(info.page))
+        if loader.read_flash(probe, info.page) != before:
+            fail("the misplaced copy's guard let its own slot change")
+
+        # The ordinary update flow puts the build into the top slot.
+        pb.op_update_loader(loader, 25, update_bin, state, None)
+        update = open(update_bin, "rb").read()
+        if loader.read_flash(base, len(update)) != update:
+            fail("the canonical slot does not hold the update image")
+
+        # An application flashed through the healed resident overwrites the
+        # stale copy (surgery included) and launches.
+        pages = pb.plan_flash(open(app_bin, "rb").read(), loader.info)
+        for address in pb.covered(pages, loader.info, skip_blank=False):
+            loader.write_page(address, pages[address])
+        pb.verify_pages(loader, pages)
+        loader.run_application()
+        if port.read_exact(3, 5.0) != b"APP":
+            fail(f"application does not banner after the re-home from {place_hex}")
+        port.close()
+    finally:
+        device.stop()
+
+
+def main():
+    (device_bin, elf, update_bin, mcu, hz, base_hex, page, baud, app_bin, tool, workdir) = sys.argv[1:]
+    base, page, baud = int(base_hex, 0), int(page), int(baud)
+    sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
+    sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
+    import pbsim
+    import pureboot as pb
+
+    os.makedirs(workdir, exist_ok=True)
+
+    # Address 0: the raw-.bin-to-a-programmer accident. The guard probe is
+    # the copy's own page 0.
+    rehome_from(pbsim, pb, device_bin, elf, "0x0", "0x0", update_bin, base, page, baud, app_bin, workdir, mcu, hz)
+    print("re-home from address 0: converged")
+
+    # The staging slot: erased flash with the loader sitting exactly where
+    # a staging copy would — the tool must leave it in place and let it
+    # stream the (different) update build into the resident slot.
+    stage = base - pb.SLOT
+    rehome_from(pbsim, pb, device_bin, elf, hex(stage), hex(stage), update_bin, base, page, baud, app_bin, workdir,
+                mcu, hz)
+    print("re-home from the staging slot: converged")
+
+    print("pbrehome: a misplaced loader re-homes through the ordinary update flow")
+
+
+if __name__ == "__main__":
+    main()

test/pbreloc.py

@@ -0,0 +1,96 @@
+#!/usr/bin/env python3
+"""Position-independence acceptance test: the identical binary, flashed one
+slot below the resident, must serve the complete command set from there. The
+info block must come back byte-identical, the write guard must refuse the
+staged copy's own slot and permit the resident's, and the staged copy must be
+able to rewrite the resident verbatim.
+
+Usage: pbreloc.py <device_bin> <pureboot_elf> <mcu> <hz> <base_hex> <page>
+                  <baud> <tool_py> <workdir>
+"""
+
+import os
+import subprocess
+import sys
+
+
+def fail(message):
+    print(f"FAIL: {message}")
+    sys.exit(1)
+
+
+def main():
+    device_bin, elf, mcu, hz, base_hex, page, baud, tool, workdir = sys.argv[1:]
+    base, page, baud = int(base_hex, 0), int(page), int(baud)
+    stage = None  # derived from the device's own info (slot-sized) below
+    sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
+    sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
+    import pbsim
+    import pureboot as pb
+
+    os.makedirs(workdir, exist_ok=True)
+    objcopy = os.environ.get("PB_OBJCOPY", "avr-objcopy")
+    image_path = os.path.join(workdir, "pureboot.bin")
+    subprocess.run([objcopy, "-O", "binary", elf, image_path], check=True)
+    image = open(image_path, "rb").read()
+
+    device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, os.path.join(workdir, "dump.bin"))
+    try:
+        port = pb.Port(device.pty, baud)
+        loader = pb.Loader(port)
+        info = loader.connect(25)
+        if info.base != base:
+            fail(f"info reports base {info.base:#06x}")
+        resident_info = info.raw
+
+        # Install the staging copy exactly as the update flow would.
+        stage = info.stage
+        staged = pb.staging_content(image, info)
+        pb.write_differing(loader, stage, staged)
+
+        # Enter it; from here on, every command runs in the relocated copy.
+        staged_info = loader.enter_copy(stage, 25)
+        if staged_info.raw != resident_info:
+            fail(f"staged info {staged_info.raw.hex()} != resident info {resident_info.hex()}")
+
+        # 'R' from the staged copy already proved itself in the install
+        # verify; 'F' must answer 4 bytes (values are unmodeled in simavr).
+        if len(loader.read_fuses()) != 4:
+            fail("fuse read from the staged copy")
+
+        # EEPROM round-trip through the staged copy.
+        pattern = bytes(range(0x50, 0x60))
+        loader.write_eeprom(0, pattern)
+        if loader.read_eeprom(0, len(pattern)) != pattern:
+            fail("EEPROM round-trip through the staged copy")
+
+        # The guard, both ways: its own slot refused (drained, unchanged), the
+        # resident slot writable. The refusal leaves its drained words in the
+        # SPM buffer, so the write that follows may take them — and clears
+        # them by writing, so the retry must not.
+        before = loader.read_flash(stage, page)
+        loader.write_page(stage, bytes(page))
+        if loader.read_flash(stage, page) != before:
+            fail("the staged copy's guard let its own slot change")
+        marker = bytes((i * 3) & 0xFF for i in range(page))
+        loader.write_page(base, marker)
+        if loader.read_flash(base, page) != marker:
+            loader.write_page(base, marker)
+            if loader.read_flash(base, page) != marker:
+                fail("the staged copy could not write the resident slot, even on retry")
+
+        # Restore the resident image through the staged copy, then 'J' back
+        # into it and prove it lives.
+        resident = image + b"\xff" * (pb.SLOT - len(image))
+        pb.write_differing(loader, base, resident)
+        back_info = loader.enter_copy(base, 25)
+        if back_info.raw != resident_info:
+            fail("the restored resident does not serve its info block")
+        port.close()
+    finally:
+        device.stop()
+    print("pbreloc: the relocated copy serves the full command set")
+
+
+if __name__ == "__main__":
+    main()

test/pbsim.py

@@ -0,0 +1,68 @@
+"""Shared simavr harness for the pureboot tests: spawn the device runner,
+hand out its pty, restart it from a flash dump (the power-fail path), and
+keep its chatter out of undrained pipes."""
+
+import os
+import signal
+import subprocess
+
+
+class Device:
+    def __init__(self, binary, elf, mcu, hz, base_hex, page, baud, dump, reset_hex=None, resume=None, link=None):
+        cmd = [binary]
+        if link:
+            cmd += ["-l", link]
+        cmd += [elf, mcu, hz, base_hex, str(page), str(baud), dump]
+        if reset_hex is not None or resume is not None:
+            # Chips without a hardware boot section — the tinies and the
+            # m48s — reset to address 0 like silicon; the boot-sectioned
+            # megas re-vector to the loader base (BOOTRST).
+            patch = not mcu.startswith("atmega") or mcu.startswith("atmega48")
+            cmd.append(reset_hex if reset_hex is not None else ("0" if patch else base_hex))
+        if resume is not None:
+            cmd.append(resume)
+        self.log = open(dump + ".log", "a")
+        self.proc = subprocess.Popen(cmd, stdout=subprocess.PIPE, stderr=self.log, text=True)
+        self.dump = dump
+        self.pty = None
+        for _ in range(50):
+            line = self.proc.stdout.readline()
+            if not line:
+                break
+            if line.startswith("PB_PTY"):
+                self.pty = line.split()[1]
+                break
+        if not self.pty:
+            self.stop()
+            raise RuntimeError("device did not report a pty")
+
+    def reset(self):
+        """The external reset line: SIGUSR1 re-enters at the reset vector."""
+        self.proc.send_signal(signal.SIGUSR1)
+
+    def power_fail(self):
+        """SIGTERM: the runner dumps its flash and exits — the image a
+        restart resumes from."""
+        self.stop()
+        return self.dump
+
+    def stop(self):
+        self.proc.terminate()
+        try:
+            self.proc.wait(timeout=5)
+        except subprocess.TimeoutExpired:
+            self.proc.kill()
+        self.log.close()
+
+
+def run_tool(tool, pty, baud, *args, timeout=180):
+    result = subprocess.run(
+        [os.environ.get("PYTHON", "python3"), tool, "--port", pty, "--baud", str(baud), "--wait", "25", *args],
+        capture_output=True,
+        text=True,
+        timeout=timeout,
+    )
+    print(result.stdout, end="")
+    if result.returncode != 0:
+        raise RuntimeError(f"tool exited {result.returncode}: {result.stderr.strip()}")
+    return result.stdout

test/pbtest.py

@@ -0,0 +1,147 @@
+#!/usr/bin/env python3
+"""End-to-end protocol test: drive the simavr device with the real host tool
+over its pty through flash, EEPROM, fuse and hand-over scenarios, and
+cross-check the tool's view against the simulator's ground-truth dumps.
+
+Usage: pbtest.py <device_bin> <pureboot_elf> <mcu> <hz> <base_hex> <page>
+                 <baud> <eeprom_size> <app_bin> <tool_py> <workdir> [link]
+
+The optional link is the runner's -l spec (usart1, sw:B5,B1, ...), for a
+loader built off the chip's natural serial default.
+"""
+
+import os
+import sys
+
+
+def fail(message):
+    print(f"FAIL: {message}")
+    sys.exit(1)
+
+
+def rjmp_decode(word, at, flash_words):
+    """Where an rjmp word at word-address `at` lands — deliberately written
+    against the instruction-set definition (12-bit signed offset), not with
+    the host tool's encoder, so an encoding bug cannot verify itself."""
+    if word & 0xF000 != 0xC000:
+        fail(f"word at {at * 2:#06x} is {word:#06x}, not an rjmp")
+    offset = word & 0x0FFF
+    if offset >= 0x800:
+        offset -= 0x1000
+    return (at + 1 + offset) % flash_words
+
+
+def main():
+    args = sys.argv[1:]
+    link = args.pop() if len(args) == 12 else None
+    (device_bin, elf, mcu, hz, base_hex, page, baud, eeprom_size, app_bin, tool, workdir) = args
+    base, page, baud, eeprom_size = int(base_hex, 0), int(page), int(baud), int(eeprom_size)
+    sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
+    sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
+    import pbsim
+    import pureboot as pb
+
+    os.makedirs(workdir, exist_ok=True)
+    ee_image = bytes(range(0xA0, 0xB0))
+    ee_path = os.path.join(workdir, "ee.bin")
+    open(ee_path, "wb").write(ee_image)
+    dump = os.path.join(workdir, "flash_dump.bin")
+    read_flash = os.path.join(workdir, "readback_flash.bin")
+    read_eeprom = os.path.join(workdir, "readback_eeprom.bin")
+
+    # The geometry the host will discover, for computing the expected image:
+    # the boot-sectioned megas need no vector surgery (the tinies and the
+    # boot-section-less m48s do), the large chips speak word addresses, and
+    # the page byte is the wire's 0-means-256.
+    mega = mcu.startswith("atmega")
+    patch = not mega or mcu.startswith("atmega48")
+    word_flash = base + pb.SLOT > 0x10000
+    wire_base = base // 2 if word_flash else base
+    flags = (1 if patch else 0) | (2 if word_flash else 0)
+    info = pb.Info(
+        bytes([ord("P"), ord("B"), pb.NEWEST_LOADER, 0, 0, 0, page & 0xFF])
+        + bytes([wire_base & 0xFF, wire_base >> 8, eeprom_size & 0xFF, eeprom_size >> 8])
+        + bytes([flags])
+    )
+
+    device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump, link=link)
+    try:
+        # Session 1: knock from reset, identify, program everything, stay.
+        out = pbsim.run_tool(tool, device.pty, baud, "--info", "--fuses", "--flash", app_bin,
+                             "--eeprom", ee_path, "--stay")
+        for needed in ("version", "signature", "fuses", "verify:", "stays"):
+            if needed not in out:
+                fail(f"session 1 output lacks {needed!r}")
+
+        # Session 2: reconnect into the live session, verify, dump, hand over
+        # is deferred — the pty must be reopened for the APP banner first.
+        out = pbsim.run_tool(tool, device.pty, baud, "--verify-flash", app_bin, "--verify-eeprom", ee_path,
+                             "--read-flash", read_flash, "--read-eeprom", read_eeprom, "--stay")
+        if out.count("verify:") != 2:
+            fail("session 2 did not verify both memories")
+
+        eeprom_back = open(read_eeprom, "rb").read()
+        if eeprom_back[: len(ee_image)] != ee_image:
+            fail("EEPROM read-back mismatch")
+
+        # The expected post-surgery flash, straight from the tool's planner.
+        pages = pb.plan_flash(open(app_bin, "rb").read(), info)
+        flash_back = open(read_flash, "rb").read()
+        for address, data in pages.items():
+            if flash_back[address : address + page] != data:
+                fail(f"flash read-back mismatch in page {address:#06x}")
+
+        # An external reset re-enters through the patched word 0 (tinies; the
+        # runner resets them to address 0 like silicon) or BOOTRST (mega).
+        # The loader must answer a fresh knock, and the 'J' hand-over must
+        # land in the application, which banners on the same link.
+        device.reset()
+        port = pb.Port(device.pty, baud)
+        try:
+            loader = pb.Loader(port)
+            live = loader.connect(15)
+            # The loader built from this tree and the tool beside it must
+            # agree on where the version numbering stands: a bump the tool
+            # was never told about is a loader it would refuse to speak to.
+            if live.version != pb.NEWEST_LOADER:
+                fail(f"loader reports pureboot {live.version}, the tool's newest is {pb.NEWEST_LOADER}")
+            loader.run_application()
+            banner = port.read_exact(3, 5.0)
+            if banner != b"APP":
+                fail(f"application banner was {banner!r}")
+        finally:
+            port.close()
+    finally:
+        device.stop()
+
+    # Ground truth: the simulator's own memories, against the host's view.
+    flash_true = open(dump, "rb").read()
+    if flash_true[:base] != flash_back:
+        fail("host flash read-back differs from the simulator's flash")
+    if flash_true[base] == 0xFF and flash_true[base + 1] == 0xFF:
+        fail("loader region looks erased in the ground-truth dump")
+
+    # The surgery, decoded independently: the patched vector must land on the
+    # loader, the trampoline on the application's own entry (patched-vector
+    # chips only — a boot-sectioned mega's word 0 stays the application's).
+    if patch:
+        flash_words = (base + pb.SLOT) // 2
+        app = open(app_bin, "rb").read()
+        word0 = flash_true[0] | (flash_true[1] << 8)
+        if rjmp_decode(word0, 0, flash_words) != base // 2:
+            fail("patched reset vector does not land on the loader base")
+        trampoline = flash_true[base - 2] | (flash_true[base - 1] << 8)
+        original = app[0] | (app[1] << 8)
+        if rjmp_decode(trampoline, (base - 2) // 2, flash_words) != rjmp_decode(original, 0, flash_words):
+            fail("trampoline does not land on the application's own entry")
+    ee_true_path = dump + ".eeprom"
+    if os.path.exists(ee_true_path):
+        ee_true = open(ee_true_path, "rb").read()
+        if ee_true[: len(ee_image)] != ee_image:
+            fail("ground-truth EEPROM does not match what was programmed")
+
+    print("pbtest: all scenarios pass")
+
+
+if __name__ == "__main__":
+    main()

