The flag was plumbed through pbrig.Deployment to the host-tool subprocess
calls and nowhere else, so identity() and scan() opened a raw port and drove
a shared line as though it were two wires. On real one-wire hardware the
adapter's echo answers the knock before the device does, so the suite would
have died at its very first check — "the loader never answered; nothing below
can be trusted" — for the one deployment the flag exists to test, and every
result after it is gated on that check passing.
Both now open through pbrig.Rig.open_port(), which applies the deployment's
link mode. The gap underneath was that only the subprocess path could reach
those facts at all; anything driving the protocol in-process had to restate
them, and did not.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
HALF_DUPLEX deploys a shared line per backend. The hardware USART takes
the library's .half_duplex turn-around — RXD and TXD tied off-chip, each
reply byte held to transmit-complete before the line can be released
(m8 404 B, m328P 440, 1284P 460; the window poll runs through the
outlined release-line call at 18 or 22 cycles a poll, measured off the
built loops and held per chip by pureboot.window.halfduplex). The
software and autobaud links fold onto the RX pin — RX == TX spells the
same — and cost nothing: the frame's direction wrap is what the dropped
second-pin init paid, and the worst image in the space is unchanged at
the 1284s' 502 of 512, now with its one-wire twin proven equal across
the exhaustive matrix. The host gains --one-wire, the echo discard a
shared line requires: the adapter's echo is matched byte for byte and a
reply interleaving a blind write — a loader already in session
re-prompts inside the knock — is held for the reader. The device runner
models the shared line by direction (drives only while the firmware's
DDR reads input, decodes only while the firmware owns it, supplies the
host-side echo), extends the USART pin-ownership model to RXEN's hold
on RXD, and starts the pty USART from the datasheet's zeroed UCSR#B:
simavr's TXEN-set reset plus its clear-UDRE-on-TXEN-drop otherwise
wedges the first transmitter after a receiver-only program, which the
half-duplex window gate caught as a banner that never came. v7 is
tagged at its era's last commit; v8 changes nothing on the wire.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
check.sh proves the protocol under simavr on every chip; it cannot prove a
board. Two things live only on silicon — an RC oscillator that is not on its
nominal, and a reset edge that has to come from somewhere — and until now the
scripts that reached them were per-session scratch on the machine holding the
programmer, which is where the ATtiny13A run's findings nearly stayed.
pbrig.py is the primitives, knowing nothing per-board: every deployment fact is
a flag or a PUREBOOT_* variable. Two rig facts are encoded in it because neither
is guessable and each cost a session to learn: an ISP access *is* the reset edge
where the adapter's DTR is unwired, so a session begins with an ISP touch and
knocks immediately after; and avrdude splits -U on colons, so a Windows drive
letter breaks the spec and every file goes as a bare name with avrdude run in
its own directory. Its `rate` subcommand is the one that turns "the loader is
silent, so the wiring must be wrong" into a number, by sweeping the host rate
against a fixed cycles-per-bit transmitter — PUREBOOT_HEARTBEAT makes the
existing fixture into one, software link only, since the hardware-link idle owes
the self-update tests its command loop.
pbhw.py takes every bound from the info block the loader reports, so one run
covers a 1 KiB tiny and a 128 KiB mega alike. Both are exercised on an ATtiny13A:
backup verified against a known-good capture, the clock measured at 9.048 MHz
against a 9.6 MHz nominal, and the suite 11/11.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
