The pin crosses libavr's phase-6 close and the guideline sweep behind it.
All 37 chips green, 43 tests each, the README size table matching every
built image, and all 13602 flash images byte-identical to the previous pin.
The bump broke one gate and exposed another as ornamental.
`check_unit.cmake` matched the autobaud loader's measured unit by the symbol
`unit_E`; libavr's rule-46 sweep renamed the member to `m_unit`, which the
mangling spells `6m_unitE`. On the RAM-home chips the check went red and said
so. On the GPIOR chips it went green - the branch that asserts the unit is
*not* in RAM passes on an empty match, and an empty match is what a stale
regex returns for every image. Both branches mean something again.
`tools/check.sh` ran the 37-chip loop under `set -e`, so the first red chip
ended the gate and the 36 behind it were never built - a stale size canary on
attiny13 would have been an alibi for every loader after it. It accumulates
now and fails at the end naming every red preset, which is the shape libavr's
own check.sh carries and the reason it carries it.
The port's own sweep, verified by byte identity: the four TSB tiers' 16-byte
info block is `std::to_array` rather than an extent written beside the
sixteen elements the compiler can count, the three-member serial and loader
configs break one member per line, the turn-around loops are braced, and the
test fixture's config pair is a deduced `std::array` (rules 36, 40, 34). Two
comments stop narrating how the code came to be and one stops citing a repro
at a path it left two phases ago (rules 12, 13).
pureboot's identity stamp stays the raw array rule 36 bans, and now says why:
its reads must fold to immediates because the bytes are in program memory and
a formed address is dereferenced as data space. As a `std::array` the read
loop stopped unrolling and emitted exactly that - measured at +8 B and a
wrong answer on the wire.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
The pin crosses libavr's phase 6 - the renamed system surface, the named
serial configs, the receiver-tolerance table, the paged SPM receipts -
and every loader image comes out size-identical: the full matrix on six
representative chips (the exhaustive cross product on three of them),
the stock and autobaud columns untouched, the four tsb tiers back on
their recorded floors at 510/526/638/836.
Byte parity was not free, and the two libavr defects it surfaced were
fixed there rather than absorbed here. The EEPROM write procedure's
step 2 - the SPMEN spin - had landed unconditionally and cost every
build six bytes for a wait a polled loader can never take; it is scoped
now, and the loaders state the datasheet's own omission clause
(spm_interlock::omitted, DS40002061B 8.6.3). The blocking page
erase/write grew an internal wait the tiers' settle() already provides,
so the tiers issue the command form and pureboot keeps its host-driven
sp_spm path.
What the port states rather than inherits: the stock 115200 at 16 MHz
sits +2.1 % past the receiver-tolerance table libavr now holds rates
to, so the hardware links say .allow_baud_error = true - the same
2.5 % envelope pureboot_baud_feasible() has always enforced, proven on
silicon across the fleet. rx_ready() reads readable() now.
Alongside the pin: rule 33's ASCII sweep over every source (docs keep
their typography), rule 34's InsertBraces in .clang-format with the
tree reformatted, std::array over the simavr runners' raw buffers, and
the stale Studio size in ide/README.md replaced by the claim its
check-flags gate actually holds.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
HALF_DUPLEX deploys a shared line per backend. The hardware USART takes
the library's .half_duplex turn-around — RXD and TXD tied off-chip, each
reply byte held to transmit-complete before the line can be released
(m8 404 B, m328P 440, 1284P 460; the window poll runs through the
outlined release-line call at 18 or 22 cycles a poll, measured off the
built loops and held per chip by pureboot.window.halfduplex). The
software and autobaud links fold onto the RX pin — RX == TX spells the
same — and cost nothing: the frame's direction wrap is what the dropped
second-pin init paid, and the worst image in the space is unchanged at
the 1284s' 502 of 512, now with its one-wire twin proven equal across
the exhaustive matrix. The host gains --one-wire, the echo discard a
shared line requires: the adapter's echo is matched byte for byte and a
reply interleaving a blind write — a loader already in session
re-prompts inside the knock — is held for the reader. The device runner
models the shared line by direction (drives only while the firmware's
DDR reads input, decodes only while the firmware owns it, supplies the
host-side echo), extends the USART pin-ownership model to RXEN's hold
on RXD, and starts the pty USART from the datasheet's zeroed UCSR#B:
simavr's TXEN-set reset plus its clear-UDRE-on-TXEN-drop otherwise
wedges the first transmitter after a receiver-only program, which the
half-duplex window gate caught as a banner that never came. v7 is
tagged at its era's last commit; v8 changes nothing on the wire.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Four cuts, none touching what the loader can do. The entry stub stops
re-doing the reset logic's own SP write where the datasheet guarantees
RAMEND (stack::hardware — the classic megas keep theirs). The autobaud
unit moves into GPIOR2:GPIOR1 wherever the chip has the pair: one-word
accesses, no RAM object, and the host's measured-clock peek follows it
by version and geometry. 'J' rides the unified decode, carrying a
selector it ignores so its address is the same two reads as every other
command — the tool sends the bare form to older residents. run_app stops
insisting on a body of its own. The fleet lands at 358–410 B stock and
438–474 B autobaud; the tightest image in the space — the 1284s'
autobaud on a USART's own pins with the OSCCAL trim — drops from 510 to
484 of its 512. Every chip's suite is green on the wire that changed,
and the README's table is machine-checked against the built images.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
The RC-oscillator answer's host half. --scan probes ±10 % around the built
rate in 2 % steps, nearest first, one activation window (one reset) per
probe: a fixed-baud loader whose oscillator drifted answers at the ratio,
and the report gives the session workaround (--baud), the offset, the
OSCCAL direction at ~1 %/step, and the autobaud way out. The walk and the
advice are logic-tested (test_scan.py, red-proven on the trim direction) —
a pty carries bytes at any rate, so the wire cannot arbitrate them.