test/pbupdate.py

@@ -0,0 +1,222 @@
+#!/usr/bin/env python3
+"""Self-update end-to-end: an application is flashed, the loader replaces
+itself with a re-timed build, and every power-fail phase is rehearsed by
+killing the device mid-write, restarting it from its flash dump, and letting
+a re-run complete the update.
+
+The boot-sectioned megas run the BOOTRST-unprogrammed profile — reset boots
+the application, whose 'L' is the application-owned loader entry — with
+--assume-fuses standing in for the fuse read simavr cannot model.
+
+Usage: pbupdate.py <device_bin> <pureboot_elf> <update_elf> <mcu> <hz>
+                   <base_hex> <page> <baud> <app_bin> <tool_py> <workdir>
+"""
+
+import os
+import subprocess
+import sys
+
+
+def fail(message):
+    print(f"FAIL: {message}")
+    sys.exit(1)
+
+
+def rjmp_decode(word, at, flash_words):
+    """Written against the instruction-set definition, not with the tool's
+    encoder, so an encoding bug cannot verify itself."""
+    if word & 0xF000 != 0xC000:
+        fail(f"word at {at * 2:#06x} is {word:#06x}, not an rjmp")
+    offset = word & 0x0FFF
+    if offset >= 0x800:
+        offset -= 0x1000
+    return (at + 1 + offset) % flash_words
+
+
+class PowerFail(Exception):
+    pass
+
+
+def assumed_fuses(pb, image):
+    """Synthetic 'F' bytes for --assume-fuses: the smallest boot section
+    covering both the resident and the staging slot (two slots — what a
+    self-update needs), BOOTRST unprogrammed — the per-chip BOOTSZ ladder
+    and fuse byte come from the tool's own table, keyed by the update
+    image's embedded signature."""
+    info = pb.image_info(image)
+    which, ladder = pb.BOOT_FUSE[bytes(info.signature[1:3])]
+    bits = min((b for b in ladder if ladder[b] * 2 >= 2 * pb.SLOT), key=lambda b: ladder[b])
+    fuses = bytearray((0xFF, 0xFF, 0xFF, 0xFF))
+    fuses[which] = 0xF8 | (bits << 1) | 1
+    return bytes(fuses)
+
+
+def make_fault_loader(pb, base, slot, kill_region, kill_hits, device):
+    """A Loader whose write_page kills the device (or, with device=None,
+    just the host) at the Nth write into a region; the sequence
+    stage->resident->stage distinguishes the install from the restore."""
+
+    class FaultLoader(pb.Loader):
+        def __init__(self, port):
+            super().__init__(port)
+            self.seen_resident = False
+            self.hits = 0
+
+        def write_page(self, address, data):
+            if address >= base:
+                phase = "resident"
+                self.seen_resident = True
+            elif address >= base - slot:
+                phase = "stage_restore" if self.seen_resident else "stage"
+            else:
+                phase = "app"
+            if phase == kill_region:
+                self.hits += 1
+                if self.hits == kill_hits:
+                    if device is not None:
+                        device.power_fail()
+                    raise PowerFail(f"{kill_region} write {kill_hits}")
+            super().write_page(address, data)
+
+    return FaultLoader
+
+
+def main():
+    (device_bin, elf, update_elf, mcu, hz, base_hex, page, baud, app_bin, tool, workdir) = sys.argv[1:]
+    base, page, baud = int(base_hex, 0), int(page), int(baud)
+    mega = mcu.startswith("atmega")
+    # The m48s are megas without a boot section: patched vector, no fuse
+    # preflight, and the same reset-to-0 the tinies get.
+    patch = not mega or mcu.startswith("atmega48")
+    reset_hex = "0" if mega else None  # the boot-sectioned mega runs BOOTRST-unprogrammed here
+    sys.path.insert(0, os.path.dirname(os.path.abspath(tool)))
+    sys.path.insert(0, os.path.dirname(os.path.abspath(__file__)))
+    import pbsim
+    import pureboot as pb
+
+    slot = pb.SLOT
+    os.makedirs(workdir, exist_ok=True)
+    objcopy = os.environ.get("PB_OBJCOPY", "avr-objcopy")
+    images = {}
+    for name, source in (("v0", elf), ("v9", update_elf)):
+        path = os.path.join(workdir, name + ".bin")
+        subprocess.run([objcopy, "-O", "binary", source, path], check=True)
+        images[name] = open(path, "rb").read()
+    if images["v0"] == images["v9"]:
+        fail("the update image is byte-identical to the resident build")
+    dump = os.path.join(workdir, "dump.bin")
+    state = os.path.join(workdir, "update.pbstate")
+    fuses = assumed_fuses(pb, images["v0"]) if mega and not patch else None
+
+    def connect(device):
+        port = pb.Port(device.pty, baud)
+        if mega:
+            # Reset boots the application here; its 'L' is the loader entry.
+            # To a live loader the same byte is an ignored command.
+            port.read_available(0.5)
+            port.write(b"L")
+        loader = pb.Loader(port)
+        loader.connect(25)
+        return port, loader
+
+    def padded(image):
+        return image + b"\xff" * (slot - len(image))
+
+    def resident_bytes(loader):
+        return loader.read_flash(base, slot)
+
+    def assert_state(loader, image, app_pages):
+        if resident_bytes(loader) != padded(image):
+            fail("resident loader does not match the update image")
+        stage = base - slot
+        got = loader.read_flash(stage, slot)
+        for address, data in app_pages.items():
+            if stage <= address < base:
+                if got[address - stage : address - stage + page] != data:
+                    fail(f"staging region page {address:#06x} not restored")
+
+    device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump, reset_hex=reset_hex)
+    final = "v0"
+    try:
+        # The application first — its planner output is the restore truth.
+        pbsim.run_tool(tool, device.pty, baud, "--flash", app_bin, "--stay")
+        port, loader = connect(device)
+        app_pages = pb.plan_flash(open(app_bin, "rb").read(), loader.info)
+        port.close()
+
+        # A clean CLI update, resident -> v9.
+        args = ["--update-loader", os.path.join(workdir, "v9.bin"), "--state", state, "--stay"]
+        if fuses:
+            args += ["--assume-fuses", fuses.hex()]
+        out = pbsim.run_tool(tool, device.pty, baud, *args)
+        if "loader updated" not in out:
+            fail("update did not report success")
+        if os.path.exists(state):
+            fail("state file survived a completed update")
+        port, loader = connect(device)
+        assert_state(loader, images["v9"], app_pages)
+        loader.run_application()
+        if port.read_exact(3, 5.0) != b"APP":
+            fail("application does not banner after the update")
+        port.close()
+        final = "v9"
+        print("clean update: resident replaced, staging restored, application intact")
+
+        # Power-fail rehearsal: kill mid-phase, restart from the dump,
+        # re-run, and the update must still complete. Each round flips the
+        # direction so the flash is never already at its target. The mega's
+        # mid-resident-rewrite loss is exercised as a host crash instead:
+        # with BOOTRST unprogrammed and the resident mid-erase, a power loss
+        # there has no reset path into the staging copy — the documented
+        # cost of that profile (README).
+        for kill_region, kill_hits, kill_device in (
+            ("stage", 2, True),
+            ("resident", 1, patch),
+            ("stage_restore", 2, True),
+        ):
+            device.reset()  # the previous round left the application running
+            port, loader = connect(device)
+            target = "v9" if resident_bytes(loader) == padded(images["v0"]) else "v0"
+            image_path = os.path.join(workdir, target + ".bin")
+            injected = make_fault_loader(pb, base, slot, kill_region, kill_hits, device if kill_device else None)(port)
+            injected.info = loader.info
+            try:
+                pb.op_update_loader(injected, 25, image_path, state, fuses)
+                fail(f"{kill_region}: fault never triggered")
+            except PowerFail as event:
+                print(f"power fail injected: {event}")
+            port.close()
+            if kill_device:
+                device = pbsim.Device(device_bin, elf, mcu, hz, base_hex, page, baud, dump,
+                                      reset_hex=reset_hex, resume=dump)
+            port, loader = connect(device)
+            pb.op_update_loader(loader, 25, image_path, state, fuses)
+            assert_state(loader, images[target], app_pages)
+            loader.run_application()
+            if port.read_exact(3, 5.0) != b"APP":
+                fail(f"{kill_region}: application lost after the resumed update")
+            port.close()
+            final = target
+            print(f"resumed after {kill_region} loss: update completed, application intact")
+    finally:
+        device.stop()
+
+    # Ground truth: the simulator's own flash against the final state, and
+    # on the patched-vector chips an independent decode of the reset routing.
+    flash = open(dump, "rb").read()
+    if flash[base : base + slot] != padded(images[final]):
+        fail("ground-truth resident region does not match the final image")
+    if patch:
+        flash_words = (base + slot) // 2
+        word0 = flash[0] | (flash[1] << 8)
+        if rjmp_decode(word0, 0, flash_words) != base // 2:
+            fail("ground-truth reset vector does not land on the loader")
+        app = open(app_bin, "rb").read()
+        trampoline = flash[base - 2] | (flash[base - 1] << 8)
+        if rjmp_decode(trampoline, (base - 2) // 2, flash_words) != rjmp_decode(app[0] | (app[1] << 8), 0, flash_words):
+            fail("ground-truth trampoline does not land on the application entry")
+    print("pbupdate: clean update + all power-fail phases recovered")
+
+
+if __name__ == "__main__":
+    main()

