Files
bootloader/test/pbapp.cpp
BlackMark e7f6cd3ee8 pureboot: the pin axis, and the mute it was hiding
Pins move the image for exactly one reason — a bit-banged link on a USART's own
pins has to release that USART — and the matrix said outright that they were no
axis, so the tightest configuration in the space was one nothing built. Not
subtly, either: the 1284's slot ends at flash end, so that build does not merely
exceed the size test's limit, it fails to link. pureboot_{sw,autobaud}_on_usart
{0,1} are gate points in both matrix modes now, and the exhaustive sweep carries
the pins across its whole cross product. The hand-measured table is the gate's
output: 506 B of 512 for the 1284 autobaud on USART0's pins, 504 on USART1's.

pureboot.mute drives the defect itself — an application hands over with USART0
still enabled and the loader on those pins must still answer. Reaching that
needed the runner to know an enabled USART owns its TxD, which simavr does not
model at all: it wires a USART through IRQs and never takes the pin from the
port. It also brings UCSRnB up with TXEN already set where silicon clears the
register, so the runner restores the reset value for the USART it models — the
mute must come from the application, not from power-on. The fixture stays
silent, since nothing is listening on the USART it brings up.

test_handshake.py, written where no gate could run it, is pureboot.handshake.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
2026-07-24 22:08:56 +02:00

140 lines
4.2 KiB
C++

// Test-fixture application for the pureboot protocol tests: prints "APP" on
// the chip's serial link (the same link the loader uses) — the proof that
// the loader's hand-over, and on the tinies the host's reset-vector
// surgery, actually launched it. Linked normally (crt, vectors at 0); on
// the tinies its reset vector is the rjmp the host re-homes.
//
// On the hardware-USART link it then listens, and an 'L' makes it jump into
// the resident loader — the application-owned loader entry a
// BOOTRST-unprogrammed mega relies on (reset always boots the application
// there), exercised by the self-update tests. The software link idles:
// reset reaches those loaders through the patched vector (or the runner
// models BOOTRST), so the application owes them nothing.
//
// PUREBOOT_HANDOVER drops the listening and jumps straight in, leaving the
// USART enabled behind it — the hand-over state a loader bit-banging on that
// USART's own pins has to survive.
//
// The fixture speaks the deployment its loader was built for: the same
// PUREBOOT_* defines configure it, and without them it assumes the stock
// deployment (the crystal/RC clock table below, the chip's natural link).
#include <libavr/libavr.hpp>
using namespace avr::literals;
namespace {
consteval avr::hertz_t clock()
{
#if defined(PUREBOOT_CLOCK_HZ)
return avr::hertz_t{PUREBOOT_CLOCK_HZ};
#else
auto name = std::string_view{avr::hw::db.name};
if (name.starts_with("ATtiny13"))
return 9.6_MHz;
if (name.starts_with("ATtiny"))
return 8_MHz;
return 16_MHz;
#endif
}
#if !defined(PUREBOOT_TX)
#define PUREBOOT_TX pb1
#endif
#if !defined(PUREBOOT_USART)
#define PUREBOOT_USART 0
#endif
consteval bool use_hardware()
{
#if defined(PUREBOOT_SOFT_SERIAL)
return false;
#else
return avr::hw::db.has_instance("USART0") || avr::hw::db.has_instance("USART");
#endif
}
using dev = avr::device<{.clock = clock()}>;
template <avr::hertz_t C, bool Hardware = use_hardware()>
struct link {
#if defined(PUREBOOT_BAUD)
static constexpr avr::baud_t baud{PUREBOOT_BAUD};
#else
static constexpr avr::baud_t baud{115200};
#endif
using tx_t = avr::uart::usart<'0' + PUREBOOT_USART, C, {.baud = baud, .max_baud_error = 2.5_pct}>;
static void tx(char c)
{
tx_t::write(static_cast<std::uint8_t>(c));
}
// The loader sits in the top slot — 512 bytes on every chip. The jump
// takes a word address, which is what makes the >64 KiB chips' entry
// reachable through a 16-bit pointer at all.
static void enter_loader()
{
constexpr std::uint32_t slot = 512;
reinterpret_cast<void (*)()>(static_cast<std::uint16_t>((avr::hw::db.mem.flash_size - slot) / 2))();
}
[[noreturn]] static void idle()
{
#if defined(PUREBOOT_HANDOVER)
// Hand back at once, with this USART still enabled — the state that
// leaves a bit-banged loader on its pins mute unless the loader
// releases it. Unconditional because there is no command wire to
// wait on: that loader's link is the pins, not this peripheral.
enter_loader();
__builtin_unreachable();
#else
for (;;) {
auto command = tx_t::read_blocking();
if (command == 'L')
enter_loader();
// 'D' leaves every word of the SPM page buffer dirty, so that a
// following 'L' enters the loader with the buffer it never clears.
if (command == 'D') {
for (std::uint16_t at = 0; at < avr::spm::page_bytes; at += 2)
avr::spm::fill(at, 0xdead);
tx('D');
}
}
#endif
}
};
template <avr::hertz_t C>
struct link<C, false> {
#if defined(PUREBOOT_BAUD)
static constexpr avr::baud_t baud{PUREBOOT_BAUD};
#else
static constexpr avr::baud_t baud{57600};
#endif
using tx_t = avr::uart::software_tx<C, avr::PUREBOOT_TX, baud>;
static void tx(char c)
{
tx_t::write(static_cast<std::uint8_t>(c));
}
[[noreturn]] static void idle()
{
while (true) {
}
}
};
} // namespace
int main()
{
avr::init<typename link<dev::clock>::tx_t>();
#if !defined(PUREBOOT_HANDOVER)
link<dev::clock>::tx('A');
link<dev::clock>::tx('P');
link<dev::clock>::tx('P');
#endif
// The hand-over fixture stays silent: nothing is listening on the USART it
// brings up — the loader it hands to speaks those pins directly — so its
// banner would be a write into a peer that does not exist.
link<dev::clock>::idle();
}