avr/bootloader
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
Files
0ddc65ca289fed396c5ee115dddaecaaf6ef913f
bootloader/CMakeLists.txt
BlackMark a285347e5f pureboot 5: one command pair for every memory, and a clock-free backend 
R/r/w/F collapse into G and g over a selector byte naming the space — flash,
EEPROM, data, fuse, SPM — with the flash bank in its high nibble. Four command
bodies, four transfer loops and four argument decodes become one of each, and
W joins the same decode instead of keeping an address form of its own. The
loader shrinks while gaining everything below: on the 1284P the stock build
goes 480 -> 432 B and the software one 496 -> 450.

What the freed space buys:

  - Data space. On AVR one pointer spans SRAM, the register file and the whole
    I/O space, so G over space 2 reads all three. pureboot keeps zero static
    RAM and pushes no register, so at loader entry an application's SRAM is
    still what the application left there — this is a post-mortem, not just a
    poke hole. As its own command it needed a dispatch arm and a loop; as one
    more space it is a single ld/st.
  - Host-issued SPM. W fills the page buffer and stops; erase, write and RWW
    re-enable are writes to space 4, which reach the same fused store-and-SPM
    pair through the transfer's own address and data. Any SPM operation, lock
    bits included, is now reachable and the loader carries no page-commit logic.
    The four-cycle SPMCSR-to-SPM window is why that primitive stays fused: no
    host can hit it across a serial link, and that — not the byte count — is
    the floor on how low-level a bootloader's primitives can go.
  - Byte addresses everywhere. The bank in the selector retires the
    word-addressed wire the >64 KiB parts needed, so the 1284s stop being the
    outlier.

SERIAL autobaud is a third backend on the same loader, over libavr's
software_autobaud: no clock, no baud, one binary per chip for every F_CPU and
every rate. Activation counts poll iterations rather than seconds and bounds
every wait, so a stray pulse cannot hold an unattended device.

b answers with the version and signature only; the host derives geometry from
the signature, which is what an autobaud build requires anyway. An update image
is a bare slot with no device to ask, so every image carries a six-byte stamp —
the same bytes b answers with, and the source of both — that the loader never
reads from flash and the host refuses to install a mismatch against. The
running-slot write guard moved onto the SPM commit, which covers erase and
write both where guarding W covered neither directly.

The position-independence lint now proves the property instead of a proxy for
it: the image must come out byte-identical linked at a different base.
-fno-move-loop-invariants left the tuned flag set — it was fitted to a command
loop carrying four transfer bodies and costs bytes now that it carries one.

Verified: the exhaustive matrix on all 37 chips (every clock x every baud x
every backend, non-standard rates included, plus the autobaud build) —
8174 size checks, no failures, tightest fit the 1284s' autobaud at 510 of 512.
Behavioral suites green on every chip class: t13a 10/10, t85 11/11, m8 13/13,
m16a 13/13, m48pa 13/13, 328P 23/23, 644A 17/17, 1284P 17/17. Data-space
round trip through --peek/--poke and the autobaud handshake are both red-green
proven.

The two prototype sources and their findings file go; the README carries the
protocol and dev/done.md in libavr carries the reasoning.

Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
2026-07-24 15:50:48 +02:00

414 lines
22 KiB
CMake
Raw Blame History

cmake_minimum_required(VERSION 3.28)
project(tsb_libavr LANGUAGES CXX)
# libavr from a local checkout (LIBAVR_ROOT) or the forge; the toolchain file
# comes from the same checkout via CMakePresets.json.
include(FetchContent)
if(NOT LIBAVR_ROOT AND DEFINED ENV{LIBAVR_ROOT})
set(LIBAVR_ROOT $ENV{LIBAVR_ROOT})
endif()
if(LIBAVR_ROOT)
FetchContent_Declare(libavr SOURCE_DIR ${LIBAVR_ROOT})
else()
FetchContent_Declare(libavr GIT_REPOSITORY git@git.blackmark.me:avr/libavr.git GIT_TAG main)
endif()
FetchContent_MakeAvailable(libavr)
if(PROJECT_IS_TOP_LEVEL)
add_compile_options(-Werror) # warnings are errors for the port's own code
enable_testing()