test/pureboot_device.c

@@ -0,0 +1,461 @@
+// simavr "device" for the pureboot protocol tests, every chip. Loads the
+// boot-linked ELF at the loader base, starts execution there (BOOTRST / the
+// patched vector are not what is under test), and exposes the loader's
+// serial link as a pty for the real host tool:
+//
+//   - Hardware USART builds: simavr's uart_pty on the selected instance.
+//   - Software UART builds: an 8N1 bridge between a pty and the GPIO pins,
+//     timed against the simulated cycle counter (drives the loader's RX,
+//     decodes its TX).
+//
+// The link follows the chip's natural default (USART0 on the megas, the
+// software UART on PB0/PB1 elsewhere) unless -l overrides it: `-l usart1`
+// for the second instance, `-l sw:B5,B1` for a software build's RX,TX pins.
+//
+// simavr's tiny cores decode the SPM opcode but attach no NVM module — SPM
+// is a silent no-op (the mega's boot section has one, avr_flash). The
+// missing module is supplied here: the SPM ioctl reads SPMCSR/Z/r1:r0 and
+// implements buffer fill, page erase, page write, and CTPB, completing
+// instantly. RFLB's LPM diversion (fuse readout) stays unmodeled, so the
+// 'F' command answers with flash bytes — the tests assert transport only.
+//
+// On exit (or SIGTERM) the flash and EEPROM are dumped to files for a
+// ground-truth cross-check against what the host read back.
+#include <fcntl.h>
+#include <pty.h>
+#include <signal.h>
+#include <stdint.h>
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include <termios.h>
+#include <unistd.h>
+
+#include "avr_eeprom.h"
+#include "avr_flash.h"
+#include "avr_ioport.h"
+#include "avr_uart.h"
+#include "sim_avr.h"
+#include "sim_elf.h"
+#include "sim_io.h"
+#include "uart_pty.h"
+
+static avr_t *avr;
+static uart_pty_t uart_pty;
+static int link_software;
+static char uart_digit = '0';
+static char sw_rx_port = 'B', sw_tx_port = 'B';
+static int sw_rx_bit = 0, sw_tx_bit = 1;
+static const char *dump_path;
+static uint32_t reset_pc;
+static volatile sig_atomic_t reset_requested;
+
+static int parse_link(const char *spec)
+{
+	if (strcmp(spec, "usart0") == 0 || strcmp(spec, "usart1") == 0) {
+		link_software = 0;
+		uart_digit = spec[5];
+		return 0;
+	}
+	if (strncmp(spec, "sw", 2) == 0) {
+		link_software = 1;
+		if (spec[2] == '\0')
+			return 0;
+		if (sscanf(spec + 2, ":%c%d,%c%d", &sw_rx_port, &sw_rx_bit, &sw_tx_port, &sw_tx_bit) == 4)
+			return 0;
+	}
+	return -1;
+}
+
+// simavr 1.6's avr_flash PGERS handler erases spm_pagesize bytes starting at
+// Z & ~1 instead of the page containing Z (its PGWRT path masks correctly) —
+// hardware ignores the in-page bits (§26.8.1), so an erase issued with Z
+// anywhere inside the page wipes half the neighbouring page in simulation
+// only. Wrap the mega's registered flash ioctl and re-dispatch page erases
+// with Z forced to the page boundary; everything else passes through.
+//
+// A second gap on the boot-section-less m48s: their RWWSRE bit is the
+// temporary-buffer discard (Atmel-8271 §26.2/§26.3.1), but the stock model
+// gates its RWWSRE branch on AVR_SELFPROG_HAVE_RWW — absent on the m48
+// core — so the discard store falls through into the buffer-fill branch and
+// plants whatever Z/R1:R0 happen to hold. Perform the silicon's discard
+// here instead.
+static avr_flash_t *mega_flash;
+static int (*mega_flash_ioctl)(avr_io_t *io, uint32_t ctl, void *param);
+
+static int fixed_flash_ioctl(avr_io_t *io, uint32_t ctl, void *param)
+{
+	if (ctl == AVR_IOCTL_FLASH_SPM && avr_regbit_get(io->avr, mega_flash->pgers)) {
+		uint16_t z = (uint16_t)(io->avr->data[30] | (io->avr->data[31] << 8));
+		uint16_t masked = (uint16_t)(z & ~(mega_flash->spm_pagesize - 1));
+		io->avr->data[30] = (uint8_t)masked;
+		io->avr->data[31] = (uint8_t)(masked >> 8);
+		int result = mega_flash_ioctl(io, ctl, param);
+		io->avr->data[30] = (uint8_t)z;
+		io->avr->data[31] = (uint8_t)(z >> 8);
+		return result;
+	}
+	if (ctl == AVR_IOCTL_FLASH_SPM && !(mega_flash->flags & AVR_SELFPROG_HAVE_RWW) &&
+	    (io->avr->data[mega_flash->r_spm] & 0x11) == 0x11) { // RWWSRE|SELFPRGEN: the m48 buffer discard
+		for (int i = 0; i < mega_flash->spm_pagesize / 2; i++) {
+			mega_flash->tmppage[i] = 0xffff;
+			mega_flash->tmppage_used[i] = 0;
+		}
+		avr_regbit_clear(io->avr, mega_flash->selfprgen);
+		return 0;
+	}
+	return mega_flash_ioctl(io, ctl, param);
+}
+
+static void fix_mega_flash_erase(void)
+{
+	for (avr_io_t *io = avr->io_port; io; io = io->next) {
+		if (io->kind && strcmp(io->kind, "flash") == 0) {
+			mega_flash = (avr_flash_t *)io;
+			mega_flash_ioctl = io->ioctl;
+			io->ioctl = fixed_flash_ioctl;
+			return;
+		}
+	}
+	fprintf(stderr, "device: no flash module to fix — SPM page erases may misalign\n");
+}
+
+static void request_reset(int sig)
+{
+	(void)sig;
+	reset_requested = 1;
+}
+
+// ------------------------------------------------------------- tiny NVM ---
+
+typedef struct {
+	avr_io_t io;
+	uint8_t buffer[128];
+	uint8_t used[128]; // a buffer word loads once until erased — like silicon
+	unsigned page;
+} tiny_nvm_t;
+
+static tiny_nvm_t nvm;
+
+static int nvm_ioctl(avr_io_t *io, uint32_t ctl, void *param)
+{
+	(void)param;
+	if (ctl != AVR_IOCTL_FLASH_SPM)
+		return -1;
+	tiny_nvm_t *n = (tiny_nvm_t *)io;
+	avr_t *mcu = io->avr;
+	uint8_t command = mcu->data[0x57] & 0x1f; // SPMCSR, both tinies
+	uint16_t z = (uint16_t)(mcu->data[30] | (mcu->data[31] << 8));
+	uint32_t page_base = (uint32_t)(z & ~(n->page - 1)) % (mcu->flashend + 1);
+	if (command == 0x01) { // SPMEN alone: buffer fill from r1:r0
+		unsigned offset = z & (n->page - 1) & ~1u;
+		if (!n->used[offset]) { // first write wins until the buffer clears
+			n->buffer[offset] = mcu->data[0];
+			n->buffer[offset + 1] = mcu->data[1];
+			n->used[offset] = 1;
+		}
+	} else if (command == 0x03) { // PGERS
+		memset(mcu->flash + page_base, 0xff, n->page);
+	} else if (command == 0x05) { // PGWRT: programming only clears bits
+		for (unsigned i = 0; i < n->page; i++)
+			mcu->flash[page_base + i] &= n->buffer[i];
+		memset(n->buffer, 0xff, n->page);
+		memset(n->used, 0, n->page);
+	} else if (command == 0x11) { // CTPB
+		memset(n->buffer, 0xff, n->page);
+		memset(n->used, 0, n->page);
+	}
+	mcu->data[0x57] &= (uint8_t)~0x1f; // the operation completes instantly
+	return 0;
+}
+
+// ----------------------------------------------------------- GPIO bridge ---
+
+static int pty_master = -1;
+static avr_irq_t *rx_pin; // the loader's RX (PB0), driven from the pty
+static avr_cycle_count_t bit_cycles;
+
+static int tx_level = 1, tx_active, tx_bit;
+static uint8_t tx_shift;
+
+static avr_cycle_count_t tx_sample(avr_t *mcu, avr_cycle_count_t when, void *param)
+{
+	(void)mcu;
+	(void)param;
+	tx_shift = (uint8_t)((tx_shift >> 1) | (tx_level ? 0x80 : 0));
+	if (++tx_bit < 8)
+		return when + bit_cycles;
+	if (write(pty_master, &tx_shift, 1) != 1)
+		fprintf(stderr, "device: pty write lost a byte\n");
+	tx_active = 0;
+	return 0;
+}
+
+static void tx_hook(avr_irq_t *irq, uint32_t value, void *param)
+{
+	(void)irq;
+	(void)param;
+	int level = value & 1;
+	if (!tx_active && tx_level == 1 && level == 0) { // start edge
+		tx_active = 1;
+		tx_bit = 0;
+		avr_cycle_timer_register(avr, bit_cycles + bit_cycles / 2, tx_sample, NULL);
+	}
+	tx_level = level;
+}
+
+static uint8_t rx_queue[8192];
+static unsigned rx_head, rx_tail; // ring: head = next to send
+static int rx_active, rx_bit;
+static uint8_t rx_byte;
+
+static void rx_start_next(void);
+
+static avr_cycle_count_t rx_step(avr_t *mcu, avr_cycle_count_t when, void *param)
+{
+	(void)mcu;
+	(void)param;
+	if (rx_bit < 8) {
+		avr_raise_irq(rx_pin, (rx_byte >> rx_bit) & 1);
+		rx_bit++;
+		return when + bit_cycles;
+	}
+	if (rx_bit == 8) { // stop bit, plus one idle bit of margin
+		avr_raise_irq(rx_pin, 1);
+		rx_bit++;
+		return when + 2 * bit_cycles;
+	}
+	rx_active = 0;
+	rx_start_next();
+	return 0;
+}
+
+static void rx_start_next(void)
+{
+	if (rx_active || rx_head == rx_tail)
+		return;
+	rx_byte = rx_queue[rx_head];
+	rx_head = (rx_head + 1) % sizeof(rx_queue);
+	rx_active = 1;
+	rx_bit = 0;
+	avr_raise_irq(rx_pin, 0); // start bit
+	avr_cycle_timer_register(avr, bit_cycles, rx_step, NULL);
+}
+
+// A reset abandons whatever the bridge was mid-transfer: bytes still queued
+// for a chip that no longer has the context to receive them meaningfully,
+// and a decode in progress on a TX line the reset may have already changed.
+// The pending cycle timers must go with the state: avr_reset drops the TX
+// output latch, whose falling edge starts a spurious decode before this
+// runs, and a stale tx_sample would then interleave with the loader's first
+// real answer through the shared shift state, corrupting it.
+static void bridge_reset(void)
+{
+	avr_cycle_timer_cancel(avr, tx_sample, NULL);
+	avr_cycle_timer_cancel(avr, rx_step, NULL);
+	rx_head = rx_tail = 0;
+	rx_active = 0;
+	tx_active = 0;
+	tx_level = 1;
+	avr_raise_irq(rx_pin, 1); // idle line
+}
+
+static void poll_pty(void)
+{
+	uint8_t chunk[256];
+	ssize_t got = read(pty_master, chunk, sizeof(chunk));
+	for (ssize_t i = 0; i < got; i++) {
+		unsigned next = (rx_tail + 1) % sizeof(rx_queue);
+		if (next == rx_head)
+			break; // full: the host will retry on timeout
+		rx_queue[rx_tail] = chunk[i];
+		rx_tail = next;
+	}
+	if (got > 0)
+		rx_start_next();
+}
+
+// ------------------------------------------------------------------ main ---
+
+static void finish(int sig)
+{
+	(void)sig;
+	if (dump_path) {
+		FILE *f = fopen(dump_path, "wb");
+		if (f) {
+			fwrite(avr->flash, 1, avr->flashend + 1, f);
+			fclose(f);
+		}
+		avr_eeprom_desc_t ee = {.ee = NULL, .offset = 0, .size = 0};
+		if (avr_ioctl(avr, AVR_IOCTL_EEPROM_GET, &ee) == 0 && ee.ee && ee.size) {
+			char path[512];
+			snprintf(path, sizeof(path), "%s.eeprom", dump_path);
+			f = fopen(path, "wb");
+			if (f) {
+				fwrite(ee.ee, 1, ee.size, f);
+				fclose(f);
+			}
+		}
+	}
+	if (!link_software)
+		uart_pty_stop(&uart_pty);
+	_exit(0);
+}
+
+int main(int argc, char *argv[])
+{
+	int link_given = 0;
+	for (int opt; (opt = getopt(argc, argv, "l:")) != -1;) {
+		if (opt != 'l' || parse_link(optarg) != 0) {
+			fprintf(stderr, "device: bad link spec (usart0, usart1, sw, or sw:B0,B1 as RX,TX)\n");
+			return 2;
+		}
+		link_given = 1;
+	}
+	int args = argc - optind;
+	if (args < 7 || args > 9) {
+		fprintf(stderr,
+		        "usage: %s [-l link] <pureboot.elf> <mcu> <hz> <base_hex> <page> <baud> <flash_dump>"
+		        " [reset_hex] [resume_flash]\n"
+		        "  -l link:      usart0 | usart1 | sw[:B0,B1] (RX,TX); default: the chip's own\n"
+		        "  reset_hex:    reset vector (default: base with a boot section, else 0)\n"
+		        "  resume_flash: raw full-flash image loaded instead of the ELF — a prior\n"
+		        "                run's dump, for power-fail resume tests\n",
+		        argv[0]);
+		return 2;
+	}
+	argv += optind - 1; // argv[1] is the ELF again, whatever was parsed
+	const char *mcu_name = argv[2];
+	uint32_t base = (uint32_t)strtoul(argv[4], NULL, 0);
+	unsigned page = (unsigned)atoi(argv[5]);
+	unsigned baud = (unsigned)atoi(argv[6]);
+	dump_path = argv[7];
+	int is_mega = strncmp(mcu_name, "atmega", 6) == 0;
+	if (!link_given)
+		link_software = !is_mega; // the chips' natural links: USART0, or PB0/PB1
+
+	avr = avr_make_mcu_by_name(mcu_name);
+	if (!avr) {
+		fprintf(stderr, "device: no %s core\n", mcu_name);
+		return 1;
+	}
+	avr_init(avr);
+	avr->frequency = (uint32_t)strtoul(argv[3], NULL, 0);
+	memset(avr->flash, 0xff, avr->flashend + 1); // real flash powers up erased
+
+	if (args > 8) {
+		// Resume: the full flash image of an interrupted prior run.
+		FILE *f = fopen(argv[9], "rb");
+		if (!f || fread(avr->flash, 1, avr->flashend + 1, f) == 0) {
+			fprintf(stderr, "device: cannot read %s\n", argv[9]);
+			return 1;
+		}
+		fclose(f);
+	} else {
+		elf_firmware_t fw = {0};
+		if (elf_read_firmware(argv[1], &fw) != 0) {
+			fprintf(stderr, "device: cannot read %s\n", argv[1]);
+			return 1;
+		}
+		memcpy(avr->flash + base, fw.flash, fw.flashsize);
+	}
+	// The boot-sectioned megas enter the loader in hardware (BOOTRST, not
+	// modeled — the argument picks the modeled fuse's target); the tinies
+	// and the boot-section-less m48s reset to word 0 like silicon — erased
+	// flash walks up into the loader, and after the host's surgery the
+	// patched vector routes there.
+	int boot_section = is_mega && strncmp(mcu_name, "atmega48", 8) != 0;
+	reset_pc = args > 7 ? (uint32_t)strtoul(argv[8], NULL, 0) : (boot_section ? base : 0);
+	avr->pc = reset_pc;
+	avr->codeend = avr->flashend;
+
+	// Erased EEPROM, as hardware powers up (simavr zeroes it).
+	uint8_t blank[1024];
+	memset(blank, 0xff, sizeof(blank));
+	avr_eeprom_desc_t seed = {.ee = blank, .offset = 0, .size = 0};
+	if (avr_ioctl(avr, AVR_IOCTL_EEPROM_GET, &seed) == 0 && seed.size <= sizeof(blank)) {
+		seed.ee = blank;
+		avr_ioctl(avr, AVR_IOCTL_EEPROM_SET, &seed);
+	}
+
+	// The megas carry simavr's avr_flash module (and its two gaps the wrap
+	// above fixes); the tinies get the NVM module simavr lacks. Which serial
+	// bridge runs is the link's business, not the chip class's.
+	if (is_mega) {
+		fix_mega_flash_erase();
+	} else {
+		nvm.page = page;
+		memset(nvm.buffer, 0xff, sizeof(nvm.buffer));
+		nvm.io.kind = "tiny_nvm";
+		nvm.io.ioctl = nvm_ioctl;
+		avr_register_io(avr, &nvm.io);
+	}
+
+	if (!link_software) {
+		// POLL_SLEEP paces an idle-polling loader in host real time (a
+		// no-hardware CPU-saving hack); clear it so cycles run free.
+		uint32_t flags = 0;
+		avr_ioctl(avr, AVR_IOCTL_UART_GET_FLAGS(uart_digit), &flags);
+		flags &= ~AVR_UART_FLAG_POLL_SLEEP;
+		avr_ioctl(avr, AVR_IOCTL_UART_SET_FLAGS(uart_digit), &flags);
+		uart_pty_init(avr, &uart_pty);
+		uart_pty_connect(&uart_pty, uart_digit);
+		printf("PB_PTY %s\n", uart_pty.pty.slavename);
+	} else {
+		bit_cycles = (avr->frequency + baud / 2) / baud; // matches uart.hpp's own rounding exactly
+		rx_pin = avr_io_getirq(avr, AVR_IOCTL_IOPORT_GETIRQ(sw_rx_port), (unsigned)sw_rx_bit);
+		avr_irq_register_notify(avr_io_getirq(avr, AVR_IOCTL_IOPORT_GETIRQ(sw_tx_port), (unsigned)sw_tx_bit), tx_hook,
+		                        NULL);
+		avr_raise_irq(rx_pin, 1); // idle line
+
+		int slave;
+		struct termios raw;
+		cfmakeraw(&raw);
+		if (openpty(&pty_master, &slave, NULL, &raw, NULL) != 0) {
+			fprintf(stderr, "device: openpty failed\n");
+			return 1;
+		}
+		fcntl(pty_master, F_SETFL, O_NONBLOCK);
+		printf("PB_PTY %s\n", ttyname(slave));
+	}
+	fflush(stdout);
+
+	signal(SIGTERM, finish);
+	signal(SIGINT, finish);
+	signal(SIGUSR1, request_reset); // an external reset line, for the tests
+
+	long since_poll = 0;
+	for (;;) {
+		int state = avr_run(avr);
+		if (state == cpu_Done || state == cpu_Crashed)
+			break;
+		if (reset_requested) {
+			reset_requested = 0;
+			avr_reset(avr);
+			avr->pc = reset_pc;
+			if (!link_software) { // reset restores the pacing hack; re-clear it
+				uint32_t flags = 0;
+				avr_ioctl(avr, AVR_IOCTL_UART_GET_FLAGS(uart_digit), &flags);
+				flags &= ~AVR_UART_FLAG_POLL_SLEEP;
+				avr_ioctl(avr, AVR_IOCTL_UART_SET_FLAGS(uart_digit), &flags);
+			} else {
+				bridge_reset();
+			}
+		}
+		if (link_software && ++since_poll >= 2000) {
+			since_poll = 0;
+			poll_pty();
+			// An unthrottled idle simulation runs the activation window out
+			// from under the host's real-time knock cadence: a 1 MHz build's
+			// 8 s window is 8 M cycles — tens of wall milliseconds — so a
+			// first knock lost to an in-flight reset misses the window
+			// entirely. Pace the simulation only while the bridge is fully
+			// quiet (nothing decoding, nothing queued); transfers keep full
+			// speed, and a quiet window stretches toward real time.
+			if (!rx_active && !tx_active && rx_head == rx_tail)
+				usleep(200);
+		}
+	}
+	finish(0);
+	return 0;
+}

