HALF_DUPLEX deploys a shared line per backend. The hardware USART takes
the library's .half_duplex turn-around — RXD and TXD tied off-chip, each
reply byte held to transmit-complete before the line can be released
(m8 404 B, m328P 440, 1284P 460; the window poll runs through the
outlined release-line call at 18 or 22 cycles a poll, measured off the
built loops and held per chip by pureboot.window.halfduplex). The
software and autobaud links fold onto the RX pin — RX == TX spells the
same — and cost nothing: the frame's direction wrap is what the dropped
second-pin init paid, and the worst image in the space is unchanged at
the 1284s' 502 of 512, now with its one-wire twin proven equal across
the exhaustive matrix. The host gains --one-wire, the echo discard a
shared line requires: the adapter's echo is matched byte for byte and a
reply interleaving a blind write — a loader already in session
re-prompts inside the knock — is held for the reader. The device runner
models the shared line by direction (drives only while the firmware's
DDR reads input, decodes only while the firmware owns it, supplies the
host-side echo), extends the USART pin-ownership model to RXEN's hold
on RXD, and starts the pty USART from the datasheet's zeroed UCSR#B:
simavr's TXEN-set reset plus its clear-UDRE-on-TXEN-drop otherwise
wedges the first transmitter after a receiver-only program, which the
half-duplex window gate caught as a banner that never came. v7 is
tagged at its era's last commit; v8 changes nothing on the wire.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
sizes.py merged every owned tree's rows and let the last one win, so a
stale reflect tree — last built before the window constants moved —
reported the atmega8's old stock size over the fresh build and failed
the README check with yesterday's number. Generated and reflect must
answer with the same bytes (the identity invariant), so the same target
measuring two sizes is a stale tree or an identity breach; collect()
refuses now, naming both trees. The stale reflect trees are removed —
the reflect sweep rebuilds them.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
The window's per-poll cycle counts were hand-counted for a uint32_t
countdown, but every default window fits uint24_t, whose decrement chain
is one sbci shorter — so deployed loaders ran 9/10ths of their stated
seconds (a 328P's 8 s was 7.2 s on the wire). No golden-asm pin can hold
this: the loops compile in consumer context. pbwindow.py measures the
behavior instead: it installs a real application beside the loader
through the host tool's own plan_flash (surgery included), starts the
simulator with the line idle, and reads the cycle of the first transmit
— the application's banner, so that cycle is the window. Held at plus or
minus 2 percent per chip (pureboot.window), red at -10.0 percent against
the old constants, green with poll_cycles now counted for the narrow
countdown (hardware 9, software 7; window_polls() solves narrow-first
and adds the wide loop's cycle where the count forces uint32_t — a count
narrow only at the wide cost stays wide, so the choice cannot
oscillate). The autobaud window is its poll budget at the measured ten
cycles a poll, gated the same way (pureboot.window.autobaud), and the
README carries that arithmetic now. No version bump: timing-window
precision is not meaningful behavior, v7 stays.
The gate flushed out two runner gaps. The software bridge accepted any
falling edge as a start bit, so the device's own TX-init glitch decoded
as a stray byte; it re-samples mid-bit now and abandons a false start,
as silicon does. And after avr_reset, the idle-line re-raise was
silently dropped: ioport pin irqs are IRQ_FLAG_FILTERED and the irq's
cached value survives the reset the port latch does not, so the device
read the line stuck low, calibrate() measured reset-to-first-edge as one
wrapping pulse, and the first knock after a reset could boot the
application instead of locking — the intermittent autobaud failure.
bridge_reset forces a real transition (0 then 1, no cycles between).
The README's Autobaud column now carries each chip's worst
configuration — autobaud with OSCCAL baked, on a USART's own pins where
the chip has one (tinies: autobaud + OSCCAL) — the numbers the existing
pureboot_autobaud_osccal[_on_usart0] matrix points already gate;
sizes.py checks the column against exactly those targets. Tool sizes
and window prose updated with it.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
The size matrix proves every image fits its slot and says nothing about the
numbers the README prints. Those drift silently: caller_page() took eight bytes
off every build at once, so all fifteen rows went stale together and no test
noticed, because nothing was over budget. sizes.py check-readme compares the
table against the built images; sizes.py max reports the largest image per chip
and anything over its slot.
It is a check rather than a generator, so the table stays prose someone can
write. No chip geometry lives here either: the image/budget pairs come out of
each build's own CTestTestfile.cmake, which is what the gate checks, so a chip
added or a budget changed needs no edit. Only trees a preset still owns are
read — a stale directory answers with a size that was true once.
16243 images across 37 chips today, none over budget, tightest tsb_asm at 510
of 512.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