# The behavioral tests drive the real wire protocols over a simavr pty
# (as the host tools do) and actually flash the device. The runners are
# host programs built at configure time against libsimavr; if they or
# Python are missing, only the size tests run.
find_program(_host_cc NAMES cc gcc)
find_package(Python3 COMPONENTS Interpreter)
if(_host_cc AND Python3_FOUND)
set(PB_DEVICE ${CMAKE_BINARY_DIR}/pureboot_device)
execute_process(
COMMAND ${_host_cc} -O2 -I/usr/include/simavr -I/usr/include/simavr/parts
-o ${PB_DEVICE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pureboot_device.c
-lsimavr -lsimavrparts -lelf -lutil
RESULT_VARIABLE _pbdev_res ERROR_VARIABLE _pbdev_err)
if(NOT _pbdev_res EQUAL 0)
message(STATUS "pureboot_device not built (${_pbdev_err}) — protocol tests skipped")
unset(PB_DEVICE)
endif()
if(LIBAVR_MCU STREQUAL "atmega328p")
set(TSB_DEVICE ${CMAKE_BINARY_DIR}/tsb_device)
execute_process(
COMMAND ${_host_cc} -O2 -I/usr/include/simavr -I/usr/include/simavr/parts
-o ${TSB_DEVICE} ${CMAKE_CURRENT_SOURCE_DIR}/test/device.c
-lsimavr -lsimavrparts -lelf
RESULT_VARIABLE _dev_res ERROR_VARIABLE _dev_err)
if(NOT _dev_res EQUAL 0)
message(STATUS "tsb_device not built (${_dev_err}) — protocol tests skipped")
unset(TSB_DEVICE)
endif()
endif()
endif()
endif()
# The ELF is only a container (symbols, section headers) and is never flashed —
# and the host tool's load_image() dispatches on extension, so handing it one
# would silently program the header bytes. Every loader image therefore gets
# both flashable forms beside it at link time: .hex for avrdude, and .bin for
# the host tool's raw path (which is what the reloc and update tests convert to
# on the fly). .eeprom is dropped — EEPROM content is its own update.
function(add_image_outputs name)
add_custom_command(TARGET ${name} POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O ihex -R .eeprom
$<TARGET_FILE:${name}> $<TARGET_FILE:${name}>.hex
COMMAND ${CMAKE_OBJCOPY} -O binary -R .eeprom
$<TARGET_FILE:${name}> $<TARGET_FILE:${name}>.bin)
endfunction()