test/test_planner.py

@@ -0,0 +1,287 @@
+#!/usr/bin/env python3
+"""Host-tool unit tests — the planning and policy logic, no simulator:
+programming orders and their recovery properties, the reset-vector surgery,
+the staging composition, the boot-fuse decode, and the update preflight over
+fuse combinations simavr cannot model.
+
+Usage: test_planner.py <tool_py>
+"""
+
+import sys
+
+
+def fail(message):
+    print(f"FAIL: {message}")
+    sys.exit(1)
+
+
+def expect_error(what, fn, *needles):
+    try:
+        fn()
+    except Exception as error:
+        for needle in needles:
+            if needle not in str(error):
+                fail(f"{what}: error lacks {needle!r}: {error}")
+        return
+    fail(f"{what}: no error raised")
+
+
+def info_of(pb, base, page, patch, flash, signature=(0x1E, 0x93, 0x0B), word_flash=False, version=None):
+    scale = 2 if word_flash else 1
+    wire_base = base // scale
+    flags = (1 if patch else 0) | (2 if word_flash else 0)
+    raw = bytes((0x50, 0x42, pb.NEWEST_LOADER if version is None else version,
+                 *signature, page & 0xFF, wire_base & 0xFF, wire_base >> 8, 0, 2, flags))
+    info = pb.Info(raw)
+    if info.flash_size != flash:
+        fail(f"info_of({base:#x}) decodes to {info.flash_size:#x} of flash, not {flash:#x}")
+    return info
+
+
+def rjmp_decode(word, at, flash_words):
+    if word & 0xF000 != 0xC000:
+        fail(f"not an rjmp: {word:#06x}")
+    offset = word & 0x0FFF
+    if offset >= 0x800:
+        offset -= 0x1000
+    return (at + 1 + offset) % flash_words
+
+
+def main():
+    import os
+    sys.path.insert(0, os.path.dirname(os.path.abspath(sys.argv[1])))
+    import pureboot as pb
+
+    tiny = info_of(pb, 0x1E00, 64, True, 0x2000)
+    mega = info_of(pb, 0x7E00, 128, False, 0x8000, signature=(0x1E, 0x95, 0x0F))
+
+    # Versioning: the block's third byte is the loader's version, and the tool
+    # speaks a window of them. Every version in the window decodes, so an older
+    # deployed loader stays usable; one above the window is refused by name,
+    # since which version changed the protocol is knowledge only the tool
+    # holds, and it holds none about a version it has never heard of.
+    for version in range(pb.OLDEST_LOADER, pb.NEWEST_LOADER + 1):
+        if info_of(pb, 0x1E00, 64, True, 0x2000, version=version).version != version:
+            fail(f"pureboot {version} does not decode")
+    expect_error(
+        "unknown loader version",
+        lambda: info_of(pb, 0x1E00, 64, True, 0x2000, version=pb.NEWEST_LOADER + 1),
+        f"pureboot {pb.NEWEST_LOADER + 1}",
+        "newer tool",
+    )
+
+    # mega_boot: BOOTSZ words and the BOOTRST sense per chip — the fuse byte
+    # index (EXTENDED on the x8 line except the m328s' HIGH, HIGH elsewhere)
+    # and the per-family ladders (Atmel-2486/2466/2503/2545/8271/DS40002065/
+    # 8272/8011/2593/42719). Synthetic 'F' replies: only the boot byte
+    # carries meaning.
+    cases = (
+        ((0x1E, 0x93, 0x07), 0x2000, 3, {0b11: 0x1F00, 0b10: 0x1E00, 0b01: 0x1C00, 0b00: 0x1800}),  # m8
+        ((0x1E, 0x94, 0x03), 0x4000, 3, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}),  # m16
+        ((0x1E, 0x95, 0x02), 0x8000, 3, {0b11: 0x7E00, 0b10: 0x7C00, 0b01: 0x7800, 0b00: 0x7000}),  # m32
+        ((0x1E, 0x93, 0x0A), 0x2000, 2, {0b11: 0x1F00, 0b10: 0x1E00, 0b01: 0x1C00, 0b00: 0x1800}),  # m88
+        ((0x1E, 0x93, 0x0F), 0x2000, 2, {0b11: 0x1F00, 0b10: 0x1E00, 0b01: 0x1C00, 0b00: 0x1800}),  # m88P
+        ((0x1E, 0x94, 0x06), 0x4000, 2, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}),  # m168/168A
+        ((0x1E, 0x94, 0x0B), 0x4000, 2, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}),  # m168P
+        ((0x1E, 0x95, 0x14), 0x8000, 3, {0b11: 0x7E00, 0b10: 0x7C00, 0b01: 0x7800, 0b00: 0x7000}),  # m328
+        ((0x1E, 0x95, 0x0F), 0x8000, 3, {0b11: 0x7E00, 0b10: 0x7C00, 0b01: 0x7800, 0b00: 0x7000}),  # m328P
+        ((0x1E, 0x94, 0x0F), 0x4000, 3, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}),  # m164A
+        ((0x1E, 0x94, 0x0A), 0x4000, 3, {0b11: 0x3F00, 0b10: 0x3E00, 0b01: 0x3C00, 0b00: 0x3800}),  # m164P
+        ((0x1E, 0x95, 0x15), 0x8000, 3, {0b11: 0x7E00, 0b10: 0x7C00, 0b01: 0x7800, 0b00: 0x7000}),  # m324A
+        ((0x1E, 0x96, 0x09), 0x10000, 3, {0b11: 0xFC00, 0b10: 0xF800, 0b01: 0xF000, 0b00: 0xE000}),  # m644
+        ((0x1E, 0x96, 0x0A), 0x10000, 3, {0b11: 0xFC00, 0b10: 0xF800, 0b01: 0xF000, 0b00: 0xE000}),  # m644P
+        ((0x1E, 0x97, 0x06), 0x20000, 3, {0b11: 0x1FC00, 0b10: 0x1F800, 0b01: 0x1F000, 0b00: 0x1E000}),  # 1284
+        ((0x1E, 0x97, 0x05), 0x20000, 3, {0b11: 0x1FC00, 0b10: 0x1F800, 0b01: 0x1F000, 0b00: 0x1E000}),  # 1284P
+    )
+    for signature, flash, which, ladder in cases:
+        chip = info_of(pb, flash - pb.SLOT, 128 if flash < 0x20000 else 0, False, flash,
+                       signature=signature, word_flash=flash > 0x10000)
+        for bits, start in ladder.items():
+            fuses = bytearray((0xFF, 0xFF, 0xFF, 0xFF))
+            fuses[which] = (0xF8 | (bits << 1)) & ~1
+            prog, at = pb.mega_boot(chip, bytes(fuses))
+            if not prog or at != start:
+                fail(f"mega_boot {signature[1]:02x}{signature[2]:02x} BOOTSZ={bits:02b} programmed: {prog} {at:#07x}")
+            fuses[which] |= 1
+            prog, at = pb.mega_boot(chip, bytes(fuses))
+            if prog or at != start:
+                fail(f"mega_boot {signature[1]:02x}{signature[2]:02b} unprogrammed: {prog} {at:#07x}")
+
+    # Word-addressed info decode: the 1284P's base and page ride the wire
+    # scaled — a 17-bit base halved into the block's two bytes, a 256-byte page
+    # spelled 0 — and its slot is the same 512 bytes as everywhere else, so its
+    # staging slot lands inside the 1 KiB minimum boot section.
+    big = info_of(pb, 0x1FE00, 0, False, 0x20000, signature=(0x1E, 0x97, 0x05), word_flash=True)
+    if big.page != 256 or big.base != 0x1FE00 or big.stage != 0x1FC00:
+        fail(f"word-addressed info decode: page {big.page}, base {big.base:#x}, stage {big.stage:#x}")
+
+    # Surgery: word 0 lands on the loader, the trampoline on the original
+    # entry — checked with an independent decoder.
+    app = bytes((0xC0 | 0x00, 0xC0)) + bytes((0x12,)) * 300  # rjmp .+0x00C0... entry word 0xC0C0
+    entry = rjmp_decode(app[0] | (app[1] << 8), 0, tiny.flash_size // 2)
+    pages = pb.plan_flash(app, tiny)
+    word0 = pages[0][0] | (pages[0][1] << 8)
+    if rjmp_decode(word0, 0, tiny.flash_size // 2) != tiny.base // 2:
+        fail("surgery: patched word 0 misses the loader")
+    tp = pages[tiny.base - 64]
+    tramp = tp[62] | (tp[63] << 8)
+    if rjmp_decode(tramp, (tiny.base - 2) // 2, tiny.flash_size // 2) != entry:
+        fail("surgery: trampoline misses the original entry")
+    expect_error("non-rjmp vector", lambda: pb.plan_flash(bytes((0x0C, 0x94)) + app[2:], tiny), "not an rjmp")
+    looped = bytearray(app)
+    word = pb.rjmp_to(0, tiny.base // 2, tiny.flash_size // 2)
+    looped[0], looped[1] = word & 0xFF, word >> 8
+    expect_error("read-back image", lambda: pb.plan_flash(bytes(looped), tiny), "read-back")
+    expect_error("oversize image", lambda: pb.plan_flash(bytes(0x1DFF), tiny), "application flash ends")
+
+    # Ordering: patched vector puts page 0 first and the trampoline second;
+    # a boot section puts page 0 last. Blank pages drop only when erased.
+    order = pb.covered(pages, tiny, skip_blank=False)
+    if order[0] != 0 or order[1] != tiny.base - 64:
+        fail(f"tiny order starts {order[:2]}, want page 0 then trampoline page")
+    if sorted(order[2:]) != order[2:]:
+        fail("tiny order tail not ascending")
+    mega_pages = pb.plan_flash(bytes((0xFF,)) * 600, mega)
+    morder = pb.covered(mega_pages, mega, skip_blank=False)
+    if morder[-1] != 0 or sorted(morder[:-1]) != morder[:-1]:
+        fail(f"mega order {morder}, want ascending with page 0 last")
+    blanky = {0: pages[0], 64: bytes((0xFF,)) * 64, 128: pages[128], tiny.base - 64: tp}
+    slim = pb.covered(blanky, tiny, skip_blank=True)
+    if 64 in slim or 0 not in slim or tiny.base - 64 not in slim:
+        fail(f"skip_blank order wrong: {slim}")
+
+    # Staging content: the identical image plus the through-word on a
+    # patched-vector chip; hard size clamps either way.
+    image = bytes(range(256)) * 2  # 512 B — too big for a tiny slot
+    expect_error("tiny staging size", lambda: pb.staging_content(image, tiny), "510")
+    staged = pb.staging_content(image[:508], tiny)
+    through = staged[510] | (staged[511] << 8)
+    if rjmp_decode(through, (tiny.base - 2) // 2, tiny.flash_size // 2) != tiny.base // 2:
+        fail("through-word misses the resident base")
+    if pb.staging_content(image, mega) != image:
+        fail("mega staging content should be the bare image")
+    expect_error("mega staging size", lambda: pb.staging_content(image + b"!", mega), "512")
+
+    # The embedded info block: found in a synthetic binary, absent in noise.
+    binary = bytes((0xAA,)) * 10 + tiny.raw + bytes((0xBB,)) * 10
+    found = pb.image_info(binary)
+    if found is None or found.raw != tiny.raw:
+        fail("image_info misses the embedded block")
+    if pb.image_info(bytes((0xAA,)) * 40) is not None:
+        fail("image_info invents a block")
+    # An older loader's image stays readable, so a deployed build can be
+    # identified and installed like any other.
+    old = info_of(pb, 0x1E00, 64, True, 0x2000, version=pb.OLDEST_LOADER)
+    found_old = pb.image_info(bytes((0xAA,)) * 10 + old.raw)
+    if found_old is None or found_old.version != pb.OLDEST_LOADER:
+        fail("image_info misses an older loader's block")
+
+    # loader_image must peel a padded image down to the slot content: a raw
+    # .bin padded from address 0 (or a whole-flash read-back with the loader
+    # resident at base) yields the same bytes as the bare slot image.
+    import tempfile
+    slot_image = bytes((0xAA,)) * 10 + tiny.raw + bytes((0xCC,)) * 40
+    padded = bytes((0xFF,)) * tiny.base + slot_image
+    with tempfile.NamedTemporaryFile(suffix=".bin", delete=False) as f:
+        f.write(padded)
+        padded_path = f.name
+    try:
+        if pb.loader_image(padded_path) != slot_image:
+            fail("loader_image does not peel a padded image to the slot content")
+    finally:
+        os.unlink(padded_path)
+
+    # Update preflight: the full fuse matrix, plus target mismatch.
+    other = info_of(pb, 0x1E00, 32, True, 0x2000)
+    expect_error("wrong-target image", lambda: pb.update_preflight(binary, other, None), "another target")
+    expect_error("mega needs fuses", lambda: pb.update_preflight(bytes((0xAA,)) * 8 + mega.raw, mega, None),
+                 "--assume-fuses")
+    mega_image = bytes((0xAA,)) * 8 + mega.raw
+
+    def fuses(high):
+        return bytes((0xFF, 0xFF, 0xFF, high))
+
+    expect_error("BOOTSZ 512 B", lambda: pb.update_preflight(mega_image, mega, fuses(0xFE)),
+                 "cannot self-update", "BOOTSZ")
+    notes = pb.update_preflight(mega_image, mega, fuses(0xFD))  # 1 KB, BOOTRST unprogrammed
+    if not any("BOOTRST unprogrammed" in n for n in notes):
+        fail(f"1K/unprogrammed notes: {notes}")
+    notes = pb.update_preflight(mega_image, mega, fuses(0xFC))  # 1 KB, BOOTRST programmed
+    if not any("staging slot" in n for n in notes):
+        fail(f"1K/programmed notes: {notes}")
+    notes = pb.update_preflight(mega_image, mega, fuses(0xFA))  # 2 KB, BOOTRST programmed
+    if not any("application flash" in n for n in notes):
+        fail(f"2K/programmed notes: {notes}")
+    if pb.update_preflight(bytes((0xAA,)) * 8 + tiny.raw, tiny, None) != []:
+        fail("tiny preflight should pass without fuses")
+
+    # The 1284s' smallest boot section (512 words) is exactly the resident
+    # slot plus its staging slot, so self-update is possible at the minimum
+    # BOOTSZ — no fuse step up, the 644's geometry. That holds only while a
+    # slot is 512 B: at 1 KiB the staging slot would fall outside the section
+    # and the preflight would refuse.
+    notes = pb.update_preflight(bytes((0xAA,)) * 8 + big.raw, big, fuses(0xFE))
+    if not any("staging slot" in n for n in notes):
+        fail(f"1284 minimum-BOOTSZ notes: {notes}")
+
+    # The walk-region refusal: BOOTRST aimed below the loader plus app data
+    # in the walk span errors without --force; erased spans and unprogrammed
+    # BOOTRST pass.
+    deep = {0x7800: bytes((1,)) * 128}
+    expect_error("walk region", lambda: pb.check_walk_region(deep, mega, fuses(0xFA), False), "--force")
+    pb.check_walk_region(deep, mega, fuses(0xFA), True)
+    pb.check_walk_region(deep, mega, fuses(0xFB), False)  # BOOTRST unprogrammed
+    pb.check_walk_region({0x7800: bytes((0xFF,)) * 128}, mega, fuses(0xFA), False)
+    pb.check_walk_region(deep, mega, None, False)  # fuses unknown: no check
+
+    # The repairing verify: a mismatched page is rewritten rather than raised,
+    # bounded so a fault that is not self-clearing cannot spin.
+    class FakeLoader:
+        """A device whose first `bad` writes of any page land wrong."""
+
+        def __init__(self, info, bad):
+            self.info = info
+            self.bad = bad
+            self.flash = {}
+            self.writes = 0
+
+        def write_page(self, address, data):
+            self.writes += 1
+            self.flash[address] = bytes(len(data)) if self.bad > 0 else bytes(data)
+            self.bad -= 1
+
+        def read_flash(self, address, count):
+            return self.flash.get(address, bytes(count))
+
+    want = {0: bytes((i * 5) & 0xFF for i in range(128))}
+
+    # One bad write, then good: repaired in place, and the caller never sees
+    # an error. The rewrite is counted, so a silent no-op cannot pass.
+    device = FakeLoader(info_of(pb, 0x7E00, 128, False, 0x8000), bad=1)
+    device.write_page(0, want[0])
+    pb.verify_pages(device, want, repair=True)
+    if device.writes != 2:
+        fail(f"repairing verify made {device.writes} writes, expected 2")
+
+    # Without repair the same state raises, so the repair is what fixed it.
+    device = FakeLoader(info_of(pb, 0x7E00, 128, False, 0x8000), bad=1)
+    device.write_page(0, want[0])
+    expect_error("verify without repair", lambda: pb.verify_pages(device, want), "verify failed")
+
+    # A page that never comes good stops after RETRIES rewrites, and says so.
+    device = FakeLoader(info_of(pb, 0x7E00, 128, False, 0x8000), bad=99)
+    device.write_page(0, want[0])
+    expect_error(
+        "unrepairable page",
+        lambda: pb.verify_pages(device, want, repair=True),
+        "verify failed",
+        f"after {pb.RETRIES} retries",
+    )
+    if device.writes != pb.RETRIES + 1:
+        fail(f"unrepairable page took {device.writes} writes, expected {pb.RETRIES + 1}")
+
+    print("test_planner: all planner and policy checks pass")
+
+
+if __name__ == "__main__":
+    main()

test/tsbtest.py

@@ -144,7 +144,7 @@ class Host:
         self._expect(CONFIRM, "C end")
         return echo
 
-    # Activation when the config page carries a password: 3x'@' then the
+    # Activation when the config page carries a password: 3×'@' then the
     # password bytes, then the info block + mainloop '!'.
     def activate_password(self, password):
         self.s.reset_input_buffer()
@@ -167,20 +167,6 @@ class Host:
         self._expect(CONFIRM, "emergency mainloop ready")
 
 
-    # A wrong password byte hangs the loader, still draining the line. Two
-    # things must not happen: it must not activate, and it must not fall
-    # through to the emergency erase - a byte the gate has already refused
-    # reaching the erase would let a guess wipe the part.
-    def refuse_password(self, byte):
-        self.s.reset_input_buffer()
-        self.s.write(bytes([KNOCK, KNOCK, KNOCK, byte]))
-        return self.s.read(1)
-
-    def say(self, byte):
-        self.s.write(bytes([byte]))
-        return self.s.read(1)
-
-
 def check(cond, msg):
     if not cond:
         raise AssertionError(msg)
@@ -195,7 +181,7 @@ PW_BYTES = bytes([0x50, 0x57])
 
 def scenario_roundtrip(host):
     """Activation + info block + flash/EEPROM/config read-write round-trips, on
-    a device with a blank (erased) config page - the usual no-password case."""
+    a device with a blank (erased) config page — the usual no-password case."""
     info = host.activate()
     check(info[0:3] == b"TSB", f"magic 'TSB' (got {info[0:3]!r})")
     check(info[6:9] == bytes([0x1E, 0x95, 0x0F]), f"signature 1E 95 0F (got {info[6:9].hex()})")
@@ -233,15 +219,6 @@ def scenario_emergency(host):
     check(host.read_eeprom(1) == b"\xff" * PAGE, "EEPROM wiped")
 
