The pin crosses libavr's phase 6 - the renamed system surface, the named
serial configs, the receiver-tolerance table, the paged SPM receipts -
and every loader image comes out size-identical: the full matrix on six
representative chips (the exhaustive cross product on three of them),
the stock and autobaud columns untouched, the four tsb tiers back on
their recorded floors at 510/526/638/836.
Byte parity was not free, and the two libavr defects it surfaced were
fixed there rather than absorbed here. The EEPROM write procedure's
step 2 - the SPMEN spin - had landed unconditionally and cost every
build six bytes for a wait a polled loader can never take; it is scoped
now, and the loaders state the datasheet's own omission clause
(spm_interlock::omitted, DS40002061B 8.6.3). The blocking page
erase/write grew an internal wait the tiers' settle() already provides,
so the tiers issue the command form and pureboot keeps its host-driven
sp_spm path.
What the port states rather than inherits: the stock 115200 at 16 MHz
sits +2.1 % past the receiver-tolerance table libavr now holds rates
to, so the hardware links say .allow_baud_error = true - the same
2.5 % envelope pureboot_baud_feasible() has always enforced, proven on
silicon across the fleet. rx_ready() reads readable() now.
Alongside the pin: rule 33's ASCII sweep over every source (docs keep
their typography), rule 34's InsertBraces in .clang-format with the
tree reformatted, std::array over the simavr runners' raw buffers, and
the stale Studio size in ide/README.md replaced by the claim its
check-flags gate actually holds.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
--scan's walk was unwalkable on POSIX: probe rates have no termios
B-constant, so the first off-nominal probe raised out of the loop. The port
speaks termios2 BOTHER now (red-proven on a pty at 9984 Bd), the probe's
open lives inside the walk's error handling, an fd no longer leaks on an
unmakeable rate, and the swallowed unknown-signature reply is named at
timeout instead of reported as silence. CMakePresets.json's generator emits
the submodule toolchain path it had drifted from — a hand edit on a
generated file, exactly the class rule 10 exists for — and presets.generated
gates the pair from here on (the marker CMake rejects at the
presets root stayed out; the check is the guard). The over-slot image guard
the tsb runner gained reaches the pureboot runner too; the GPIO bridge's
delivery comment states the hardware truth (RXC at the stop bit's sampling
point); the hardware suite gains the scan check — the one place the rate
physics is real; and the libavr pin advances over both audit rounds.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
The RC-oscillator answer's host half. --scan probes ±10 % around the built
rate in 2 % steps, nearest first, one activation window (one reset) per
probe: a fixed-baud loader whose oscillator drifted answers at the ratio,
and the report gives the session workaround (--baud), the offset, the
OSCCAL direction at ~1 %/step, and the autobaud way out. The walk and the
advice are logic-tested (test_scan.py, red-proven on the trim direction) —
a pty carries bytes at any rate, so the wire cannot arbitrate them.
On an autobaud session --info now reads the measured bit period from
ram_start — the geometry table gains that column — and undoes the unit's
encoding ((cycles − 8) / 4, floored: libavr's spin granule and per-bit
overhead), so the printed clock is the true one within a granule; --clock
turns it into a stated drift. The autobaud end-to-end asserts the figure
inside exactly that envelope at both clock points.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