# The TinySafeBoot protocol reimplemented on libavr in three variants that trade
# clarity for size. Each links into the ATmega328P boot section (BOOTSZ selects
# its size; BOOTRST vectors a reset to its base) with -nostartfiles — a polled
# loader has no use for the crt or the vector table. The naked entry sits in
# .vectors, laid first, and runs. The boot base is FLASHEND+1 minus the section
# size; the linker section-start and the source's boot_bytes agree. tsb_app is
# the application's reset vector, pinned to 0 here so the loaders jump to a
# named function; --pmem-wrap-around lets relaxation turn that absolute jump
# into the wrapped rjmp AVR's modulo-flash PC actually executes.
# All three implement the full oracle feature set (see oracle/README.md):
# watchdog bail, one-wire half-duplex, config-page activation timeout, password
# gate, emergency erase, config/flash/EEPROM read-write. They differ only in how,
# and the size gradient is the cost of that "how" — see dev/lessons.md.
# tsb_asm — the tricks tier's C++ with exactly two routines in asm (the
# bounded rx and the page-store loop — the two whose remaining
# cost is the C ABI itself): 510 B in the 512 B section the
# hand-written 500 B oracle occupies. Everything else, from
# bring-up to dispatch, is C++ on libavr.
# tsb_tricks — no asm at all: the whole-loader register allocation lives in
# global register variables (Y walks the page pointer), every
# helper is a tiny noinline primitive placed by the
# global-register store rules, pages stream straight to
# SPM/EEPROM, and the bring-up is the two reset-non-default
# registers only. 526 B in the 1 KB section (BOOTSZ=10) — 14
# over the oracle's section, from 168 over at this tier's first
# floor.
# tsb_pure — pure idiomatic libavr, one function per command, TU-local
# (internal linkage), streaming (no SRAM page buffer): 836 B in
# the 1 KB section.
#
# add_tsb_variant(<name> <boot-section-bytes>)
function(add_tsb_variant name bytes)
math(EXPR base_dec "32768 - ${bytes}")
math(EXPR base_hex "${base_dec}" OUTPUT_FORMAT HEXADECIMAL)
add_executable(${name} tsb/${name}.cpp)
target_link_libraries(${name} PRIVATE libavr)
target_link_options(${name} PRIVATE -nostartfiles -Wl,--section-start=.text=${base_hex}
-Wl,--defsym=tsb_app=0 -Wl,--pmem-wrap-around=32k)
add_custom_command(TARGET ${name} POST_BUILD COMMAND ${CMAKE_SIZE} $<TARGET_FILE:${name}>)
add_image_outputs(${name})
if(PROJECT_IS_TOP_LEVEL)
add_test(NAME ${name}.size
COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:${name}>
-DLIMIT=${bytes} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
if(DEFINED TSB_DEVICE)
add_test(NAME ${name}.protocol
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/tsbtest.py
${TSB_DEVICE} $<TARGET_FILE:${name}> ${base_hex})
endif()
endif()
endfunction()
# The tsb tiers reimplement the ATmega328P-only reference protocol; the other
# chips build pureboot alone.
if(LIBAVR_MCU STREQUAL "atmega328p")
add_tsb_variant(tsb_asm 512)
add_tsb_variant(tsb_pure 1024)
add_tsb_variant(tsb_tricks 1024)
endif()
# pureboot — the pure-constraint port (see pureboot/README.md): one source,
# no inline assembly, no global register variables, every libavr chip,
# fitting each chip's smallest boot sector. The geometry and the
# pureboot_add_loader() deployment function live in pureboot/CMakeLists.txt —
# the unit a downstream project consumes; everything below is this port's
# own build: the stock loaders, their tests, and the size matrix. The
# distinct binary dir keeps the `pureboot` target's output name free.
add_subdirectory(pureboot pureboot-cmake)
# The stock loader: the family-default deployment (crystal/RC clock, the
# chip's natural link, default pins). The activation window stays a cache
# variable — re-timing a deployed loader is a self-update with a re-timed
# build. pureboot9 is that re-timed build, and what the update test installs.
set(PUREBOOT_TIMEOUT 8 CACHE STRING "pureboot activation window, seconds")
pureboot_add_loader(pureboot TIMEOUT ${PUREBOOT_TIMEOUT})
if(PROJECT_IS_TOP_LEVEL)
get_target_property(_pb_stock_hz pureboot PUREBOOT_HZ)
get_target_property(_pb_stock_baud pureboot PUREBOOT_BAUD)
add_test(NAME pureboot.size
COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:pureboot>
-DLIMIT=${PUREBOOT_LIMIT} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
if(Python3_FOUND)
add_test(NAME pureboot.pi
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/check_pi.py
${CMAKE_OBJDUMP} ${CMAKE_OBJCOPY} ${CMAKE_CXX_COMPILER} ${LIBAVR_MCU}
$<TARGET_FILE:pureboot>
${CMAKE_BINARY_DIR}/CMakeFiles/pureboot.dir/pureboot/pureboot.cpp.obj
${PUREBOOT_BASE_HEX})
add_test(NAME pureboot.planner
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/test_planner.py
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py)
endif()
# The protocol test flashes this fixture through the loader with the real
# host tool and expects its banner after the hand-over; a normally linked
# application whose reset vector is what the tinies' surgery re-homes.
if(DEFINED PB_DEVICE)
add_executable(pbapp test/pbapp.cpp)
target_link_libraries(pbapp PRIVATE libavr)
add_custom_command(TARGET pbapp POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary $<TARGET_FILE:pbapp> $<TARGET_FILE:pbapp>.bin)
add_test(NAME pureboot.protocol
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
${PB_DEVICE} $<TARGET_FILE:pureboot> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud} ${PUREBOOT_EEPROM}
$<TARGET_FILE:pbapp>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbtest-work)
set_tests_properties(pureboot.protocol PROPERTIES TIMEOUT 180)
# The position-independence acceptance test: the identical image,
# installed one slot lower, must serve the full command set.
add_test(NAME pureboot.reloc
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbreloc.py
${PB_DEVICE} $<TARGET_FILE:pureboot> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud}
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbreloc-work)
set_tests_properties(pureboot.reloc PROPERTIES TIMEOUT 180
ENVIRONMENT "PB_OBJCOPY=${CMAKE_OBJCOPY}")