 
-def scenario_wrong_password(host):
-    """A wrong password byte neither activates the loader nor opens the
-    emergency erase behind it - the oracle carries a dedicated fix for the
-    second, and nothing here exercised either half."""
-    check(host.refuse_password(PW_BYTES[0] ^ 1) == b"", "a wrong password byte draws no reply")
-    check(host.say(0x00) == b"", "a 0 byte after it does not request the erase")
-    check(host.say(CONFIRM) == b"", "and neither does a confirm")
-
-
 def main():
     binary, elf, boot_base = sys.argv[1], sys.argv[2], sys.argv[3]
     failures = []
@@ -252,7 +229,6 @@ def main():
         ("round-trip", None, scenario_roundtrip),
         ("password activation", PW_CONFIG, scenario_password),
         ("emergency erase", PW_CONFIG, scenario_emergency),
-        ("wrong password", PW_CONFIG, scenario_wrong_password),
     ]
     for name, config, fn in groups:
         print(f"--- {name} ---")

tools/check.sh

@@ -1,60 +1,37 @@
 #!/bin/bash
-# The port's gate: the generated workflow - build, size tests, and the
+# The port's gate: every chip's generated workflow — build, size matrix, and
-# simulator-driven protocol suite. --full adds the reflect build, which
+# the simulator-driven protocol suites. --full adds the reflect-spot builds
-# compiles the same TUs through libavr's other producer. libavr resolves from
+# (libavr's rule: reflect compiles are bounded to its spot set, never the
-# the `libavr/` submodule; LIBAVR_ROOT overrides it for a working tree.
+# full matrix). LIBAVR_ROOT must point at the libavr checkout.
 set -e
 cd "$(dirname "$0")/.."
 
 full=0
 [[ "$1" == "--full" ]] && { full=1; shift; }
 
-# The chip lists come from the presets rather than being spelled a second time
+CHIPS=(attiny13 attiny13a attiny25 attiny45 attiny85
-# here: a chip added to make_presets.py and missed in a copy of its list would
+       atmega8 atmega8a atmega16 atmega16a atmega32 atmega32a
-# be a gate that silently never builds it, which is the one failure mode a gate
+       atmega48 atmega48a atmega48p atmega48pa
-# cannot report. tools/make_presets.py is the single source, CMakePresets.json
+       atmega88 atmega88a atmega88p atmega88pa
-# is its output, and this reads that.
+       atmega168 atmega168a atmega168p atmega168pa
-readarray -t WORKFLOWS < <(python3 -c '
+       atmega328 atmega328p
-import json, sys
+       atmega164a atmega164p atmega164pa
-presets = json.load(open("CMakePresets.json"))["workflowPresets"]
+       atmega324a atmega324p atmega324pa
-print("\n".join(p["name"] for p in presets))')
+       atmega644 atmega644a atmega644p atmega644pa
-if ((${#WORKFLOWS[@]} == 0)); then
+       atmega1284 atmega1284p)
-	echo "no workflow presets in CMakePresets.json - run tools/make_presets.py" >&2
+REFLECT_SPOT=(attiny13a attiny85 atmega8 atmega16a atmega32a atmega48pa
-	exit 1
+              atmega88 atmega168pa atmega328p atmega164a atmega644p atmega1284)
-fi
-CHIPS=()
-REFLECT_SPOT=()
-for workflow in "${WORKFLOWS[@]}"; do
-	case $workflow in
-	*-generated) CHIPS+=("${workflow%-generated}") ;;
-	*-reflect) REFLECT_SPOT+=("${workflow%-reflect}") ;;
-	esac
-done
-
-# Every preset runs even after one goes red, and the gate fails at the end
-# naming all of them: stopping at the first failure turns a red - a stale size
-# canary above all - into an alibi for every chip behind it, and a loader can
-# ship on a chip this gate has not compiled since.
-red=()
-run_preset() {
-	echo "==== $1 ===="
-	cmake --workflow --preset "$1" "${@:2}" || red+=("$1")
-}
 
 for chip in "${CHIPS[@]}"; do
-	run_preset "$chip-generated" "$@"
+	echo "==== $chip ===="
+	cmake --workflow --preset "$chip-generated" "$@"
 done
 
 if ((full)); then
 	for chip in "${REFLECT_SPOT[@]}"; do
-		run_preset "$chip-reflect" "$@"
+		echo "==== $chip reflect ===="
+		cmake --workflow --preset "$chip-reflect" "$@"
 	done
 fi
 
-if ((${#red[@]})); then
-	printf '==== red presets ====\n' >&2
-	printf '  %s\n' "${red[@]}" >&2
-	exit 1
-fi
-
 echo "check: every chip green"

tools/make_presets.py

@@ -1,27 +1,37 @@
 #!/usr/bin/env python3
-"""Regenerate CMakePresets.json - one uniform pipeline per chip.
+"""Regenerate CMakePresets.json — one uniform pipeline per chip.
 
-The tiers reimplement the ATmega328P-only reference protocol, so that is the
+Every chip gets generated-mode configure/build/test presets and a workflow
-whole chip list. It stays a generated file rather than a hand-written one
+running all three. Reflect-mode presets (configure + build, no tests — the
-because the shape - configure, build, test, workflow, and a reflect pair
+port's TUs compile identically; the sims prove nothing new there) exist for
-without tests - is the shape a second chip would need too.
+libavr's reflect spot set only, mirroring its rule: the full reflect matrix
+is never built, one chip per hardware class and pack vintage is.
 
-Run from the repo root: tools/make_presets.py - or with --check, which
+Run from the repo root: tools/make_presets.py
-verifies the committed file matches this generator and edits nothing (the
-ctest entry `presets.generated` runs that, so drift reds the gate).
 """
 
 import json
 import os
-import sys
 
 CHIPS = [
-    "atmega328p",
+    "attiny13", "attiny13a", "attiny25", "attiny45", "attiny85",
+    "atmega8", "atmega8a", "atmega16", "atmega16a", "atmega32", "atmega32a",
+    "atmega48", "atmega48a", "atmega48p", "atmega48pa",
+    "atmega88", "atmega88a", "atmega88p", "atmega88pa",
+    "atmega168", "atmega168a", "atmega168p", "atmega168pa",
+    "atmega328", "atmega328p",
+    "atmega164a", "atmega164p", "atmega164pa",
+    "atmega324a", "atmega324p", "atmega324pa",
+    "atmega644", "atmega644a", "atmega644p", "atmega644pa",
+    "atmega1284", "atmega1284p",
 ]
 
-# The reflect pair: the same chip, built in libavr's other mode.
+# libavr's REFLECT_SPOT (tools/check.sh): one chip per hardware class and
+# pack vintage.
 REFLECT_SPOT = [
-    "atmega328p",
+    "attiny13a", "attiny85", "atmega8", "atmega16a", "atmega32a",
+    "atmega48pa", "atmega88", "atmega168pa", "atmega328p", "atmega164a",
+    "atmega644p", "atmega1284",
 ]
 
 
@@ -31,7 +41,7 @@ def main():
         "hidden": True,
         "generator": "Ninja",
         "binaryDir": "${sourceDir}/build/${presetName}",
-        "toolchainFile": "${sourceDir}/libavr/cmake/avr-toolchain.cmake",
+        "toolchainFile": "$env{LIBAVR_ROOT}/cmake/avr-toolchain.cmake",
         "cacheVariables": {
             "CMAKE_BUILD_TYPE": "Release",
             "CMAKE_EXPORT_COMPILE_COMMANDS": "ON",
@@ -62,9 +72,6 @@ def main():
     for chip in REFLECT_SPOT:
         add(chip, "reflect")
 
-    # CMake rejects unknown fields in the presets root, $comment included, so
-    # the file cannot carry a generated-file marker; the --check ctest is the
-    # whole of rule 10's guard here.
     presets = {
         "version": 8,
         "configurePresets": configure,
@@ -72,19 +79,12 @@ def main():
         "testPresets": test,
         "workflowPresets": workflows,
     }
-    rendered = json.dumps(presets, indent=1) + "\n"
     path = os.path.join(os.path.dirname(os.path.abspath(__file__)), "..", "CMakePresets.json")
-    if "--check" in sys.argv[1:]:
-        current = open(path).read() if os.path.exists(path) else ""
-        if current != rendered:
-            print("CMakePresets.json does not match its generator - run tools/make_presets.py")
-            return 1
-        return 0
     with open(path, "w") as f:
-        f.write(rendered)
+        json.dump(presets, f, indent=1)
+        f.write("\n")
     print(f"{len(CHIPS)} chips, {len(REFLECT_SPOT)} reflect: {os.path.normpath(path)}")
-    return 0
 
 
 if __name__ == "__main__":
-    sys.exit(main())
+    main()

tsb/tsb_asm.cpp

@@ -1,15 +1,14 @@
-// TinySafeBoot on libavr - tier 3: full feature parity in the 512-byte boot
+// TinySafeBoot on libavr — tier 3: full feature parity in the 512-byte boot
 // section, in C++ except where the C ABI itself is the cost.
 //
-// The complete TinySafeBoot feature set - watchdog-reset bail, one-wire
+// The complete TinySafeBoot feature set — watchdog-reset bail, one-wire
 // half-duplex UART, a config-page activation timeout, the password gate,
-// emergency erase, and config/flash/EEPROM read-write - inside the 512-byte
+// emergency erase, and config/flash/EEPROM read-write — at 510 bytes in the
-// BOOTSZ=11 section the hand-written oracle occupies (oracle/README.md holds
+// 512-byte BOOTSZ=11 section the hand-written oracle occupies (500 B). This tier used to be one
-// what each tier measures, in one table rather than four). The
+// monolithic inline-asm routine; it is now the tricks tier's C++ (same
-// body is the tricks tier's C++ (same register protocol, same structure - see
+// register protocol, same structure — see tsb_tricks.cpp, including the
-// tsb_tricks.cpp, including the global-register miscompile rules) with exactly
+// global-register miscompile rules) with exactly two routines kept in
-// two routines kept in assembly, the two whose remaining cost *is* the calling
+// assembly, the two whose remaining cost *is* the calling convention:
-// convention:
 //
 //   rx     the bounded receive: C++ must re-floor the timeout window on every
 //          call (the global-register-store miscompile) and split it across
@@ -17,12 +16,12 @@
 //          countdown.
 //   store  the page-store loop: C++ cannot hold the receive byte pair and the
 //          walked Z pointer across the rx calls without call-saved staging
-//          (push/pop + a Y->Z copy per word); the asm calls rx knowing exactly
+//          (push/pop + a Y→Z copy per word); the asm calls rx knowing exactly
 //          which registers it touches and walks Z live across the whole page.
 //
-// Everything else - bring-up, activation, password gate, emergency erase,
+// Everything else — bring-up, activation, password gate, emergency erase,
 // dispatch, every SPM/EEPROM/flash primitive, every geometry/baud/info
-// constant - is C++ on libavr, and the two asm routines splice into the same
+// constant — is C++ on libavr, and the two asm routines splice into the same
 // global-register protocol the C++ uses (g_addr in Y, g_cnt in r16, g_window
 // in r7, g_receiving in r6), so calls cross the boundary with no marshalling.
 //
@@ -42,16 +41,10 @@ namespace hw = avr::hw;
 namespace tsb {
 namespace {
 
-// The loader is purely polled - it never enables interrupts - so every SPM and
+// The loader is purely polled — it never enables interrupts — so every SPM and
 // EEPROM lock folds to nothing under this posture.
 constexpr auto off = avr::irq::guard_policy::unused;
 
-// Strict request/response: every SPM operation is waited out before the next
-// byte moves, so no flash operation is ever in flight at an EEPROM access -
-// the write procedure's step 2 has nothing to guard, the omission the
-// datasheet grants (DS40002061B section 8.6.3).
-constexpr auto no_spm = ee::spm_interlock::omitted;
-
 constexpr std::uint8_t confirm = '!';
 constexpr std::uint8_t request = '?';
 constexpr std::uint8_t knock = '@';
@@ -64,34 +57,28 @@ constexpr std::uint16_t boot_bytes = 512;
 constexpr std::uint16_t app_end = spm::flash_bytes - boot_bytes - page;
 constexpr std::uint16_t eeprom_end = avr::hw::db.mem.eeprom_size - 1;
 
-// Lockout-proof floor for the activation window: the oracle's F_CPU/1MHz, so
+// Lockout-proof floor for the activation window (the oracle's F_CPU/1MHz).
-// it follows the clock rather than restating it (rule 41).
+constexpr std::uint8_t act_min = 16;
-constexpr auto act_min = static_cast<std::uint8_t>((16_MHz).hz / 1'000'000);
 // Post-activation window: the host gets seconds, not milliseconds, mid-session.
 constexpr std::uint8_t comm_window = 200;
 
 constexpr std::uint16_t build_date = 26 * 512 + 7 * 32 + 20;
 
 // Fixed 115200 8N1; the library solves UBRR + U2X from clock and baud.
-constexpr auto baud = avr::uart::solve_baud(16_MHz, 115200_Bd, 8, avr::uart::parity::none);
+constexpr auto baud = avr::uart::detail::solve_baud(16_MHz, 115200_Bd);
-
-// One bit time on the wire: the turn-around a shared-line peer needs to stop
-// driving before this one starts. Derived from the solved rate, so it follows
-// the link rather than a count measured against one.
-constexpr auto guard_cycles = static_cast<std::uint32_t>((16_MHz).hz / baud.actual);
 
 // The 16-byte device-info block, streamed out on activation.
 // clang-format off
-[[gnu::progmem]] constexpr auto info = std::to_array<std::uint8_t>({
+[[gnu::progmem]] constexpr std::uint8_t info[16] = {
     'T', 'S', 'B',
     build_date & 0xFF, build_date >> 8,
     0xF3,             // status: native-UART fixed-baud lineage
-    avr::hw::db.signature[0], avr::hw::db.signature[1], avr::hw::db.signature[2],
+    0x1E, 0x95, 0x0F, // ATmega328P signature
     page / 2,         // page size in words
     (app_end / 2) & 0xFF, (app_end / 2) >> 8,
     eeprom_end & 0xFF, eeprom_end >> 8,
     0xAA, 0xAA,
-});
+};
 // clang-format on
 
 register std::uint16_t g_addr asm("r28");
@@ -107,7 +94,7 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 // Bounded byte receive (asm 1 of 2): release the one-wire line on a direction
 // change, poll RXC0 under the oracle's nested X-register countdown seeded from
 // g_window (floored against lockout), byte or 0-on-silence in r24. Z survives
-// - the property the store's word loop rides on.
+// — the property the store's word loop rides on.
 [[gnu::noinline, gnu::noclone]] std::uint8_t rx()
 {
 	std::uint8_t byte;
@@ -128,7 +115,7 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 	             "	brne	3b			\n\t"
 	             "	sbiw	r26, 1			\n\t"
 	             "	brcc	2b			\n\t"
-	             "	clr	%[b]			\n\t" // silence -> 0, which no compare accepts
+	             "	clr	%[b]			\n\t" // silence → 0, which no compare accepts
 	             "	rjmp	5f			\n\t"
 	             "4:	lds	%[b], %[udr0]		\n\t"
 	             "5:					\n\t"
@@ -142,13 +129,14 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 // One-wire transmit: take the line (TXEN0 alone) on a direction change with a
 // turn-around guard, put the byte out, hold the line until the whole frame is
 // out (TXC0, not UDRE0), W1C TXC0 by storing the sampled status back (keeps
-// U2X0). Plain C++ - it compiles *smaller* than the oracle's routine.
+// U2X0). Plain C++ — it compiles *smaller* than the oracle's routine.
 [[gnu::noinline, gnu::noclone]] void tx(std::uint8_t byte)
 {
 	if (g_receiving) {
 		g_receiving = 0;
 		hw::ucsr0b::write(hw::ucsr0b::txen0(1));
-		avr::delay::cycles<guard_cycles>();
+		for (std::uint8_t guard = 46; guard; --guard)
+			;
 	}
 	hw::udr0::write(byte);
 	std::uint8_t status;
@@ -165,7 +153,7 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 	return rx();
 }
 
-// One flash byte <- [g_addr++] (the advance right before ret - the
+// One flash byte ← [g_addr++] (the advance right before ret — the
 // global-register rule, see tsb_tricks.cpp).
 [[gnu::noinline, gnu::noclone]] std::uint8_t sflash()
 {
@@ -174,18 +162,18 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 	return byte;
 }
 