On an autobaud session --info now reads the measured bit period from
ram_start — the geometry table gains that column — and undoes the unit's
encoding ((cycles − 8) / 4, floored: libavr's spin granule and per-bit
overhead), so the printed clock is the true one within a granule; --clock
turns it into a stated drift. The autobaud end-to-end asserts the figure
inside exactly that envelope at both clock points.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
The ATtiny13A run left autobaud's low-clock lock looking unreliable: 1/5 at
19200 on a 1.2 MHz RC part. The simulator does not reproduce it. At an exact
clock the calibration is solid down to ~36 cycles a bit and fails outright by
~31 — a sharp edge, not a fraying one — where the real part was already 1 in 5
by ~59. So the effect is the oscillator's own jitter and not backend logic, and
the two floors are different quantities about a factor of two apart.
Both are worth having. pureboot.autobaud gates a tight-bit point, since its two
existing clock points both sat near 100 cycles a bit and would not notice the
floor moving. The README carries the other half: both floors side by side, the
per-clock envelope measured on silicon, and the reason budgeting the logic's ~36
on an RC part is wrong.
It also carries the trap that produced the confusion. On a patched-vector chip an
erased application region walks back up into the loader, so every expired window
opens another and the host's retries eventually catch the pulse — 5/5 where the
same part with an application resident gives 1/5. Measure with an application in
place, or the fixture flatters the backend.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Hardware testing found that a lone calibration pulse wedged the autobaud loader:
run() budgeted only the start-edge wait in measure(), and the rx() that read the
knock behind it was unbudgeted, so one stray low pulse held an unattended device
in the loader and the application never ran. Bound the whole activation — an
expired knock budget returns a byte that cannot be the knock, so control falls
back into the budgeted measure() and an idle line boots the app there.
That fix costs ~22 B, which neither version under review could absorb: the pure
one goes 508 -> 530 on the 1284P and the register one 512 -> 534, both over a
512 B slot. Their margin was never spare capacity, it was the space the missing
fix should have occupied. So the choice between them is moot; both are kept for
the record and no longer built.
pureboot_autobaud_uni.cpp replaces them at 464 B. It is pureboot 5: one read
command and one write command over named spaces (G/g, sel8, addr16, n8) instead
of four per-memory bodies, which collapses four transfer loops into one. The
selector's high nibble carries flash's bank, so the shared cursor stays 16 bits
and no command speaks word addresses. Three things fall out of the freed space:
RAM read/write — the missing feature, and with it arbitrary I/O access, since
AVR maps peripherals into the data space; host-issued SPM, so W's hardcoded
erase/write/RWW tail becomes three writes to a space and any SPM operation is
reachable; and W on the same selector-and-address decode as everything else.
Strictly pure throughout: no inline asm, no global register variable, and no
GPIOR either — the unit lives in a .noinit static, so the loader claims no chip
resource and the chips without GPIOR stop being a special case.
pureboot.py speaks both generations, keyed on the version, so the fixed-baud
path is untouched; --peek/--poke reach the new data space. pbautobaud.py adds a
RAM round-trip and a regression for the hang: a lone pulse must still let the
app boot. All 37 chips plus the 12-preset reflect spot set build and size-test
green, 444-466 B, worst case 46 B under budget. Sim suites 100%: 1284P 17/17,
328P 23/23. Only real-hardware acceptance remains (pureboot/autobaud.md).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
pureboot.py --autobaud sends the 0xC0 calibration pulse and a single knock at
the host's chosen baud, reads the slimmed info block, and derives the full
geometry from the signature (AUTOBAUD_GEOMETRY, a table over every pureboot
chip). Everything downstream — flash, EEPROM, fuses, hand-over, verify — is the
fixed-baud path unchanged; the dropped write guard is host-transparent.
test/pbautobaud.py drives each variant over the GPIO⇄pty software-UART bridge
through the calibration handshake and a flash + EEPROM + fuse round-trip
cross-checked against the simulator's ground-truth memory, then repeats at
double the F_CPU with the same binary — the clock-agnostic property autobaud
exists for. Wired as pureboot.autobaud_pure/reg on the near-flash 328P and the
word-addressed 1284P. A wrong measured unit fails the flash/verify, so the test
also pins the codegen-coupled calibration constant against a toolchain bump.
Both variants green in sim on both chips at two clocks each; the fixed-baud
suite is unaffected. Only real-hardware acceptance on an RC part remains
(pureboot/autobaud.md).
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