# Entering the loader from a running application with no reset
# between, over a page buffer the application dirtied — the case the
# loader declines to guard and the host repairs. Hardware forbids the
# state here (SPM runs only from the boot section); simavr does not,
# which is what makes it constructible.
if(LIBAVR_MCU STREQUAL "atmega328p")
add_test(NAME pureboot.dirty
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbdirty.py
${PB_DEVICE} $<TARGET_FILE:pureboot> ${PUREBOOT_SIM_MCU} ${_pb_stock_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_pb_stock_baud}
$<TARGET_FILE:pbapp>.bin
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbdirty-work)
set_tests_properties(pureboot.dirty PROPERTIES TIMEOUT 180)
endif()
# Re-homing: a loader mistakenly programmed at address 0 (a raw .bin
# handed to a programmer) or sitting in the staging slot must heal
# into the canonical slot through the ordinary --update-loader flow.
# Patched-vector behavior, so one representative chip carries it.
if(LIBAVR_MCU STREQUAL "attiny85")
add_test(NAME pureboot.rehome
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbrehome.py
${PB_DEVICE} $<TARGET_FILE:pureboot> $<TARGET_FILE:pureboot9>.bin
${PUREBOOT_SIM_MCU} ${_pb_stock_hz} ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE}
${_pb_stock_baud} $<TARGET_FILE:pbapp>.bin
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbrehome-work)
set_tests_properties(pureboot.rehome PROPERTIES TIMEOUT 180)
endif()
# The self-update end-to-end: the re-timed build (same source, only
# the timeout differs — a byte-different image) replaces the resident
# through --update-loader, with every power-fail phase rehearsed from
# the runner's flash dumps.
pureboot_add_loader(pureboot9 TIMEOUT 9)
add_test(NAME pureboot.update
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbupdate.py
${PB_DEVICE} $<TARGET_FILE:pureboot> $<TARGET_FILE:pureboot9>
${PUREBOOT_SIM_MCU} ${_pb_stock_hz} ${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE}
${_pb_stock_baud} $<TARGET_FILE:pbapp>.bin
${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbupdate-work)
set_tests_properties(pureboot.update PROPERTIES TIMEOUT 600
ENVIRONMENT "PB_OBJCOPY=${CMAKE_OBJCOPY}")
endif()
# The size matrix: every configuration axis that could move the image
# size — the serial backend (different code), the USART instance
# (different registers), the clock (different constants), and the baud
# through the shapes its bit timing takes — each combination must still
# fit the chip's slot budget. Pins are size-neutral (port and bit are
# immediate operands) and the timeout is a constant, so neither adds an
# axis. The stock build is one point of this matrix and already has its
# test.
function(pureboot_size_variant name)
pureboot_add_loader(${name} ${ARGN})
add_test(NAME ${name}.size
COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:${name}>
-DLIMIT=${PUREBOOT_LIMIT} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
endfunction()
# The autobaud loader: one clock-agnostic image per chip, so it has no
# clock x baud axis of its own — the matrix below sweeps those for the
# fixed-baud builds, and this one binary has to serve all of them at run
# time. Size-tested against the same per-chip budget as every other variant.
pureboot_add_loader(pureboot_autobaud SERIAL autobaud)
add_test(NAME pureboot_autobaud.size
COMMAND ${CMAKE_COMMAND} -DSIZE_TOOL=${CMAKE_SIZE} -DELF=$<TARGET_FILE:pureboot_autobaud>
-DLIMIT=${PUREBOOT_LIMIT} -P ${CMAKE_CURRENT_SOURCE_DIR}/test/check_size.cmake)
# One point of the exhaustive matrix, named from its resolved parameters
# so the enumeration cannot collide with itself. Unreachable rates drop
# out here rather than aborting the configure.
function(pureboot_matrix_point hz baud link)
if(link STREQUAL "software")
pureboot_baud_feasible(${hz} ${baud} 1 _ok)
set(_args SERIAL software)
else()
pureboot_baud_feasible(${hz} ${baud} 0 _ok)
set(_args USART ${link})
endif()
if(_ok)
pureboot_size_variant(pbm_${hz}_${baud}_${link} CLOCK ${hz} BAUD ${baud} ${_args})
endif()
endfunction()