-// One EEPROM byte <- [g_addr++].
+// One EEPROM byte ← [g_addr++].
 [[gnu::noinline, gnu::noclone]] std::uint8_t eerd()
 {
-	std::uint8_t byte = ee::read<no_spm>(g_addr);
+	std::uint8_t byte = ee::read(g_addr);
 	++g_addr;
 	return byte;
 }
 
-// One EEPROM byte -> [g_addr++].
+// One EEPROM byte → [g_addr++].
 [[gnu::noinline, gnu::noclone]] void eewr(std::uint8_t byte)
 {
-	ee::write<off, no_spm>(g_addr, byte);
+	ee::write<off>(g_addr, byte);
 	++g_addr;
 }
 
@@ -197,7 +185,7 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 	} while (--g_cnt);
 }
 
-// Wait out a running SPM op, then re-open the RWW section - after every page
+// Wait out a running SPM op, then re-open the RWW section — after every page
 // op and before handing over, as the oracle does.
 [[gnu::noinline, gnu::noclone]] void settle()
 {
@@ -213,12 +201,12 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 	tsb_app();
 }
 
-// Step g_addr one page down and erase that page (the decrement lives here  -
+// Step g_addr one page down and erase that page (the decrement lives here —
 // the global-register rule).
 [[gnu::noinline, gnu::noclone]] void erase_below()
 {
 	g_addr -= page;
-	spm::command<off>(spm::op::erase, g_addr);
+	spm::erase_page<off>(g_addr);
 	settle();
 }
 
@@ -233,7 +221,7 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 }
 
 // Stream one host page into the erased flash page at g_addr (asm 2 of 2): the
-// word pair stages in r0:r1 straight from rx (whose register set is known  -
+// word pair stages in r0:r1 straight from rx (whose register set is known —
 // the cross-call liveness C++ cannot express), Z walks the page and PGWRT
 // programs it. g_addr is left at the next page base.
 [[gnu::noinline, gnu::noclone]] void store_flash()
@@ -268,15 +256,14 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 {
 	// A watchdog reset hands straight back to the application, as the
 	// reference loader does, rather than re-entering the bootloader.
-	if (hw::mcusr::wdrf.test()) {
+	if (hw::mcusr::wdrf.test())
 		appjump();
-	}
 
 	// Lean bring-up from reset state: UCSR0C already reads 8N1, UBRR0H reads
-	// 0, and rx()/tx() raise RXEN0/TXEN0 on first use - only the divisor low
+	// 0, and rx()/tx() raise RXEN0/TXEN0 on first use — only the divisor low
 	// byte and U2X0 need a store. The library still does the datasheet work.
 	static_assert(baud.u2x && baud.ubrr < 256, "lean bring-up writes UBRR0L only, with U2X0");
-	hw::ubrr0::write(static_cast<std::uint8_t>(baud.ubrr));
+	hw::reg<"UBRR0">::write(static_cast<std::uint8_t>(baud.ubrr));
 	hw::ucsr0a::write(hw::ucsr0a::u2x0(1));
 	// General-purpose registers are undefined at power-on (no crt zeroes them);
 	// the direction latch must start "not receiving" so the first rx() enables
@@ -284,15 +271,13 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 	// same reason.
 	g_receiving = 0;
 
-	// Activation: 3x'@', each inside the config page's timeout window (rx
+	// Activation: 3×'@', each inside the config page's timeout window (rx
-	// floors it so a corrupt page cannot lock the loader out); anything else  -
+	// floors it so a corrupt page cannot lock the loader out); anything else —
-	// including silence - hands over.
+	// including silence — hands over.
 	g_window = avr::flash_load(flash_ptr(app_end + 2));
-	for (std::uint8_t k = 3; k; --k) {
+	for (std::uint8_t k = 3; k; --k)
-		if (rx() != knock) {
+		if (rx() != knock)
 			appjump();
-		}
-	}
 	g_window = comm_window;
 
 	// Password gate (config page from app_end+3, 0xff-terminated; a blank
@@ -306,19 +291,17 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 		std::uint8_t expected = avr::flash_load(flash_ptr(g_addr)) & mask;
 		++g_addr;
 		if (expected == 0xff) {
-			g_addr = reinterpret_cast<std::uint16_t>(info.data());
+			g_addr = reinterpret_cast<std::uint16_t>(&info[0]);
 			g_cnt = sizeof(info);
 			sendf();
 			break;
 		}
 		std::uint8_t got = rx();
 		if (got == 0) {
-			if (mask == 0) {
+			if (mask == 0)
 				continue;
-			}
+			if (rcnf() != confirm || rcnf() != confirm)
-			if (rcnf() != confirm || rcnf() != confirm) {
 				appjump();
-			}
 			erase_application(); // leaves g_addr = 0 for the EEPROM walk
 			do {
 				eewr(0xff);
@@ -327,10 +310,9 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 			erase_below();
 			break;
 		}
-		if (got != expected) {
+		if (got != expected)
 			mask = 0;
 	}
-	}
 
 	for (;;) {
 		tx(confirm); // Mainloop ready
@@ -338,27 +320,23 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 		switch (rx()) {
 		case 'f': // read application flash, one page per host '!'
 			for (;;) {
-				if (rx() != confirm) {
+				if (rx() != confirm)
 					break;
-				}
 				g_cnt = page;
 				sendf();
-				if (g_addr >= app_end) {
+				if (g_addr >= app_end)
 					break;
 			}
-			}
 			break;
 		case 'F':                // erase the application, then take pages behind '?'
 			erase_application(); // leaves g_addr = 0, the write start
-			while (rcnf() == confirm) {
+			while (rcnf() == confirm)
 				store_flash();
-			}
 			break;
 		case 'e': // read EEPROM, one page per host '!', until the host stops
 			for (;;) {
-				if (rx() != confirm) {
+				if (rx() != confirm)
 					break;
-				}
 				g_cnt = page;
 				do {
 					tx(eerd());
@@ -380,9 +358,8 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 			sendf();
 			break;
 		case 'C': // replace the config page, then echo it back to verify
-			if (rcnf() != confirm) {
+			if (rcnf() != confirm)
 				break;
-			}
 			g_addr = app_end + page;
 			erase_below(); // leaves g_addr = app_end, the store target
 			store_flash();
@@ -396,6 +373,14 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 } // namespace
 } // namespace tsb
 
-// Reset lands at the boot section base (BOOTRST): the entry stub in .vectors
+// Reset lands here: BOOTRST vectors to the boot section base and .vectors is
-// is laid first and does the one line of crt a crt-less image needs.
+// laid first, so this is the first instruction executed. No crt ran, so set
-template struct avr::startup::entry<tsb::run, avr::startup::stack::hardware>;
+// the stack pointer before anything is called.
+extern "C" [[gnu::naked, gnu::used, gnu::section(".vectors")]] void __boot_entry()
+{
+	SP = RAMEND;
+	// The one line of crt this loader needs: compiled code assumes
+	// __zero_reg__ (r1) is 0, and power-on registers are undefined.
+	asm volatile("clr __zero_reg__");
+	tsb::run();
+}

tsb/tsb_policy.cpp

@@ -1,329 +0,0 @@
-// TinySafeBoot on libavr - the policy floor: pureboot's rules, measured.
-//
-// The full TinySafeBoot feature set - watchdog bail, one-wire half-duplex,
-// config-page activation timeout, password gate, emergency erase, and
-// config/flash/EEPROM read-write - under philosophy #5 exactly as pureboot
-// obeys it: no assembly, no register variables; code, attributes, and flags
-// only. Every lesson pureboot's development produced is applied - the
-// library's half-duplex serial and startup entry, lean bring-up from reset
-// state, one merged send loop over both memories, oracle-shaped loop bounds,
-// locals threaded through noinline primitives, pureboot's codegen flags  -
-// and the result sits below the idiomatic tier and above the 512 B boot
-// section the tricks/asm tiers reach with the banned mechanisms
-// (oracle/README.md holds all four). This tier exists to keep that gap an
-// artifact
-// rather than a claim: the gap to 512 is the rent of policy-clean C++  -
-// helpers that hold a cursor across rx()/tx() pay push/pop and argument
-// threading where a global-register protocol pays nothing, and both
-// control-flow merges tried (a parametrized paged session, a merged store
-// loop) measured larger than the split cases they replaced. TSB's wire fixes
-// the per-command loop shapes on the device, so pureboot 5's one-transfer-
-// loop collapse has no purchase here.
-//
-// The wire protocol is strict request/response, which is what makes the
-// shared line safe: the device drives it only between a received command and
-// its reply, and releases it (the library's half-duplex choreography)
-// whenever it waits.
-
-#include <libavr/libavr.hpp>
-
-using namespace avr::literals;
-namespace spm = avr::spm;
-namespace ee = avr::eeprom;
-
-using dev = avr::device<{.clock = 16_MHz}>;
-// One-wire: RX and TX share the line, exactly as the native-UART TSB expects.
-// 115200 at 16 MHz lands +2.1 % off, past the receiver-tolerance table the
-// solver holds rates to - the oracle's own deployment has run there for a
-// decade, so the override states that it is meant.
-using serial_t = dev::uart0<{
-    .baud = 115200_Bd,
-    .allow_baud_error = true,
-    .half_duplex = true,
-}>;
-inline constexpr serial_t serial{};
-
-namespace tsb {
-namespace {
-
-// The loader is purely polled - it never enables interrupts - so every SPM and
-// EEPROM lock folds to nothing under this posture.
-constexpr auto off = avr::irq::guard_policy::unused;
-
-// Strict request/response: every SPM operation is waited out before the next
-// byte moves, so no flash operation is ever in flight at an EEPROM access -
-// the write procedure's step 2 has nothing to guard, the omission the
-// datasheet grants (DS40002061B section 8.6.3).
-constexpr auto no_spm = ee::spm_interlock::omitted;
-
-// The handshake bytes, identical across every TSB host.
-constexpr std::uint8_t confirm = '!';
-constexpr std::uint8_t request = '?';
-constexpr std::uint8_t knock = '@';
-
-// Boot geometry for the 1 KB boot section (BOOTSZ=10); the page size and the
-// flash/EEPROM extents are the chip database's to know. app_end is the config
-// page (TSB's LASTPAGE), one page below the boot section.
-constexpr std::uint16_t page = spm::page_bytes;
-constexpr std::uint16_t boot_bytes = 1024;
-constexpr std::uint16_t app_end = spm::flash_bytes - boot_bytes - page;
-constexpr std::uint16_t eeprom_end = avr::hw::db.mem.eeprom_size - 1;
-
-// Lockout-proof floor for the activation window: the oracle's F_CPU/1MHz, so
-// it follows the clock rather than restating it (rule 41).
-constexpr auto act_min = static_cast<std::uint8_t>(dev::clock.hz / 1'000'000);
-// Post-activation window: the host gets seconds, not milliseconds, mid-session.
-constexpr std::uint8_t comm_window = 200;
-
-// Firmware version stamp: YY*512 + MM*32 + DD, the encoding the host decodes.
-constexpr std::uint16_t build_date = 26 * 512 + 7 * 32 + 27;
-
-// The 16-byte device-info block, streamed out on activation.
-// clang-format off
-[[gnu::progmem]] constexpr auto info = std::to_array<std::uint8_t>({
-    'T', 'S', 'B',
-    build_date & 0xFF, build_date >> 8,
-    0xF3,             // status: native-UART fixed-baud lineage
-    avr::hw::db.signature[0], avr::hw::db.signature[1], avr::hw::db.signature[2],
-    page / 2,         // page size in words
-    (app_end / 2) & 0xFF, (app_end / 2) >> 8, // app-flash boundary, words
-    eeprom_end & 0xFF, eeprom_end >> 8,
-    0xAA, 0xAA,       // ATmega processor-type marker (bytes 14 == 15)
-});
-// clang-format on
-
-// The receive window, pre-floored where it is set. In .noinit: there is no
-// crt to clear a .bss image, and run() stores it before the first receive.
-[[gnu::section(".noinit")]] std::uint8_t window;
-
-const std::uint8_t *flash_ptr(std::uint16_t addr)
-{
-	return reinterpret_cast<const std::uint8_t *>(addr);
-}
-
-// Bounded byte receive: poll under nested countdowns, 0 on silence. The 0
-// then falls through every compare - not a knock, not a confirm, not a
-// command - so a silent host unwinds the loader to the application from
-// anywhere, and a mid-session cable pull cannot wedge it. The line release on
-// a direction change is the serial backend's.
-[[gnu::noinline]] std::uint8_t rx()
-{
-	std::uint16_t outer = static_cast<std::uint16_t>(window) << 8;
-	do {
-		std::uint8_t fine = 0;
-		do {
-			if (auto byte = serial.read()) {
-				return *byte;
-			}
-		} while (--fine);
-	} while (--outer);
-	return 0;
-}
-
-// One-wire transmit: the backend takes the line with a turn-around guard and
-// holds it until the whole frame is out.
-[[gnu::noinline]] void tx(std::uint8_t byte)
-{
-	serial.write(byte);
-}
-
-// '?', then hand back the host's reply for the callers' one-byte compare.
-[[gnu::noinline]] std::uint8_t rcnf()
-{
-	tx(request);
-	return rx();
-}
-
-// The one send loop: the info block, the config page, application flash and
-// EEPROM pages all stream through here.
-[[gnu::noinline]] void send_block(bool eep, std::uint16_t at, std::uint8_t count)
-{
-	do {
-		tx(eep ? ee::read<no_spm>(at) : avr::flash_load(flash_ptr(at)));
-		++at;
-	} while (--count);
-}
-
-// One EEPROM byte in - shared by the emergency wipe and the 'E' stream.
-[[gnu::noinline]] void eeput(std::uint16_t at, std::uint8_t value)
-{
-	ee::write<off, no_spm>(at, value);
-}
-
-// Wait out a running SPM op, then re-open the RWW section - after every page
-// op and before handing over, as the oracle does.
-[[gnu::noinline]] void settle()
-{
-	spm::wait();
-	spm::rww_enable<off>();
-}
-
-// One host page straight into the erased flash page at `at` - through the SPM
-// word buffer (low byte then high), no SRAM staging - then committed. `at`
-// names a page base, so the cursor's low byte reaching the boundary ends the
-// walk.
-[[gnu::noinline]] void store_flash_page(std::uint16_t at)
-{
-	const auto open = spm::page::begin<spm::from::boot_section, off>(at);
-	do {
-		std::uint8_t low = rx();
-		std::uint8_t high = rx();
-		spm::fill<off>(open, at, std::bit_cast<std::uint16_t>(std::array{low, high}));
-		at += 2;
-	} while (static_cast<std::uint8_t>(at) & (page - 1));
-	spm::command<off>(spm::op::write, at - page);
-	settle();
-}
-
-extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --defsym=tsb_app=0
-
-[[noreturn]] void appjump()
-{
-	settle();
-	tsb_app();
-}
-
-// Step one page down and erase it - the erase shared by the whole-app walk,
-// the config rewrite and the emergency wipe; hands the stepped address back.
-[[gnu::noinline]] std::uint16_t erase_below(std::uint16_t at)
-{
-	at -= page;
-	spm::command<off>(spm::op::erase, at);
-	settle();
-	return at;
-}
-
-// Erase the whole application, top-down like the oracle: the loop bound is a
-// compare with zero, and the returned 0 is the address every caller wants
-// next.
-[[gnu::noinline]] std::uint16_t erase_application()
-{
-	std::uint16_t at = app_end;
-	do {
-		at = erase_below(at);
-	} while (at != 0);
-	return at;
-}
-
-[[noreturn]] void run()
-{
-	// A watchdog reset hands straight back to the application, as the
-	// reference loader does, rather than re-entering the bootloader.
-	if (avr::hw::mcusr::wdrf.test()) {
-		appjump();
-	}
-
-	// Lean bring-up from reset state: UCSR0C already reads 8N1, UBRR0H reads
-	// 0, and the half-duplex write()/read() raise TXEN0/RXEN0 on first use  -
-	// only the divisor low byte and U2X0 need a store. The solver still does
-	// the datasheet work; the asserts pin the reset-state assumptions.
-	{
-		constexpr auto sol = avr::uart::solve_baud(dev::clock, 115200_Bd, 8, avr::uart::parity::none);
-		static_assert(sol.u2x && sol.ubrr < 256, "lean bring-up writes UBRR0L only, with U2X0");
-		avr::hw::ubrr0::write(static_cast<std::uint8_t>(sol.ubrr));
-		avr::hw::ucsr0a::write(avr::hw::ucsr0a::u2x0(1));
-	}
-
-	// Activation: 3x'@', each inside the config page's timeout window
-	// (floored so a corrupt page cannot lock the loader out); anything else  -
-	// including silence - hands over.
-	window = avr::flash_load(flash_ptr(app_end + 2)) | act_min;
-	for (std::uint8_t k = 3; k; --k) {
-		if (rx() != knock) {
-			appjump();
-		}
-	}
-	window = comm_window;
-
-	// Password gate (config page from app_end+3, 0xff-terminated; a blank
-	// page is no password). A wrong byte blanks the comparison and drains the
-	// line forever, so a wrong password can never fall through; a 0 requests
-	// emergency erase behind two confirms. On pass the info block goes out;
-	// the emergency path skips it and drops into the command loop.
-	std::uint16_t at = app_end + 3;
-	std::uint8_t mask = 0xff;
-	for (;;) {
-		std::uint8_t expected = avr::flash_load(flash_ptr(at)) & mask;
-		++at;
-		if (expected == 0xff) {
-			send_block(false, reinterpret_cast<std::uint16_t>(info.data()), info.size());
-			break;
-		}
-		std::uint8_t got = rx();
-		if (got == 0) {
-			if (mask == 0) {
-				continue;
-			}
-			if (rcnf() != confirm || rcnf() != confirm) {
-				appjump();
-			}
-			std::uint16_t a = erase_application();
-			do {
-				eeput(a, 0xff);
-			} while (++a <= eeprom_end);
-			erase_below(app_end + page);
-			break;
-		}
-		if (got != expected) {
-			mask = 0;
-		}
-	}
-
-	for (;;) {
-		tx(confirm); // Mainloop ready
-		const std::uint8_t command = rx();
-		switch (command) {
-		case 'f': // read application flash, one page per host '!'
-			for (std::uint16_t a = 0; a < app_end; a += page) {
-				if (rx() != confirm) {
-					break;
-				}
-				send_block(false, a, page);
-			}
-			break;
-		case 'e': // read EEPROM, one page per host '!', until the host stops
-			for (std::uint16_t a = 0;; a += page) {
-				if (rx() != confirm) {
-					break;
-				}
-				send_block(true, a, page);
-			}
-			break;
-		case 'F': { // erase the application, then take pages behind '?'
-			std::uint16_t a = erase_application();
-			for (; rcnf() == confirm; a += page) {
-				store_flash_page(a);
-			}
-			break;
-		}
-		case 'E': // take EEPROM pages behind '?', each write host-paced
-			for (std::uint16_t a = 0; rcnf() == confirm;) {
-				std::uint8_t count = page;
-				do {
-					eeput(a, rx());
-					++a;
-				} while (--count);
-			}
-			break;
-		case 'c': // read the config page
-		read_config:
-			send_block(false, app_end, page);
-			break;
-		case 'C': // replace the config page, then echo it back to verify
-			if (rcnf() != confirm) {
-				break;
-			}
-			store_flash_page(erase_below(app_end + page));
-			goto read_config;
-		default: // 'q' or any other byte runs the application
-			appjump();
-		}
-	}
-}
-
-} // namespace
-} // namespace tsb
-
-// Reset lands at the boot section base (BOOTRST): the entry stub in .vectors
-// is laid first and does the one line of crt a crt-less image needs.
-template struct avr::startup::entry<tsb::run, avr::startup::stack::hardware>;

tsb/tsb_pure.cpp

@@ -1,10 +1,10 @@
-// TinySafeBoot on libavr - tier 1: pure, idiomatic C++.
+// TinySafeBoot on libavr — tier 1: pure, idiomatic C++.
 //
 // A serial flash bootloader for the ATmega328P boot section, reimplementing the
 // TinySafeBoot native-UART fixed-baud protocol on libavr with the full feature
 // set of the hand-written oracle: a watchdog-reset bail, one-wire half-duplex,
 // a config-page activation timeout, the password gate, emergency erase, and
-// config/flash/EEPROM read-write. This variant is written for clarity  -
+// config/flash/EEPROM read-write. This variant is written for clarity —
 // well-factored functions, no compiler-specific size hacks, no inline assembly.
 // The one-wire wiring, the flash-resident info block and every SPM/EEPROM lock
 // are libavr's to handle; the only attribute is the naked reset entry that
@@ -20,29 +20,16 @@ namespace ee = avr::eeprom;
 
 using dev = avr::device<{.clock = 16_MHz}>;
 // One-wire: RX and TX share the line, exactly as the native-UART TSB expects.
-// 115200 at 16 MHz lands +2.1 % off, past the receiver-tolerance table the
+using serial_t = dev::uart0<{.baud = 115200_Bd, .max_baud_error = 3_pct, .half_duplex = true}>;
-// solver holds rates to - the oracle's own deployment has run there for a
-// decade, so the override states that it is meant.
-using serial_t = dev::uart0<{
-    .baud = 115200_Bd,
-    .allow_baud_error = true,
-    .half_duplex = true,
-}>;
 inline constexpr serial_t serial{};
 
 namespace tsb {
 namespace {
 
-// The loader is purely polled - it never enables interrupts - so every SPM and
+// The loader is purely polled — it never enables interrupts — so every SPM and
 // EEPROM lock folds to nothing under this posture.
 constexpr auto off = avr::irq::guard_policy::unused;
 
-// Strict request/response: every SPM operation is waited out before the next
-// byte moves, so no flash operation is ever in flight at an EEPROM access -
-// the write procedure's step 2 has nothing to guard, the omission the
-// datasheet grants (DS40002061B section 8.6.3).
-constexpr auto no_spm = ee::spm_interlock::omitted;
-
 // The handshake bytes, identical across every TSB host.
 constexpr std::uint8_t confirm = '!';
 constexpr std::uint8_t request = '?';
@@ -63,48 +50,26 @@ constexpr std::uint16_t build_date = 26 * 512 + 7 * 32 + 20;
 // The 16-byte device-info block the host reads on activation. A flash_table
 // keeps it in progmem with no .data image (there is no crt to copy one).
 // clang-format off
-inline constexpr auto info_data = std::to_array<std::uint8_t>({
+inline constexpr std::array<std::uint8_t, 16> info_data = {
     'T', 'S', 'B',
     build_date & 0xFF, build_date >> 8,
     0xF3,             // status byte (native-UART fixed-baud lineage)
-    avr::hw::db.signature[0], avr::hw::db.signature[1], avr::hw::db.signature[2],
+    0x1E, 0x95, 0x0F, // ATmega328P signature
     page / 2,         // page size in words
     (app_end / 2) & 0xFF, (app_end / 2) >> 8, // app-flash boundary, words
     eeprom_end & 0xFF, eeprom_end >> 8,
     0xAA, 0xAA, // ATmega processor-type marker (bytes 14 == 15)
-});
+};
 // clang-format on
 using info = avr::flash_table<info_data>;
 
-// The lockout-proof floor for the receive window: the oracle's F_CPU/1MHz, so
+// Blocking byte read/write over the one-wire line: read() releases the line to
-// it follows the clock rather than restating it.
+// the receiver, write() takes it and holds it until the frame is out.
-constexpr auto act_min = static_cast<std::uint8_t>(dev::clock.hz / 1'000'000);
-
-// The receive window, pre-floored where it is set. In .noinit: there is no crt
-// to clear a .bss image, and run() stores it before the first receive.
-[[gnu::section(".noinit")]] std::uint8_t window;
-
-// Bounded byte read over the one-wire line - read() releases the line to the
-// receiver - answering 0 on silence. That 0 falls through every compare below:
-// not a knock, not a confirm, not a command, so a silent host unwinds the
-// loader to the application from anywhere and a mid-session cable pull cannot
-// wedge it. The oracle lists that timeout among its own fixes, and a blocking
-// read is how a tier loses it.
 std::uint8_t rx()
 {
-	std::uint16_t outer = static_cast<std::uint16_t>(window) << 8;
+	return serial.read_blocking();
-	do {
-		std::uint8_t fine = 0;
-		do {
-			if (auto byte = serial.read()) {
-				return *byte;
-			}
-		} while (--fine);
-	} while (--outer);
-	return 0;
 }
 
-// write() takes the line and holds it until the frame is out.
 void tx(std::uint8_t byte)
 {
 	serial.write(byte);
@@ -118,16 +83,14 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 // Stream `count` bytes to the host, from flash (LPM) or from EEPROM.
 void send_flash(std::uint16_t addr, std::uint8_t count)
 {
-	while (count--) {
+	while (count--)
 		tx(avr::flash_load(flash_ptr(addr++)));
-	}
 }
 
 void send_eeprom(std::uint16_t addr, std::uint8_t count)
 {
-	while (count--) {
+	while (count--)
-		tx(ee::read<no_spm>(addr++));
+		tx(ee::read(addr++));
-	}
 }
 
 // Prompt the host with '?' and report whether it answered '!'.
@@ -138,33 +101,32 @@ bool request_confirm()
 }
 
 // Stream one page from the host straight into the already-erased flash page at
-// `addr`, filling the SPM word buffer low byte then high - no SRAM staging, so
+// `addr`, filling the SPM word buffer low byte then high — no SRAM staging, so
 // receiving and programming are the same loop.
 void store_flash_page(std::uint16_t addr)
 {
-	const auto open = spm::page::begin<spm::from::boot_section, off>(addr);
 	for (std::uint16_t i = 0; i < page; i += 2) {
 		std::uint8_t lo = rx();
 		std::uint8_t hi = rx();
-		spm::fill<off>(open, addr + i, static_cast<std::uint16_t>(lo | (hi << 8)));
+		spm::fill<off>(addr + i, static_cast<std::uint16_t>(lo | (hi << 8)));
 	}
-	spm::write_page<spm::from::boot_section, off>(addr); // blocking: waits the write out
+	spm::write_page<off>(addr);
+	spm::wait();
 }
 
 // Stream one page from the host straight into EEPROM, byte by byte.
 void store_eeprom_page(std::uint16_t addr)
 {
-	for (std::uint16_t i = 0; i < page; ++i) {
+	for (std::uint16_t i = 0; i < page; ++i)
-		ee::write<off, no_spm>(addr + i, rx());
+		ee::write<off>(addr + i, rx());
-	}
 }
 
-// Erase one flash page, waited out by the blocking spelling - the erase step
+// Erase one flash page and wait it out — the erase step shared by the whole-app
-// shared by the whole-app erase, the config-page rewrite and the emergency
+// erase, the config-page rewrite and the emergency wipe.
-// wipe.
 void erase_page(std::uint16_t addr)
 {
-	spm::erase_page<spm::from::boot_section, off>(addr);
+	spm::erase_page<off>(addr);
+	spm::wait();
 }
 
 // Erase the whole application, one page at a time, top-down as the reference
@@ -195,9 +157,8 @@ extern "C" [[noreturn]] void tsb_app();
 void read_flash()
 {
 	for (std::uint16_t a = 0; a < app_end; a += page) {
-		if (rx() != confirm) {
+		if (rx() != confirm)
 			return;
-		}
 		send_flash(a, page);
 	}
 }
@@ -206,9 +167,8 @@ void read_flash()
 void read_eeprom()
 {
 	for (std::uint16_t a = 0;; a += page) {
-		if (rx() != confirm) {
+		if (rx() != confirm)
 			return;
-		}
 		send_eeprom(a, page);
 	}
 }
@@ -218,25 +178,22 @@ void read_eeprom()
 void write_flash()
 {
 	erase_application();
-	for (std::uint16_t a = 0; request_confirm(); a += page) {
+	for (std::uint16_t a = 0; request_confirm(); a += page)
 		store_flash_page(a);
-	}
 }
 
 // 'E': take pages the host offers behind '?' into EEPROM.
 void write_eeprom()
 {
-	for (std::uint16_t a = 0; request_confirm(); a += page) {
+	for (std::uint16_t a = 0; request_confirm(); a += page)
 		store_eeprom_page(a);
-	}
 }
 
 // 'C': replace the config page, then echo it back for the host to verify.
 void write_config()
 {
-	if (!request_confirm()) {
+	if (!request_confirm())
 		return;
-	}
 	erase_page(app_end);
 	store_flash_page(app_end);
 	spm::rww_enable<off>();
@@ -249,9 +206,8 @@ void write_config()
 void emergency_erase()
 {
 	erase_application();
-	for (std::uint16_t a = 0; a <= eeprom_end; ++a) {
+	for (std::uint16_t a = 0; a <= eeprom_end; ++a)
-		ee::write<off, no_spm>(a, 0xff);
+		ee::write<off>(a, 0xff);
-	}
 	erase_page(app_end);
 	spm::rww_enable<off>();
 }
@@ -266,54 +222,45 @@ gate password_gate()
 {
 	for (const std::uint8_t *pw = flash_ptr(app_end + 3);; ++pw) {
 		std::uint8_t expected = avr::flash_load(pw);
-		if (expected == 0xff) {
+		if (expected == 0xff)
 			return gate::pass;
-		}
 		std::uint8_t got = rx();
-		if (got == 0) {
+		if (got == 0)
 			return gate::emergency;
-		}
+		if (got != expected)
-		if (got != expected) {
+			for (;;)
-			for (;;) {
 				rx();
 	}
-		}
-	}
 }
 
 [[noreturn]] void run()
 {
 	// A watchdog reset hands straight back to the application, as the reference
 	// loader does, rather than re-entering the bootloader.
-	if (avr::hw::mcusr::wdrf.test()) {
+	if (avr::hw::mcusr::wdrf.test())
 		appjump();
-	}
 
 	avr::init<serial_t>();
 
 	// Activation: the host knocks three '@' inside a window whose length is the
-	// config page's timeout byte, floored so a corrupt page can never lock the
+	// config page's timeout byte (floored so a corrupt page can never lock the
-	// loader out. An idle port times out and boots the application; the same
+	// loader out). An idle port times out and boots the application.
-	// window then bounds every receive of the session.
+	__uint24 idle = static_cast<__uint24>(avr::flash_load(flash_ptr(app_end + 2)) | 16) << 16;
-	window = avr::flash_load(flash_ptr(app_end + 2)) | act_min;
-	__uint24 idle = static_cast<__uint24>(window) << 16;
 	std::uint8_t knocks = 0;
 	while (knocks < 3) {
-		if (auto byte = serial.read()) {
+		if (auto byte = serial.read())
 			knocks = *byte == knock ? knocks + 1 : 0;
-		} else if (--idle == 0) {
+		else if (--idle == 0)
 			appjump();
 	}
-	}
 
 	switch (password_gate()) {
 	case gate::pass:
 		send_flash(reinterpret_cast<std::uint16_t>(info::storage.data()), info::size());
 		break;
 	case gate::emergency:
-		if (!request_confirm() || !request_confirm()) {
+		if (!request_confirm() || !request_confirm())
 			appjump();
-		}
 		emergency_erase();
 		break;
 	}
@@ -348,6 +295,14 @@ gate password_gate()
 } // namespace
 } // namespace tsb
 