# Clock points: the shipped-fuse floor (CKDIV8), the calibrated RC, and
# the crystal the stock build assumes (the tiny13's ladder is its own RC
# menu — it has no crystal option).
if(LIBAVR_MCU MATCHES "^attiny13")
set(_matrix_clocks 1200000 4800000 9600000)
set(_full_clocks 128000 600000 1200000 4800000 9600000)
else()
set(_matrix_clocks 1000000 8000000 16000000)
set(_full_clocks 128000 1000000 1843200 2000000 3686400 4000000 7372800 8000000
11059200 12000000 14745600 16000000 18432000 20000000)
endif()
# The exhaustive cross product: every clock a deployment plausibly runs
# — the internal oscillators, the shipped CKDIV8 floor, the plain
# crystals and the UART crystals — against every rate, against every
# backend. Beyond the ladder the list carries the slow rates a
# sub-megahertz oscillator is left with, which no ladder rate reaches
# (16000 Bd is the only rate the 128 kHz oscillator holds exactly); at
# the fast clocks those same rates also select the software UART's
# 16-bit _delay_loop_2 bit spin (two words more setup at each of its five
# sites), the largest image the space produces and a shape the ladder
# default — always the *fastest* rate a clock reaches — never picks.
#
# Every chip runs the full cross product: the size-bearing classes (flash
# addressing, hand-over shape, page size, USART inventory) are what make
# the image differ, and a chip outside them is expected to match its class
# — but "expected" is what a matrix is for, and the whole sweep is cheap
# enough to run rather than reason about. PUREBOOT_FULL_MATRIX is what
# selects it; the compact matrix below is the per-commit default.
get_property(_full_bauds GLOBAL PROPERTY PUREBOOT_BAUD_LADDER)
list(APPEND _full_bauds 16000 4800 2400 1200)
if(DEFINED ENV{PUREBOOT_FULL_MATRIX})
foreach(_matrix_hz IN LISTS _full_clocks)
foreach(_matrix_baud IN LISTS _full_bauds)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} software)
if(PUREBOOT_HAS_USART)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} 0)
endif()
if(PUREBOOT_HAS_USART1)
pureboot_matrix_point(${_matrix_hz} ${_matrix_baud} 1)
endif()
endforeach()
endforeach()
else()
foreach(_matrix_hz IN LISTS _matrix_clocks)
math(EXPR _matrix_khz "${_matrix_hz} / 1000")
if(PUREBOOT_HAS_USART OR NOT _matrix_hz EQUAL _pb_stock_hz)
pureboot_size_variant(pureboot_sw_${_matrix_khz}k CLOCK ${_matrix_hz} SERIAL software)
endif()
if(PUREBOOT_HAS_USART AND NOT _matrix_hz EQUAL _pb_stock_hz)
pureboot_size_variant(pureboot_hw_${_matrix_khz}k CLOCK ${_matrix_hz} SERIAL hardware)
endif()
if(PUREBOOT_HAS_USART1 AND NOT _matrix_hz EQUAL _pb_stock_hz)
pureboot_size_variant(pureboot_usart1_${_matrix_khz}k CLOCK ${_matrix_hz} USART 1)
endif()
endforeach()
list(GET _matrix_clocks -1 _matrix_top_hz)
pureboot_size_variant(pureboot_sw_wide CLOCK ${_matrix_top_hz} BAUD 9600 SERIAL software)
endif()
if(PUREBOOT_HAS_USART1)
pureboot_size_variant(pureboot_usart1 USART 1)
endif()