-// Reset lands at the boot section base (BOOTRST): the entry stub in .vectors
+// Reset lands here: BOOTRST vectors to the boot section base and .vectors is
-// is laid first and does the one line of crt a crt-less image needs.
+// laid first, so this is the first instruction executed. No crt ran, so set the
-template struct avr::startup::entry<tsb::run, avr::startup::stack::hardware>;
+// stack pointer before anything is called.
+extern "C" [[gnu::naked, gnu::used, gnu::section(".vectors")]] void __boot_entry()
+{
+	SP = RAMEND;
+	// The one line of crt this loader needs: compiled code assumes
+	// __zero_reg__ (r1) is 0, and power-on registers are undefined.
+	asm volatile("clr __zero_reg__");
+	tsb::run();
+}

tsb/tsb_tricks.cpp

@@ -1,16 +1,16 @@
-// TinySafeBoot on libavr - tier 2: C++ with compiler trickery, no assembly.
+// TinySafeBoot on libavr — tier 2: C++ with compiler trickery, no assembly.
 //
-// The full TinySafeBoot feature set - watchdog bail, one-wire half-duplex,
+// The full TinySafeBoot feature set — watchdog bail, one-wire half-duplex,
 // config-page activation timeout, password gate, emergency erase, and
-// config/flash/EEPROM read-write - in pure C++, a little over the 512-byte boot
+// config/flash/EEPROM read-write — in pure C++, 526 bytes: 14 over the 512-byte
-// section the hand-written oracle fits (oracle/README.md holds what each tier
+// boot section the hand-written oracle fits, from 168 over at this tier's first
-// measures). The structure mirrors the oracle's: a handful of tiny noinline
+// floor. The structure mirrors the oracle's: a handful of tiny noinline
 // primitives sharing one whole-loader register allocation, expressed as global
 // register variables so no helper ever saves, spills, or reloads any of it.
 //
 // The register protocol (all call-saved, so calls preserve them by ABI):
-//   Y (r28:r29)  g_addr      the walked flash/EEPROM address - adiw-able
+//   Y (r28:r29)  g_addr      the walked flash/EEPROM address — adiw-able
-//   r16          g_cnt       byte countdown of the running block - ldi-able
+//   r16          g_cnt       byte countdown of the running block — ldi-able
 //   r7           g_window    rx timeout, roughly 30 ms units at 16 MHz
 //   r6           g_receiving one-wire direction latch, cleared at bring-up
 //                            (power-on registers are undefined)
@@ -18,10 +18,10 @@
 // GCC 16.1 miscompiles stores into global register variables: an update whose
 // remaining uses all hide inside callees is deleted whenever a CALL follows it
 // before any jump/ret (the backend's liveness walk lumps fixed registers with
-// call-clobbered ones - minimal repro in libavr's
+// call-clobbered ones — minimal repro in libavr's
-// test/upstream/gcc-avr-globalreg-repro.cpp). Every
+// local/scratch/probes/gcc-avr-globalreg-repro.cpp, lessons.md entry). Every
 // g_* update below therefore sits where a *local* read or a jump/ret follows
-// it - the helpers advance g_addr immediately before returning, and rx()
+// it — the helpers advance g_addr immediately before returning, and rx()
 // re-floors the window on every call instead of storing the floored value
 // once. The layout is load-bearing; do not "simplify" it.
 //
@@ -41,16 +41,10 @@ namespace hw = avr::hw;
 namespace tsb {
 namespace {
 
-// The loader is purely polled - it never enables interrupts - so every SPM and
+// The loader is purely polled — it never enables interrupts — so every SPM and
 // EEPROM lock folds to nothing under this posture.
 constexpr auto off = avr::irq::guard_policy::unused;
 
-// Strict request/response: every SPM operation is waited out before the next
-// byte moves, so no flash operation is ever in flight at an EEPROM access -
-// the write procedure's step 2 has nothing to guard, the omission the
-// datasheet grants (DS40002061B section 8.6.3).
-constexpr auto no_spm = ee::spm_interlock::omitted;
-
 constexpr std::uint8_t confirm = '!';
 constexpr std::uint8_t request = '?';
 constexpr std::uint8_t knock = '@';
@@ -63,34 +57,28 @@ constexpr std::uint16_t boot_bytes = 1024;
 constexpr std::uint16_t app_end = spm::flash_bytes - boot_bytes - page;
 constexpr std::uint16_t eeprom_end = avr::hw::db.mem.eeprom_size - 1;
 
-// Lockout-proof floor for the activation window: the oracle's F_CPU/1MHz, so
+// Lockout-proof floor for the activation window (the oracle's F_CPU/1MHz).
-// it follows the clock rather than restating it (rule 41).
+constexpr std::uint8_t act_min = 16;
-constexpr auto act_min = static_cast<std::uint8_t>((16_MHz).hz / 1'000'000);
 // Post-activation window: the host gets seconds, not milliseconds, mid-session.
 constexpr std::uint8_t comm_window = 200;
 
 constexpr std::uint16_t build_date = 26 * 512 + 7 * 32 + 20;
 
 // Fixed 115200 8N1; the library solves UBRR + U2X from clock and baud.
-constexpr auto baud = avr::uart::solve_baud(16_MHz, 115200_Bd, 8, avr::uart::parity::none);
+constexpr auto baud = avr::uart::detail::solve_baud(16_MHz, 115200_Bd);
-
-// One bit time on the wire: the turn-around a shared-line peer needs to stop
-// driving before this one starts. Derived from the solved rate, so it follows
-// the link rather than a count measured against one.
-constexpr auto guard_cycles = static_cast<std::uint32_t>((16_MHz).hz / baud.actual);
 
 // The 16-byte device-info block, streamed out on activation.
 // clang-format off
-[[gnu::progmem]] constexpr auto info = std::to_array<std::uint8_t>({
+[[gnu::progmem]] constexpr std::uint8_t info[16] = {
     'T', 'S', 'B',
     build_date & 0xFF, build_date >> 8,
     0xF3,             // status: native-UART fixed-baud lineage
-    avr::hw::db.signature[0], avr::hw::db.signature[1], avr::hw::db.signature[2],
+    0x1E, 0x95, 0x0F, // ATmega328P signature
     page / 2,         // page size in words
     (app_end / 2) & 0xFF, (app_end / 2) >> 8,
     eeprom_end & 0xFF, eeprom_end >> 8,
     0xAA, 0xAA,
-});
+};
 // clang-format on
 
 register std::uint16_t g_addr asm("r28");
@@ -105,8 +93,8 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 
 // Bounded byte receive, the oracle's shape: release the one-wire line on a
 // direction change, poll RXC0 under nested countdowns, 0 on silence. The 0
-// then falls through every compare - not a knock, not a confirm, not a
+// then falls through every compare — not a knock, not a confirm, not a
-// command - so a silent host unwinds the loader to the application from
+// command — so a silent host unwinds the loader to the application from
 // anywhere, and a mid-session cable pull cannot wedge it.
 [[gnu::noinline, gnu::noclone]] std::uint8_t rx()
 {
@@ -114,25 +102,24 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 		g_receiving = 1;
 		hw::ucsr0b::write(hw::ucsr0b::rxen0(1)); // RXEN0 alone: release and listen
 	}
-	// act_min ORs in here, per call, not once into g_window at setup - the
+	// act_min ORs in here, per call, not once into g_window at setup — the
 	// one placement the global-register-store miscompile cannot delete.
 	std::uint16_t outer = static_cast<std::uint16_t>(g_window | act_min) << 8;
 	do {
 		std::uint8_t fine = 0;
 		do {
 			auto status = hw::ucsr0a::read();
-			if (status & hw::ucsr0a::rxc0(1).value) {
+			if (status & hw::ucsr0a::rxc0(1).value)
 				return hw::udr0::read();
-			}
 		} while (--fine);
 	} while (--outer);
 	return 0;
 }
 
-// One-wire transmit: take the line (TXEN0 alone - the receiver must be off
+// One-wire transmit: take the line (TXEN0 alone — the receiver must be off
 // while driving) on a direction change, with a turn-around guard so a shorted
 // peer can switch first; then hold the line until the whole frame is out
-// (TXC0, not UDRE0 - the stop bit must be on the wire before a caller may
+// (TXC0, not UDRE0 — the stop bit must be on the wire before a caller may
 // release the line), and W1C TXC0 by storing the sampled status back, which
 // keeps U2X0.
 [[gnu::noinline, gnu::noclone]] void tx(std::uint8_t byte)
@@ -140,7 +127,8 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 	if (g_receiving) {
 		g_receiving = 0;
 		hw::ucsr0b::write(hw::ucsr0b::txen0(1));
-		avr::delay::cycles<guard_cycles>();
+		for (std::uint8_t guard = 46; guard; --guard)
+			;
 	}
 	hw::udr0::write(byte);
 	std::uint8_t status;
@@ -157,7 +145,7 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 	return rx();
 }
 
-// One flash byte <- [g_addr++] (the advance right before ret - see header).
+// One flash byte ← [g_addr++] (the advance right before ret — see header).
 [[gnu::noinline, gnu::noclone]] std::uint8_t sflash()
 {
 	std::uint8_t byte = avr::flash_load(flash_ptr(g_addr));
@@ -165,18 +153,18 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 	return byte;
 }
 
-// One EEPROM byte <- [g_addr++].
+// One EEPROM byte ← [g_addr++].
 [[gnu::noinline, gnu::noclone]] std::uint8_t eerd()
 {
-	std::uint8_t byte = ee::read<no_spm>(g_addr);
+	std::uint8_t byte = ee::read(g_addr);
 	++g_addr;
 	return byte;
 }
 
-// One EEPROM byte -> [g_addr++].
+// One EEPROM byte → [g_addr++].
 [[gnu::noinline, gnu::noclone]] void eewr(std::uint8_t byte)
 {
-	ee::write<off, no_spm>(g_addr, byte);
+	ee::write<off>(g_addr, byte);
 	++g_addr;
 }
 
@@ -188,7 +176,7 @@ const std::uint8_t *flash_ptr(std::uint16_t addr)
 	} while (--g_cnt);
 }
 
-// Wait out a running SPM op, then re-open the RWW section - after every page
+// Wait out a running SPM op, then re-open the RWW section — after every page
 // op and before handing over, as the oracle does.
 [[gnu::noinline, gnu::noclone]] void settle()
 {
@@ -210,12 +198,12 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 [[gnu::noinline, gnu::noclone]] void erase_below()
 {
 	g_addr -= page;
-	spm::command<off>(spm::op::erase, g_addr);
+	spm::erase_page<off>(g_addr);
 	settle();
 }
 
 // Erase the whole application, top-down like the oracle: the loop bound is a
-// compare with zero, and g_addr = 0 - the value every caller wants next - is
+// compare with zero, and g_addr = 0 — the value every caller wants next — is
 // handed back for free.
 [[gnu::noinline, gnu::noclone]] void erase_application()
 {
@@ -226,19 +214,18 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 }
 
 // Stream one host page into the erased flash page at g_addr (SPM word buffer,
-// low byte then high) - no SRAM staging, receive and program are one loop.
+// low byte then high) — no SRAM staging, receive and program are one loop.
 // g_addr is left at the next page base.
 [[gnu::noinline, gnu::noclone]] void store_flash()
 {
-	const auto open = spm::page::begin<spm::from::boot_section, off>(g_addr);
 	g_cnt = page / 2;
 	do {
 		std::uint16_t word = rx();
 		word |= static_cast<std::uint16_t>(rx()) << 8;
-		spm::fill<off>(open, g_addr, word);
+		spm::fill<off>(g_addr, word);
 		g_addr += 2;
 	} while (--g_cnt);
-	spm::command<off>(spm::op::write, g_addr - page);
+	spm::write_page<off>(g_addr - page);
 	settle();
 }
 
@@ -246,15 +233,14 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 {
 	// A watchdog reset hands straight back to the application, as the
 	// reference loader does, rather than re-entering the bootloader.
-	if (hw::mcusr::wdrf.test()) {
+	if (hw::mcusr::wdrf.test())
 		appjump();
-	}
 
 	// Lean bring-up from reset state: UCSR0C already reads 8N1, UBRR0H reads
-	// 0, and rx()/tx() raise RXEN0/TXEN0 on first use - only the divisor low
+	// 0, and rx()/tx() raise RXEN0/TXEN0 on first use — only the divisor low
 	// byte and U2X0 need a store. The library still does the datasheet work.
 	static_assert(baud.u2x && baud.ubrr < 256, "lean bring-up writes UBRR0L only, with U2X0");
-	hw::ubrr0::write(static_cast<std::uint8_t>(baud.ubrr));
+	hw::reg<"UBRR0">::write(static_cast<std::uint8_t>(baud.ubrr));
 	hw::ucsr0a::write(hw::ucsr0a::u2x0(1));
 	// General-purpose registers are undefined at power-on (no crt zeroes them);
 	// the direction latch must start "not receiving" so the first rx() enables
@@ -262,15 +248,13 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 	// same reason.
 	g_receiving = 0;
 
-	// Activation: 3x'@', each inside the config page's timeout window (rx
+	// Activation: 3×'@', each inside the config page's timeout window (rx
-	// floors it so a corrupt page cannot lock the loader out); anything else  -
+	// floors it so a corrupt page cannot lock the loader out); anything else —
-	// including silence - hands over.
+	// including silence — hands over.
 	g_window = avr::flash_load(flash_ptr(app_end + 2));
-	for (std::uint8_t k = 3; k; --k) {
+	for (std::uint8_t k = 3; k; --k)
-		if (rx() != knock) {
+		if (rx() != knock)
 			appjump();
-		}
-	}
 	g_window = comm_window;
 
 	// Password gate (config page from app_end+3, 0xff-terminated; a blank
@@ -284,19 +268,17 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 		std::uint8_t expected = avr::flash_load(flash_ptr(g_addr)) & mask;
 		++g_addr;
 		if (expected == 0xff) {
-			g_addr = reinterpret_cast<std::uint16_t>(info.data());
+			g_addr = reinterpret_cast<std::uint16_t>(&info[0]);
 			g_cnt = sizeof(info);
 			sendf();
 			break;
 		}
 		std::uint8_t got = rx();
 		if (got == 0) {
-			if (mask == 0) {
+			if (mask == 0)
 				continue;
-			}
+			if (rcnf() != confirm || rcnf() != confirm)
-			if (rcnf() != confirm || rcnf() != confirm) {
 				appjump();
-			}
 			erase_application(); // leaves g_addr = 0 for the EEPROM walk
 			do {
 				eewr(0xff);
@@ -305,10 +287,9 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 			erase_below();
 			break;
 		}
-		if (got != expected) {
+		if (got != expected)
 			mask = 0;
 	}
-	}
 
 	for (;;) {
 		tx(confirm); // Mainloop ready
@@ -316,27 +297,23 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 		switch (rx()) {
 		case 'f': // read application flash, one page per host '!'
 			for (;;) {
-				if (rx() != confirm) {
+				if (rx() != confirm)
 					break;
-				}
 				g_cnt = page;
 				sendf();
-				if (g_addr >= app_end) {
+				if (g_addr >= app_end)
 					break;
 			}
-			}
 			break;
 		case 'F':                // erase the application, then take pages behind '?'
 			erase_application(); // leaves g_addr = 0, the write start
-			while (rcnf() == confirm) {
+			while (rcnf() == confirm)
 				store_flash();
-			}
 			break;
 		case 'e': // read EEPROM, one page per host '!', until the host stops
 			for (;;) {
-				if (rx() != confirm) {
+				if (rx() != confirm)
 					break;
-				}
 				g_cnt = page;
 				do {
 					tx(eerd());
@@ -358,9 +335,8 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 			sendf();
 			break;
 		case 'C': // replace the config page, then echo it back to verify
-			if (rcnf() != confirm) {
+			if (rcnf() != confirm)
 				break;
-			}
 			g_addr = app_end + page;
 			erase_below(); // leaves g_addr = app_end, the store target
 			store_flash();
@@ -374,6 +350,14 @@ extern "C" [[noreturn]] void tsb_app(); // the application's reset vector: --def
 } // namespace
 } // namespace tsb
 
-// Reset lands at the boot section base (BOOTRST): the entry stub in .vectors
+// Reset lands here: BOOTRST vectors to the boot section base and .vectors is
-// is laid first and does the one line of crt a crt-less image needs.
+// laid first, so this is the first instruction executed. No crt ran, so set
-template struct avr::startup::entry<tsb::run, avr::startup::stack::hardware>;
+// the stack pointer before anything is called.
+extern "C" [[gnu::naked, gnu::used, gnu::section(".vectors")]] void __boot_entry()
+{
+	SP = RAMEND;
+	// The one line of crt this loader needs: compiled code assumes
+	// __zero_reg__ (r1) is 0, and power-on registers are undefined.
+	asm volatile("clr __zero_reg__");
+	tsb::run();
+}