# One configured deployment end to end — a real board's shape rather
# than the stock assumption: the ATmega328P on its shipped 1 MHz fuses,
# the software UART on hand-picked pins (TX = PB1, RX = PB5), the ladder
# baud (9600). The full protocol suite runs against it, fixture
# application included, over the runner's GPIO bridge — proving the
# configuration plumbing produces a working loader, not just one that
# fits.
if(LIBAVR_MCU STREQUAL "atmega328p" AND DEFINED PB_DEVICE)
pureboot_size_variant(pureboot_custom CLOCK 1000000 SERIAL software RX pb5 TX pb1)
get_target_property(_custom_hz pureboot_custom PUREBOOT_HZ)
get_target_property(_custom_baud pureboot_custom PUREBOOT_BAUD)
get_target_property(_custom_link pureboot_custom PUREBOOT_LINK)
add_executable(pbapp_custom test/pbapp.cpp)
target_link_libraries(pbapp_custom PRIVATE libavr)
target_compile_definitions(pbapp_custom PRIVATE PUREBOOT_CLOCK_HZ=${_custom_hz}
PUREBOOT_BAUD=${_custom_baud} PUREBOOT_SOFT_SERIAL PUREBOOT_TX=pb1)
add_custom_command(TARGET pbapp_custom POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary
$<TARGET_FILE:pbapp_custom> $<TARGET_FILE:pbapp_custom>.bin)
add_test(NAME pureboot.custom
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
${PB_DEVICE} $<TARGET_FILE:pureboot_custom> ${PUREBOOT_SIM_MCU} ${_custom_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_custom_baud} ${PUREBOOT_EEPROM}
$<TARGET_FILE:pbapp_custom>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbcustom-work ${_custom_link})
set_tests_properties(pureboot.custom PROPERTIES TIMEOUT 180)
endif()
# The second USART, driven for real on one chip: instance selection is
# compile-checked everywhere, but only a live session proves the loader
# initialized and polls the USART it claims to. The fixture application
# banners on the same instance.
if(LIBAVR_MCU STREQUAL "atmega644a" AND DEFINED PB_DEVICE)
get_target_property(_usart1_hz pureboot_usart1 PUREBOOT_HZ)
get_target_property(_usart1_baud pureboot_usart1 PUREBOOT_BAUD)
add_executable(pbapp_usart1 test/pbapp.cpp)
target_link_libraries(pbapp_usart1 PRIVATE libavr)
target_compile_definitions(pbapp_usart1 PRIVATE PUREBOOT_CLOCK_HZ=${_usart1_hz}
PUREBOOT_BAUD=${_usart1_baud} PUREBOOT_USART=1)
add_custom_command(TARGET pbapp_usart1 POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary
$<TARGET_FILE:pbapp_usart1> $<TARGET_FILE:pbapp_usart1>.bin)
add_test(NAME pureboot.usart1
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbtest.py
${PB_DEVICE} $<TARGET_FILE:pureboot_usart1> ${PUREBOOT_SIM_MCU} ${_usart1_hz}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} ${_usart1_baud} ${PUREBOOT_EEPROM}
$<TARGET_FILE:pbapp_usart1>.bin ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbusart1-work usart1)
set_tests_properties(pureboot.usart1 PROPERTIES TIMEOUT 180)
endif()
# The autobaud variants driven end to end over the software-UART bridge (both
# under review — pureboot/autobaud.md): the host sends the 0xC0 calibration
# pulse, the loader times it, locks, and programs. Run on the near-flash 328P
# and the word-addressed 1284P — the two flash-addressing classes — and each
# at two clocks with the one binary, which is the clock-agnostic property
# autobaud exists for (test/pbautobaud.py). The fixture application banners
# over the same software link at the first clock's rate.
if(LIBAVR_MCU MATCHES "^atmega(328p|1284p)$" AND DEFINED PB_DEVICE)
add_executable(pbapp_autobaud test/pbapp.cpp)
target_link_libraries(pbapp_autobaud PRIVATE libavr)
target_compile_definitions(pbapp_autobaud PRIVATE PUREBOOT_CLOCK_HZ=1000000
PUREBOOT_BAUD=9600 PUREBOOT_SOFT_SERIAL PUREBOOT_TX=pb1)
add_custom_command(TARGET pbapp_autobaud POST_BUILD
COMMAND ${CMAKE_OBJCOPY} -O binary
$<TARGET_FILE:pbapp_autobaud> $<TARGET_FILE:pbapp_autobaud>.bin)
add_test(NAME pureboot.autobaud
COMMAND ${Python3_EXECUTABLE} ${CMAKE_CURRENT_SOURCE_DIR}/test/pbautobaud.py
${PB_DEVICE} $<TARGET_FILE:pureboot_autobaud> ${PUREBOOT_SIM_MCU}
${PUREBOOT_BASE_HEX} ${PUREBOOT_PAGE} $<TARGET_FILE:pbapp_autobaud>.bin
1000000 9600 ${CMAKE_CURRENT_SOURCE_DIR}/pureboot/pureboot.py
${CMAKE_BINARY_DIR}/pbautobaud-work)
set_tests_properties(pureboot.autobaud PROPERTIES TIMEOUT 240)
endif()
endif()
Reference in New Issue View Git Blame Copy Permalink